Search Documents

By Harry K. Ihrig

THE hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1/8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was, necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes Co. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.11 The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 DESCRIPTION OF TEST METHOD The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1945

By E. P. Burtchaell

A method is presented for evaluating the effect of gravity drive upon the reservoir performance of a high relief pool. Conventional forms of reservoir analysis do not consider the alterations in the basic material balance data caused by gravity segregation of reservoir fluids. A procedure is outlined for structurally weighting physical and chemical data for use in the material balance equation. It is demonstrated how actual pool performance data can be utilized to evaluate the future reservoir performance of a gravity drive pool. INTRODUCTION Conventional reservoir engineering. procedure is inadequate for the analysis of an oil pool which has considerable structural relief, steep dips, and good permeability development. In, pools of this type, gravity drainage has an important part in the movement of oil to the wells and the effects of gravity on the overall pool performance should be included in any analysis of reservoir behavior. Many engineers have the opinion that the force of gravity in the movement of oil is not important until the later life of a pool.' Probably the basis for this belief is that gravitational effects may not be readily discernible until a pool is nearing depletion. This would be especially true for pools not having a high degree of structural relief and permeability development. Actually the effects of gravitational forces are at a maximum when the pool pressure is high, for during this period the hydrostatic head of the oil column is at a maximum and the viscosity of the oil is at a minimum. Oil recoveries from pools having favorable gravity drive characteristics may equal or even exceed recoveries which might be expected from water displacement. Field evidence indicates that in some reservoirs gravity drive has resulted in recoveries greater than that which could have been expected from gas expansion or water drive.'.3 Unfortunately, the possible effects of gravity drive on pool performance have been underestimated and other reasons have been sought to explain the high recoveries obtained. There are unquestionably many reservoirs to which the principles of gravity drainage can be effectively applied. It is the purpose of this paper to illustrate one method whereby gravity drive is included in the reservoir analysis of an oil pool. A hypothetical pool, typical of many California reservoirs, is used as an example. As used in this paper, "gravity drive" is defined as the overall effect of gravitational influences on the recovery of petroleum from the reservoir; "gravitational segregation" as the gravity separation of oil and gas within the reservoir; and "gravity drainage" as the downward movement of oil as caused by the force of gravity. SAND VOLUME DATA Fig. 1 presents a structural contour map of the pool under study. Maximum closure is 1950 feet with dips on the south flank approaching 45". The original gas-oil interface was set at -5200 feet. Average thickness of the producing sand was 200 feet. For use in subsequent calculations ill this paper, the pool was subdivided into 100-foot vertical increments and the sand-volume content of each increment was obtained. If the gross sand thickness is small, under 100 feet, the sand-volume content can be obtained by superimposing an isopachous map upon a structural contour map and planimetering the average thickness of each 100-foot increment. For sand thicknesses over 100 feet, one approacli would be to construct a sufficient number of cross-sections of the pool from which the weighted sand-volume of each 100-foot increment could be obtained. Variations in the sand body with depth, as determined by core data, can also be included in the above process. Table I presents a summary of sand-volume calculations, core data, and the original distribution of reservoir hydrocarbons in the pool. Fig. 2 illustrates the structural distribution of the sand-volume content. A total of 171,398 acre-feet is contained within the productive limits of the pool. Assuming an average porosity of 25% and an interstitial water content of 20%, the original hydrocarbon content was computed to be 227,075,000 barrels. DEPTH-PRESSURE DATA The determination of the initial vertical pressure arrangement in the pool is necessary for PVT and material balance calculations. Whenever sufficient data are available, a plot of pressure versus subsea depth of measurement should be made. From this plot a representative fluid pressure gradient can be established. Lacking sufficient initial pressure data, an initial pressure gradient may he estimated or calculated from avail-

Jan 1, 1949

By E. Miller, J. M. Eldridge, K. L. Komarek

Activities of magnesium in liquid Mg-Sn alloys have been determined between 5 and 90 at. pct Sn and 990" and 1290°K by an improved isopiestic method wherein tin specimens, heated in a temperature gradient and contained in crucibles of special geometry, were equilibrated with magnesium vapor in a closed titanium system. The crucibles were designed so that the equilibrium compositions of the specimens were satisfactorily preserved on termination of the experimental runs by quenching. The activity values are in excellent agreement with those predicated on the phase diagram and allowed a delineation of the solidus curve of the compound Mg2Sn near its melting point. EQUATIONS have been recently derived relating the chemical potentials of the components to the liquidus and enthalpy data for binary systems exhibiting one congruently melting compound.' The liquidus curve of the Mg-Sn system between the eutectics was carefully redetermined and the thermodynamic properties thus calculated were in reasonably good agreement with values derived from electromotive-force measurements of an,' but differed greatly from the iso-piestically determined values of Ashtakala and Pid-geon.3 The present study was initiated: a) to resolve the discrepancies; b) to develop a method for measuring activities in systems having volatile (and possibly highly reactive) components; and c) to use the method in a general investigation of the thermodynamic properties of the homologous series of Mg-Group IVb systems, i.e., Mg-Pb, Mg-Sn, Mg-Ge, and Mg-Si. This paper describes the results for the Mg-Sn system. An isopiestic technique, originally developed by Herasymenko 4 and adapted for alloys having a component of high reactivity and low volatility,5-8 was modified in this study by using crucibles designed to preserve the equilibrium composition of highly volatile liquid specimens on quenching from high temperatures. Tin specimens, contained in tightly covered graphite crucibles and heated in a temperature gradient, were equilibrated with magnesium vapor of fixed pressure from a magnesium reservoir kept at constant temperature in a previously evacuated and sealed titanium tube. During equilibration magne-

