Search Documents

By Willis Burns

I. INTRODUCTION. These notes are submitted, not as a discussion of the modern practice of electrolytic-copper refining, but as the record of a refinery that was among the pioneers in the field and that is to-day, and has been for 17 years, operating under conditions not to be found in any similar plant in the country. I refer to the current density, which is at least 60 per cent. higher than that regularly employed elsewhere, and to the fact that the anodes treated are the direct product of the converter rather than of the reverberatory furnace. The writer has no knowledge of any other refinery treating anodes of this character.

Jan 8, 1913

By C. D. King

THE advances in basic open-hearth practice which have occurred during the past decade, have been principally in the direction of the physical development of larger units, decreased fuel consumption and increased length of furnace campaigns. However gratifying the economies which have resulted from these improvements are, it must be granted that like advances in chemical, physical-chemical and metallurgical knowledge pertaining to open-hearth practice would have added greatly to these already attained reductions in costs and it is the purpose of this paper to stimulate the discussion and study of these phases of cooperation and their relation to ingot yields. DEFINITION AND CALCULATION OF LOSSES In discussing basic open-hearth yields, the writer refers to the ingot yields obtained in the process of converting pig iron, scrap and ore to steel. In this conversion some scrap is produced. The difference between the total weight of ingots and scrap produced and the original metallic charge, constitutes the loss. Basic open-hearth yields vary considerably, and while some of the divergencies can be explained metal-lurgically because of differences in slag analysis, proportion of pig charges, and character of steel made, there often remain differences that apparently do not readily disclose themselves. In reconciling yields by the usual accepted methods of calculation, one is often forced to evaluate large losses as "unaccounted for." Such a system is prone to accept these large losses as inherent to the operation and not susceptible of appraisement and correction. It is obvious that if the ingot yield, plus the scrap recovered subtracted from 100 per cent. determines the loss, a drop in yield may increase the loss or the scrap, and both contribute to a monetary loss. To be sure, one can subdivide these unaccounted for losses into various components, such as metallics in slag, free Fe in slag, spillage, etc., and thereby reduce the amount of losses considered as "unaccounted for." If empirical methods could indicate with some degree of accuracy all losses, however slight, the undetermined losses become appreciably smaller and resultant calculations will check actual

Jan 1, 1929

Discussion of the paper of Archer E. Wheeler and Milo W. Krejci, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1831 to 1880. BRADLEY STOUGHTON, New York, N. Y.:-I would like to ask Mr. Krejci whether they have tried mixing coke dust with the lime in those converters and, if so, if any advantage has been found. It has been a very great advantage in the steel converters where coke dust has been mixed with the lime near the tuyeres. Of course the agent that causes the corrosion at that point is oxide of iron, and coke seems to prevent the formation of the oxide of iron and so protect the tuyeres. It would be interesting to know if it had the same effect in the copper converters. MILO W. KREJCI:-We have never tried it here. At Anaconda the tuyere section was formerly put in by mixing magnesite with tar and ramming that into the tuyere section, but they have abandoned that. Might I ask how you would apply the coke dust? How get it into the tuyere section ? How hold it there ? BRADLEY STOUGHTON :-The coke dust is mixed with silica and clay and then rammed in and burned. I suppose in your converters it would be mixed with the magnetite or magnesite and then agglomerated with the material in place. MILO W. KREJCI:-We never tried it here. PROF. JOSEPH W. RICHARDS, South Bethlehem, Pa.:-I would like to ask how thick this deposit of magnetite is on the lining. How thick a layer would be practical ? MILO W. KREJCI:-About 21 in. would be sufficient. SOLOMON LE FEVRE, Mineville, N. Y.:-I was interested to hear of the use of magnetite in connection with the copper smelter. I am interested in the mining of magnetite, but was not aware that it had been used at all' by the copper metallurgists.

Jan 11, 1913

By J. T. Norton

As cold working is an important feature in a great many of the fabricating processes now applied, this paper presents some ideas of the nature and results of the plastic deformation produced in this operation. The art of manufacturing metal for practical uses is very old and has undergone very great development. The science of metals has also developed very rapidly recently and the various processes to which ,metals are submitted are much better understood now than they were even a short time ago. All the knowledge that can be obtained on this subject is useful because it promotes efficiency in converting metal into finished articles. ATOMIC ARRANGEMENT IN CRYSTALS In the solid state all metals are crystalline. The atoms are arranged in, a definite symmetrical configuration, which is repeated at regular intervals, and thereby defines what we may term a lattice. Presumably . the atoms exist as positive ions. The dissociated electrons place themselves between groups of positive ions, and thus define a second lattice, an "electron lattice." From such a point of view, the crystalline forces which hold a metal together are the electrostatic attractions between positive ions and negative electrons. The particular type of lattice into which a metal crystallizes depends on the number of these lattice electrons given up by each atom, and is thus connected very closely with the chemical valence of the metal.

