Search Documents

By M. Duclos, A. Sawatzky

A simple model has been developed which describes the steady-state solute distribution in Ti-H type systems above the eutectoid temperature in the presence of a temperature gradient. The solute distribution is dependent on the shape of the phase boundaries. An interesting result, and one that is not observed at steady state in thermal diffusion below the eutectoid temperature, is the existence of a two-phase region. The heat of transport for hydrogen in a titanium, Q*a, over the temperature range 275" to 650.C is determined to be 4500 * 230 cal per mole. The heat of transport for hydrogen in B titanium, QB* over the temperature range 320" to 590.C is found to be 630 ± 200 cal per mole. It is also shown that thermal diffusion provides a method by which phase bounduries above the eutectoid may be determined in Ti-H type systems. IN modern technology materials are being used at constantly increasing temperatures under greater temperature gradients. Thus atomic migration in metal alloys due to a temperature gradient (thermal diffusion) may in some cases occur to an observable extent. The thermal diffusion of hydrogen in zirconium has in recent years received considerable attention1-' because of the use of zirconium alloys in nuclear power reactors. The thermal diffusion kinetics below the eutectoid (547°C) are fairly well understood. At steady state the solid solution, a, and hydride, 6, phases are completely separated with the hydride precipitating at the lower temperatures. No experimental work has been carried out in the a + B region although Droege4 suggested that a complete separation of the two phases, as observed at temperatures below the eutectoid, might not always occur. In the present investigation a simple model has been used to determine the steady-state solute distribution under a temperature gradient in Zr-H type systems heated above the eutectoid temperature. The solute distribution is shown to be dependent on the shape of the phase boundaries in the constitutional diagrams and several typical cases are discussed. The model has been applied to Ti-H. This system was chosen in preference to Zr-H because of its much lower eutectoid temperature (-300°C as compared with 547.C), thereby reducing experimental errors due to oxidation and hydriding. The heats of transport for hydrogen in the a and B phases of titanium also have been determined since they were required to compare the proposed thermal diffusion model with experiment. THEORY In the presence of a temperature gradient the atomic flux in a single-phase region of a two-com-ponent system of which the atoms of only one component are diffusing is given by:' J = - U\dx + RT3 dx) which can be written as: j-D(dn/dt +Q*n/RT2)dt/dx [11 J - -D\dT + RT2)dx [1] where D = diffusion coefficient, n = solute concentration, T = absolute temperature, R = gas constant, dT/dx = temperature gradient, and Q* = heat of transport. At steady state (J = 0) Eq. [I] leads to the solute distribution: n = noexp Q*/RT where no = a constant depending on total solute content. The heat of transport Q* can be experimentally determined from the steady-state distribution. In the present paper we shall determine the solute distribution in systems having the constitutional diagram exemplified by Ti-H shown in Fig. l.' As shown, N,(T) and NB(T) are the equilibrium solute concentrations in the a and 0 phases at temperature T. Lines AA' and CC' define the region of interest to us. The following assumptions are made: 1) Steady-state conditions prevail. 2) In a single-phase region all points on an isotherm have the same thermodynamic potential so that the composition over an isotherm is uniform. If a two-phase region exists, thermodynamic equilibrium is found only at phase interfaces. However, we assume the component of the concentration gradient along an isotherm to be small so that the composition in each phase is approximately the same as at the interface and is given by the constitutional diagram, Fig. 1. 3) There is appreciable diffusion of only one component. 4) We shall consider only the case where Qa*, QB*, and Qg*, the heats of transport for solute diffusion in the a, B, and 6 phases, respectively, are positive. This has been observed for the thermal diffusion of hydrogen in zirconium3 and titanium.10 We will show that the steady-state solute distribution above the eutectoid is primarily determined by the heats of transport and the temperature dependence of Na(T) and Np(T). It may be quite different from the steady-state distribution below the eutectoid. For example, we will see that, under certain conditions,

Jan 1, 1970

By Nagel, Theodore

USE of oxygen in metallurgical operations was investigated by a committee of unusually able engineers more than ten years ago. A record of their work appeared under the title "The Use of Oxygen or Oxygenated Air in Metallurgical and Allied Processes," Serial 2502, Report of Investigations, U. S. Bureau of Mines. Shortly thereafter the A.I.M.E. published "Use of Oxygenated Air in Metallurgical Operations," based on a symposium at the New York meeting, February 1, 924. Quoting from the Bureau of Mines report In view of the many recent developments in oxygen manufacture, and considering the increasing cost and decreasing quality of our raw materials, the Bureau of Mines has taken the matter of the application of oxygen or oxygenated air to the metallurgical centers for consideration and has appointed an advisory committee to study the problem.

