Search Documents

By Arthur Green

A GROUP of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point sear Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections.

Jan 1, 1936

Jan 1, 1957

[ ]

Jan 1, 1938

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By H. Conrad, E. Stofel

The fracture behavior of 60-deg-oriented sapphire crystals was investigated for both tension and compression. Plastic flow on the basal plane was found to be a factor in reducing the tensile stress required to produce fracture in the temperature RECENT experiments1-' have shown that single crystals of a alumina (sapphire) can deform plastically, particularly at temperatures greater than 1000°C. The effect of this plastic flow on the fracture behavior of sapphire was not established, but range 1100º to 1500ºC. Mechanical twins, both (0001) and (0111) types, were produced by compression in the temperature range 1100" to 1300°C. Cracks propagated more readily along the twin boundaries than in the nontwinned crystal. experiments with other ceramic crystals4'5 have shown that plastic flow can initiate cracks that lead to catastrophic failure. This suggests by analogy that plastic flow might also be an important factor in the fracture of sapphire crystals. A recent experimental investigationS undertaken to determine the mechanism of plastic flow in sapphire provided an opportunity to study the type of fracture produced after various amounts of plastic shear strain. The results of this study of fracture are reported in the present paper. During the course of

Jan 1, 1963

By Henning Nielsen

SIX weeks ahead of schedule, the International Nickel Co. of Canada Ltd. has brought a 30-mile rail line into the newly born town of Thompson, Manitoba. Its construction spurs the development of a rich new mining region slated to become the world's second largest nickel-producing area-exceeded only by Inco's Sudbury, Ont., workings. Two mines, the Thompson and the Moak Lake, will be opened to meet International Nickel's scheduled annual production goal of 385 million lb of refined nickel by 1961. Accomplishment of this aim will mean an additional 75 million lb of the metal available to consumers. In addition, stepped-up out- put of Inco's Sudbury holdings may increase this figure by another 25 million lb. (For an earlier report on these developments see MINING ENGINEERING News, January 1957).

Jan 12, 1957

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By Oliver C. Ralston

A definite field of usefulness has developed for the brine-leaching processes of removing lead from ores and other products, so this paper reviews the developments, both in practice and in research, that have taken place since the publication of two earlier papers on this subject.' Several commercial plants are now in operation and a number of semi-commercial test plants have been operated in an effort to determine the limitations of brine leaching and to compare the results with other forms of treatment. Briefly, the brine leaching of lead depends on the fact that lead chloride and lead sulfate are soluble in saturated sodium-chloride solutions. In dilute brines, the solubility of the lead salt is less than in pure water; but in the strong brines, the solubility is greater than in pure water due, supposedly, to the formation of a double sodium-lead chloride. This is seen in Fig. 1, which shows the results of M. Demassieux2 on the solubility of lead chloride in sodium-chloride solutions of different concentrations and at three temperatures. The curves are not those given by Demassieux but are calculated from his results in order to convert them to units common in metallurgical work. The right-hand branch of each curve shows that if the solution is kept in contact with solid sodium chloride the lead chloride can be almost entirely displaced from solution, but that brines which are saturated with sodium chloride, but are not in contact with the solid salt, have a very high solubility for lead chloride. The diagram gives the analysis of the solution in grams of lead per liter, although the substance actually in solution is lead chloride. At 100" C. as much as 100 gm. of lead per liter can be obtained; but at lower tem-

Jan 1, 1924

By D. Webster

It has been found that cold work and annealing treatments greatly retard subsequent grain growth and re-crystallization in thoria-dispersed nickel and NiCr. It is suggested that this is due to cavities which form at the particle-matrix interface durilzg cold work. Some of' the cavities formed are stable at elevated temperatures and prevent the mouement of large-angle grain boundaries. The movement of these boundaries at elevated temperatures is known to start recrystal-lization and when they are pinned by voids recrystal-lization is made more difficult. TD Nichro,me had a maximun resistance to recrystallization when the initial structure was coarse-grained and had a low dislocation density. A precipitation reaction occurred between 700° and 1200° F in cold-worked TD Nichrome. It has been shown by Grant and his coworkers1-3 that a large part of the strength of dispersion-hardened materials is a result of the cold-worked structure produced during fabrication. In a comparison of the strength of cold-worked copper with and without an oxide dispersion, Grant4 has demonstrated that there is little difference in strength at room temperature. The function of the dispersion is essentially to maintain the cold-worked structure at higher temperatures than is possible in the base material. The dispersion accomplishes this by making recrystallization more difficult. The mechanism by which this is achieved is discussed in this paper. The fabrication history of the material has been found to greatly influence recrystallization behavior and this aspect is discussed in some detail. I) MATERIAL Three different thoria-dispersed materials were examined. 1) DuPont 2 pet thoria-dispersed nickel (TDNi) in 0.050-in. seeet. Thoria particle size is in the range 100 to 2500A. 2) DuPont 2 pct thoria-dispersed nichrome (20 pet Cr, 80 pct Ni) (TDNiC) in 0.125-, 0.060-, and 0.040-in. sheet. In the as-received condition these sheets have