Jan 12, 1926

By Robert Mehl

PART I. ORIENTATION RELATIONSHIPS IN OXIDE LAYERS Oriented overgrowths and intergrowths among both metallic and nonmetallic substances have been recognized and studied for well over a century. The work of Widmanstätten in 1808 on the geometrical struc-ture in meteorites, a structure known by his name, demonstrated that oriented intergrowths can occur in purely metallic systems. This fact led to much of the early microscopic study of alloys, contributing greatly to the advance of physical metallurgy. The problem has been attacked again in recent years in a comprehensive fashion, with the object of dis-covering what atomic movements may occur during phase changes in alloy systems. Much of this work has appeared in the A.I.M.E. TRANS-ACTIONS in a series of papers published by Mehl and coworkers beginning in 19311. Although many aspects of this general problem remain unsolved, it may be said that the orientation of a new phase forming by precipitation from solid solution or by transformation invariably bears, a unique relationship to the orientation of the phase from which it formed, and that similarity in atomic patterns on atomic planes in the two phases play an important part in determining the orientation relationship. Analogous orientation relationships exist in oriented intergrowths in nonmetallic systems-mineral or inorganic. In 1827 Haidinger2 dis-covered natural intergrowths of hematite and magnetite, and demon-strated that the rough form of the magnetite octahedrons was delineated by small crystals of hematite, of which the basal (00.1) planes lay parallel to the octahedral cleavage planes of the magnetite. The description of this orientation relationship was later completed by von Rath3, who showed that the edge (00-1):(10-1) in hematite lies normal to the [111]

Jan 1, 1937

By E. S. Grumell

The correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbreviations will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution. Section 1.—Cost It has often been stated that the cost of sampling should bear some relationship to the value of the product, and since coal is a relatively cheap raw material it would be a major error to specify, for ordinary commercial purposes, elaborate and costly methods of sampling which nobody would adopt. Specifications must be of such a nature that they will be used. We believe that one of the achievements of the last 10 years has been to reduce the cost of sampling. There is, however, another point to be considered; via., that the cost of sampling should bear some relationship to the value of the investigation. Correct sampling is a cog (possibly a small one) in the wheel

Jan 1, 1940

By Nicholas J. Grant, Noboru Komatsu

Metallographic and X-ray studies were made of oxide dispersion strengthened Cu-12 vol pet SiO2 and Cu-3.5 vol pet Al2O3 alloys following time exposures at temperatures approaching the melting. point of the matrix metal. Changes in hardness, oxide particle size and crystal structure were studied to determine the time-temperature stability of these alloys. An interpretation of the mechanism of oxide agglomeration is proposed. One of the most striking features of dispersion strengthened metal-metal oxide alloys is their stability at elevated temperatures, both with respect to recrystallization and maintenance of mechanical properties after exposure at high temperatures. A small amount of work has been done on the re-crystallization phenomenon in dispersion hardened metal-metal oxide alloys'l and several theoretical treatments have been advanced regarding the stability of these alloys by Lenel and Ansell,8 and by Grant and his co-workers.9, 10 This paper reports on metallographic and X-ray studies following various heat treatments of Cu-AI2D3 and Cu-SiO2 alloys at elevated temperatures and the effect of subsequent cold work on the recrystallizalion temperature. An interpretation of the recrystallization behavior of this type of alloy, based on the decomposition and agglomeration of oxides, is proposed. EXPERIMENTAL PROCEDURE Cast ingot bars of copper-1.59 pet Si and Cu-0.77 pet Al, 7/8 in in diam, were annealed in argon for 80 hr at 1000CC for homogenization. The homogenized rods were machined into fine chips and ball milled. Milled particles in the range minus 20 to plus 60 mesh were separated for internal oxidation. The internal oxidation was accomplished by the same method used by Preston and Grant,9 except that the oxidalion temperature for the Cu-Si alloy was 750°C, and for the Cu-A1 alloy was 800°C. These powders were then hydrogen-reduced at 450°C, compacted in a copper container, evacuated at room temperature to 0.04 µ, and sealed for extrusion. They were extruded at 1400°F (760°C) with a ram speed of 55 in. per min for an extrusion ratio of 15.6 to 1 to give a rod 0.38 in. diam by about 3 ft long.

