Search Documents

By Gibson I, Somerville J

Three main confined aquifers occur in interseam sediments beneath the planned excavation for the Loy Yang Brown Coal Open Cut. Sub-artesian groundwater pressures occur in all aquifers necessitating dewatering to prevent excessive seepage and depressurisation to prevent heaving of the open cut floor and batter instability. Reduction of water pressures in coal joints is also required to maintain coal face stability. This paper describes the depressurization and dewatering strategies, investigation for and installation of pump bores and groundwater observation bores. Approximately 5000m of drilling is carried out annually for dewatering at Loy Yang and both cable tool and rotary flush drilling methods are utilized. The cabletool method is used to obtain accurate samples for laboratory analysis, whereas rotary flush methods are used for speed and for installation of the larger diameter pumping bores. A method of re-establishing pump bores after partial excavation during mine development has been successfully developed with large cost savings. Trials are also being conducted with pre-collaring of deep bores with rotary methods then sampling the aquifer strata with a cable tool rig.

Jan 1, 1988

By W R. Hancock

Control of complex machinery through the internet is investigated through the construction of a vehicle prototype developed using off-the- shelf hardware. The vehicle was able to be controlled remotely through the use of a client side interface connected to a steering wheel and foot pedals. By attaching sensors to the vehicle, data could be collected from which one could infer the effectiveness of such a control system. The effect of latency on control was monitored by the introduction of an artificial latency, simulating a wide variety of internet-related issues, such as unstable connections and dropouts. Sensor data could then be used to gain an understanding of how the system could be improved though either control or interface design. A path tracking experiment was conducted to gather controllability data and it was found that such a system is plausible within a reasonable range of latencies. It is expected an area of future research would be an extension of this current project, applying the information gained to real world control systems.

Jan 1, 2008

The south-east Missouri cobalt-copper-lead-zinc district is the worldÆs largest lead producer and a significant producer of by-product zinc, copper, cobalt, silver and cadmium. Current production in the district comes from six or seven mines in the Viburnum Trend. Most ores in the Viburnum Trend are characterised by a small number of minerals with simple compositions. Portions of some orebodies contain ores that exhibit greater variations in mineralogy, and these include shale-hosted lead- copper ores, bornite ores and nickel-arsenic sulfide ores. Ore textures include both replacement and open space filling textures, and the paragenetic sequence for the ores is characterised by repetitive periods of deposition of all of the ore and gangue minerals. Ore microscopy is an effective tool for not only the identification of the minerals and textures shown by the ores, but also to determine the mineralogy and textures responsible for beneficiation problems. An interesting variety of sedimentary and structural ore controls have determined the locations of individual orebodies in the district. Based upon the positions of orebodies with respect to Precambrian ridges and knobs, together with areal patterns of mineral/metal zoning, it is interpreted that the ore fluids came from diverse directions to form the deposits in the district. It is concluded that the Old Lead Belt subdistrict was mineralised by fluids that flowed from the north-east and north-west, the Fredericktown area by fluids from the north-east, the Indian Creek subdistrict by fluids from the north-west and the Viburnum Trend by fluids from the north-west and west.

Jan 1, 2008

By Daziel M, Corke P

Unit cycles in mining have not changed for many years. Productivity increases over the past three decades have mainly been achieved by using larger and heavier machines. This investment in size has probably reached the point of diminishing returns and increased productivity in the future will have to be generated by other means. One way of achieving this is through automation of selected unit operations, eg dragline overburden removal, truck haulage, ground support installation and secondary breakage. Although, in the past few years, there has been significant progress in this direction, we are still a long way away from even partial automation - especially in hard rock mines. This paper addresses the technical obstacles facing mining automation; suggests ways by which these obstacles may be overcome and identifies the role of industry groups and research providers in this process.

