Search Documents

By P. G. Winchell, J. K. Jackson

The strtcture of body-centered Fe-Ni-C alloys (0 to 16.5 wt pct Ni) containing less than 0.015 wt pct C was investigated by measuring the carbon-diffusion peak at low frequencies with a torsion pendulurrr. By determining the Snoek damping in ferrite and in quenched alloys of identical composition, the effects of nickel content and heat treatment were separated, and the existence of a structure in which Snoek damping is greatly reduced was revealed in the quenched ternary alloys. The relative amount of this structure increases with increased nickel content and cooling rate. It is proposed that this structure may be highly imperfect or tetragonal. In Fe-Ni-C alloys containing only ferrite the addition of nickel (0 to 5.1 wt pet) decreases tke area of the carbon-diffusion peak and shifts its position to lower temperatures but broadens the peak only slightljl. The decrease in peak area with increasing nickel implies that short-range interactions with the nickel atoms prevent some of the carbon atoms from participating in the relaxation process. The shift in the peak position indicates a long-range effect of nickel on the movement of carbon atoms so that at 300°K the diffisivity of carbon in -ferrite is increased by about 35 pct by the addition of 5.1 tut pct Ni. The results are presented as distributions of relaxation strength 072 the activation energy under the assumption that the frequency factor is invariant. BODY-CENTERED iron-base solid solutions dissolve carbon interstitially in the octahedral sites. The occupation of an octahedral site produces a tetragonal distortion of the surrounding lattice. These sites fall into three sets according to the orientation of the tegragonal distortion associated with each and may be identified by their lattice coordinates as: type 1/2 0 0, type 0 1/2 0, type 0 0 1/2. At low carbon levels in cubic ferrite the carbon atoms are distributed at random1 among these sites. In high-carbon body-centered iron-base solid solutions, which are unstable with respect to several two-phase mixtures, a tetragonal structure occurs as the product of the diffusionless transformation of austenite. This transformation is commonly accompanied by appreciable microstrain and its product is called martensite. The tetragonality of martensite, a supersaturated solution of carbon in a iron, is maintained prior to decomposition even though local diffusion of carbon occurs as evidenced by carbide precipitation. The tetragonality is taken as evidence that one set of octahedral sites is preferentially occupied by carbon. (This preferential occupation is called ordering below.) Support for this view is presented by the absence of strain-induced carbon-atom diffusion in high-carbon solid solutions (martensite). Such diffusion occurs in ferrite and produces the 40°C internal-friction peak observed at 1 cps frequencies.' Thus, there appears to be qualitative evidence favoring the view that at sufficiently high carbon levels tetragonality arises spontaneously as a result of the ordering of the carbon atoms; however, no experimental evidence exists concerning an equilibrium between cubic and tetragonal body-centered solid solutions. Moreover, attempts to estimate the energy of ordering7-' predict a value too low to maintain the tetragonality observed at medium carbon levels, 0.3 to 0.6 wt pct C. In the present work an attempt using internal-friction measurements is made to establish the presence or absence of tetragonality in low-carbon body-centered solid solutions formed by quenching austenite. Fe-Ni alloys containing about 0.01 wt pct and 0 to 15 wt pct Ni were selected for the study. While the work was in progress Gilbert and Owen10 reported that the transformation which occurs in these alloys during quenching at rates up to 5000°C per sec is not martensitic but is more properly categorized as massive. Thus, the solid solution

Jan 1, 1964

By Frederick C. Hull, Robert F. Mehl, Robert A. Colton

IT is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.1,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in 1939.3 Two types of process were described: (1) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemi¬spheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. 1);2.4 the former, occurring near the knee of the S-curve has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ae1, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important 1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenability; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels.* PREVIOUS DATA ON RATE OF NUCLEATION AND RATE OF GROWTH Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Mehl,1 and by Dorn, De Garmo and Flanigan.2 It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given.

