Search Documents

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Abstract-Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is confined by tectonic shear zones between marble and metapelites, extending laterally into the marble as tabular, pod or lenticular oreshoots (up to 50 m ?? 20 m ?? 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical profiles across mineralized zones confirm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the insitu supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly influenced by seasonal fluctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent flooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2 ~10-3.8 to 10-1.4) and oxygenated (fO2 ~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sulfides and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+ was transported into karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2 in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2 increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By R. C. A. Thurston

"The lack of notch ductility in structural steel in general, and in ship plate in particular, has been the object of widespread attention in the metallurgical world since the spectacular collapse of the ill-fated S.S. Schenectady in 1943. Numerous investigations have been carried out, many new tests have been developed, and a vast amount of useful data has been published, with the result that our knowledge is now far more advanced than it was at the time of this disaster. Interest has focused largely on the medium strength steels, and the various factors which cause a normally ductile steel to behave in a brittle manner in the presence of a notch and at relatively .low temperatures have been thoroughly studied.The literature available on high-tensile steels, however, is less extensive and the present paper is intended to supplement this information. Notch toughness tests have been carried out, at the request of the R.C.N., on a high-tensile manganese steel in the form of commercial ship plate. One of the newer tests, the tear test, and the Charpy V-notch impact test, were used to examine the characteristics of plate for the construction of an ice-breaker. About 250 plates, mainly in the thickness range from 11,4 in. to 1 % in., were tested. An an-alysis of the results obtained is presented, certain aspects of the tear test are discussed, and the correlation between the two types of test is studied. On the basis of information available from casualty ships, the plates, with few exceptions, were considered to be satisfactory."

Jan 1, 1959

By A. R. Sorta, D. C. Sego

ABSTRACT The settling, shear strength, and index properties of oil sands fines-sand mixture tailings (FSMT) for a wide range of solids and fines content are investigated. Results indicate that the liquid limit of FSMT obeys a linear mixture law. The fines-water ratio (FWR) governs the permeability of composite tailings (CT) and CT with comparable geotechnical behaviour can be produced from the same initial FWR mixtures. A phosphogypsum (PG) dosage > 900 mg/kg does not improve the dewatering behaviour of CT. The undrained shear strength of FSMT at the liquid limit is approximately 2.4 kPa, but is dependent on fines content at the plastic limit.

Jan 1, 2013

By Y. Q. Li, X. H. Long

In this work, structural and electronic properties of smithsonite (ZnCO3) and cerussite (PbCO3) as the typical lead-zinc oxide minerals is simulated by means of DFT. The calculated results could be concluded as: (1) The density of states (DOS) of Zn atom in ZnCO3 is nearer to the Fermi level than that of Pb atom in PbCO3, suggesting that the Zn atom of ZnCO3 is more active and easier to interact with water molecules and hydroxyl ions. Smithsonite, therefore, could be more readily depressed in the flotation process. (2) The bond population value of Zn-O (0.23) and C-O (0.92) in ZnCO3 is obviously larger than that of Pb-O (-0.01) and C-O (0.85) in PbCO3, indicating that the covalent characteristic of ZnCO3 is stronger than that of PbCO3. (3) It is shown that the charge of Pb (+1.32e) in PbCO3 is more positive than that of Zn (+1.22e) in ZnCO3, suggesting that cerussite is easier to interacting with HS- compared with smithsonite in the flotation process. In summary, the structural and electronic property of smithsonite is completely different with cerussite, leading to the difference of their flotation behaviour.

Jan 1, 2015

By Kurt F. Weitz

"The number of materials that can be classified as fillers covers an extremely wide range: this paper outlines those fillers of the industrial mineral type that find extensive application in the paint and plastics industriesIn the paint industry, mineral fillers are known as extender pigments. Extenders are added to paint and plastic compositions to (1) lower the cost and (2) rein-force or modify the physical properties of a composition.Commonly used extenders are classified according to chemical type and discussed in terms of the change in physical properties that they impart to a paint or plastic film. Available cost reductions and data on the consumption of extenders in the Canadian paint industry are also included."