Jan 1, 1997

By Hargraves A. J

At 4 MPa gas pres ure and 30°C the sorptive capacity of 10 selected Australian dried coal ranges from 17 to 23 m3/tonne of CH4 and 27 to 36 m3/tonne of CO2. Values for moist coals are about 25 per cent less. At 20°C, sorptive capacities are about 18 per cent greater. No clear relationship between coal rank and sorptive capacity was established.The permeability of coal to gas is dramatically reduced by progressive hydrostatic confinement. No single 'permeability' for a coal can be established because of relative affinities of coals and the gases (Ar, CH4 and CO2) used in experiments. Bedding plane permeability is significantly greater than permeability normal to bedding. Dependent on gas/coal combinations, permeabilities without confinement ranged from 150 to 0.05 millidarcies, and with 8 MPa hydrostatic confinement from 1.0 to 0.001 md. Generally, permeability is increased by reduction in temperature, and reduced by increase in moisture as one changes from Ar through CH4 to CO2. In retrospect, it is preferable to ubject permeability sample to 8 MPa hydrostatic stress only once, because changes occur in the samples and it is difficult to use other gases successively.The initial rate of desorption, DP, does not appear to be a reliable index of proneness to instantaneou outbursts for Australian coals.The methods used for determining quantitative gas-coal properties appear suitable and reliable for testing other coals.

Jan 1, 1985

By K Biegaj

The paper describes challenges the author has encountered on Australian underground gold and nickel mines over the last eight years, when recovering high-grade gold/nickel bearing mine floor material with a mobile supersucker/giant vacuum cleaner and other equipment. Whilst for a number of years the mine floor vacuuming and other mine floor clean-down technologies have been accepted/adopted and are working well in other parts of the world and on the South Australian opal mines, regrettably, they have not yet gained acceptance of mining executives and mine managers of gold and metal mines in Australia, who still elect to leave the never to be recovered gold/metal behind or to put it plainly - waste it.For reporting purposes during the mining process, the portion of gold/metal included in calculation of ore reserves prior to obtaining capital funds for their development, continues to be camouflaged in various reconciliation and call factors. This approach, ie wasting of capitally developed and already broken ore stocks should be viewed by the shareholders as totally inappropriate to say the least, especially with the current gold and other metals prices.The author attempts to provide answers as to why the technology referred to above has not yet been accepted on Australian gold and metal mines and outlines the way forward.CITATION:Biegaj, K, 2012. Why do shareholders and mining executives allow mine managers to leave behind high-grade broken ore underground?, in Proceedings Narrow Vein Mining 2012 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

The stratigraphy of the Singleton Coal Measures is reviewed and a revised stratigrapixy which has been ratified by the N.S.W. Standing Committee for Coalfield geology is nominated and defined by a selected type section. Withir the type section the occurrence of repetitive phases are illustrated and described. Coal. Measure units within the Singleton Coal Mean sures, termed the Wollombi and Wittingham Coal Measures respectively, are correlated with the Newcastle and Tomago Coal Measures. In formal nomenclature the Singleton Coal Measures are designated the Singleton Super Group. The major depositional cycles within the Coal Mea- sures are outlined together with those lesser phases within the Coal bearing sequences that influence the mining conditions likely to be encountered. Both tectonic and sedimentary features of the Singleton Coal Measures are considered and the localized post depositional effects on the coal seams and roof strata in- duced by differential, compactions are emphar Sized.

Jan 1, 1972

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

The Kyaukpahto gold deposit is located at latitude 23¦ 47Æ 55" N and longitude 95¦ 56Æ 35" E in the Kawlin-Wuntho district, Sagaing Division, Myanmar. Gold mineralisation is hosted in sandstone of the Male Formation (Eocene) and occurs as stockworks and disseminations. The high-grade gold mineralisation is locally concentrated in a breccia zone. The gold deposit is closely associated with a NNE-SSW trending fracture system that forms tensional open fractures. These tensional zones are thought to be directly related to the Sagiang transfer fault system that experienced several hundred kilometres of northward dextral movement during the post-Upper Miocene. Major sulfide minerals are pyrite and arsenopyrite with minor galena, chalcopyrite and sphalerite. Gold mineralisation is associated with intense silicification, sericitisation and argillic alteration. Primary Type I fluid inclusions in the quartz from the mineralised zone are 5 to 15 ¦m across and yield homogenisation temperatures of 239¦ - 310¦C and salinities of 1.2 - 10.9 wt per cent NaCl equivalent. Laser Raman spectroscopic analysis indicates the presence of CO2 and CH4 in Type II fluid inclusions. Sulfur isotope analysis of disseminated pyrite in the ore zone by the laser ablation method indicates d34S values from -5.48ë to +5.53ë. The geology, alteration, ore mineralogy, fluid inclusion microthermometry and sulfur isotope data of the Kyaukpahto deposit are consistent with an epithermal ore deposit model for the deposit. However, the presence of CO2-liquid bearing fluids and the detectable CH4 in the gaseous phase of the fluid inclusions conflict with a typical epithermal origin for the Kyaukpahto deposit. The host siltstone and mudstone sequence, trace element geochemistry, and the disseminated nature of sulfide and gold mineralisation are also common characteristics of a sedimentary rock-hosted gold deposit, and these features may indicate a Carlin-like affinity. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By T Davis

