Search Documents

By Gilbert Francklyn

The requirements of coals for the manufacture of coal gas, water gas and producer gas will be considered sparately and a short description of each gasmaking process will be given. In this report the term "gas coal" is confined to coals suitable for the manufacture of city gas in horizontal, inclined or vertical retorts. The report does not refer to coke-oven practice.' Briefly, the process of manufacture consists of distilling the coal at high temperature in an externally heated retort out of contact with the air. The products of distillation, consisting of gas, tar, ammonia, etc. are collected and purified. The residue consists of coke, which is removed from the retort at the end of the carbonizing period. To supply the heat required in the process, a portion of the coke produced is converted into producer gas, which is burned under the retort settings. Qualities of Gas Coals The chief qualities that coal must possess in order to be classified as a gas coal are as follows: 1. Gas Yield.—The coal must be capable of yielding gas in sufficient volume and of a satisfactory quality. The yield depends considerably upon the temperature of distillation; a higher temperature will give a larger yield of gas, but the qualit,y of gas (now measured by the British thermal units per cubic foot) will be lower, while a lower carbonizing temperature will give less gas of higher heating value. The true measure of the yield is the number of British thermal units produced in the gas from a given quantity of coal. This number is obtained by multiplying the cubic feet of gas from 1 lb. of coal by the British thermal units per cubic foot of gas; it is called B.t.u. feet per pound. It is found that the

Jan 1, 1930

By J. H. Frye, R. M. Treco, J. W. Caum

IT has been suggested that: "Insofar as the hardening due to a solute depends upon the increase of lattice parameter produced by it, it is reasonable to suppose that this hardening might be related to the resistance which the pure solvent would offer to increase in its parameter."' It was further suggested that this hypothesis might be examined by comparing the hardnesses of analogous silver and copper alloys, since the stress necessary to produce a given lattice expansion is quite different in the two metals. Suitable data2,3,4 are now available on these alloys, and we shall proceed to an examination of the hypothesis quoted above. Hardness, Lattice Parameter and Ionic Overlap Increase in ultimate Meyer hardness has been plotted against increase in lattice parameter in Figs. I and 2. It is believed that most of the values are accurate within the limits indicated by the rectangles. These data are also presented in Table I. Ultimate Meyer hardness, P u, is defined by the equation: where L = load, D = diametei of an impression having the same diameter as the testing ball, which in this case is 4 mm. Increase in lattice parameter is defined as the difference between the lattice parameter of the solid solution and that of the pure solvent. The curves in Figs. I and 2 are based on equal solute concentration and an equal degree of plastic deformation pro duced by the testing ball. Hardnesses are corrected to a constant grain size for copper and silver alloys, respectively, and these two grain sizes are approximately equal. Furthermore, all solutes are from the same period of the B subgroup of the periodic table as their solvent. The question arises as to whether Or not lattice parameter is the only factor controlling the hardness of these alloys. There

Jan 1, 1943

By Orson Cutler Shepard, Charles F. Skinner

THE leaching method that was first widely used with the cyanide process consisted of percolation leaching of crushed ore in vats or leaching tanks. It was frequently necessary to separate the sand for cyanide treatment and discard the slimes, because only granular material allows the necessary amount of solution to percolate through it in a reasonable time. Later a slime process consisting of agitation followed by thickening and filtration was developed, and is extensively used to the present day. Even though the agitation-leaching slime process is considered satisfactory, the cost of plant and of operation are both greater than for a percolation-leaching plant of equal capacity. This situation has been recognized in the hydrometallurgical treatment of copper-bearing slimes; and a considerable amount of work has been done at the Southwest Experiment Station of the U. S. Bureau of Mines in an effort to develop a percolation method of treating slimes. Experimental work on the copper-leaching problem was started by H. E. Keyes1, and later tests were made by J. D. Sullivan and A. P. Towne2. The Bureau of Mines work resulted in the development of a process by which slimes were moisture-agglomerated with sand and crushed ore, to form a permeable mass through which solution could be trickled without breaking down the glomerules. The agglomeration trickle-leaching method was developed on a small scale and finally tried out in a 12-ton vat. Successful results were obtained as long as the leach solution was added slowly, so that the agglomerated charge was never flooded. If the leach solution flooded the charge, the glomerules broke down and the charge became impervious. There are two important difficulties in the application of the agglomeration trickle-leaching method to the cyanide process for gold and silver ores:

Jan 1, 1937

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By J. E. Tiffany

FOR blasting in coal mines the U. S. Bureau of Mines recommends that permissible explosives be used exclusively, that these shall be fired electrically, and that where feasible the working place shall be cut or sheared. These recommendations are made to promote safety and prevent mine explosions. Although permissible explosives are not flameless, their lower flame temperature and shorter duration of flame make their use safer than that of non-permissible explosives. Mixtures of air with both methane and bituminous coal dust, which are liable to occur in coal mines, may be ignited by coming in contact with any type of flame or spark of sufficient temperature and duration or by the firing of a blast. In a working place where a blast is to be fired, in addition to the use of permissible explosives, adequate ventilation for the dilution and removal of accumulations or outbursts of flammable gas should be provided. Bituminous coal mines should be rock-dusted as a means of rendering the coal dust harmless. The efficient use of permissible explosives depends upon the proper preparation of the working place, standardized drilling, the strength characteristics of the explosive, and the use of a proper weight of charge. Experienced shotfirers should load, tamp and fire all holes. The major part of the information and data here presented is based on the results of efficiency tests made in large producing mines of Pennsylvania and Illinois. Bureau of Mines Report of Investigations, Serial No. 2697, describes how a standard method of blasting was worked out and put into operation in a mine in southern Illinois.1 This paper contains a description of the methods worked out subsequently in another mine in that district.

Jan 1, 1928

By J. E. Tiffany, S. S. Lubelsky

For blasting in coal mines the U. S. Bureau of Mines recommends that permissible explosives be used exclusively, that these shall be fired electrically, and that where feasible the working place shall be cut or sheared. These recommendations are made to promote safety and prevent mine explosions. Although permissible explosives are not flameless, their lower flame temperature and shorter duration of flanie make their use safer than that of nonpermissible explosives. Mixtures of air with both methane and bituminous coal dust, which are liable to occur in coal mines, may be ignited by coming in contact with any type of flame or spark of sufficient temperature and duration or by the firing of a blast. In a working place where a blast is to be fired, in addition to the use of permissible explosives, adequate ventilation for the dilution and removal of accumulations or outbursts of flammable gas should be provided. Bituminous coal mines should be rock-dusted as a means of rendering the coal dust harmless The efficient use of permissible explosives depends upon the proper preparation of the working place, standardized drilling, the strength characteristics of the explosive, and the use of a proper weight of charge. Experienced shotfirers should load, tamp and fire all holes. The major part of the information and data here presented is based on the results of efficiency tests made in large producing mines of Pennsylvania and Illinois. Bureau of Mines Report of Investigations, Serial No. 2697, describes how a standard method of blasting was worked out and put into operation in a mine in southern Illinois.' This paper contains a description of the methods worked out subsequently in another mine in that district. Descriptions of tests in two Pennsylvania mines are given in Bulletins 11 and 19 of the Carnegie Institute of Technology.2 These tests

Jan 1, 1928

By R. N. Dokken, J. F. Elliott

A high-temperature solution calorimeter was used to measure directly the partial molar heat of mixing of nickel in the Cu-Ni system, 0 to 15 at. pct Ni and 1200°C; of silver in the Cu-Ag system, 0 to 50 at. pct Ag and 1100°C; and of cobalt in the Cu-Co system, 0 to 6 at. pct Co and 1200°C. The heats of fusion of copper and silver were also detervnined directly. The results of these investigations are as follows: Cu-Ni: HM = [2.64 + 0.25Xm JXNiXCy kcal/g-U~OI Cu-Ag: HM =[4.00 + 0.31XAglXAgXCu kcal/g-atom Cu-Co: HF~ = [8- 5X~,]X& kcal/g-atotn Cu, AH, = 3290 * 275 cal/g-atom Ag, AH, = 2890 * 250 cal/g-atom The performance of the calorimeter was enhanced by improving the operational and control procedures, particularly the temperature-wieasuren~ent method and the solute-addition practice. The interpretation of the experimental data was improved by developing machine computational techniques that increased the speed, flexibility, and accuracy of the treatment of the data. THIS paper reports further measurements of the heats of solution of liquid metals with the high-tem- perature solution ca1orimeter.l Measurements were made of the partial molar heats of mixing in the following liquid alloys: Cu-Ni, Cu-Ag, and Cu-Co. In addition the heats of fusion of copper and silver were also determined. The apparatus and the experimental procedure were essentially those of Benz and Elliott.2 Several modifications in the experimental method and the means for interpreting the data were incorporated in this study to improve the results. The operation of the calorimeter and its characteristics will be described only briefly here. The