Jan 1, 1942

By George H. Ashley

At the beginning of the war, about 13 years ago, a conference was called in Washington to lay plans for pooling the coals of the United States. A careful review of the various systems of classification then extant showed none well adapted to the needs of coal pooling. The system of Tidewater pools then adopted, using numbers to distinguish one pool from another, was based on typical coals of different localities. At that time, the writer undertook the preparation of such a practical classification. Aside from drawing on his experience of over 20 years in the coal fields of the United States, reaching from the Pacific Coast and the Rio Grande to Rhode Island, he first examined and carded all of the large collection of coals in glass jars made by and for M. R. Campbell. Next, he carded all of the descriptions of coals he could find in the U. S. Geological Survey bulletins and elsewhere, as well as practical tests of coals by the Navy and other organizations and then took account of every published coal analysis of the U. S. Geological Survey and U. S. Bureau of Mines. A study of this information, involving thousands of recomputations, led to the presentation of a paper on "A Use Classification of Coal" before this Institute at the Chicago meeting, September, 1919. That classification was unique (1) in a classification based on "standard coal" which included moisture, but used standardized ash, sulfur and nitrogen, (2) in using physical properties to distinguish the major classes or orders, (3) in recognizing British thermal unit values in the minor subdivision, (4) in the large number of classes recognized (thirty-six), (5) in proposing mineral names for all classes, (6) in proposing a letter code for the several classes for practical use, (7) in proposing a code for expressing what has commonly been called "grade" of the coal, the grade code to be combined with the rank code to designate and describe a coal. The writer still thinks that the principles then offered, though not necessarily the exact proposals, are valid and desirable in any practical classification. The actual classification of coal by rank was based on the ratio of fixed carbon to volatile matter for the high-rank coals—the well-known

Jan 1, 1930

By David L. Riley

Organization The Foundling Years - 1901-1921 Two events that occurred in the decade of the 1870's have had far- reaching effects upon the petroleum industry in the U. S. and formed a basis for the birth and growth of the petroleum engineering profession. In 187 1 a group of mining engineers banded together to form the American Institute of Mining Engineers "to promote the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by all lawful means". Although it was to be 30 years before an event in Jefferson County, Tex., would cause petroleum to come into prominence as the world's principal source of energy, the founding of AIME provided an organization through which the application of engineering to the recovery of petroleum and natural gas could be developed. In 1875, a Pennsylvania judge who was called upon to make a decision for which there was no precedent reasoned that oil and gas were like wild game - they belong to the man who can reduce them to possession. His decision sired the "rule of capture", which stated that a landowner possesses the oil produced from his well, even though it might have come from beneath his neighbor's land. This interpretation prevailed for more than half a century, during which time gold-rush tactics were employed in the drilling and production of many oil fields in the U. S. The resulting overproduction and tremendous waste led to a virtual economic collapse of the U. S. petroleum industry by the early 1930's. To bring these malpractices under orderly control, proration and conservation policies were developed, and petroleum engineering became the medium through which they were devised and implemented. At the turn of the 20th Century, more than 90 percent of this country's oil production came from the East, but the picture changed with dramatic suddenness on Jan. 10, 1901. Captain Anthony F. Lucas, an Austrian mining engineer, had noticed concentrations of oil and gas near salt domes during mining operations on the Louisiana Gulf Coast. In 1899 he leased a low mound near Beaumont, Tex., began drilling, and after almost 2 years of intermittent operations, brought in the famous "Lucas Gusher"

