Search Documents

Review of the mining legislation in New Zealand has coincided with a number of radical changes. These include a redirection of economic management towards a more open and competitive economy; major reform of the state sector aimed at greater efficiency, transparency and accountability; a new environmental administration; and a fundamental review of policy for management of natural and physical resources. These changes provide an opportunity to develop a consistent and coherent approach in the minerals and related statutes that will achieve objectives of economic efficiency, equity, practicability and good environmental management.

Jan 1, 1987

By L Dixon, J Carter, K Auyong

Fourier transform infrared (FTIR) spectroscopy and other near infrared (NIR) tools have been used in the bauxite industry for many years. Infrared spectroscopy exploits the differences in chemical composition and lattice structure to produce a characteristic response. Spectral devices, such as those from ASD Inc and the HyLoggerTM, provide qualitative mineralogical data targeted towards hydrated minerals detected in the near and short wave infrared region. The FTIR spectrum extends into the mid and thermal infrared range and can therefore respond to the presence of silicates and oxides, in addition to hydrates and carbonates.The key to successful utilisation of infrared spectra, however, is the interpretation methodology. In this study, FTIR spectra were calibrated against quantitative X-ray diffraction data for the determination of the mineralogy of iron ore. A full pattern profiling machine learning technique was utilised for the calibration, and the assessment of the regressions determined from an independent validation set. The abundance of key minerals – hematite, goethite, kaolinite and quartz – were determined and the results correlated against X-ray fluorescence assays and loss on ignition data. The results of the study indicate that spectral techniques using a full-pattern profiling machine learning approach and artificial neural networks can be used successfully to obtain objective and quantitative mineralogical data to support field observations and analytical results for iron ore resource modelling. A comparison of this technique to the cost, quality and timeliness of other quantitative mineralogy tools is also made.CITATION:Carter, J, Auyong, K and Dixon, L, 2017. Determination of iron ore mineralogy using Fourier transform infrared spectroscopy and machine learning, in Proceedings Iron Ore 2017, pp 519–528 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M Bird, B Oats, M Sganzerla

Mining operations are continually aiming to reduce operating costs to improve plant profitability. One way in which the Cannington operation sought to achieve this was by increasing the wear life and reducing the energy consumption of their flotation mechanisms. This was made possible using Outotec’s FloatForce mechanism. The FloatForce mechanism has been developed by Outotec over a six year period involving both CFD modelling and rigorous site testing. FloatForce delivers improved air dispersion and cell agitation efficiency; as such it can be operated at lower rotor tip speeds when compared to Outotec’s previous mechanism.Cannington trialled three FloatForce mechanisms in a train of ten OK38 zinc roughers. The mechanisms’ rotational speed was reduced by 10% compared to the previously installed MultiMix mechanisms. The purpose of the trial was to quantify the energy saving and assess whether there was any reduction in plant metallurgical performance.The trial was successful with FloatForce delivering a 17% reduction in power, an improvement in wear and improved recovery. Analysis of pre and post-installation metallurgical accounting data showed the following:The FloatForce installation resulted in a recovery increase of zinc to zinc final concentrate of 0.4 – 4.0%*The FloatForce installation resulted in a recovery increase of lead to zinc final concentrate of 0.0 – 0.3%*There was no statistically significant change in silver recovery to zinc final concentrate that can be attributed to FloatForce**95% confidence interval (CI) using multiple linear regression models.The Cannington operation is now in the process of further optimizing its power consumption and wear savings by changing the remaining OK38 zinc and lead rougher float cells to FloatForce mechanisms.CITATION:Bird, M, Oats, B and Sganzerla, M, 2015. Improvements in flotation cell maintenance, power consumption and operation at South32 Cannington, in Proceedings MetPlant 2015, pp 230–245 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By G Mark, K L. Blake, G de Jong, J F. Rotherham, N D. Adshead