Jan 1, 1965

By Ernest Robinson

SINCE the early nineties, there has been a persistent belief in some minds that petroleum in commercial quantities exists in Montana. It is, however, only comparatively recently that commercial produc-tion has been secured. . The earliest deep boring in the plains region of Montana was made in what is now Blaine County, in 1890, by the town of Chinook in an effort to secure artesian water. The well reached a depth of 956 ft. without developing an adequate supply of fresh water, but the drillers reported shows of oil and gas. In 1892, the Quartermaster's Depart-ment of the U. S. Army drilled a hole at Fort Assini-boine, northwest of the Bearpaw Mountains, in essentially flat-lying sediments to secure water for the military establishment. This well reached a depth of 1500 ft. and shows of oil and gas were reported. In 1903 and 1904, two wells were drilled within what is now the Glacier National Park in an effort to develop oil production. Shows of oil and gas were encountered at several horizons but no commercial production was brought in. The extraordinary geological conditions in the area where these wells were drilled should be mentioned. The thrusts from the southwest which, in other places along the Rocky Mountain front, resulted in folding, here developed the great Lewis overthrust fault. It is in fact largely to this fault that the magnificent scenery of the Glacier Park is due. A great thickness of Algonkian strata belonging to the Belt series was thrust northeastward over the upper Cretaceous sediments. The derricks under which the wells referred to were drilled were in moun-tains composed of very old rocks but the holes were drilled through Cretaceous sediments.

Jan 7, 1923

By J. L. Stuck

Geological investigation and research have contributed greatly in making industrial minerals the basis of an important industry in the state. North Carolina contains a wide variety of industrial minerals and rock. Mica, feldspar, kaolin, halloysite, talc, pyrophyllite, silli-manite, and spodumene are used to illustrate the progress being made. IN a previous paper1 an attempt was made to indicate the importance of industrial minerals in North Carolina and the wide variety of such materials present. The present paper is concerned with geological investigation and research which have made industrial minerals the basis of an important industry in the state. Geological mapping has gone through three stages in North Carolina during the present century. The first stage is represented by excellent reports of which Corundum and the Peridotites of Western North Carolina,2 Volume I, now a classic, is representative. In this report, a geologic map of the western third of the state is shown on a scale of 10 miles to the inch. The next stage is represented by folios" of the U. S. Geological Survey published between 1902 and 1932. Most of these contained 30 min quadrangle maps on a scale of 2 miles to the inch. The third step is represented by reports prepared during the past 10 years which contain geological maps4 on scales varying from 500 ft to 1 mile to the inch, while many mine maps have been prepared on scales varying from 20 to 150 ft to the inch. As the scale on which geological mapping has been done has decreased, the amount of information secured has increased. Pratt and Lewis did excellent work on the peridotites of western North Carolina, but their maps lacked details. Keith and others added

Jan 1, 1952

By Harry V. Warren

During the past few years the author has had an opportunity to examine a number of base-metal mines in the western United States, France and Spain. Nearly all of these mines produced some silver, and laboratory studies of the relationship between the silver and the various base-metal minerals in the ore have given some interesting and, it is to be hoped, enlightening facts. As this work was undertaken primarily to ascertain the amount of silver chemically associated with, not controlled by, the various base-metal minerals, the laborious and not always satisfactory method of picking out "pure" samples of each mineral from many localities was employed. However, the results obtained have justified the time that has been spent. Not only have the conclusions arrived at in different mining areas been in accordance with one another but in many instances they have afforded scientific support or explanations for much of the knowledge that operators in the various camps have acquired by practical experience. Although many of the conclusions are not new, many of the facts are, and the results, if they do nothing else, serve to confirm the findings of some of the other workers in this field, particularly the work of Nissen and Hoyt1 and of F. N. Guild2. Dr. S. G. Lasky3 has suggested a novel method for determining from a series of algebraic equations the amount of silver controlled by each of the base-metal minerals but I doubt very much whether his method can be justified, chiefly because there appear to be more variables to be considered than the few that appear in his equations. Typical Examples of Irregular Silver Distribution Combination Mine, New Mexico, U.S.A.—In this mine an examination of the assay plans either of the mine or of the average mill feed or products