Jan 1, 1970

By W. N. Hamilton

"Evaporites abound in the Western Canada sedimentary basin, recurring throughout the stratigraphic column and widely scattered over the basin region. Alberta, situated centrally over the basin, includes many of the evaporites within its borders, but only a few have the right geological conditions to form potential economic deposits of salt or gypsum. These include the Middle Devonian Elk Point Group and related evaporites, Upper Devonian Wabamun Group-Palliser Formation evaporites, and evaporites of the 'Triassic Charlie Lake and Whitehorse formations.Salt deposits underlie almost half of Alberta. The major deposits belong to the Elk Point Group, which includes thick salt units in the Lotsberg, Cold Lake and Prairie Evaporite formations. Another, younger salt deposit in the Wabamun Group has only local distribution. Elk Point salts have a maximum aggregate thickness of 430 m in east-central Alberta. The deposits deepen southwestward across the province, from minimum depths of210 m at Fort McMurray to 1820 m at Edmonton.The thickest, most extensive salt deposits are the upper Lotsberg and Prairie Evaporite salts. Both have excellent development potential. The upper Lotsberg is up to 150 m thick, consists of clear, very coarse crystalline halite with only minor impurities, and has a notable lack of non-salt strata in its succession. Analytical data for the Lotsberg Salt show extraordinary chemical purity. Prairie Evaporite Salt differs lithologically from the Lotsberg in having a significant non-salt component. The deposit is up to 200 m thick and consists of medium crystalline halite, brownish coloured and cloudy as a result of finely dispersed impurities. The main impurities-shale, anhydrite and dolomite-are most prevalent as interbeds in the salt succession, ranging from very thin laminae to beds several metres thick. Although of lesser purity, the Prairie Evaporite Salt is shallower, thicker and more extensive than the Lotsberg and the salt quality is quite acceptable for most industrial uses."

Jan 1, 1982

By M. Kreuh

Crystalline Mg(OH)Cl and amorphous Mg2(OH)3C1 were successfully isolated from a hydrolyzed molten salt electrolyte sample in this work, It was found that the chemical form and crystallinity of the hydroxylchloride were controlled by the cooling rate of the molten sample when it was taken. Crystalline Mg(OH)Cl could only be obtained by cooling the molten electrolyte sample at a rate not faster than 0.6 °C/min, Upon more rapid cooling, the hydroxylchloride species precipitated as Mg2(OH)3Cl, The behavior of these solid hydroxylchlorides when contacted with fresh and non-hydrolyzed molten electrolyte at 550°C was also examined, It was found that the Mg(OH)Cl rapidly dissolved in the hot electrolyte and did not decompose into MgO at that temperature as would be expected from the literature, The dissolution rate of solid Mg2(OH)3Cl was found to be so slow by comparison that it resulted in the complete decomposition into MgO which thereafter was incorporated into the electrolyte as a suspended solid phase rather than dissolution.

Jan 1, 2004

By J. E. Gillespie

Introduction Mineral wool may be defined as "rock, slag, or glass fibres made by a process of melting and blowing by steam or air, containing a minimum of oil and unfiberized material" (U.S. Bureau of Standards CS 117-44). The earliest production of the material was in Wales, about one hundred years ago. In the United States, the industry daces from 1870 when a plant, using slag as raw material, was established in Greenfield, New Jersey. It was not until 1897, however, that large-scale production was commenced on this continent at a plant in Alexandria, Indiana, which utilized rock from nearby deposits. Today, mineral wool is manufactured in many parts of the United States and Canada, the plants for the most part being in close proximity to deposits of suitable rock or to sources of slag. In the United States there are some seventy-five producers with a total annual capacity of nearly one million tons of wool. In Canada, in 1946, eleven manufacturers produced about fifty million square feet of batt-type mineral wool insulation material. Mineral wool is, perhaps, the most efficient of all heat-insulating materials and, moreover, it is fireproof, extremely durable, and insect- proof. Its high efficiency is due to the very low thermal conductivity of the fibres themselves and to the fact that the produce as marketed contains up to 90 per cent non-conducting air space. Depending on the degree of compression of the fibres in the manufactured product, the specific gravity ranges from 2 lb. to 10 lb. per cubic foot. Products Marketed Following are the principal forms in which mineral wool is marketed: Blanket. - Mineral wool with or without reinforcing on one or both sides, with various types of confining media, all suitably bound together.