Jan 1, 1967

By P. D. Zemany, G. W. Sear, B. W. Roberts

Vanadium metal is embrittled by hydrogen at a temperature as low as 250°C when held in the presence of manganese metal and water vapor in a rough vacuum. It is established that the property changes are caused by the catalytic decomposition of water vapor at the vanadium surface and the diffusion into and solution in the vanadium of the resultant hydrogen. It is found that manganese is a necessary component of the catalyst. The manganese is transported in the vapor phase by an unknown molecule. A deuterium tracer experiment demonstates the role of water vapor in the embrittle-ment process. VANADIUM metal foils were observed to become embrittled' at a temperature of about 300 °C when held in the presence of manganese metal and a small amount of moist air, This paper describes the investigation to find the embrittling agent and an understanding of the relatively low temperature reactions that are involved. Experimental The vanadium metal foil used was prepared by cold-rolling and pack-rolling 32 mil sheet" in a series of steps down to 1 mil foil. The original observation was confirmed by sealing vanadium foils of 3 x 10 sq cm into individual Pyrex tubes with manganese powder† and a con- trol tube containing only the vanadium foil. These tubes were evacuated to 10 -5 mm Hg without baking and sealed. After heat treatment for 200 hr at 300°C, the control foil showed no change in duetility, whereas the foil contained in the manganese— containing tube was embrittled. The visual appearance of each was unchanged. A series of Pyrex sample tubes, about 2.5 cm diam and 25 cm long, were prepared, each containing a 3 x 10 sq cm piece of foil and 5 g manganese powder at the lower end of the tube. By reducing the time of anneal and the temperature of these samples, it was found that embrittlement could be created at 250°C in a time as short as 1 hr. Since the vanadium metal used here has been drastically cold-worked by rolling, it is assumed that it contains a maximum number of dislocations. To check the possible necessity of dislocations in this low temperature reaction, a vanadium foil sample was annealed in Vycor for 2 hr at 800°C to re crystallize and reduce the dislocation concentration. Metallographic examination showed grains which were not visible before annealing. The embrittlement procedure was carried out at 300°C and 3 hr. Upon checking the foil no embrittlement was observed. Further experiments demonstrated that about 6 hr at 300°C are required to create embrittlement in the foil. This delay in the onset of embrittlement in the vanadium foil suggests but does not prove that dislocation channels play a role in the embrittlement phenomena. If manganese metal is necessary for this low temperature embrittlement, do other elements in the transition metals group yield the same result? To check this qualitatively, a group of elements of similar atomic radii were obtained and sealed as before into Pyrex tubes with a sheet of vanadium foil. These tubes were annealed at 250°C for 6 hr and included (with radii)-2 A1 (1.4A), As (1.25A), Be (1.2A), Co (1.25A), Cr (1.45A), Cu (1.25A), Fe (1.25A), Ga (1.2A), Ge (1.25L%), Mn (1.3A), Ni (1.25A), Si (1.2A), Ti (1.45A), Zn (1.3A), air, H,O, 10 cm Hg of dry hydrogen, and MnO, powder. Upon testing the above sample foils for brittleness, only the manganese-containing tube yielded a brittle foil. Manganese Transport—To eliminate contact of manganese metal powder and vanadium foil, sample tubes were prepared with fritted glass barriers. The embrittlement reaction was still found to occur. Thus, the mode of transfer of manganese is certainly vapor transport. A vanadium foil was embrittled by this mechanism in an evacuated Pyrex tube for 8 hr at 300°C. By means of X-ray fluorescence analysis,' the amount of manganese added to the surface was established at 5 ±2 x 10 -6 g per sq cm. Since the average rate of manganese deposition is known, an effective average pressure of an assumed carrier compound can be computed. ___ P = M/T v2p mkT

Jan 1, 1959

By N. J. Grant, C. C. Wang

The Ti-Cr-O ternary system has been studied in detail near the titanium-rich corner within the limits of 10 wt pct 0, and 20 wt pct Cr. Studies were extended, but not in detail, to the region beyond 25 wt pct 0, (50 atomic pct) and 62 wt pct Cr (60 atomic pct). Four isothermal sections at 1400°, 1200°, 1000°, and 800°C are presented as well as two vertical sections at 1 and 2 wt pct 02. DURING the last decade much interest has been shown in the development of high strength titanium alloys for high temperature and corrosion resistant applications. Extensive research is being carried out at present, as the current literature indicates, in order to study the properties of titanium and to develop improved alloys. Two of the important alloying elements in commercial titanium alloys are chromium and oxygen and it would be desirable to know their combined influence upon titanium. For this purpose the present work was carried out to investigate the titanium-rich corner of the ternary system TiICr-0. The binary systems Ti-Cr and Ti-0 have been published recently. The Ti-Cr system was studied by several investigators " and their results are in close agreement. The eutectoid decomposition of the B phase has been shown to be extremely sluggish. TiCr, was the only intermetallic compound found in this binary system and was formed at 1350°C by a transformation from the p phase. TiCr? was established as the cubic C 15 (MgCu,) type of structure with 24 atoms per unit cell and was designated as the y phase. This terminology will be adopted in the present work. There was disagreement about the actual composition of this compound among the several investigators, although it is evident from their data that the compound probably has a solubility range of about 2 to 3 pct and is in the vicinity of 65 pct Cr. It has been indicated recently that a high temperature modification of this y phase (TiCr,) existed at a temperature above 1300°C." ' This high temperature modification was identified as a hexagonal C 14 (MgZn,) type of structure with 12 atoms per unit cell. The exact transformation temperature from the high temperature phase to the low temperature phase has not been established. A considerable hysteresis was observed and, due to the sluggishness of this transformation, the high temperature phase often co-existed with the low temperature phase at temperatures below 1300°C. A preliminary study of several Ti-0 compounds and the Ti-0 system had been carried out by Ehr-1ich."-"' The most complete binary Ti-0 system was the one reported recently by Bumps, Kessler, and Hansen." The first intermediate phase found in the system was the 8 phase which formed by a peritec-toid reaction of the phases a and Ti0 at temperatures below 925 °C. This reaction is extremely sluggish. The structure of this 8 phase was tentatively identified by these authors as being tetragonal and the lattice constants were found as c,, - 6.645A, a,, = 5.333A and c/a = 1.246A. Experimental Procedure The raw materials used for this investigation were TiO,, electrolytic chromium, iodide titanium, and sponge titanium. The TiO, was in the form of powder of chemically pure grade (99.8 pct pure). The chemical analysis of the electrolytic chromium was: 0, 0.50 pct; Fe, 0.07; Cu, N, and C, 0.01; and Pb, 0.001. The oxygen in the chromium was calculated as part of the final oxygen content of the alloys. The alloys were prepared by the cold crucible method using a tungsten arc. The entire system was evacuated and flushed with purified helium three times and then filled with helium. Each alloy was melted, turned over, and remelted at least four times to insure homogeneity. The total melting time was generally from 6 to 10 min. A master alloy of 25 pct 0,-75 pct Ti was prepared to facilitate alloying by melting compacts of TiOl powder with either iodide or sponge titanium, yielding the compound TiO. It was found necessary to bake the TiO, powder compact at about 150°C to remove adsorbed moisture. This was done to prevent the disintegration and spattering of the compact when the arc was struck. TiO, powder dissolved quite readily into the melt and no other trouble was encountered.