Jan 1, 1969

AT the meeting of the Board of Directors held on June 25, 1926, and in response to numerous in-dividual suggestions for changes, a committee on Re-vision of the Constitution and By-Laws of the Insti-tute was appointed, consisting of C. F. Rand, Archi-bald Douglas and H. Foster Bain. Various confer-ences were held, much correspondence conducted and a preliminary draft was prepared. It proved imprac-ticable to complete the work in time to submit the matter to the membership for approval or disapproval at the annual meeting in 1927, and the Committee was continued with instructions to prepare a report as a basis of action in 1928. After Mr. Rand's death George Otis Smith was appointed in his place and the tentative draft herewith submitted has been pre-pared in its present form by Messrs. Smith, Douglas and Bain, though not differing in any material mat-ter from an earlier draft approved by Mr. Rand. In preparing this the Committee has kept in mind primarily the desirability of simplification and of making the By-Laws conform to the actual practice of the Institute as worked out through experience. The Constitution and By-Laws adopted in 1912, and which with minor amendments only still govern the Insti-tute, are full of specific provisions regarding pro-cedure; such as that laid down for guidance of the Papers and Publications Committee. Many of these have proved unworkable and in practice have not been always strictly followed. It now seems wise to write into the Constitution and By-Laws only the general fun-damental principles to he followed and to provide for such easy change in methods of following them out as will permit efficient conduct of the business. It is this thought that has guided the Committee in rewrit-ing many of the sections. With this in view also the Constitution, as such, has been shortened to the brief-est feasible statement of fundamentals. All matters relating to means of making these principles effec-tive have been put into the By-Laws or in the hands of committees whose work is subject to control and whose rules are subject to approval or disapproval by the Board of Directors. Many suggestions for changes have come to the Committee that have not been incorporated in this draft. Some of these are in themselves excellent but have not been incorporated here because the Commit-tee discovered no sentiment for them such as would be likely to secure their approval, or found them out of harmony with the general plan followed herein.

Jan 9, 1927

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By Albert Sauveur

(New York Meeting, February, 1913.) IT is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.1 The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance.

Jan 3, 1913

By E. V. Potter, E. T. Hayes, H. C. Lukens

LARGE volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that ignite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.1.2 The close relationship between iron and man¬ganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. APPARATUS The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of I00 c.c. for a 60-cm. length. For larger changes in gas volumes; auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945

By Louis J. Demer, Paul A. Beck

As reported in a previous publication,1 isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: [ ] or in some cases, by the simpler relation, [ ] Here, D is the average grain size after an annealing period t. The annealing period includes the time for complete recrystallization R, and the time for grain growth [to]. DA is the grain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pct magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystallization and grain growth of the 2 pct magnesium alloy at 350°C. EXPERIMENTAL PROCEDURE The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table I and magnesium from a high purity distilled stock of magnesium crystals. [ ] Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. [ ] The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up t0 1500X, revealed a cer-