Jan 1, 1935

By Gerard C. Gambs

The electric utility industry is the largest customer of the U.S. coal industry, consuming nearly 50% of present coal production. By 1980, the electric utilities are expected to burn over 500 million tpy of coal or 75% of total coal production. When coal is burned in electric utility plants, ash is produced in one of several forms. These include fly ash, bottom ash and bottom slag. At the present time, approximately 20 million tons of these ashes are produced and must be disposed of by the utilities at a cost of 50[c] to $2 per ton. In 15 years, more than double this quantity will be produced. Only a small quantity of this ash is put to any practical use. Much remains to be done about expanding uses for fly ash and bottom slag.

Jan 1, 1967

By V. H. Gottschalk

SEVERAL years ago a group in the metallurgical division of the U. S. Bureau of Mines began a study of the application of new developments in physics to metallurgical problems'. Among these developments were the extensions of what may be termed by analogy the "sound spectrum." Electromagnetic waves, from X-rays to radio waves, have been quite thoroughly explored for metallurgical use, but the sound spectrum, extending from low-frequency vibrations involved in certain types of metal failure by fatigue through the range of audible sound to inaudible vibrations having frequencies of many kilocycles, has had only meager consideration from metallurgists. Because of the general interest in the process recently demonstrated by St. Clair3 for flocculating smoke by means of sound waves, this article is written to point out possible applications of sound and supersonic (ultrasonic) waves in the metallurgical industry.

Jan 1, 1937

By George F. Comstock

It seems a common opinion among metallographists that all light-gray inclusions seen with the microscope in polished sections of steel are manganese sulphide. Examples of this belief are continually appearing, as for instance in the paper by Dr. Henry Fay on manganese sulphide as a source of danger in steel railsll and in Lieutenant-Commander Cook's paper on Metallography of Steel for U. S. Naval Ordnance.² Slate- colored inclusions are considered to be silicates, and dove-gray inclusions, manganese sulphide. To show the danger in the latter unqualified assumption, it should be sufficient to examine the edge of any piece of steel that is covered with a fairly thick scale, and that has been polished in such a way as to prevent the scale from breaking away entirely below the polished surface. This can be done by protecting the scaled edge of

Jan 1, 1917

By Robert G. Peets

After 216 years, the end of operations at the Corn- wall mine can be foreseen within the next two decades. The story starts in 1732 when three sons of Wiliam Penn-John, Thomas, and Richard-deeded 9669 acres in the Province of Pennsylvania to a Joseph Turner, who assigned it to William Allen. In 1734 Peter Grubb, who had prospected for iron in the area, paid Allen £ 135 for 300 acres of this tract in what is now Lebanon County. In 1737 he was granted a warrant for 142.5 additional acres, which included three hills of outcropping magnetite described as "rich and abundant, forty feet deep, commencing two feet under the earth's surface." This seemingly inexhaustible reserve was to become one of the most valuable deposits in the U. S. before the ore-rich Lake Superior region was developed.

Jan 7, 1957

By AIME AIME

RECENT experiments in reflected sunlight photography in mine shaft's' and. slopes in the McAlester, Oklahoma, coal-mining district have been so satisfactory as to indicate that such a method has definite scientific value. The entrances to abandoned deep shafts and slopes on Choctaw and Chickasaw Indian coal lands in Oklahoma are being filled or bulk-headed by the U. S. Geological Survey under Public Works Project F. P. 63-C&C. Inasmuch as these mines may be reopened at some future time when there is a demand for coal, H. I. Smith, Chief of the Mining Division, suggested that photographs of deep shafts would be of value. Such photographs would show timber details and the general condition of the walls. Photographic records of the exact status of shafts when filled will facilitate operations in reopening.

Jan 1, 1936

By Arthur Taggart

THE following conclusions on the work of the Hardinge mill are based on data furnished to the writer by the Hardinge Conical Mill Co. in the form of the mesh cards hereto appended. Energy units (E. U.) and relative mechanical efficiencies (R. M. E.) are computed by the "volume method" of Stadler.1 Screen apertures used are the average apertures of testing screens of the meshes given. Card 122. June 28, 1912. Vipond Porcupine Mines Co., Ltd., Schumacher, Ont., Canada. Ore from mill bin. Gangue, quartz and basalt. 4.5 ft. by 13 in. ball mill. Capacity, 48 tons per 24 hr. Charge, 4,000 lb. balls. Speed, 33 rev. per minute. Horsepower, 15 to 17. Water, 100 per cent. by weight. (50 per cent. ?) Product deslimed and oversize reground-in pebble mill, see Card 113. Feed to mill through 2-in. mesh.