Jan 1, 1962

By Francis H. Crockard

During the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of streamlined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements. In addition to questions of quality, the subject of cost has greatly altered the southern furnaceman's viewpoint on many things. Formerly we had low-grade but cheap raw materials, but recent developments, such as greatly increased labor rates, have raised the cost of the same

Jan 1, 1936

By R. W. Hyde, B. S. Old, S. E. Eaton

One of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects On both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steel-making. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2} The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2.3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States. It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaS04). The sulphur is subsequently found in the coke in combination with carbonaceous material of is composition and as calcium and iron sulphides' In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke. Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two ""jar forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high .in total sulphur, would yield coke of fairly low sulphur content. Using the new

Jan 1, 1949

By Y. C. Liu, R. H. Richman

From rolling textures of polycrystalline AgCl determined as a function of temperature, changes in the amounts of the individual textural components are correlated with temperature-dependent changes in glide geometry. The preferred orientations are influenced by the slip behavior as follows: 1) pencil glide, characterized by (110) slip directions and a greater participation in the deformation the higher the temperature, leads to a(012) fiber texture; 2) low-temperature deformation, primarily on (110) (110) systems, generates the {237}-(11, 9, 7) component; and 3) slip on {111}(110), comprising a significant portion of the room-temperature deformation, generates the {135}(211) and {110}(112) components. Typical re crystallization textures are also presented and briefly discussed. SPECIFIC relations between flow mechanisms in crystals and the individual orientations or components in deformation textures are necessary for a thorough understanding of the origin of such textures. Within each ordinary class of crystal struc- tures there is insufficient variety in the observed preferred orientations to permit direct and unambiguous correlation between flow mechanism and texture. A second approach to this problem is the correlation of textural changes with some known variation in glide geometry within one substance,1 In this paper, the latter approach is applied directly to a material in which there are distinct changes in the character of glide with changes in temperature. Silver chloride, although a nonmetal, is reported to exhibit slip,2,3 fiber textures,4 and rolling textures5,6 crystallographically similar to those of the well-studied fcc metals;7,8 in addition, there is a marked temperature sensitivity of the glide planes upon which flow occurs.3 Previous investigations of textures in AgCl unfortunately did not employ methods sufficiently sensitive to define possibly important minor components in the texture, nor did they utilize the temperature dependence of the glide systems. Thus, in order to clarify the effects of changes in slip mechanism, this paper reports a survey, using semiquantitative methods, of preferred orientations in rolled AgC1. Inasmuch as the influence of prior deformation texture upon preferred orientations after annealing is also of interest, some representative annealing textures are presented.

Jan 1, 1965

By Alfred Boyles

THE experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of funda-mental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic and in others i produced al marked changes in the size of the graphite flakes. These effects seemed to be III sulphur and manganese present in the material studied. Iron-carbon- respond silicon alloys did same manner as mg cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of FIG. 1.-APPARATUS FOR MELTING UNDER PRESSURE. silicon. The present paper is con- A, inlet for gas. cerned with alloys of lower silicon B, outlet for evacuation. content and describes the structural C, power lead. D thermocouple changes produced by melting in E, plug for access to furnace. various atmospheres at pressures F, crucible. ranging from a partial vacuum up to 300 lb. per sq. inch.

Jan 1, 1939

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the silicides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. MANGANESE AS A SCAVENGER Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

Jan 1, 1928

By Thomas Egleston

The ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, however, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattlesnake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

By R. T. Gallagher, C. G. Brennecke

This paper is the result of a research program entered into cooperatively by the General Reinsurance Corporation and Lehigh University in January 1944. The research program was instituted to find a more positive method to determine the presence of hazardous roof conditions in , mining operations. The co-authors, together with Mr. R. D. Currie, Engineer for the General Reinsurance Corporation, started working on the project in January 1944, first undertaking a library search; second, a preliminary study based on some existing equipment; third, the design of new and more suitable equipment; and finally, the field testing of equipment and methods. Purpose Any study of the accident statistics of mining operations will disclose the rather startling fact that approximately 50 to 60 per cent of all fatal underground accidents in the anthracite and bituminous mines are caused by falls of roof and coal, the metal and nonmetal mines showing only a slightly smaller percentage. Advancements in safety engineering have produced definite results in the decrease of accidents due to blasting, haulage, electricity, and explosions but no such decrease is shown in those caused by falls of roof, coal, or ore. Table Il,2 is a compilation of statistics as published by the United States Bureau of Mines, showing the percentages of fatal accidents caused