Jan 1, 1971

By Richard E. Gray, Robert W. Bruhn

INTRODUCTION Underground coal mining has been practiced in the United States for over 200 years. Much early mining was not as efficient as today and unrecovered coal pillars, often of variable size and spacing, remain to support the overlying strata after mining has ceased. These conditions constitute a potential subsidence problem since the pillars will eventually fail. The possibility of subsidence above an abandoned mine must be anticipated except when total extraction has been achieved, permitting subsidence concurrent with mining, or when large coal pillars which have an adequate factor of safety for long-term support remain in the mine. Coal is found in 37 states and is mined under- ground in 22 states (HRB Singer, Inc. 1980). Underground mining produced 40 percent of the 7.5 x 10" kg. (830,000,000 tons) of U. S. coal mined in 1980 (Keystone, 1981). There are approximately 70,000 abandoned or inactive underground coal mines in the United States and approximately 2000 active underground coal mines (NAS/NAE, 1975). Underground coal mining in the United States will eventually extend beneath 162 x 109m2 (40 million acres). Thirty-two billion m2 (8 million acres) are already undermined (HRB Singer, 1977). Subsidence due to mining has affected more than 8 x 109m2 (2 million acres) in 30 states, 7.7 x 10 9m2 (1.9 million acres) from bituminous coal mining and the remainder primarily from anthracite mining (Johnson and Hiller, 1979). Subsidence from all other underground mines has affected only 6.9 x 10 7m2 (17,000 acres) (Johnson and Miller, 1979). Subsidence appears to be particularly widespread in two states, Pennsylvania and Illinois, although serious subsidence is found in localized areas of numerous other states (HRB- Singer, Inc. 1977). Host underground coal mining has occurred in the eastern United States, where the U. S. Bureau of Mines estimates 1.6 x 109m2 (398,600 acres) in urban areas in 18 states (out of a total 1.7 x 109m2 1418,400 acres]) are threatened by subsidence (Table 1) (Johnson and Miller, 1979). Pennsylvania and West Virginia contain 57 percent of the total threatened areas. The U.S. Bureau of Mines estimates the total cost to stabilize the estimated 1.7 x lo9m2 (418,400 acres) of subsidence prone urban land located above abandoned mines is over $12.5 billion (1978 costs).

Jan 1, 1982

By E. R. Palowitch, P. H. Broussard

The United States aims to achieve some modicum of energy self-sufficiency through means such as conservation, increased domestic oil and gas production, substitution by the electric utilities of coal or coaloil mixtures for oil and gas, and development of a viable synthetic liquid fuels industry. Coal's role in attaining this goal will necessitate doubling coal production by the end of the 1980's. And if the United States does in fact become the World's Saudi Arabia of coal, the total annual production to meet these domestic needs and export markets could double again by the year 2,000. As only a small portion of our Nation's reserves are recoverable by state-of-the-art surface mining methods, most of the coal produced in the future will have to be mined underground (Averitt, 1975). But this projected increase in coal demand is occurring in the face of a decade of radically decreasing productivity. Specifically, average worker productivity in underground coal mines has decreased from 14.2 tonnes (metric tons) per workershift in 1969 to 7.2 tonnes per worker-shift in 1979; and 95 percent of coal produced underground during this period was produced by room-and-pillar methods (U.S. Dept. of Energy, 1980). Although there is no complete agreement on the impact of recent Federal legislation, there is strong correlation between the dramatic decrease in productivity in underground coal mining and the implementation of the recent Federal mine health and safety regulations (U.S. Congress, 1969). A review of the wide range of coal mining research, development, and demonstration projects currently being funded by the federal government and by industry gives little encouragement for increasing worker productivity on room-and-pillar sections underground in the immediate future (Palowitch, 1978). Conversely, the opportunities for increasing production/productivity underground with longwall methods appear somewhat more encouraging. Although at least one longwall face in the U.S. did produce more than one million tonnes of coal in a single year, the national two-shift average production from one hundred or so longwall faces is about 1,000 tonnes per day (Huwood-Irwin Co., 1978 and Consolidation Coal Company, 1976). Clearly, there exists some real opportunities for improvement. One of these opportunities is to automate the cutter-loader.