Jan 7, 1915

By John B. Malcom

The discovery of tungsten-bearing quartz outcrop- pings in Vance County, N. C., by the Hamme brothers in 1942, made international news in the mining industry and was, in fact, one of the major ore discoveries made in the U.S. during the last 25 years. Operations began at the Hamme mine in 1942, but after 16 years of successful operation, the mine was closed down in 1958 under adverse market conditions. By that time, it had produced nearly 20 million lbs of metallic tungsten. Because of the square-set timber mining method then in use, mine operating expenses were high, actually representing 78% of the total operating expenses at the property. In timber work alone, 160 men were employed. Approximately 500,000 bd ft of timber were placed monthly at a direct supply cost of $1.00 per ton of ore mined.

Jan 4, 1962

By Gerald A. Munson, Fremont F. Clarke

During recent years the use of lithium has expanded greatly in industrial, chemical, and metallurgical fields, while at the same time modernized methods of mining and refining lithium have increased production. Technical literature includes many papers describing the geology and mineralogy of lithium deposits. Mining and beneficiating problems, however, have not been thoroughly described. Published reports have failed to emphasize that one of the chief reasons lithium minerals were not extensively mined until recently is the difficulty of beneficiation. Four lithium minerals of pegmatites and the lithium-sodium-phosphate byproduct from the brines at Searles Lake, Calif., have been sources of lithium. Among the pegmatite minerals, only spodumene and petaline are known to occur in deposits large enough to support large tonnage operations. Spodumene, a lithium-aluminum-silicate, is the principal lithium mineral mined in the U. S.

Nov 1, 1955

By C. E. Wood

THIS paper is a brief report of experimental work undertaken to determine whether barium oxide in any quantity increases the desulfurizing action of blast-furnace slags. Industrial furnace operation with slag containing small quantities of barium oxide, referred to later, interested S. A. Sanford of the Commercial Chemical Co., Youngstown, Ohio, to conduct experiments to furnish comparative results on desulfurization with normal slag and slag containing small quantities of barium oxide. The U. S. Bureau of Mines agreed to assist on the problem because of the possible saving in fuel if the desulfurizing action of blast-furnace slag can be substantially increased, also because the experiments would yield new information on sulfur elimination in general, a matter of economic importance in furnace practice. A more complete and fundamental study of desulfurization of iron by slag is in progress.

Jan 1, 1929

By M. F. Goudge

Production of many industrial minerals reached all-time records in 1965. In keeping with the high level of industrial activity throughout the nation, producers of many industrial minerals operated at capacity or near capacity, notably the producers of phosphate, potash and sulfur. In the case of sulfur, the demand exceeded production and orders were filled, in part, from stocks accumulated in previous years. Industrial minerals as a group continued to increase both in value and quantity at a faster percentage rate than metallic minerals and fuels, The U.S. Bureau of Mines estimated that the value of industrial minerals produced in 1963 was $4318 million vs. $2006 million for metals. Preliminary estimates for 1965 indicate that current value of production was again more than 2% times that of metals, thus making apparent their importance to the industrial life of the nation.

Jan 2, 1966

NEW MEMBERS The following list comprises the names of those persons who became members during the period Oct. 10 to Nov. 10, 1915: Members BECK, WESLEY HUDSON, Civ. and Min. Engr., Ellsworth Collieries Co., Ellsworth, Pa. BRADSHAW, GRANT D., Pres., Andrews-Bradshaw Co, 409 Diamond Bank Bldg., Pittsburgh, Pa. BUTLER, BERT S., Geol U. S. Geological Survey, Washington, D. C. CAMERON, FRANK, Asst. Mine Foreman, Braden Copper Co., Rancagua, Chile, So. Amer. CHEN, YEFAH FRANCIS, Asst. Min. Engr., Pinghsiang Colliery, Pinghsiang-Ki, via Changsha, China. CLAGHORN, DAVID MONTGOMERY, Mining Engr., Timekeeper, Wilkeson Coal & Coke Co., Wilkeson, Wash. DAVIS, REUBEN WALDO, Min. Engr., Supt., Cannel Coal Co., Dolores, Webb Co., Tex. DOUTHETT, GEORGE M., Supt Crescent Metals Co., Glenwillard, Pa. DUNSFORD, ENSOR R., Min. Engr., Asst. Supt., Victoria Gypsum Min. & Mfg. Co., Ltd., Quarry, St. Alms. C. B.. Nova Scotia. Canada.

Jan 12, 1915

By D. F. Atkins, B. A. Rogers, E. J. Manthos, M. E. Kirkpatrick

A phase diagram of the uranium-columbium alloys is presented. The apparatus and the procedures used in obtaining the data are described. Data from which the diagram was drawn are given in tabular and graphic form. THE use of uranium in the production of energy from nuclear fission has given considerable im- petus to the investigation of the metal and its alloys. Accordingly, information concerning the phase diagrams of binary alloys of uranium with other elements is of interest to metallurgists engaged in nuclear-engineering activities. As a contribution to the knowledge of the binary alloys, the authors have attempted to establish the diagram of the uranium-columbium system. The reports of laboratories engaged in work for the Manhattan Engineering District and the U. S. Atomic Energy Commission contain a number of references to work on uranium-columbium alloys.