Jan 1, 1935

By Harry V. Warren

During the past few years the author has had an opportunity to examine a number of base-metal mines in the western United States, France and Spain. Nearly all of these mines produced some silver, and laboratory studies of the relationship between the silver and the various base-metal minerals in the ore have given some interesting and, it is to be hoped, enlightening facts. As this work was undertaken primarily to ascertain the amount of silver chemically associated with, not controlled by, the various base-metal minerals, the laborious and not always satisfactory method of picking out "pure" samples of each mineral from many localities was employed. However, the results obtained have justified the time that has been spent. Not only have the conclusions arrived at in different mining areas been in accordance with one another but in many instances they have afforded scientific support or explanations for much of the knowledge that operators in the various camps have acquired by practical experience. Although many of the conclusions are not new, many of the facts are, and the results, if they do nothing else, serve to confirm the findings of some of the other workers in this field, particularly the work of Nissen and Hoyt1 and of F. N. Guild2. Dr. S. G. Lasky3 has suggested a novel method for determining from a series of algebraic equations the amount of silver controlled by each of the base-metal minerals but I doubt very much whether his method can be justified, chiefly because there appear to be more variables to be considered than the few that appear in his equations. Typical Examples of Irregular Silver Distribution Combination Mine, New Mexico, U.S.A.—In this mine an examination of the assay plans either of the mine or of the average mill feed or products

Jan 1, 1935

During the past few years the author has had an opportunity to examine a number of base-metal mines in the western United States, France and Spain. Nearly all of these mines produced some silver, and laboratory studies of the relationship between the silver and the various base-metal minerals in the ore have given some interesting and, it is to be hoped, enlightening facts. As this work was undertaken primarily to ascertain the amount of silver chemically associated with, not controlled by, the various base-metal minerals, the laborious and not always satisfactory method of picking out "pure" samples of each mineral from many localities was employed. However, the results obtained have justified the time that has been spent. Not only have the conclusions arrived at in different mining areas been in accordance with one another but in many instances they have afforded scientific support or explanations for much of the knowledge that operators in the various camps have acquired by practical experience. Although many of the conclusions are not new, many of the facts are, and the results, if they do nothing else, serve to confirm the findings of some of the other workers in this field, particularly the work of Nissen and Hoyt1 and of F. N. Guild2. Dr. S. G. Lasky3 has suggested a novel method for determining from a series of algebraic equations the amount of silver controlled by each of the base-metal minerals but I doubt very much whether his method can be justified, chiefly because there appear to be more variables to be considered than the few that appear in his equations. Typical Examples of Irregular Silver Distribution Combination Mine, New Mexico, U.S.A.—In this mine an examination of the assay plans either of the mine or of the average mill feed or products

Jan 1, 1935

By Julianne H. Glarmaty, Peter J. Conroy

INTRODUCTION In 1970 the percentage of underground coal extraction by longwall mining methods in the U.S. was 2.1 percent. This figure rose to 4.4 percent in 1976 and is expected to rise to 12 percent by the year 1985. This figure represents 46.0 million tons (51.0 million st) of annual production (Kuti, 1978). In addition, OSM regulations are placing emphasis on subsidence prediction. Section 784.20 of the Office of Surface Mining regulations for underground mining permit applications requires the sutauission of a subsidence control plan which may include monitoring. Because of its nature, longwall mining does not have flexibility in leaving pillars under structures as does room and pillar. Mining in some areas, particularly in the Eastern Coal Field, is approaching more developed areas; therefore, a greater number of structures are expected to be undermined in the near future. Subsidence engineering is becoming an important aspect of mine planning, and should be directed at predicting potential structural damage. The question operators are increasingly faced with is "what will be the subsidence effects for a specific structure at a specific location in respect to a longwall panel?" The most significant variable in assessing the subsidence effect on structures is not vertical subsidence. The variables of strain and tilt are responsible for more structural damage than is the vertical movement. Table I presents threshold values of strain for various structures (Geddes 6 Cooper, 1962). Based on National Coal Board experience, horizontal strain is approximately inversely proportional to the radius of curvature of a circular portion of a subsidence profile; therefore, the radius may be useful in estimating the magnitude of strain caused by subsidence (Hoebs, 1982). The radius of curvature can be determined by the following equation:

Jan 1, 1982

R. H. THURSTON, Cornell University, Ithaca, N. Y. (communication to the Secretary): The " tri-axial diagram" was, I think, first employed by me in the work of the " U. 8. Board Appointed to Test Iron, Steel and Other Metals." A model was exhibited to the American Association for the Advancement of Science, and the diagram was first published, and the model described, in a paper presented to the same society at its Nashville meeting in 1877." The problem then presented to its inventor was to find a method of planning a research involving proportions of ternary compositions in such manner that, a limited number of such compositions being tested, the results should give the law of variation in the physical properties of all possible combinations of the three elements, and the actual numerical values of such as were important to the investigator. The investigation of the binary alloys, copper and tin, copper and zinc, and tin and zinc, had been completed and satisfactorily discussed, employing the usual bi-axial diagram, of which the ordinates represented the one, and the abscissæ the other, of the characteristic properties to be studied, the composition being commonly indicated by the abscissæ. In these cases it was easy to ascertain, by the study of a limited number of compounds, the law of variation in strength, ductility, etc., with composition; but, for a long time, the ternary alloys were not attacked, because no simple and satisfactory method presented itself of securing results significant for the whole field by the investigation of a comparatively small number of alloys. The tri-axial diagram was finally hit upon as a means of representing and interpreting results, and researches were at once begun, and in due time satisfactorily completed.

Jan 1, 1899

By Harry V. Warren

During the past few years the author has had an opportunity to examine a number of base-metal mines in the western United States, France and Spain. Nearly all of these mines produced some silver, and laboratory studies of the relationship between the silver and the various base-metal minerals in the ore have given some interesting and, it is to be hoped, enlightening facts. As this work was undertaken primarily to ascertain the amount of silver chemically associated with, not controlled by, the various base-metal minerals, the laborious and not always satisfactory method of picking out "pure" samples of each mineral from many localities was employed. However, the results obtained have justified the time that has been spent. Not only have the conclusions arrived at in different mining areas been in accordance with one another but in many instances they have afforded scientific support or explanations for much of the knowledge that operators in the various camps have acquired by practical experience. Although many of the conclusions are not new, many of the facts are, and the results, if they do nothing else, serve to confirm the findings of some of the other workers in this field, particularly the work of Nissen and Hoyt1 and of F. N. Guild2. Dr. S. G. Lasky3 has suggested a novel method for determining from a series of algebraic equations the amount of silver controlled by each of the base-metal minerals but I doubt very much whether his method can be justified, chiefly because there appear to be more variables to be considered than the few that appear in his equations. Typical Examples of Irregular Silver Distribution Combination Mine, New Mexico, U.S.A.—In this mine an examination of the assay plans either of the mine or of the average mill feed or products

Jan 1, 1935

By D. J. Jr. McAdam

Fort the past five years, an investigation of the endurance properties of metals has been in progress at the U. S. Naval Engineering Experiment Station, Annapolis, Md. As a result of the investigations at this Station1-5 and other laboratories6-11 "endurance limits" of practically all kinds of carbon and alloy steels have been determined and have been correlated with other physical properties, especially with tensile strength. About a year and a half ago, the investigation at the Naval Experiment Station was shifted to non-ferrous metals. As a result, several papers discussing the endurance properties of numerous non-ferrous metals and alloys, especially the alloys of nickel and of copper12-16 have been published. In these papers, stress-cycle graphs illustrate. the endurance properties of each individual metal and alloy, and other graphs illustrate the effect of cold working, heat treatment, and chemical composition on endurance and other physical properties. Endurance tests of non-ferrous metals were made by the machines used in the endurance tests of ferrous metals. 1-4 The specimen for the rotating-cantilever tests, which has been described, 1,2,13 has a conical surface, with taper so adjusted that the stress is nearly uniform over a length of about 1 ½ in. Alternating torsion tests were made with the machine of the inertia types17 and usually by an accelerated-fatigue method.12 As the rotating-cantilever endurance limits of metals are about twice the alternating-torsion endurance limits, the former values are more generally useful in correlating the endurance properties of nonferrous metals. In several recent papers by the writer13-16 correlation of the endurance properties of a number of non-ferrous metals has been discussed.