The 500 orebody in the upper levels of Mt Isa Mines in north-west Queensland was mined by sublevel caving and block caving from 1962 to 1969. The hot and reactive rock mass of this orebody provided significant mining challenges including ground temperatures above those resulting from the geothermal gradient. Recently Xstrata Copper has been studying the potential to mine this orebody by modern caving techniques. Part of the study process has included re-accessing the ore zones for diamond drilling and trial development. A cross-cut trial drive, the first primary development into the orebody in more than 30 years, encountered a temperature increase in development holes from low sixties to almost 80¦C in less than 10 m advance. The issues associated with managing this risk include sourcing suitable quantities of reactive ground explosives for a single small heading and the temperature limitations of the explosives and detonators. Risk management outcomes included controls to mitigate the safety and reliability risks relating to misfires. The control that dealt directly with the challenge of continuing development in elevated temperature ground was to cool the holes before and during charging. The most effective and practical cooling medium proved to be water. Rapid rock temperature recharge time meant cooling had to continue as close to firing as possible. Reticulation systems were constructed to allow cooling to take place up until withdrawal for firing. No misfires occurred with the cooling system and additional controls in place. This proved that developing safely and effectively in the elevated ground temperatures of the 500 orebody is practicable.

Jan 1, 2008

By C Kusi-Manu, E Nyamusika

Geita Gold Mining Limited (GGML) is owned and jointly managed by Ashanti Goldfields Company (Ghana) and Anglogold (South Africa). The mine is currently one of the largest gold producing open pit operations in Africa producing 620 000 ounces of gold and mining in excess of 70 000 000 tonnes of material per annum. The mine currently has 2000 full time employeeÆs and a mine life in excess of 12 years. Geita Gold Mine is comprised of 11 different gold deposits situated in the Lake Victoria Goldfields of North Western Tanzania (Figure 1). The gold deposits are primarily associated with banded ironstone formations within an Archaean greenstone belt. Current global resources, including Inferred, stand at 129.5 million tonnes grading 3.91 g/t (16.2 M oz). Open pit reserves total 70.4 million tonnes grading 4.16 g/t (9.4 M oz). The majority of the gold resource is hosted by the three deposits (Nyankanga, Lone Cone and Geita Hill) within the æGeita TrendÆ a large and continuous (>4 km long) mineralised zone (Adofo, 2002). Geita Gold Mine commenced operations in June 2000, as the second large-scale open pit gold mine in Tanzania. The new workforce of 800 people had no previous experience in open pit gold mining. Since the start of the operation, Geita Gold MineÆs management ambition was to become a world leader in the application of best practice in all technical disciplines and in operational success. Staff development and training was identified as one of the major components in the company achieving its aim. Geita Gold MineÆs management has committed the necessary training staff, resources and the commitment of over $US 1 M a year to staff training and development programs for 2003 and 2004. The process and management of Geita Gold MineÆs mining geology staff training and development program is presented in this paper.