Jan 1, 1955

By G. Sachs, A. W. Dana, C. C. Chow

A great number of the investigations on the plastic flow of metals have been concerned with the establishment of a "universal" stress-strain relation. In such a relation some stress function when plotted against a strain function should yield identical curves for the various stress states. In the first investigation of this type, Ludwik and Scheu1 plotted the maximum shearing stress as a function of the maximum principal strain. Later Ros and Eichinger2 introduced two universal stress-strain relations, the one relating the maximum shearing stress to the maximum shearing strain, and the other relating a stress invariant, suggested by von Mises and Haigh, to the corresponding strain invariant. (In more recent investigations the stress and strain invariants are frequently supplemented with some factor to render their meaning more lucid.) A further suggestion which has not attracted appreciable attention is that by Baranski³ who used stress and strain deviators. The most common means of experimentation to determine the relation between stress and strain consists in subjecting thin walled tubes to combined internal pressure and axial tension.4a,4b,4c This method allows the study of plastic flow under stresses which are variable in two directions. However, the plastic flow which can be obtained in this manner is comparatively small, being limited by either tension failure or instability. For copper,'. only the relation between maximum shearing stress and maximum shearing strain yielded good agreement. On the other hand, tests on a stee14b and on an aluminum alloy4c. resulted in systematic deviations if any of the discussed universal stress-strain relations were used. It would seem, therefore, that the agreement mentioned above for copper is only incidental and explained by its high rate of strain hardening compared to that of other metals. Much larger strains than experienced in the tube tests can be obtained by subjecting a thin membrane of a ductile metal, which is restrained at its periphery, to a uniform hydraulic pressure. The thin sheet forms a deep bulge before it fails. The stresses and strains in such a bulge increase with increasing distance from the edge of the clamping "die," the maximum stresses and strains occurring at the pole (crown) of the bulge. While the stress and strain states are determined by the contour of the bulge, the absolute magnitude of the stresses and strains depends upon the hydraulic pressure. The bulge contour is in turn correlated with the geometry of the die opening. The deformation and fracture characteristics of circular bulges, that is, bulges formed with circular clamping dies, have been the subject of numerous experimental and analytical investi-gations.5,6,7 It has been shown that plastically deformed circular bulges develop large and comparatively uniform strains before failure by instability"6b,6c,6d and closely assume a spherical shape.6d Also the distribution of strains across the contour of the bulge is dependent on the metal being investigated and is correlated with, but cannot be predicted from, the metal's stress-strain characteristics. On the other hand, oblong or elliptical bulges, that is, bulges formed with elliptical clamping dies, are not as susceptible to analytical analysis and have not been investigated to the extent that circular bulges have. The few available data6c,7c indicate that stress states are obtained at the poles of the bulges, varying between plane strain and balanced biaxial tension, depending upon the geometry of the die opening. In this paper, the strain state and curvatures exhibited by three bulge shapes, a circular and two elliptical bulges, Fig 1, are analyzed experimentally using methods described in previous publications.6a,6c An attempt is made to derive the stress-strain relations for these bulges, which represent strain states in which the ratio of the two positive principal strains varied between 1.0 and 0.35. In addition, tension tests yielded data for a value of —0.5 for this strain ratio. Such an analysis should indicate the applicability of the various laws correlating stress with strain to the stress and strain states occurring in bulged shapes. Definitions and Nomenclature The definitions of the major stress and strain quantities used in this paper are as follows: s1, s2, s3 = principal normal stresses Sl > s2 > S3 t = shear stress e = conventional (unit) strain e = In (1 + e) El, E2, E3 = principal natural strains 7 = shear strain The maximum shear stress: , _ S1 — S3 lmax = 2 Frequently, the flow stress, s1 — s3 = 2lmax rather than the maximum shear stress is used.