Jan 10, 1925

C. W. GOODALE, Butte, Mont. (member of the committee)- (communication to the Secretary*).-In the discussion of papers presented at the New York meeting of the Institute in February, 1915, and at the Arizona meeting of September, 1916, I referred to the activities of the Bureau of Safety of the Anaconda Copper Mining Co., and I am now submitting a few thoughts by members of the staff of that Bureau. TORGUS H. OAAS, Safety Engineer, Butte, Mont.-The report of the Committee on Safety and Sanitation has described different organizations and methods of promoting safety work. The effectiveness of these methods would aid the beginner in his campaign for safety in choosing the kind of organization and methods best adapted for his field. This can he obtained only by a discussion by those who have long promoted this kind of work, and have met with successful results. As the field is new, the different organizations promoting safety work have not established a common basis of rating for their fatal, serious and slight accidents, so that it is now difficult to get a comparative basis from which to judge the merits of the different systems. C. W. GOODALE.-The U. S. Bureau of Mines adopted, at the beginning, as a basis for its yearly summaries, the number of accidents. per 1,000 men employed, and it is now (quoting from its report for 1915, Technical Paper 168) making the following "classification of injuries:" "Many of the States now have. compensation laws, and in order to conform with their classifications, the bureau's classification of serious and slight injuries for 1915 is on a 14-day (2-week) basis instead of 20 days, as in previous years. The new classification of injuries includes three types, as follows: 1. Fatal 2. Serious (time lost, more than 14 days) (a) Permanent disability Total Partial

Jan 6, 1917

By Nicholas J. Grant, Laszlo J. Bonis

Two dilute nickel alloys in each of the systems Ni-Al, Ni-Ti, Ni-Cr, and Ni-Si u:ere internally oxidized at 700° to 900°C for time periods up to 100hr to establish the oxide particle size, depth of oxide penetration, and the change in oxide particle size with depth. Fine (-270) mesh alloy powders were then intevruzlly oxidized, hydrogen sintered, compacted, and extrmded, yielding bar stock for tensile tests at room temperature and creep-mpture tests at 815° to 1093°C. Recrystallization studies were made up to 1400OC. ReCENT studies have clearly indicated that oxide dispersion strengthened alloys exhibit outstanding elevated temperature properties, espe- cially in long-time tests. Certain structural parameters must be observed to achieve optimum properties, namely, micron or submicron interpar-ticle spacing, submicron oxide particle size, and a high level of stored energy.'-5 A number of processes have been utilized to obtain the desired structures, but certain of them appear to offer greater promise. Thus far the most promising method is the internal oxidation of dilute alloys consisting of a relatively noble solvent metal and a readily oxidizable solute element.3'6)7 Several important principles governing internal oxidation have been established in earlier studies;' however, these principles are as yet not adequate to permit alloy development studies. Much of the earlier work was performed on relatively coarse wires or in idealized systems. As a result, there are still a number of unanswered questions which require considerable additional work: a) How does oxide particle size change with depth of penetration of the oxide? How does this vary with the specific type of solute element? b) What is the effect of solute content on the average oxide particle size?

Jan 1, 1962

By James H. Hance

Several years ago the writer was connected with the Mint and Assay Service of the Federal Government as Assistant Assayer at the Salt Lake Assay Office. At that time cyanide bars formed approximately half of the bullion purchased by that office. Disagreement in valuat,ion between the producer and the office was not infrequent and to a lesser extent between the Assay Office and the Mint, this latter issue being soon obviated, however, by adopting uniform methods of sampling the bars. A nice problem seemed to offer itself for research and the writer began a series of experiments which were soon terminated, however, by his going into other work, and which he regrets have not since been completed. The results attained may suggest lines of approach to this problem and are, therefore, offered in this article. Frederic P. Dewey, Assayer of the Mint Scrvice, U. 5. Treasury, has had abundant opportunity to study this phase of metallurgy, and has published several articles relative thereto.1 In the last article cited Dewey quotes analyses of cyanide bullion similar in content to that with which the writer worked, and which show some of the variations met with. In the discussion of these papers,2 comparison has been made in terms of copper bullion, but to the writer this seems of questionable value. Copper bullion may resemble silver bullion, but its similarity to gold bullion with little or no silver content is another thing. The freezing-point diagram of Roozeboom, reproduced on page 881 of the discussion cited, is for the gold-silver series as stated. The original problem under discussion, however, is not this alloy but gold with base metals other than copper. As for the statement that the corners are the worst places or

Jan 1, 1916