Jan 1, 2003

It is difficult with inadvertent explosions to establish fundamental data, especially of original dust, of pressure, temperature etc. and of ventilation oscillations, as exposed personnel rarely survive. Retrospective data from explosions must be derived from damage, from fatalities, from ventilation analyses, from analyses of dusts and other indications of temp- erature and duration of temperature. The five disastrous explosions selected for analysis provide examples of what data can be established as to the cause and extent of explosions. Such information is required for legal etc., inquiries subsequent to explosions, but most importantly to give the best guidance for avoidance of possibility of further Disasters.

Jan 1, 1981

By Jiang G

The Chinese Central Government attaches great importance to the development of its coal industry. Besides carrying out the policy of simultaneous development of large, medium and small coalmines,the main strategy is to gradually modernize coal mining areas and coalmines and to increase the output from individual coalfaces. There are particular implications, processes and main experiences of coalmine modernisation in China.Ensuring a coal output of over one M tonne/yr from one coalface is a very complicated system-engineering project which deals with a wide range of problems. The most important measure used for achieving an output of over one M tonne/yr from a single coalface is the analysis of affecting factors on coalface production by means of the theory c reliability. Thus, as far as possible , the production stoppages caused by mechanical equipment failures and other factors are avoided, the equipment recovery rate is increased and the working hours of shearers are extended so as to ensure a high output and high efficiency.

Jan 1, 1991

By Poplawski R. F

A 32-channel PSS seismic monitoring system was commissioned at Mt Charlotte mine in 1994, and at the time it was the first such system in Australian mines. The system continuously observes the occurrence of seismic events and locates them accurately in space and time. Mt Charlotte has a history of seismicity, with the largest event in recent years of Richter magnitude 4.3. The decision to 'go seismic' was made despite some uncertainty regarding its potential usefulness. However after the first year of operation, benefits have been realised in terms of less production downtime, improved mine safety and mine planning, and better understanding of the nature of Mt Charlotte seismicity. The seismic network has performed well, recording 550 events in its first year of operation to a location accuracy averaging ¦ 12 metres. System reliability is excellent, with very little downtime, and acceptable operation and maintenance times and costs. Observations show major distinct changes in the rate of mining induced seismicity over time periods of weeks and months. Events have tended to cluster in specific mine areas and on particular faults and structures. Case examples of pillar preconditioning, breakout around an orepass, and a major stope rockburst, illustrate the role of seismic data and the benefits it brings to safety, productivity and planning.

Jan 1, 1995

There is considerable economic incentive to increase the angle of open pit walls so as to reduce the total volume of waste to be moved to gain access to an orebody. However, a number of slope failures has increased the awareness of mine operators to the potential and consequences of slope failure. Sophisticated methods for the analysis of slope stability have been developed but they rely on an understanding of the appropriate parameters to describe the structural properties of the slope materials. Unfortunately, these properties change with time.The excavation of an open pit mine removes the constraint and weight of the overlying material and allows the newly formed slope to release previously locked in stress. The release of this stress allows the opening of joints and leads to a significant reduction in bulk modulus. The rock mass is also further affected by damage from nearby blasts. Such damage is cumulative and further reduces the modulus of the near surface material and weakens the bonds between structural elements in the slope.

Jan 1, 1992

By E S. B Santiago, C P. N Moreto, L V. S Monteiro, G H. C Melo, R P. Xavier

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Iron oxide-copper-gold (IOCG) systems of the Carajás mineral province (Amazon craton, Brazil) are structurally controlled by regional-scale shear zones and have formed by multiple episodes of fluid circulation and hydrothermal alteration in the Neoarchean (2.71–2.68 Ga and 2.56 Ga) and Palaeoproterozoic (1.90–1.87 Ga).Collectively, fluid inclusion, boron, oxygen and hydrogen isotope data and Cl/Br–Na/Cl ratios in fluid inclusions reveal that regional circulation of non-magmatic brines (eg evaporative fluids/evolved sea water) and mixing with other fluid sources (eg meteoric or magmatic) is an important attribute in the genesis of the Carajás IOCG systems. The ?33S and d34S compositions of sulfides from the Neoarchean and Palaeoproterozoic IOCG systems suggest that the ore-bearing fluids have assimilated sulfur from crustal reservoirs. Nevertheless, most ?33S measurements have indicated mass independent fractionation (MIF) effect for both systems which points to the possible involvement of surface sulfur sources.CITATION:Xavier, R P, Monteiro, L V S, Moreto, C P N, Melo, G H C and Santiago, E S B, 2015. Non-magmatic versus magmatic fluids in the genesis of Archean and Palaeoproterozoic iron oxide-copper-gold systems of the Carajás Mineral Province (Brazil), in Proceedings PACRIM 2015 Congress, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Stitt P. H