Jan 1, 1948

By W. A. Lang

"I.-IntroductionAn attempt bas been made in this paper to provide a basis for appraisal of the future of the coal briquetting industry in Alberta by outlining the processes used for briquetting various ranks of coal, by specifying the requirements of a briquetted fuel, by indicating .the status of the industry in the United States, by giving developments in Western Canada, by assessing costs of processing, and by discussing briquetting researches in progress. Much of .the detail bas been omitted since this might mask, rather than reveal, the more important phases of the problem. Reference will be made when possible to published articles where many of the details can be obtained.It should be stated at the outset that, in the writer’s opinion, there are three possible developments in Alberta as regards briquetting: (a) an expansion of the briquetting of the fines of • non-coking and coking coals of semi-anthracite, and of low and medium volatile bituminous rank; (b) the processing of the fines of high-volatile C bituminous coals; and (c) the upgrading of the lower rank high-moisture sub-bituminous coals. Details of the chemical and physical properties of these coals can be obtained in publications of the Research Council of Alberta (1, 2), and of the Fuel Research Station, Bureau of Mines, Ottawa (3).Semi-anthracite and low and medium volatile bituminons coals occur in the mountain areas of Alberta, where, during the upthrust of the Rocky mountains, the coal beds served as the sliding surface. This resulted in the coals being; crushed and consequently they contain a h1gh percentage of fines. In some cases they are high in mineral matter and require to be cleaned before being processed. However, the cleaning of fine coal is both difficult and costly. Both the amount of fines present in the mine-run coal and the amount of mineral matter associated with the coal have increased through the introduction of mechanized mining and through the recovery of coal by stripping operations."

Jan 1, 1950

By A. F. Sirianni

The Peace River iron ore deposit represents the sole source of raw material for an integrated steel industry in Alberta. The ore has proved refractory to beneficiation by a number of techniques. A selective oil-phase agglomeration technique is described. Medium-grade concentrates, analyzing 48-53% Fe and 10-14% SiO2 were obtained with recoveries of about 75% of the total iron. These results appear to represent the optimum possible for this ore body.

Jan 1, 1977

By Daniel E. Walsh, P. D. Rao

"A four-inch compound water cyclone (CWC) was tested to evaluate its gold recovery characteristics when processing -4.8 mm run-or-pit, placer material. Neutron activated placer gold particles (840 to 37 microns) were used as radiotracers (/98Au) in a closed circuit ewe test loop to determine concentrator recovery; a procedure believed unique to this study. The effect on gold recovery of gold size and shape, feed pulp density, feed pressure, vortex finder clearance (VFC), ewe cone type, top-size of the feed solids, presence or absence of heavy minerals in the feed, and the quantity of-37 micron slimes in the feed was investigated in over 300 tests.CWC concentration ratio and the top-size of the underflow solids were both affected by cone type, VFC, and feed pressure. Gold recovery was significantly affected by gold size, gold shape, and concentration ratio. These effects are complex, because significant size-concentration ratio and size-shape interactions exist. Radiotracer techniques showed gold particles had a residence time within the ewe of approximately one second. This study suggests ewe gold recovery is a concentration. This work suggests ewe gold recovery is a function of particle size and shape, and the flow rate through the cyclone. CWC cone ""bed density"" is considered important only as a thin, protective layer, which shields coarser gold particles from the entraining currents and facilitates their movement through the CWC.IntroductionCompound water cyclones (CWC), or automedium cyclones, are enhanced gravity concentrators for the beneficiation for slurries of sand, coal, and ground ore (Fig. 1). They are called compound water cyclones because of the compound slopes of their basal cones (Fig. 2) and are operated to suppress classification phenomena in favour of gravity concentration effects. The compound water cyclone is not a new wet concentrator. It was developed in the late 1950s by Dr. Jan Visman through research sponsored by Canada's Department of Energy, Mines, and Resources. Since that time, it has become a common unit in coal washeries for cleaning fine coal. CWCs and other versions of concentrating cyclones have also shown promise for heavy minerals and precious metals recovery."

Jan 1, 1988

By R. A. Campbell

The electric smelting of five lowgrade Canadian manganese ores has been investigated at the Mines Branch, Department of Mines and Technical Surveys, Ottawa. Ferromanganese, silkomanganese, and spiegeleisen were produced 1by special smelting processes from these ores since the latter were too low grade to be treated by conventional smelting methods. In one case the results were considered to be sufficiently promising to justify the construction of a pilot plant, by the Company concerned, for the further development of the process.