Jan 1, 1950

By James J. Halbouty

The restraining effects of war conditions on oil-field development are well illustrated by statistics on South Texas † fields for the year 1942. Statistics also show a decline in wildcatting, but this decrease is much smaller than that shown by field activity. In comparison with results in 1941, there was a reduction of about 44 per cent in the total number of wells drilled in the area (802 in 1942 against 1452 in 1941) This 44 per cent drop represents declines of 50.4 per cent in field wells and of 17.4 per cent in rank wildcats. Field wells (exclusive of 18 wildcats that discovered fields) totaled 598; also, 204 rank wildcats were drilled (see Tables 3 and 4). The corresponding figures for 1941 are 1205 field and extension wells and 247 rank wildcats. In this connection, it should be noted that whereas in 1941 the rank wildcats made up only 17 per cent of all wells drilled in the area, their percentage of the 1942 total was 25.4 per cent. In spite of the decrease of 43 in the number of rank wildcatst drilled, there were 18 new productive areas discavered, one more than the 17 new fields found in 1941. Thus the field-discovery rate for 1942, one new field for every 11.3 wildcats drilled, compares favorably with the I to 14.5 rate of 1941. Thirteen new producing levels were opened in fields; this includes the finding of 44' gravity crude on the west flank of the Sejita field in a 5700-ft. sand, which produccs distillate higher on the structure. Interesting, and showing the general scarcity of sand discoveries, is the fact that of the 13 new sands discovered, 7 were found in Jim Wells County. The year's sand-discovery rate of one new level for every 46 field wells compares very unfavorably with the I to 19.7 rate of 1941, during which 61 new producing horizons were found. Developmeilt of new fields was on a small scale. In several instances activity in these areas was not carried beyond the drilling of the discovery well. The field discoveries of 1942, together with the type of production obtained from the discovery wells and the total number of wells (productive and dry) drilled in them, are given below: Discovery Num- Field.I County Well her Produced Wells I. Cadena....... Duval Oil 2 a. Garza......... Duval Oil I 3. Dinn......... Duval Gas I 4. Keller......... Duval Gas I 5. East.......... Tim 0 11 I 6. Green Branch . McMullen Gas 3 7. Frost. .GreenBranch........ Starr Oil I 8. Garcia........ Starr Oil 6 9. Ulrich........ Starr Oil 4 10. Lykes......... Webb Oil 2 11. McLean....... Webb Oil 9 Iz. Alamo........ Hidalgo Distillate 2 and gas 13. Penitas....... Hidalgo Distillate 2 and gas 14. Xmpnan..... Jim wells i a 15. South Premont Jim Wells Distillate i and gas 16. Quinto Creek.. Jim Wells Gas 4 17. Roth.. . :..... Jim Wells Gas I I 18. South Sinton.. San Distillate I Patricio and gas . • See Table 2 for data on discovery wells and Table I for information on these fields. • See Table 4.

Jan 1, 1943

By L. W. Reynolds, R. F. Campbell, K. G. Carroll, S. H. Ballard

Based on metallographic and X-ray data probable equilibrium conditions from 1340" to 2400°F are presented for the composition range investigated. These are correlated with investigations of Takei and Kuo. Provision is made for existence of Mo, C and (Fe, Mo)2,C, carbides heretofore omitted in diagrams in this composition range. These carbides and (Fe, Mo),C, in equilibrium with ferrite and austenite, restrict the austenite and austenite + ferrite fields to lower carbon contents and higher temperatures than in the Fe-C system. OK groups of steel of different molybdenum content, but with approximately the same carbon variation in each group, Table I, were studied. The alloys were melted in an acid-lined 30-lb high-frequency induction furnace, and the ingots forged to l-in. rounds, which were then ground to 0.75-in. diam. To minimize chemical segregations a short length of each bar was given a high-temperature heat treatment as listed in Table I. Specimens 0.062 to 0.125-in. thick were thereafter cut from the homogenized bars for heat treatment to determine phase changes in the alloy. Heat treatments were performed in either a lead bath or muffle-type electric furnace, depending upon the temperature required. Maximum temperature variation was * 2" F in the lead bath and * 5"F up to 1900°F and +8"F above 1900°F in the electric furnace. Adequate protection of the specimen from the oxidizing atmosphere in the electric furnace was obtained by sealing the specimen in either a pyrex or a silica capsule which was evacuated or not as circumstances required. For austenitizing followed by quenching to an isothermal temperature, the specimen was placed in a closed-end refractory tube the mouth of which, extending beyond the furnace, was connected to a vacuum pump. The specimen could be withdrawn from this tube and quenched as desired. IDENTIFICATION OF PHASES The principal method of identification of phases was metallographic examination conducted on surfaces well removed from exposure to lead or atmosphere effects during heat treatment. Hardness measurements (Dph/lOkg) were also made on these surfaces. The etching reagents used and their effects are listed in Table II. Martensite and ferrite were readily recognized by their customary appearance after etching with saturated picral or 1 pct nital. The presence of liquid at high temperature was indicated by curved interfaces characteristic of boundaries between solid and melt, by intergranular pools of dendritic areas in a carbide matrix, and by a black network coincident with austenite grain boundaries. Examples of these structures are shown in Figs. l(a) and (0). The types of carbide which were attacked by the electrolytic chromic acid etch and the alkaline KMnO, etch, Table 11, were identified by X-ray analyses of extracted carbides of five alloys. Carbide residue was obtained from a metallographic specimen by etching the specimen for 24 hr in hydrochloric-picric acid in alcohol (grain-size reagent), after which the carbides, standing in relief, were scraped from the surface of the specimen and mounted on a glass slide. Diffraction patterns were obtained with a Philips spectrometer using iron-filtered cobalt radiation. Figs. 2, 3, 4, and 5 illustrate typical etching behaviors with chromic acid and alkaline KMnO,. Chromic acid attacked Mo,C as shown in Figs. 2(a) and (b)-but not (Fe, Mo),C, Fig. 3(b). Alkaline KMnO, attacked (Fe, Mo),C, Fig. 3(c), and also attacked M0,C. In accordance with these behaviors, a typical differentiation of coexisting Mo,C and (Fe, Mo),~ is shown in Figs. 4(a) and (b). The carbide (Fe, Mo),,C, could not be obtained free of other coexisting carbides for etching experiments. The behavior. however. of coexisting carbides identified by x-ray diffraction as Mo,C ind (Fe, Mo),,C, indicate that (Fe, Mo)23C6 is not etched by chromic