Jan 1, 1981

By E. D. Gardner

Apparently the widespread agitation for the codification of our mining laws has had its effect, and it is quite possible that Congress will take up the question during this present session. The greatest objection to our present statutes pertaining to metalliferous deposits seems to be directed against the law of the apex. Those who are not in favor of changing this law are very far in the minority and they apparently realize that it is useless to urge its retention. Next in importance to the repeal of the law of the apex, seems to be a widespread advocacy for the repeal of the law requiring discovery of mineral before a valid location of a mining claim can be made. To a lesser extent there appears to be a desire to have the law changed so as to allow patent for claims without mineral discoveries. The purpose of this article is to review the arguments in favor of the proposed change of the discovery requirement, to show some of the evils that may be expected to result therefrom, and to consider whether a system may be devised to correct the undesirable features of the present law in this respect and at the same time not expose the mining fraternity and the general public to the evils which would result from the repeal of this fundamental requirement. Under the law as at present framed, the validity of a mining location is dependent upon the fact of discovery of mineral within the boundaries of the land claimed. " * * * but no location of a mining claim shall be made until the discovery of the vein or lode within the limits of the claim located" (Sec. 2,320, U. S. Rev. Stat.). All authorities agree that discovery is the source of the miners' title. Lindley, in his valuable work on Mines (3d Ed., Sec. 335), lays down the rule in part as follows: "Discovery is the initial fact. Without that no right can be acquired. * * * Such discovery must precede the location, or be in advance of intervening rights. The proof of recording and marking a claim will not authorize the court to presume a discovery." As is well stated by the U. S. Supreme Court in Erhard v. Boaro (113 U.S. 536):

Jan 1, 1917

By R. P. Rothwell

About thirty miles north of the city of Belleville (which is situated on a branch of Lake Ontario), and in the township of Marmora, Ontario, there is found a belt of gold-bearing quartz veins, which present geological mineralogical, and economic features of great interest to the profession. The district in which these veins are found is characterized as a rolling country, with low rounded hills of syenitic granite, overlain on the flanks of the hills by Silurian limestones, which lie in nearly horizontal beds, and in some places are so fine in texture as to afford lithographic stone of a fair quality. The gold-bearing veins run north and south through this belt of syenitic granite, and are quartz-filled true fissures, with micaceous or talcoid slates forming the walfs of and horses in the veins. This

Jan 1, 1881

By L. A. Dale, D. A. Dahlstrom

Closed-water circuits are justified today from two standpoints: economical operation and prevention of stream pollution. In today's modern preparation plant, it has been found very desirable to have the plant circulating water maintained at a relatively low solids concentration of around 3%. In so doing, bene-ficiation equipment can operate at a much higher efficiency. However, makeup water requirements would become excessive if the fines were to be removed from the preparation plant by bleeding a 3% solids concentration to a tailings pond. With the ever increasing percentage of —200 mesh coal, clay and slimes in the raw coal, coupled with the creation of these fines within the preparation plant, the need for water conservation for economy reasons becomes even more important. Because of stream pollution laws, tailings ponds have become very costly to operate and maintain, resulting in the necessity of employing an in-plant method of water recovery. Accordingly, the primary system employed in water recovery in the coal preparation plant today consists of a solids concentration device to thicken refuse solids while at the same time producing a sufficiently clarified effluent that can go back to the preparation plant for water reuse. The thickened product is then normally passed to a dewatering device that will produce a handleable solid that can be disposed of

Jan 1, 1965

By S. P. Rothwell

ABOUT thirty miles north of, the city of Belleville (which is situated on a branch of Lake Ontario), and in the township of Marmora, Ontario,: there is found a. belt of gold-bearing quartz veins, which present geological, mineralogical, and economic features of great interest to the profession. The district in which these veins are found is characterized as a rolling country, with low rounded bills of syenitic granite, overlain on the flanks of the hills by Silurian limestones, which lie in nearly horizontal beds, and in some places are so fine in texture as to afford lithographic stone of a fair quality. The gold-bearing veins run north and south through this belt of syenitic granite, and are quartz-filled true fissures, with micaccous or talcoid slates forming the walls of and horses in the veins. This