Jan 1, 1948

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981

By Allan J. Clark

It is nearly three years since the metallurgy of the Homestake ore was discussed with considerable thoroughness, in a paper1 read before the Institution of .Mining and Metallurgy. Certain changes have been made in this period which are perhaps of sufficient interest to justify a brief description, and it is chiefly with such details and miscellanies that this paper will deal. In the circumstances, a certain amount of repetition is inevitable, but matter treated of in the former paper will be referred to here only when it is necessary for the sake of coherency. For full descriptions of equipment and technique, the former paper should be consulted. The mineralized slates and schists which constitute the ore vary considerably in composition, but the unoxidized ore, perhaps constituting the major part of the reserves, contains either chlorite or hornblende (cummingtonite), with quartz, carbonates of lime, magnesia and iron, and arsenopyrite, pyrite, and pyrrhotite. Ferrous minerals predominate, and this fact has been an important factor in determining the metallurgical treatment. With one or two exceptions the minerals noted are of relatively high specific gravity, and the ore as a whole is exceptionally heavy, many determinations giving an average specific gravity of 3.00. This high specific gravity presents one decided advantage, when the cost of treatment is compared with operations elsewhere, in that the ton, almost universally the basic unit, represents a volume probably less by 10 per cent. than that of many gold ores. On the other hand, this high gravity renders more difficult the discharge of pulp from mortars, its distribution on amalgam tables, and its transportation in launders. In the same way, as attesting the usual balance of such variations of different ores, it may be noted that the needle-like fibers of hornblende (cummingtonite), interlacing throughout the mass, render the ore more difficult to crush than would be anticipated, but on the other hand assist

Jan 1, 1916

By Samuel B. Christy

" The man is always greater than his work." The training of the men who are to develop the mineral resources of the world is the most important problem connected with mining engineering. It becomes ever more important to civilization as the mineral wealth of the earth approaches exhaustion. I have therefore decided to consider a few of the more important problems arising in the training of the mining engineer, and especially those arising in America. , The Peculiar Nature of Mineral Wealth. Mining and Agriculture are the two fundamental arts. Without the latter our existence would be precarious; without the former, our civilization impossible. Agriculture furnishes that regular supply of food and raiment which leads to the growth of large communities in which cultivated leisure first becomes possible; while mining furnishes the metallic thread from which is woven that complex fabric we call civilization. But in these two arts the conditions for success are widely different. Most of the crops that the farmer reaps may be harvested year after year, and the proper fertilizers being added, he may continue the annual harvest indefinitely, while, as a result of cultivation, his farm becomes yearly more valuable. But the crop the miner reaps can be harvested but once in the history of the race. Our mineral wealth has taken unknown ages to mature in the bosom of the earth. The ripened fruit can be plucked but once. There are no fertilizers for worked-out mines. It never pays to work over a mine that has been

Jan 1, 1906

By F. E. Buch

The smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The :smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pet moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pet oxide copper. The predominating minerals are chalco-cite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. General Description Flotation concentrate, containing 10 Pet moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and Spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which Prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been Set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1949

By W. H. Brandt

THERE has been much progress in the last two decades in understanding the hardenability of steel. Roughly, the progress has been along two lines, which may be designated as empirical and fundamental. This empirical work has progressed to the point where steels may be manufactured to the desired characteristics quite closely and heat-treatment and application problems can be approached with considerable confidence. Particularly noteworthy among the empirical work is that of Grossmann,12 who has given formulas for calculating hardenability as a function of composition, and the establishment of the isothermal transformation curve by Davenport and Bain.13 The latter does not fall entirely in the class of an empirical study, for while it provides a means of presenting a tremendous amount of empirical data in the form of a single curve, it also outlines clearly the problems that face the fundamental investigator. The isothermal transformation curve shows clearly that the phenomena occurring in the neighborhood of the knee of the curve are those that limit the hardenability of steel. Above the knee of the curve, the product of decomposition of austenite is lamellar pearlite and fundamental progress has consisted chiefly of a detailed study of structure and formation of pearlite, largely at the hands of Mehl and his collaborators.1-5 They have shown that formation of pearlite proceeds by a process of nucleation and growth and they measured both the nucleation and growth rate. However, there is still a wide gap between our empirical knowledge and fundamental knowledge, owing largely to the fact that there is no satisfactory theory of nucleation rate or of growth rate. This paper is being written in an attempt to fill in a small part of the gap. A method was presented recently14 for calculating the velocity of edgewise growth of pearlite using an expression for the carbon concentration that satisfies the diffusion equation. The edgewise velocity of pearlite growth in a plain carbon eutectoid steel was calculated, using linear extrapolations of the ferrite and cementite solubilities. While the results are in fairly good agreement with the experimental facts, the calculated velocity of edgewise growth is smaller at 600°C. than G, the radial growth velocity of pearlite nodules, whereas one would expect it to be larger. In this paper the calculation will be repeated using a new extrapolation for the ferrite solubility, which gives better agreement between G and V, the calculated velocity of edgewise growth. A calculation will also be made of the effect of carbon content on velocity of edgewise growth, and the problems of calculating the effects of other alloying elements on growth rates will be discussed. It will be assumed that the mechanism of pearlite growth, established by Mehl and

Jan 1, 1945