This paper provides a brief historical review of the invention of the spiral separator and its adoption into Australian metallurgical practice. The purpose of the review is to demonstrate that spiral development to date appears to have been a largely empirical process, and that the cur- rent resurgence of interest in the spiral, especially in the coal industry, warrants an increased fundamental research effort. Current research work concentrating on empirical modelling is outlined, while some preliminary experimental results of a more fundamental nature are presented and some research of other disciplines interested in particle transport introduced in order to stimulate further work and discussion.

Jan 1, 1988

By Kokubu H, Moro-Oka A

Gaseous desulphurization from hot metal- lurgical slags containing sulphur mainly as sulphide and(or) sulphate was measured under `low at four different oxygen pressures. The total gas rate was from 1.7 to 2,8 litre/min. Crushed slag samples weighing 2 to 12 g were used for the experiments. The amount of SO2 gas evolved from samples kept at 15500 was rieasured over tires ranging from 20 to 300 min. The gaseous desulphurization rate of sul- phide sulphur becomes high as the oxygen part- ial pressure is increased, while that of sul- phate sulphur is high under low oxygen pressure. The effect of basicity on the desulphurization rate of sulphide sulphur in oxygen atmospheres is not obvious in the range of basicity from one to three. Changes in the ratio of sulphide to sulphate sulphur during the run in oxygen axe analysed. Desulphurization reactions and the rate controlling steps are discussed. De- sulphurization phenomena can be explained by inte.-¦ucia.l chemical reaction rate control.

Jan 1, 1980

By Fazakerley VW

The Murrin Murrin deposit is located about 210 km NNE of Kalgoorlie and 50 km E of Leonora in the North Eastern Goldfields region of Western Australia at latitude 28¦ 50'S. longitude 121¦ 54'E on the Laverton (SH 51-2) 1:250 000 map sheet. The tenements are held by Anaconda Nickel NL. Geological investigations between 1994 and 1996 resulted in resource calculations being completed for the ten lateritic nickel cobalt deposits shown in Figure 1. At a 0.8 per cent nickel cut-off the resources at May 1996 for the nine deposits are 116.8 Mt at 1.10 per cent nickel and 0.082 per cent cobalt. The nickel-cobalt mineralisation is contained in a laterite profile developed over Archaean serpentinised peridotites. A bankable feasibility study has been completed and the project is scheduled to be in production by the beginning of 1998.

Jan 1, 1996

By Woodcock JT, La Broody SR

As part of a project on the application of thiourea leaching to a variety of Australian ores, the systematic variation of pH, redox po- tential, and thiourea concentration were in- vestigated on an oxidized gold ore from the Nevoria mine, WA. Stirred open beaker tests were conducted with a pH-stat and Eh-stat system to automati- cally control pH and redox potential at selected values, while thiourea concentration was main- tained manually. Increasing the acidity of the leach liquor from pH 3.6 to pH 1, increased the gold extrac- tion from 37 per cent to over 90 per cent in S h, but there was only a limited improvement below pH 1.5. Silver extraction and thiourea consumption increased as the acidity was in- creased. Increasing the redox potential from 150 to 200 mV (i.e. potential of Pt electrode vs SCE) increased the initial rate of gold and silver extraction, but the effect on cumulative gold extraction by 5 h was slight. Thiourea consump- tion was greatly increased as the redox poten- tial was increased. An increase in thiourea concentration from 1.2 to 4.8 per cent increased the initial rates of gold and silver extraction, but, as for the change in Eh, the improvement in cumulative ex- traction by 5 h was marginal. Thiourea consump- tion increased with thiourea concentration.

Jan 1, 1984