Jan 1, 1881

By R. J. Brison, W. C. Bleimeister

The International Salt Company has long been interested in finding an efficient process for the removal of impurities from rock salt, and particularly from the rock salt produced at the Detroit mine. Methods which have been used previously at the Detroit mine included both hand sorting and differential crushing in a Bradford breaker with rejection of the oversize. Neither of these methods was adequately effective. The development of a new process for removal of impurities from rock salt has been described in the preceding article." Basically, the process consists of exposure of crude rock salt to radiant heating which selectively heats the impure particles. Subsequently the heated particles are removed by adhesion to a heat sensitive-coating on a conveyor belt. This method was found to be effective in improving both the quality and appearance of rock salt by the rejection of the dark, impure particles.

Jan 8, 1960

By A. Boltax

Precipitation processes occurring during both furnace cooling and aging of copper-iron albys were studied by means of electrical and magnetic measurements. On furnace cooling, two distinct stages in the precipitation process were detected; one occurring above and the other below 850° C. The kinetics of precipitation from quenched alloys were studied between 200° and 700°C. The reaction appears to be consistent with the concept of tmcleation of precipitate particles at dislocation loops formed by the clustering of quenched-in vacancies. A study Of in copper-iron alloys is particularly interesting because the combination of magnetic and electrical properties in these allovs provides a quantitative means of following the course of the precipitation reaction. (The details of precip-

Jan 1, 1961

By E. R. Shorey

FLOTATION-Mill operator's have recognized that slimes are detri-mental to the flotation concentration of zinc ores. The, presence of primary slime in many of the Wisconsin ores is largely responsible for the failures experienced in treating these ores by flotation. These failures have discouraged the adoption-of the flotation process by opera-tors in the Wisconsin zinc district. The removal of slimes by decantation seemed to be the obvious way to meet the problem of treating slimy or' clayey ores by flotation. To facilitate the removal of slime, it was decided to mix the ore pulp with sodium silicate, which acts to deflocculate the pulp.1 Deflocculation causes slime suspension, making it possible to separate the slime from the sands by decantation.2 Since the literature contains little definite information on the use of sodium silicate to deflocculate ore pulps, a series of tests was conducted to obtain the necessary information. Tests to determine the settling rates of sand and slime in deflocculated pulps were conducted on a dolomite-marcasite-sphalerite ore ground to minus 80 mesh (175 microns) and mixed with water to form a pulp. The deflocculator3 was Mallinckrodt 40° to 42.5° Bé. liquid sodium silicate (Na20 + 3.25Si02). .By microscopic analysis the suspended slimes4 were found to be minus 15 microns (approximately 1000 mesh).

Jan 1, 1934

By E. S. Leaver

THE presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent. of cyanide-soluble copper and the effect of zinc in the cyanide solution. PART 1.-COPPER IN CYANIDATION The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent. of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust.