Magnetite deposits with distinctive ¦ actinolite ¦ apatite-bearing gangue and spatially-extensive sodic-calcic wall rock alteration occur in both Proterozoic metamorphic terrains and Mesozoic-Tertiary magmatic arcs. Examples from both settings constitute significant sources of iron ore (egKiruna, Sweden; El Romeral, Chile) and some host major Cu-Au deposits that have a local association with K-silicate alteration (eg Cloncurry district, NW Queensland; Copiapo district, Chile). A growing body of evidence points to a hydrothermal origin for these systems involving high temperature, low S oxidised fluids. The Cloncurry magnetite-Cu-Au deposits are products of the local structurally channelised influx of a specialised high salinity ore fluid into larger-scale alteration systems developed during pluton emplacement at greater depths than those associated with subvolcanic (porphyry) Cu-Au deposits. The geological characteristics of deposits in magmatic arcs are consistent with a similar mode of origin albeit in rather different tectonic settings.

Jan 1, 1995

By M J. Andrews, P J. White, I Bogie

Active geothermal systems occur widely in Sumatra and in the Taupo Volcanic Zone (TVZ) ofNew Zealand. There are also many occurrences of epithermal gold mineralisation in Sumatra, some of which are economic. Minor sub-economic occurrences of gold have been reported in the TVZ but none have yet been mined. There are both similarities and differences in the nature of the active geothermal systems and mineral deposits in Sumatra and New Zealand, which can be systematically related to the tectonic setting. The thicker crust and consequent predominance of silicic volcanism in New Zealand leads to hydrothermal systems which are little eroded and with limited lateral outflows. The systems in Sumatra are of mixed character, with some of the characteristics of those in andesitic island arcs such as Java or the Philippines, e.g. a higher proportion of systems with identifiable acid magmatic volatiles, a greater potential for deep erosion and lateral outflows than in New Zealand; but modified by the more oblique component of subduction and thickened crust so that some are localised in volcano-tectonic depressions and consequently have high piezometric levels of primary hydrothermal fluid. The unusual occurrence of calcic zeolites in veins associated with gold mineralisation in Sumatra is thought to be indicative of æsatelliteÆ boiling zones along de-gassed hydrothermal outflows.

Jan 1, 1995

Prior to 1972, Peko Mines Limited at Tennant Creek used a central mill at Peko, which consisted of a gravity circuit, flotation and cyanidation of tailings, to treat their gold ore from surrounding mines. The Warrego concentrator, 60km to the west, was built to handle the Warrego and Gecko copper orebodies, which were being developed concurrently with the concentrator construction The Warrego concentrator consisted of a flotation circuit, using autogenous grinding at 100 - 120 tph, compared to the more elaborate Peko circuit employing rod mill - ball mill grinding capable of treating only 18 - 26 tph. During development of the Warrego copper mine a gold rich ore pod was located, because of which the mining plans were adjusted to allow simultaneous, separate extraction of the copper and gold ores. However, the plans for the concentrator were not affected as the gold ore could be carted 60km to the Peko central mill for processing.

Jan 1, 1978

The extractive industry has been faced with a situation where there has been no systematic and formalised training and education structure available. Previous structures which were available, e.g. the quarrying diploma and the mining papers as a part of an engineering degree, have suffered the same fate as the Dodo. They are now extinct.   In providing for a training strategy, the past strategies need to be examined and reasons behind their demise examined. This paper examines the reasons for past failures in education and training in the extractives industry, the factors that need to be taken into account in creating an education and training culture, the strategies required, the Government regulations and trans-Tasman agreements, and the quality management which must surround the entire training programme.

Jan 1, 1997

According to the data provided by the most recent European Survey on Working Conditions, roughly 25 per cent of the European working population is exposed to mechanical vibrations for no less than one quarter of the work shift duration, while around ten per cent are exposed for the entire work shift. The occupational exposure to whole-body vibration (WBV), in particular, represents a major health risk in mining, quarrying and civil excavation activities. In accordance with European Directive 2002/44/EC, the latest version of the Italian law on physical risks has recently confirmed the possibility of using relevant literature data on vibration magnitude in order to evaluate personal occupational exposure (vibration database or data provided by the manufacturer). Still the alternative option, based on field measurements, represents the most appropriated method of risk assessment, as it accounts for the actual operating condition at the workplace; actual operator and vehicle under investigation and specific working cycle. The article discusses the vibration measurements taken on a number of heavy machinery (excavators, loaders, trucks, dumpers, etc) employed for talc extraction in a mine located in Sardinia and the resulting personal exposure for the drivers. The assessment was carried out in accordance with the specifications of ISO 2631-1 and EN 14253.