Jan 1, 1961

By M. H. Loveman

THE orebody described below has been rediscovered and developed within the last 3 years. It has, however, been known and worked by the Chinese for hundreds of years. When assay values and size are considered, it contains what is probably one of the largest single bodies of zinc and lead sulphides yet found. The tonnages developed at other places, as at Broken Hill, are much greater but the average zinc and lead sulphide contents are considerably lower than at Bawdwin. Bawdwin is situated in the semi-independent State of Tawng Peng, one of the numerous units which make up the Northern Shan States. These States are under British rule and are generally considered as a portion of Burma. They are governed as a separate administrative unit, however, under the Lieutenant Governor of Burma. Each State is under its own chief, or Sawbwa, who has considerable power over his own subjects. Bawdwin is approximately in latitude N 23°6', longitude E 97°20', about 50 miles south of the nearest point on the Chinese border and 450 miles north of Rangoon (Fig. 1). The period at which mining was first begun at Bawdwin is unknown. The most reliable records have been obtained by deciphering local Chinese inscriptions and from these it is concluded that the work dates back to at least the beginning of the 15th century. The first undoubted reference to the mines by a European is by Symes in 1795. Crawford in 1827 estimated the output of silver from the mines at $600,000 annually. At about the middle of the 19th century the rebellion of the Chinese Mohammedans in the neighboring Chinese province of Yunnan so weakened the power of the Chinese that the incursions of hostile tribes (Kachins) made work extremely dangerous. The mines were finally abandoned by the Chinese about 1868. The closing down of the mines was probably not entirely due to outside causes but may have been influenced somewhat by the increasing difficulty of handling the water, as the workings gradually descended below the water level of the district. Several attempts were made by the Burmese kings, Mindon Min and Thebaw, to resume operations, but because of a

Jan 12, 1916

By C. B. Manula, H. Gezik

In planning modem-day mining operations, management needs to pass from the area of subjective decision-making to an area of objective decision-makirlg. Planning procedures currently being practiced by many mine managers depend primarily on common sense and trial-and-error methods which oftentimes never reach optimum solutions. For this reason, an attempt is made to provide an understanding of linear programming to solve production planning problems. More specifically, a linear programming model is proposed to solve the production scheduling problem as it was found to exist in the crushed stone industry. Optimal production scheduling is of prime concern here, since the industry has to cope with seasonal demands for its products. The solution, as determined through the application of the model, provides management not only with an optimal production schedule but also with the following information regarding the improvement of existing facilities: (I) the location of bottlenecks which limit production and profit; (2) the directions in which the company i fixed equipment should be expanded or modified; and (3) the evaluation of unused resources. Future trends in stone production will quite likely parallel those in the construction industry. Continued record expenditures for structures such as dams, highways, and buildings are the reasons for this accelerated growth. Production forecasts for the next decade are predicted to be around one billion tons with an approximate 7% annual increase. The problem of increasing production from 570 million tons in 1966 to 1 billion tons by 1976 offers no small challenge. This situation is further compounded by other problems and economic factors. Population expansion, government regulation, labor agreement, and changes in technology wd cause managers and operators to be confronted by many more complexities than characterize present-day operations. Some of these. problems and economic factors are: (1) In some metropolitan and other urban areas, easily accessible sources of stone are almost depleted. Transportation costs will be a prime concern of the industry. (2) Population growth has forced residential expansion to a point where many quarry operators must conform to urban and suburban regulations. (3) Government regulation in regard to air and water pollution, noise, and reclamation as well as zoning developments necessitate that crushed stone producers keep abreast of changing conditions and requirements. (4) The crushed stone industry operates under pressure of a highly competitive situation. Every company's objective is to retain a favorable marketing position by exercising great attention to production and marketing costs. This is rather difficult, since the crushed stone industry is one segment of modern mining which has to cope with a seasonal demand for its products. Among the problems posed here, the one of exercising great attention to production and marketing costs is of current interest to management. Under seasonal demand conditions, this problem creates further difficulties for managers who need to plan and forecast. STATEMENT OF THE PROBLEM Various methods of Operations Research have been developed to handle a problem whose genesis is explained above. It is very seldom, however, that these quantitative means are used in practice by the mining industry. This paper describes the use of Operations Research methods to solve a production planning problem when demand is seasonal. The seasonal production planning problem is an important one because of the substantial costs associated with changing production, employment, and inventory levels to adjust to seasonal sales patterns. Most companies try to operate within reasonable levels of employment changes and hold inventories within storage capacities. In general, little or no attempts were made to develop minimum cosl schedules or to provide objective means to compare various production policies. When demand varies within a fixed time period, 11:-oduction requirements may be met by following one

Jan 1, 1970

By M. B. Bever, A. B. Michael

The solidification of aluminum-rich aluminum-copper alloys was investigated for different solidification rates. The measured amounts of nonequilibrium eutectic were compared with the amounts calculated on the assumption of no diffusion in the solid. The morphology of the eutectic was studied and dendritic spacings were measured. Compositions of the cored primary solid solutions were determined by quantitative autoradiography after activation of the solute copper by neutron irradiation. CONSIDERABLE progress has been made in recent years toward an understanding of the solidification of metals. This is especially true for the factors involved in nucleation, the controlled growth of metal crystals from melts, and various aspects of the freezing of ingots and castings. Many features of the solidification process, however, are not understood adequately and much further work is required. In the research reported here the solidification of a series of aluminum-rich aluminum-copper alloys was investigated. Different degrees of deviation from the idealized case of equilibrium solidification were attained by varying the rate of solidification. Thermal analysis and microscopic examination were supplemented by lineal analysis and autoradiography. The latter required the use of radioactive tracers and was adapted to the quantitative determination on a microscale of concentrations of copper dissolved in aluminum. The tracers were produced in situ by activating the copper with neutrons. These techniques permitted a correlated interpretation of the temperature-time history, the amounts of nonequilibrium eutectic and the general morphology of the alloys, and yielded quantitative data on microsegregation. Nonequilibrium Solidification In the general case of the solidification of a solid solution in accordance with the phase diagram, the composition of the coexisting liquid and solid must change continuously. This change requires diffusion, which at best remains incomplete in the solid during solidification. The resulting inhomogeneity of the solid solution crystals is well-known as coring, dendritic segregation, or microsegregation. The generally accepted analysis of coring assumes that, 1—no diffusion occurs in the solid, 2—diffusion is complete in the liquid, and 3—the composition of the solid formed on cooling through any infinitesimal temperature interval is given by the solidus of the phase diagram. On this basis, In this equation m designates mass, x designates the concentration of solute and the subscripts L and S refer to the liquid and solid phases, respectively; the subscript o indicates the initial state, in which the liquid is identical with the entire system. Eq. 1 or its equivalent has been derived repeatedly'-7 and an analogous equation, known as Rayleigh's equation, has been used for distillation. The assumptions on which Eq. 1 is based do not include an infinitely fast cooling rate as sometimes stated. In fact, Olsen and Hultgren %ave shown by experiment that very high solidification rates suppress coring, presumably by preventing diffusion in the liquid and by the effect undercooling has on the composition of the nucleus. Coring thus occurs at rates of cooling which are too fast for a close approach to equilibrium in the solid and too slow to suppress diffusion in the liquid and to cause marked undercooling. If the liquidus and solidus approximate straight lines, Eq. 1 simplifies to The fraction of liquid present at any temperature during nonequilibrium solidification can be calculated from Eqs. 1 or 2. By the lever relation it is