Jan 1, 1956

By Brian L. Beninger

This paper discusses the application of the computer to coal preparation process predictions. In broad terms, the computer is used to perform two main functions. Firstly, the given float-sink analysis is interpolated and extrapolated to cover the entire actual range of raw coal specific gravity. Assumptions based on historical data must be made at times. Secondly, the partition curve, which, from historical data, defines the efficiency of a specific coal washing process, is applied to the washability data in order to determine the expected clean coal yield and quality. The vast amount of numerical work which is required to make a prediction of this type exhibits the need for computer methods in this area.

Jan 1, 1979

By Harold S. King

TWO summers ago I had the privilege of visiting No. 18 colliery at Glace Bay. Underground, we travelled along the haulage-way behind a powerful electric locomotive. The motor in this locomotive began to smoke badly and a carbon tetrachloride type of extinguisher was used several times during the trip. At the time, I noted a strong odour of phosgene. On my return to Sydney, I spoke to Mr. Harold Gordon, Assistant to the General Manager of the Dominion Steel and Coal Corporation, and warned him of the danger of using this type of fire extinguisher in confined spaces, since it is a well known chemical fact that phosgene, a dangerously toxic gas, is formed by the decomposition of carbon tetrachloride. This danger does not seem to be widely recognized, so it seems advisable that a more general warning be published. Attention was first drawn to the danger by the death of two men in the United States Navy Department subsequent to breathing fumes from carbon tetrachloride used in a fire, and when an employee of the Bureau of Mines also was overcome while fighting a fire with carbon tetrachloride liquid. These accidents led to an investigation of the decomposition products of carbon tetrachloride by a group of workers in the Research Laboratory of the Pittsburgh Experimental Station, U.S. Bureau of Mines, the results of which were published in the October, 1920, number of the Journal of the .Franklin Institute (1). Their experiments were conducted by two methods. The first consisted in applying the liquids to actual fires and -to hot metal in a closed room of 1,000 feet capacity, where the gaseous products, mixed with air, could be retained and analyzed. The second method was to pass the vapour:s in air through heated tubes of iron or quartz, where the humidity of the air and the temperature could be controlled.

Jan 1, 1939

By G. S. Hume

In the transformation of carbonaceous materials, such as peat, to coals of various grades, the changes are known to be both physical and chemical and the grade of coal finally produced depends on the stage to which alteration proceeded. Those changes, which are frequently spoken of as the results of metamorphism, are due to pressure with accompanying heat and, according to the amount of metamorphism to which the sediments with the included carbonaceous beds have been subjected, there is a gradation from peat to anthracite coal, and even to graphite. The improvement in the quality of the coal as a result of metamorphism is due to an increase of the carbon content of the coal and a corresponding loss of the volatile materials. This rise in the quality of the coal according to the degree of metamorphism is well illustrated by the coals of western Canada. In the Plains area, where the deformation and the attendant metamorphism of the sediments is comparatively small, the coals are lignites, whereas in the mountains, where deformation has been severe, the coals are semi-anthracites. Sub-bituminous and bituminous coals occur in the intervening areas. The same general relationship between the quality of the coal and the degree of metamorphism holds true for the Appalachian basin of the United States, where there is a progressive improvement in the quality of the coals from west to east, that is, from an area of comparatively slight metamorphism to an area of marked deformation in the Appalachian Mountain region. But while it is true that this relationship holds in a general way, it has been found that the improvement in the quality of the coal is not always uniformly progressive, and there may be local variations such that an area containing coal with a carbon content indicating low or medium metamorphism may be surrounded by areas in which the coals are of higher grade. These local variations in many cases can be explained, and they in no way detract from the general rule that, in a region exhibiting a progressive betterment in the quality of the coal from an area of low metamorphism to one of more marked deformation, the quality of the coal, i.e., the amount of fixed carbon in the coal, may be taken as an index of the degree of metamorphism of the coal as well as of the sediments in which it occurs, It has been pointed out (') that certain coals, such as cannels, are unreliable indicators of the varying degree of metamorphism because of the nature of the material from which such coal was derived. Such coals, however, are not known in western Canada and their behaviour need not here be discussed.