Dec 6, 2010

I would like to thank The Australasian Institute of Mining and Metallurgy for inviting us to share with you some of our experiences in the handling, storage, and transportation of industrial minerals in North America. Cometals, Inc. is a wholly-owned subsidiary of Commercial Metals Company, headquartered in Dallas, a public corporation whose shares are traded on the New York Stock Exchange. Sales exceed one billion dollars. Cometals, Inc. is located in New York and specializes in marketing of chemicals as well as raw materials used in the manufacture of steel, refractories, abrasives, glass and ceramics. This makes us one of the larger regular shippers of industrial minerals. Many people are aware that industrial minerals need to be viewed and judged on the merits of their chemical and physical characteristics. In addition you are surely aware that close attention must be paid to the economics of these minerals to determine the appropriate value and competitiveness of the minerals or products delivered at the doorsteps of the consuming work. You may, however, not be aware that the handling and transportation of the mineral is of crucial importance, in fact, the transportation and handling costs of industrial minerals frequently are a major component of the value of the ores marketed and, therefore, it is only natural that close attention should be paid to them. Many of the industrial minerals require special handling to assure that the material reaches the consumer without being contaminated and without getting wet. I invite you to accompany me through the various steps involved in "delivering the goods" to the consumer.

Jan 1, 1989

At its Port Kembla Plant, Australian Fertilizers Ltd. manufactures Superphosphate and other Phosphatic Fertilizers.Phosphate Rock is received from Nauru and Ocean Island. It contains water insoluble tri-calcium phosphate, Ca3(PO4), to an average of about 86%.It is crushed to pass a 20-mesh x 26-gauge woven wire screen, and is then treated with Sulphuric Acid to give the product Superphosphate with a water solubie prosphate content of 20.5%, estimated as P205. Sulphuric Acid is made by the chamber process. Three sets of chambers are installed, on,e five-chamber set of timber frame work construction and the other two of more recent date, each with four chambers of steel frame work construction. A fourth chamber set is now being built.Sulphuric Acid is delivered for use. at about 70% H2S04, the strength depending upon the rock used.Mixing - The crushed rock and sulphuric acid are mixed in weighed and measured proportions respectiyely in one-ton batches in revolving cast fron pans, mechanically stirred. The mixture, while still slurry, is run into a closed horizontal concrete cylinder (den) where, with the completion of the chemical reaction, it rapidly sets as Superphosphate.Approximately fifty batches are required to fill a den. When full, the den is opened ana the mass cut out by a revolving cutter. The product is elevated and conveyed to any required position in the Superphosphate storage shed, where it dries and matures.Despatch - As required, the Superphosphate is excavated by a two ton grab and conveyed from the matured "dump" to bagging units where it is disintegrated, screened and bagged at twelve bags to the ton. The filled !Jags are closed by machine and delivered to railway trucks immediately.Mixed Fertilizers - Sulphate of Ammonia, Sulphate and Muriate, of Potash, and Blood and Bone are mixed with Superphosphate and thoroughly incorporated to give different mixtures to meet special plant requirements.

Jan 1, 1938

Since the end of World War n, many important developments have taken place in the investigation of the phenomenon of brittle fracture in mild steel. Fractures in certain classes of welded ships, in welded bridges, penstocks, etc., focussed a great deal of attention on the interrelationships of design factors, service conditions, and steel quality on the generation of catastrophic failures.Much publicity has been given these major failures, and there is perhaps a tendency to forget that mild steel, under certain conditions, as well known to behave in a brittle fashion in a wide range of everyday engineering applications.For instance, many who are connected with the haulage and lifting of heavy loads will be familiar with the bright "crystalline" fractures of crane hooks and chains which sometimes follow sudden jarring; those concerned with the heavy pressing and shaping of steel plate will not be unaware that at times sudden brittle splits or tears will develop for no obvious reason in, say, rolled pipes or in dishings.In fact it will be evident upon reflection that in many cases the conditions which mild steel has to withstand during processing into an engineering part or structure are more severe than those it wili be called upon to endure during service. In this sense brittle fractu;res in mild steel are much more frequent than are commonly supposed.Two modes of fracture are now generally recognised to occur in metals, namely, shear and cleavage. The latter manifests itself by the so-called "crystalline" fracture (here...