Jan 1, 1955

By Otto H. Henry, J. J. Cordiano

Though powder metallurgy is one of the oldest of metallurgical processes, it is in its infancy as a branch of the modern field of metallurgy. As early as 3000 B.C., the ancients produced implements and weapons of iron by reducing iron ore in a charcoal fire and forging the resultant sponge while still hot into the desired shape. Melting and casting soon superseded the powder metallurgy practice, and it was not until the turn of the twentieth century that powder metallurgy was applied to the commercial manufacture of tungsten lamp filaments. From this beginning, the use of the powder metallurgy process spread" to the manufacture of porous oil-impregnated bearings, cemented carbide tools, contact points, diamond grinding wheels, clutch facings, starter brushes, resin-bonded radio cores, magnets, metallic filters, and other parts. More recently, and particularly during the present war, there has been a definite trend toward the manufacture of machine parts by this process in competition with the more conventional fabricating methods. Notwithstanding these many developments, scientific progress has been slow. While many articles on powder metallurgy have appeared in the press and various publications, there have been too few contributions to our technical societies, with the result that there is a dearth of the type of information necessary for the full development of this science. It is of primary importance that the results of research and development be freely disseminated if powder metallurgy is to realize its fullest potentialities. Purpose of Investigation Excluding the refractory metal field, all commercial powder metallurgical products made by a cold compressing and sintering operation contain voids. These voids can be substantially eliminated by subsequent severe working and heat-treatment, but ' such practice has not proved economical in most applications. By applying heat during the compressing operation, plastic deformation of the powder particles is substantially increased, and the resultant compact or briquette is practically free of voids. However, hot-pressing has many attendant problems, which at present preclude its use in the manufacture of precision parts. The more important of these are to devise: 1. A die steel capable of withstanding high pressures at elevated temperatures. 2. A high-temperature lubricant capable of preventing excessive die wear and welding of the compact to the die walls. 3. A method of retaining a neutral or reducing atmosphere in the compacting zone of the die assembly. 4. A means of ejecting the hot-pressed specimen into a neutral atmosphere until reasonably cold.

Jan 1, 1946

By M. T. Halbouty

The Laredo oil district, South Texas, includes an area of approximately 200 miles long north and south and 75 miles wide, embracing the following counties: Starr, Zapata, Jim Hogg, Webb, Duval and McMullen. The area is relatively old in respect to the production of oil, as the first oil was discovered and produced in the Piedra Pintas field in Duval County on Sept. 10, 1905. Since that date, continuous new discoveries have contributed to the development of this district until, at the present time, it is one of the important oil-producing and gas-producing areas in the world. The year 1937 also had its share of new discoveries in the district, including not only new oil fields but also new sands in already producing pools and important extensions to existing sands and fields. Among the most important field discoveries, by counties, are: Duval County..... Benavides, Sweden, Thomas-Lockhart, Labbe and Lundell fields Jim Hogg County.. Las Animas field McMullen County. Ezzell field Starr County...... El Tanque field Webb County..... Killam and Oilton fields Of these, Benavides, Oilton, Killam and Ezzell have so far proved themselves most important; the Benavides field, Duval County, showing by far the most activity. For the year 1937, therc were 283 wildcat tests drilled in this district, of which 35 were oil producers, 20 completed as gas wells and 228 abandoned as dry holes. Duval County, as usual, received the greatest amount of wildcat drilling, having 21 oil wells, 5 gas wells and 63 dry holes completed during the year for a total of 89 tests. Next came Webb County with 4 oil wells, 4 gas wells and 53 dry holes for a total of 61 tests.The Laredo oil district, South Texas, includes an area of approximately 200 miles long north and south and 75 miles wide, embracing the following counties: Starr, Zapata, Jim Hogg, Webb, Duval and McMullen. The area is relatively old in respect to the production of oil, as the first oil was discovered and produced in the Piedra Pintas field in Duval County on Sept. 10, 1905. Since that date, continuous new discoveries have contributed to the development of this district until, at the present time, it is one of the important oil-producing and gas-producing areas in the world. The year 1937 also had its share of new discoveries in the district, including not only new oil fields but also new sands in already producing pools and important extensions to existing sands and fields. Among the most important field discoveries, by counties, are: Duval County..... Benavides, Sweden, Thomas-Lockhart, Labbe and Lundell fields Jim Hogg County.. Las Animas field McMullen County. Ezzell field Starr County...... El Tanque field Webb County..... Killam and Oilton fields Of these, Benavides, Oilton, Killam and Ezzell have so far proved themselves most important; the Benavides field, Duval County, showing by far the most activity. For the year 1937, therc were 283 wildcat tests drilled in this district, of which 35 were oil producers, 20 completed as gas wells and 228 abandoned as dry holes. Duval County, as usual, received the greatest amount of wildcat drilling, having 21 oil wells, 5 gas wells and 63 dry holes completed during the year for a total of 89 tests. Next came Webb County with 4 oil wells, 4 gas wells and 53 dry holes for a total of 61 tests.