Jan 1, 1947

By Arthur Taggart

FLOTATION of ores is a practical utilization of the energy that resides in the surfaces of solids and liquids. The best known manifestation of this energy is called surface tension; an equally important, though less apparent, phenomenon is adsorption. This paper reviews some of the recent investigations of these phenomena, and gives the results of certain experiments performed by the authors. Surface tension is a manifestation of energy having its seat at the bounding surface between the adjacent phases of a multiphase system. Thus, at the interface between a liquid and a gas, or between two immiscible liquids, or between a solid and a gas or a liquid, there are forces capable of doing work, their magnitude depending on the nature of the adjacent phases and the extent of the bounding area. These surface forces are inappreciable when the ratio of surface to volume of the adjacent phases is small, but they become powerful when this ratio becomes large, as it does when one of the phases is highly dispersed. Froth flotation, which consists in buoying solids heavier than water to the surface of water by means of gas bubbles, utilizes the force of surface tension to attach the solid particles to the gas bubbles and again to maintain the floating mass of bubbles as a more or less persistent froth at the surface of a pulp for a sufficiently long time to allow its removal. It follows from the second law of thermodynamics that the potential energy of a system in equilibrium is a minimum. Therefore a multiphase system, tending toward equilibrium, will arrange itself in such a way that the total energy of the interfaces will be the least possible. This end can be accomplished in two ways: by a change in shape that will reduce the interfacial area; by a change in the nature of the surface layer in

Jan 8, 1922

By Arthur B. Cummins

Mineral fillers are employed in United States industries to the extent of more than seven million tons annually, valued in excess of a hundred million dollars. This substantial usage involves a wide variety of mineral materials. To this may be added products manufactured from minerals, such as carbon black, portland cement, lime or chemically precipitated calcium carbonates, which would add substantially to the total. The purposes for which fillers are used differ considerably. Minerals used as fillers are mostly silicates, silicas, and carbonates as referred to hereinafter. The term "mineral filler" has various meanings in mineral technology and in the arts. Fillers are comparatively inert and their action is mainly physical. Materials that are employed primarily for chemical reactivity, or for pigment or abrasive functions ordinarily would not be considered to be fillers when used for these purposes. Nearly all filler usages are based on advantages which are gained by desired modification of composition properties or by improvements in processing. A simple definition for a filler is an inert material that is included in a composition for some useful purpose. This definition may be amplified or made more specific for each of the filler usages, the major ones of which are: paints, paper, plastics, rubber, bituminous compositions, pesticides and fertilizers. There are in addition a whole host of minor usages. Powdered minerals when employed as components in paints, varnishes and lacquers are considered as extender pigments or low refractive index pigments. In paper, the term loading material as well as filler is used; in pesticides, the terms diluents and carriers connote different functions. For bituminous compositions, rubber and plastics, the usage of the simple word "filler" is more usual, but the designation loading material is sometimes used. Minerals Used as Fillers Most of the industrial minerals, and many rock powders are employed to some extent for different filler uses. These usages vary from year to year depending on availabilities, costs, technologic trends and advancements. For the major applications, however, and for the more particular requirements at any given period, there are general trends which favor a more or less restricted group of filler products for each of the major consumer fields. This selection of materials is determined by the characteristics of the individual filler products, their effectiveness in fulfilling the primary function or functions for which they may be employed, and the cost after incorporation in the finished product. The mineral-bearing materials of major importance as fillers are: limestones, clays of several types, talc, pyrophyllite, mica, barite, diatomite, crystalline silicas, asbestos, slate and other rock dusts. Others of secondary importance include: gypsum, vermiculite, phosphate rock, perlite, and pulverized wastes, such as slag and fly ash. A considerable number of other minerals are used to lesser extent. Among these minor mineral materials are: feldspar, pumicite, wollastonite,18 tripoli, nepheline syenite,6 coal, altered volcanic rock and others.2 Indeed, most mineral materials, when reduced to fine particle size may have some potential usage as fillers, depending on their properties, availability and price. On the other hand, the more exacting filler requirements