Jan 1, 1954

Bendigo Mining operates a 600 000 t/a comminution, gravity, flotation and leaching processing plant for the recovery of gold from their Kangaroo Flat Operation, in the Bendigo goldfields. The free gold and gold bearing sulfi des present are typically coarse grained and hence are highly amenable to gravity recovery. Plant operating data is consistently showing that over 78 per cent of the feed gold is recovered in a circuit, consisting of inline pressure jigs, inline spinners followed by free gold tabling and intensive leaching of tabling tails. The circuit receives coarse crushed product from high pressure grinding rolls and the grinding mill discharge, which allows material to be re-circulated through the gravity process until the particles are small enough to enter the flotation circuit. A plant audit was completed on 26 November 2009 designed to give an indication of the overall operational characteristics of the gravity circuit including single pass efficiencies of associated equipment. The techniques, results and challenges of such a survey are discussed.

Aug 1, 2010

The Detachment of Coarse, Composite Particles from Bubbles

Sep 13, 2010

By Ibil S

The Gameta Gold Deposit is located on the north-eastern corner of Fergusson Island in the D'Entrecasteaux Islands of Milne Bay Province, PNG, at lat. 9¦ 25' 5, long. 150¦ 47' E or AMG co- ordinate 256740 E/8959000 N (Figure 1). The area is covered by the Fergusson (SC56-05) 1:250,000 scale Topographic Map Sheet and the Koitabu (9079)1:100,000 scale Topographic Map Sheet. The property is held 100% by Union Mining NL (UMG) and lies 105 km NNE of Alotau and 33 km to the ESE of UMGs recently developed Wapolu Gold Mine, a Joint Venture between UMO (51%) and Macmin NL (49%). The inferred resource estimated from surface results and 105 RC drill holes, currently stands at 1.89 million tonnes at 2.6 git gold (1.0 g/t Au cut-off) or 155,000 oz. Evaluation of the property is currently proceeding. To date 111 RC holes have been drilled for a total of 4611 m.

Jan 1, 1997

Using DEM to Model Industrial Banana Screens

Sep 13, 2010

The emergence of China as a global economic power has not been without its birth pangs and the current coal market is testimony to this. Traditionally the coal market has been controlled by mature economies that functioned along balanced lines of supply and demand. The emergence of China and India as major forces in the international market has shifted this balance of power from mature economies to the developing economies of China and India. Of late Chinese Central Government policy has caused wide swings in the supply of Chinese coking coal and thermal coal to the international Asian markets. This has resulted in huge increases in demand for coal from producers in Australia, Canada, Indonesia, USA and Russia. Additionally since the late 1990s the liberalised Chinese economy has been growing by between nine to 12 per cent per annum. The corresponding rise in the standard of living of their 1.4 billion people has resulted in a strong demand for raw materials, initially met by domestic production and more recently met by the importation of raw materials including iron ore, oil, coking coal and thermal coal. Commensurate with this growth in China has been the emergence of India (pop one billion) as another major developing economy in the region. Whilst the Indian standard of living is lower than that of the Chinese, this subcontinent still has some 300 million people with middle class consumption demands. India is a major importer of oil, coking coal and thermal coal. It exports iron ore to China with growth parallel to China (seven to nine per cent per annum). These combined new demands from India and China have put unprecedented pressure on the global supply of coking and thermal coals. These pressures are reflected in the current world spot prices for coking and thermal coals which are at historically high levels. Whilst current demand from China and India is high it is anticipated that new projects will partially satisfy this increasing demand. Expectations are that overall thermal and coking coal prices will rise steadily. This paper seeks to identify the potential effects of Chinese and Indian economic growth on the international markets for coal.