Jan 1, 1938

By Stanley Lefond

Industrial Minerals, often called the Cinderella Minerals or the Building Blocks of industry continued their growth patterns through 1973, although profits were slightly lower due to the cost-price squeeze. Most of the individual reports which follow indicate growth rates of 3-15%. Surprisingly such commodities as sulfur held firm in spite of the over supply in the Canadian gas fields; cement was in short supply while the asbestos industry reported a worldwide shortage of group 4 and 5 fibers. Talc and perlite production set new records. In synopsis, 1973 was a productive year for industrial minerals. However 1974 onward appears to be one of contradiction. The unsettled conditions of world economics, the energy shortage, compounded by the Arabs oil embargo have created great problems for all industries. The high energy consuming segments of the Industrial Minerals field will be under intense pressures. On the other hand limestone, lime and perhaps trona, nahcolite might be consumed in ever increasing tonnages in SO2 removal systems connected with smelters and coal-fired power stations. The effects of the proposed changes in the staking, claiming and exploitation of federal lands by the BLM may also have serious repercussions not only to the industrial minerals field but to the entire mining industry. 1974-1975 will certainly be ear-marked as a year of frustrations and difficult decisions.

Jan 2, 1974

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

By Robert B. Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 5th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 4th edition (1975) of Industrial Minerals and Rocks will clearly demonstate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Review. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. The Industrial Minerals Directory 1977, 1st ed., Metal Bulletin Books, Ltd., London, provides addresses of organizations in the field. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 4th edition of Industrial Minerals and Rocks. Most of these are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 18th annual meeting in 1982, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the US Geological Survey and the US Bureau of Mines. The two agencies publish many reports and maps on a variety of geological and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications: New Publications of the Geological Survey, US Geological Survey, 329 National Center, Reston, VA 22092 and New Publications-Bureau of Mines, Publications Distribution Branch, US Bureau of Mines, 4800 Forbes Ave., Pittsburgh, PA 15213. The US Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, 1970, and 1975. Four major series of publications by the Bureau are Information Circulars, Reports of Investigations, Mineral Trade Notes, and Minerals and Materials. The last two are particularly good for news of foreign developments. The Bureau of Mines Employee Directory, available at all USBM offices, lists addresses and telephone numbers for all offices as well as same for all commodity and area specialists.

Jan 1, 1983

By Floyd E. Bliven

A century ago, Thomas Carlyle sketched the Emblem of the Wasting Candle in one of his papers. "Terar Dum Prosim" he wrote under the candle-" May I be wasted so that I be of use." The application of his reasoning is an excellent guide for a discussion of the scrap problems of today. The General Electric Co. has addressed itself to the need of proper and careful preparation of scrap metals for many years. A supervisor of salvage directs this work in each of the works. Generally he is an engineer and has had broad factory training. He gives general direction to the collection, preparation and disposition of scrap materials. He operates the extensive facilities which each works has provided for the centralization and control of scrap accumulations, and also initiates studies leading to the reduction of scrap accruing from machining and assembly operations. r We recognize that each industry, each factory, each locality faces a different set of conditions. Irrespective of size, in a plant employing 20 men or a large works with 15,00 employees-certain fundamental principles can be applied for organization and the collection of scrap. The manufacture of electrical apparatus is a highly complicated intricate business. In one area we make electronic tube and adjacent buildings house the manufacture of steam turbines. Both are instruments for power-different in size and in many cases serving different fields of application. Unlike the great industries that build automobiles, trucks, or engines where repetitive operations, once solved, set the stage, electrical manufacturers&apos; plants are large jobbing shops. Therefore, we must carefully plan every step in handling the scrap that "in so wasting to produce the finished motor or locomotive-we can return this product to reprocessing and ultimate use." ESSENTIALS FOR SALVAGE EFFICIENCY The essential steps for an efficient salvage department are: I. Selection of Personnel.-An able foreman would be a man of broad experience and understanding-one who commands the respect of the entire foreman group as well as that of his own men. In the interest of clean scrap, it is necessary to acquaint the foremen in the separate manufacturing units with the need of careful segregation in the shop and the best methods of obtaining it. At least 40 per cent contact time should be devoted for this purpose. 2. The physical equipment of the salvage department should be devised and selected to handle complete, at one point, all scrap operations. Bulky materials as produced by some large shops can be economically placed in salable shape at the divisional point. Because salvage

Jan 1, 1943

By W. A. Dickinson, H. F. Hendershot

THIS paper is a brief discussion of the past and present methods employed by the Huntington Works of The International Nickel Co., Inc., in the production of nickel and high nickel alloy seamless tubing. The various operations for both hot and cold processing will be considered in their natural sequence, together with the processing characteristics of the high nickel alloys and some descriptions of the equipment used. The tools and lubricants currently in use will be described. This discussion will relate primarily to nickel, Monel,† and Inconel,† since these are the most common of the many alloys processed into tubing at the Huntington Works. The nominal compositions of the materials are shown in Table I. CONVERSION FROM SOLID BILLETS TO TUBE SHELLS History The commercial production of seamless nickel and high nickel alloy tube shells is a comparatively recent development, the first nickel shells having been produced in 1922, Monel in 1930, and Inconel in 1931 on rotary-type piercing mills. Rolled or forged billets, ranging from 3 ½ - to 7 ½ in. diam, were pierced to produce shells ranging&apos; in size from 4 3/8 in. OD X 0.180 in. wall to 8 3/8 in. OD X 1.0 in. wall. After piercing, the shells. were further processed by hot rolling, reeling, and sizing. Subsequent to these operations the shells were either supplied to the trade as "hot finished" tubes, or were processed by cold drawing to smaller sizes at the Huntington Works of the International Nickel Co. The extrusion of nickel and high nickel alloys also may be classed as a relative newcomer to the field of hot-forming methods, for it was not until 1928 that the commercial extrusion of these alloys was begun on a 600 long ton vertical extrusion press installed at Zenith Works of Henry Wiggin and Co., Ltd., Glasgow, Scotland. This press did considerable pioneer work and the results were so favorable that in 1937 a -2200 long ton horizontal press was installed. The quality of the inside surface of the tubing produced on this press was superior to that produced by piercing on a rotary-type mill and, as a result of this experience, a 4000 ton horizontal extrusion press was installed at the Huntington Works in 1943. Billet Preparation The first step in the extrusion, process is the selection of ingots with good hot malleability, as indicated by the test described by Martin and Bieber.1 Ingots then are forged into rough rounds which are machined to the desired billet diameter on a "bar peeler." This machine consists of a rotary head which carries the cutting tools and is driven by a 200 hp, dc motor. The feed mechanism consists of hydraulically driven input and output carriages on the respective sides of the cutter head. The diameter of the forgings used and the machined size or "billet diameter" that corresponds to the four different sizes of