Jan 1, 1959

By M. Earl Volin, M. Adnan Goksel

The hydro thermal agglomerating process described (U.S. Pat. No. 3,235,371, 1966)* is different from the cotzventional high-temperature processes. Green pellets or briquettes made with mixtures of moist iron-ore concen- trates and burned or hydrated lime fines are hardened in an azttoclave at 198°C and under steam pressure for 112 to 5 hr, with or without previous drying. Under the neutral conditiotzs, oxidation of magnetite does not occur as in the conventional processes. The resulting azzlomerates-- are hard and resistant to abrasion and weathering, and they do not disintegrate in the Under test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperamre and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1970

By Edward Ernst, Richard Runvik

AT the U. S. Gypsum Co. mine in Oakfield, N. Y., a flat-lying vein of rock gypsum is mined by the room and pillar method. Averaging only 4 ft thick, this vein is 1200 to 6000 ft in mineable width and many miles in length. Overlying the vein throughout the mine is a 2-ft thickness of distintegrated gypseous shale and fractured limestone which parts easily, falling with little or no warning. This shale, known as ash, varies in thickness from less than an inch to more than a foot. Small veinlets of selenite cut this shaley material, which breaks around timber props. The 18-in. limestone over-lying the ash is fractured vertically into blocks of varying size and will fail if any but the shortest unsupported spans are permitted. Above these two members is a thick layer of competent limestone.

Jan 6, 1957

By William M. Huang, T. Carl Shelton

There are undoubtedly many factors that affect the emission of gas from coal but the permeability of coal to gas flow would seem to be fundamental. However, there is very little information on coal permeability to gas flow available in the U.S. at the present time, despite the fact that such knowledge would appear to be significant in any degasification effort. Studies made recently in the mining engineering laboratories at Virginia Polytechnic Institute have determined values of permeability on one-inch cubes of selected coals. COAL PERMEABILITY The permeability values given in this paper are based on adaptations of Darcy's Law formulated by Henry Darcy in 1856 from experiments with fluid flow in porous media.' Using air as the gaseous fiuid, they were obtained by employing similar methods as are used to determine the permeability of petroleum and gas reservoir rock specimens.

Jan 5, 1962

By George M. Schwartz, Ian L. Reid

The Soudan mine in the Vermilion district of northeastern Minnesota is the oldest iron mine in the state. It has shipped ore every year since 1884 and still contributes a yearly quota of high grade lump ore. No comprehensive report on the Vermilion iron-bearing district has appeared since Clements' monograph,' but Gruner' discussed the possible origin of the ores in 1926, 1930, and 1932, and recently Reid and Hustad have added data on mining and geology." For many years geologists of the Oliver Iron Mining Div., U. S. Steel Corp., have kept up to date a series of plans and vertical sections of the Soudan mine. In connection with mine operation considerable diamond drilling has been done, and this, together with the mine openings, has permitted a reasonably accurate picture of the structure of the orebodies and wall rocks.

Jan 3, 1955

By S. A. Braley

Drainage of acid mine water into surface streams of coal mining areas is one of the most serious problems of stream pollution, since there is no known method that completely prevents its forming and no economically feasible treatment after it has formed. The mine acid problem differs from other pollution hazards because acid production does not end with cessation of mining but actually becomes more evident when pumping is stopped. The acid problem in the Pennsylvania, Ohio, West Virginia, and Kentucky bituminous coal areas of the U. S. began with the first operation in 1761, and the volume of acid discharge today is largely the cumulative result of years of mining. Provided they lie above the drainage area, the oldest mines, now long abandoned, are almost without exception producing acid in the same manner as those now operating or recently abandoned.

Mar 1, 1956

By Immo H. Redeker

The Asheville Minerals Research Laboratory at North Carolina State University is engaged mainly in applied nonmetallic mineral processing research to assist the North Carolina mining industry. The laboratory helped to bring the flotation process to North Carolina feldspar. spodumene, mica and phosphate producers and it maintains a versatile batch and pilot plant. The conservation of mineral resources through improved processing methods has been the object of most of the laboratory's projects. Current laboratory work is sponsored by three feldspar companies, the State of North Carolina, and the U.S. Bureau of Mines. This work is aimed at reducing the amounts of feldspar tailings in the Spruce Pine area. Mineral dressing techniques are applied to these tails to reclaim salable mineral products such as feldspar, mica, quartz, and to make a more uniform material for possible ceramic and other applications.

Jan 1, 1970