Jan 1, 1927

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By A. P. Paiva

The solvent extraction properties exhibited by some /V,N'-tetrasubstituted malonamides to efficiently and selectively recover iron(III) from concentrated chloride leaching solutions can be found in the recent literature. The iron(III) extractive chemistry exhibited by some of these derivatives is revisited, in order to compare their chemistry with that shown by a few of the new malonamide compounds. The generally good extraction efficiency towards Fe(III), from >4 M hydrochloric acid solutions, and the relative ease of Fe(III) stripping by distilled water are remarkable findings that are confirmed for the malonamide derivatives described in this work. Furthermore, additional data regarding their selectivity towards Fe(III) extraction over several base metal ions and their behavior when subjected to successive Fe(III) extraction-stripping tests are also presented and discussed.

Jan 1, 2006

By V. S. Papezik

Pyrophyllite, an AI silicate used in the production of ceramic materials, is formed mainly by alteration of felsic to intermediate volcanic rocks, either directly (at temperatures of 250-300°C and pressures of 1-2 kbar) or by subsequent low-grade metamorphism of aluminous protoliths produced by thermal fluids or even by prolonged weathering. Most pyrophyllite deposits in North America are concentrated in a belt of Late Precambrian volcanic and sedimentary rocks, the "Avalon Zone ", which extends along the eastern flank of the Appalachian mountain system from Newfoundland to the southeastern U.S.A. The only producing pyrophyllite mine in Canada is an open pit located near the settlement of Foxtrap on the Avalon Peninsula of Newfoundland. It lies in a belt of rhyolitic flows and pyroclastics intruded by a granitoid pluton. The rocks have been leached along a shear- or fracture zone, depleted in silica, alkalies, Ca, Mg and Fe by the action of hydrothermal fluids, and recrystallized to a very fine-grained massive assemblage of pyrophyllite, muscovite ("sericite") and quartz. High-grade pyrophyllite lenses contain small nodules of diaspore with minor barite; rutile is present in trace amounts. The close proximity of all pyrophyllitized zones on the peninsula to the granite contact suggests that the alteration was produced by thermal fluids genetically connected with the granitoid pluton. The fine-grained pyrophyllite-bearing rocks, with their simple mineralogy, are suitable for quantitative modal analysis by X-ray diffraction. Chemically analyzed samples from the alteration zone were used for the construction of working curves by plotting calculated mineral content against the intensity of selected diffraction peaks. The accuracy of the resulting curves is ±4.5% for quartz, ±3.6% for pyrophyllite and ±2.7% for muscovite. Pelletized samples give best results. The XRD method is suitable for a rapid analysis of a large number of grab or core samples to outline higher-grade areas for more detailed sampling.

Jan 1, 1978

By R. I. Cavanagh, A J. Last

THE USE of higher grade charges in blast furnaces in the form of sintered or pelletized concentrates has been increasing rapidly. The question of beneficiation of iron ores for this purpose is therefore receiving much attention as more deposits are developed. Many iron ores may respond well to magnetic roasting procedures followed by magnetic concentration, however, in most cases other more standard ore dressing methods are competitive and cheaper. For magnetic roasting as applied to iron ore beneficiation, the present question is "Can it be economically justified in situations where it appears to produce good results?" The following collection of information on the general status and operations of magnetic roasting methods may be helpful in considering this question. Magnetic Roasting Magnetic roasting involves the transformation of non-magnetic iron oxides, hydrated oxides and carbonates by means of heat and suitable

Jan 1, 1961

By L. E. Djingheuzian

Introduction For many years the immense deposits of bituminous sands of northern Alberta have been attracting the attention of our governments, engineers and .scientists ( 6). Undoubtedly these bituminous sands represent one of the greatest potential resources of liquid fuels in the world. However, their commercial development has been retarded by the complexities of the technological problem and by the economic factors involved in the processing of the sands. The technological problem has been attacked from several angles ( 2, 3, 1, 11), and cold water separation of bitumen is one of them. To the ore dressing engineer, the cold water process is of utmost importance since, by the use of standard ore dressing machinery, it accomplishes most efficiently and economically the separation of bitumen from bituminous sands. The significance of using ore dressing equipment was especially enhanced by the fact that the scientific principles which underlie the design of standard machines were demonstrated in the cold water separation process with an extraordinary clarity. This greatly facilitated the analysing of limitations and advantages of different machines during-the pilot plant investigations and helped to complete the investigations practically in the allotted time.

Jan 1, 1952