Jan 1, 1951

By E. C. Truesdale

IN recent years various problems in connection with research work on the preparation and properties of zinc-base alloys have required reliable information concerning the constitution of the zinc-rich portion of the iron-zinc equilibrium diagram. On numerous occasions rather positive indications were obtained that, for example, the solubility of iron in zinc was incorrectly represented on the current equilibrium diagrams. A careful study of all the available literature relating to the iron-zinc system led to the conclusion that much of the early work was unsatisfactory as measured by present standards of experimental accuracy, and as a result it was decided to redetermine the location of the liquidus curve and of adjacent portions of the diagram. Part I of this paper comprises a description of the experimental methods and a summary of the results by means of which the zinc-rich end of the iron-zinc diagram has been revised in the following ways: 1. Measurements of the solubility of iron in liquid zinc by several different sampling methods, leading to a relocation of the liquidus curve. 2. Microscopic, conductivity, and X-ray studies of the solid solubility of iron in zinc, which, together with thermal analyses, have resulted in new values for the solid solubility and the eutectic temperature and composition. 3. Heating and cooling curves, obtained by a refined differential method, leading to new locations for the two peritectic horizontals. In Part II of the paper the attempt is made to review all of the pub-lished work having a bearing on the constitution of the iron-zinc system, and to correlate the present results, and some recently published data

Jan 1, 1935

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

Hydrogen forms a beta-stabilized system with titanium, with a beta eutectoid at about 300°C and 44 atomic pct H2. &apos;The solid solubility of hydrogen in alpha decreases from about 8 to about 0.1 atomic pct from 300°C to room temperature. Hydrogen has little effect on tensile properties, but decreases notch-bar toughness to a large degree. This latter effect appears to be the result of increased notch sensitivity. PRIOR to this investigation, only a small amount of information was available on the effect of hydrogen on the mechanical properties of titanium. The effects of the other interstitially soluble elements, carbon, oxygen, and nitrogen, had received detailed study. Jaffee and Campbell1 indicated that hydrogen up to 1 atomic pct did not affect tensile properties deleteriously. Pitler&apos; indicated that 1 atomic pct H, in titanium reduced the impact strength appreciably, but his alloys contained appreciable amounts of oxygen, and it was difficult to attribute the embrittlement entirely to hydrogen. The high temperature portion of the equilibrium diagram for the Ti-H system was established by McQuillan," and his data generally corresponded with the results of Kirschfeld and Sieverts," Gibb and Kruschwitz," Bevington, Martin, and Mathews," and other investigators. The lower concentration limit of the hydride phase varied considerably among investigators, and Gibb and Kruschwitz9 ad shown that small amounts of contaminants in either titanium or hydrogen caused considerable variation in this lower limit. In view of this pronounced effect of contaminants, the extrapolated value of McQuillan&apos;s, about 48 atomic pct at the 325°C eutectoid, appeared the most reasonable. McQuillan&apos;s lowest experimental value was 54 atomic pct at a temperature of 450 °C. The density of titanium had been shown to decrease with increasing hydrogen content, but discrepancies were noted among the various investigations. The best values indicated that the density was decreased from 4.56 grams per cc at 0.27 atomic pctl to 3.84 grams per cc at 61.3 atomic pct? This investigation was conducted to determine the effects of hydrogen on a titanium, both in high purity and commercially pure metals, and on high purity a titanium alloys. Material and Fabrication The literature indicated that impurities in either the hydrogen or the titanium must be kept to a minimum. For this reason, the initial studies were made with high purity iodide-refined titanium. The vendor&apos;s analysis of the iodide titanium and the hydrogen content of the as-fabricated Y4 in. diameter rods are shown in Table I. Two 1 lb ingots were prepared by arc melting under argon in a water-cooled crucible, using a water,cooled tungsten electrode. This equipment has been described.&apos; As-cast Brine11 hardness numbers of 88 and 58 for these ingots were low enough to insure that the high purity of the metal was maintained during arc melting. The ingots were hot forged to % in. diameter rods at 800°C, cleaned by grit blasting, and then cold swaged to Yz in. diameter rods. The rod was then air annealed at 725 "C, ground to remove scale, and cold swaged to Y4 in. diameter (75 pct reduction in area). The material was then annealed for 1 hr in argon at 800°C to develop an equiaxed a grain size of about 0.05 mm. Micro tensile specimens and microimpact specimens were machined from this rod prior to treatment in the Sieverts-type absorption apparatus. Two lots of commercially pure RC-55 titanium were also used in this investigation to determine the effects of hydrogen and the normal impurities on mechanical properties. The commercially pure RC-55 alloy was obtained in the form of % in. diameter rod. The analysis of this material is also given in Table I. The % in. diameter rods were hot swaged

Jan 1, 1955