Jan 1, 1960

By B. A. Rogers

The etching effect that is produced on a piece of polished iron or steel when it is heated in hydrogen or in a vacuum seems to have been observed first by Osmond,' who believed that he could distinguish four systems of grain boundaries on a piece of steel which had been heated in hydrogen. In a number of other investigations, samples of pure iron were found, after heating, to have complex networks in which two or three systems of grain boundaries could be detected. It was further noticed that samples that had been polished plane before being placed in the furnace were, after treatment, roughened and undulating over their entire surfaces. From a comparison of the temperature of heat treatment with that of the A3 transformation, it was concluded that the changed appearance of the samples was definitely related to the latter phenomenon. Certain other deductions were made but these are not of importance here and only observations on the appearance of the samples will be reviewed. Ewen2 heated a strip of polished iron in a vacuum in such a way that one end was maintained at a temperature of 1000" C. and the other at 580" C. On the cooler end there was outlined a simple polyhedral network, and at the hotter there appeared the complex systern of lines ant the undulating surface characteristic of iron which has passed through the A3 transformation. He found that in going from the cooler toward thc hotter end the sample maintained much the same character of surface up to the beginning of the transformed area, but that near this region doublc grain boundaries were of frequent occurrence. Rawdon and Scott concluded that the simple type of network brought out by heating a sample of pure iron in a vacuum was of the same type as that developec by ordinary etching methods. They also confirmed the observations of

Jan 1, 1929

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger; because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth's gravitational field. which furnishes us

Jan 1, 1927

By J. B. Mudd

Introduction It is difficult to think of any activity on which mankind has been more dependent than mining, and certainly there is much evidence in almost every part of the world of old workings that clearly demonstrate that man from earliest times has dug and toiled to take from the earth precious stones, metals and materials that from time to time have been essential or of value to him. In step with social development and industrial and technological advances the tempo of mining activity, regulated only by the laws of supply and demand, has quickened and in this century has accelerated rapidly in keeping with its dramatic development. Indeed, the rate of change of events has been such that if it were to continue to accelerate as fast as it has over the past decade there is reason to wonder how the insatiable demands for metals and minerals are to be met in the years that lie ahead. Shallow mines containing high-grade ore deposits either have been or are being rapidly mined out and their place can only be taken in general by ore lying at greater depth, or by ore of low grade, situated for the most part in remote and in underdeveloped areas. The cost of exploration and development is rising at an alarming rate, with the result that the expenditure now required to bring a mine to production far exceeds anything previously contemplated. It is estimated that the total capital required to maintain existing operations and develop new ones during the next 5 years will be of the order of $50,000 million and of this, new capital to bring new mines to production will be of the order of $3,000 million. Today no single mining finance company can, from its own resources, find all the money for a major mining development, and as a consequence there has been a strong trend toward joint ventures and to the formation of multinational consortiums. International lending institutions already play an important part in financing many new mining projects and their participation provides the financial umbrella under which other lenders can invest with greater security. There is little doubt that to finance the costly ventures in the future, governments and international lending agencies, banks and finance

Jan 1, 1971

By Frances Jane Cromwell, D. J. McAdam, G. W. Geil

In a series of papers, the authors and their associates have shown that the technical cohesion limit is affected by the same four factors that affect the flow stress, namely, the stress system, plastic deformation, temperature, and the strain rate.16-28 Moreover, each of these factors affects the technical cohesion limit in the same way that it affects the flow stress,t The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term ilfracture stress' has come into use with the same significance as 'ctechnical cohesion limit," the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. This paper presents the results of an investigation of the flow of notched and unnotched specimens betqrcen yield and fracture, A study has thus been made of the flow and fracture of metals as affected by the stress system, and of the ductility of metals as affected by the stress system throughout plastic deformation. Since two of the principal stresses were equal (S2 = S3), the stress systems can be represented in terms of the radial stress ratio, the ratio of the transverse radial stress s3 to the longitudinal stress S1.* The results of the experiments are represented by a series of their flow-stress curves for each Of the metals investigated, and these diagrams have been used for the development Of Other diagrams Of various types. Ludwik was the first to suggest that fracture occurs when the flow stress becomes equal to a technical cohesion limit. Although Ludwik was incorrect in his view that the technical cohesion limit depends only on the amount of plastic deformation and not On the stress system, he was 'Orrect in his view that the flow-stress curve for any stress system terminates at a point representing a technical cohesion limit. The authors have seen some recent references to assertions by other investigators that a point representing the fracture stress need not be on the flow-stress curve. The Ludwik principle, however, "auld Seem to be axiomatic, provided that the flow Stress and fracture stress are properly defined and that the fracture stress is properly determined. Disregard Of this principle has led to some untenable theories Of criteria for fracture. When a metal is very ductile, the conventional method of determining the ductility and fracture stress by dividing the breaking load by the sectional area after fracture, generally gives values that are much too high. With some metals and in some conditions, the fracture stress thus determined may be two or more times the

Jan 1, 1949