Jan 1, 2004

Factual data about the sedimentation in the Newcastle Coal Measures are presented. Data concerning the total coal measure sequence (isopachs, sand/shale ratio, and total coal thickness variation), data about three coal seams (Borehole, Dudley, and Victoria Tunnel) and data about interseam conglomerate units are discussed.From this data conclusions are drawn about the coal measure environment. The western edge of the coal basin, the Lochinvar Dome, although a high feature, was apparently stable during coal measure time. Despite its height it apparently supplied little sediment to the basin.The northern and north-eastern edge, which was unstable, supplied most of the coarse detritus (including the conglomerates) to the basin. The conglomerates show patterns of fluvial origin but after a period of "normal" variations in pattern they become restricted to two parallel zones evidently tectonically controlled. Deposition of conglomerates is episodic and separated by periods of coal formation when deformation was apparently slight. Formation of each of the three seams considered followed a rather similar pattern- each show development of thick coal around the basin edge and poor thin coal in the "axial" region of the present synclinal structure.Evidence of ill situ formation of some areas of the seams is discussed and periodic deformation of the basin during coal measure time is postulated.The unusual character of this coal basin, in particular the very coarse units, is stressed, despite the presence of many "normal "coal basin features.

Jan 1, 1970

Approximation of Surface Area of Fines in Blast Induced Fragmentation The surface area of fragmentation, especially in the finer size fractions, is a useful property to characterise the mechanisms of rock breakage. In the past, researchers have made assumptions with regard to the shape of fragments in order to estimate surface area, such as that all fragments are the same shape or all fragments are spheres. Often these assumptions were developed with inappropriate measures and returned considerable variability and error for the calculation of surface area. This paper reports a model to estimate fragmentation surface area from sieve sized raw data and a density measurement, with experimental validation down to a size fraction of -45 + 38 ?m in a range of rock types. After characterisation of particle shape, a range of fragment shapes was found to be in each size fraction. Nevertheless, in the ?2 sieve series the average fragment mass, volume and the size fraction standard deviations could be predicted reasonably accurately. Ellipsoid geometry was used to describe particle shape. Using these parameters and the number of fragments (also predicted) in each sieve size the individual surface area of each fragment was simulated.

Sep 13, 2010

In the last two years the Commission for the Environment has received four Environmental Impact Reports (EIR) for Audit and has been or is involved with at least four environmental impact assessments (EIA) related to mining. The EIRs have included Weavers Coal Mine, the Monowai-Maratoto mining proposal, the Martha Hill mine and the Wainui Road Mill. The EIAs are related mainly to coal fields in the Waikato but also included a further EIA on Martha Hill.

Jan 1, 1986

An investigation into the causes of variable sulphur content in blast furnace metal produced at No. 4 blast furnace at the Port Kembla works of Australian Iron and Steel Pty. Ltd. was carried out. Theprogramme included an extended and detailed experimental study of a great number of the operating variables of the furnace, on a cast-bycast or four-hourly basis, over fourteen days.Possible causes of the variation were found in irregular operation due to sinter variability, and it was also clearly shown that slag conditions were most important in controlling sulphur contents of pigiron. Some decrease in sulphur variability was achieved, arising partly from this investigation, and it is hoped to try magnesia additions to modify slag conditions for better desulphurizing.INTRODUCTIONSulphur in pig iron is a problem common to many blast furnace operators throughout the world, but the direct causes and means of overcoming them are functions of the available raw materials, and are hence more particular to each plant and its operating practice. Sulphur in hot metal influences the steel-making operations, the rolling operations and the quality of the finished steel. The main problem associated with high sulphur in steel is "hot shortness", which leads to cracking of ingots and billets in rolling, to poor surface finish and to poor welding properties in the finished steel. On the other hand, sulphur is sometimes a desired additive to steel in order to promote free machining properties.Normal means of controlling sulphur A small degree of control of sulphur in steel is available to open hearth operators by alteration of slag volumes and basicity, but any large degree' of sulphur elimination is...

Jan 1, 1961