Jan 1, 1929

By Robert D. Thomson

LISTED among strategic and critical minerals for stockpiling, mica is an important raw material in electronic and electrical equipment industries. Each year large quantities are consumed in the manufacture of television and radio tubes, radar sets, generators, transformers, electric toasters, and irons. Crude mica, which comes from the mine in crystals or in rough books of various shapes and sizes, is known as run-of-mine or book mica. Structural imperfections, impurities, rough edges, and defective laminae are removed by cobbing, rifting, and trimming to produce a marketable block mica or film mica.' After the rough books have been hand-cobbed to remove adhering rock, dirt, and crushed or defective mica they are rifted, or split. In the U.S. a straight-bladed knife is generally used for rifting. Products of this operation are classed broadly as untrimmed sheet mica and scrap. Sheet mica is any relatively flat piece sufficiently free from physical defects to be cut or stamped into specified shapes for industrial use. Sheet mica is classed as block, film, and splittings. Block mica is not less than 0.007 in. thick with a minimum usable area of 1 sq in. Film mica is split from the better qualities of block mica to groups of specified thickness ranging from 0.0012 to 0.004 in. Splittings are sheets with maximum thickness of 0.0012 in. and minimum usable area of 3/4 sq in. As virtually no mica splittings are produced in the U.S., they will not be discussed in this report. Small, low quality block is subdivided as punch and washer. Punch mica is thumb-trimmed material large enough to yield a circular disk of at least 11/2 in. diam for stained quality mica and 1 1/4 to 2 in. for clear quality. Poorer lots, often referred to as washer mica, are also included in the general term punch mica. Trimming, the next step in processing sheet mica, removes broken and ragged edges, loose scales, and other major imperfections. Trimming may be done with a knife, sickle, shears, or fingers. In the U.S. it is usually done with a 3-in. linoleum knife to obtain a bevel-edged cut. If ragged edges are broken off with the thumb and fingers, the mica is called thumb-trimmed. Full-trimmed is rifted mica trimmed on all sides with all cracks, reeves, and

Jan 1, 1957

By D. Hanson

Fox most of their practical applications metals are required to with-stand stresses of appreciable magnitude: indeed, it is because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances-or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

By F. P. Dewey

The subject of this paper does not embrace the consideration of ways and means for the increase of analytical accuracy, or the question what could or should be attained in that direction. I desire simply to call attention to the degree of accuracy exhibited in actual every-day practice. In estimating this, little weight will be given to the evidence afforded by the agreement of duplicate or multiple determinations by the same chemist; for I am convinced that such agreement is a delusion and a snare. Nor will special importance be attached to the agreement of two or even three analyses in special cases, or to the agreement between two methods practiced by the same analyst. I propose to compare the results obtained by several chemists, working upon the same sample and by various methods, in order to exhibit, as I have said, the actual condition of practice. The available material for illustrating this phase of the question is unfortunately scanty; but something has been done; and I hope, by calling attention to some of the work in this line, to stimulate further work in the same direction by inducing others to prepare suitable samples and submit them to various chemists who are competent and willing to make the necessary determinations, and fully describe the methods they employ. I draw most of my illustrations from the Transactions of the Institute, the Proceedings of the Association of Official Agricultural Chemists, and from personal experience. Manganese in Steel.—In May, 1881, Mr. William Kent presented a paper to the Institute entitled " Manganese Deter-

Jan 1, 1897

By P. E. Hopkins

Introduction and History IN speaking of the economic geology of southeastern Ontario, W. G. Miller and C. W. Knight' say that "there occurs in southeastern Ontario a variety of minerals and rocks of economic value, probably as great as in any district of like size on the North American continent. Some of these deposits, including marble and trap, are inexhaustible. Others, including talc and iron pyrites, have proved to be of considerable economic importance. From time to time, during the last 50 years, the following minerals and rocks have been mined or quarried with varying success: gold, iron pyrites, zinc blende, copper pyrites, galena, mispickel, magnetite, hematite, talc, actinolite, mica, marble, ophicalcite, feldspar; fluorite, apatite, corundum, graphite and sodalite. All of the economic materials, with the exception of fluorite, appear to be of pre-Cambrian age. The fluorite veins penetrate the Ordovician, Black River, limestone." Accompanying that report was an article by the writer on the Queensboro Pyrite Area which includes one of the two working pyrite properties in southeastern Ontario. In the present paper will be given a brief description' of all the known pyrite deposits in the area which may at some time possess an economic value, with fuller descriptions of the two working mines-The Canadian Sulphur Ore Co.'s mine near Queensboro, and the Nichols Chemical Co.'s property at Sulphide. The earliest mining of iron pyrites in Ontario was done in 1868 on the Billings property near Brockville. The mines were closed down in 1879 under the assumption that they were exhausted. Many other

Jan 8, 1916

Dr. F. W. C. Schniewind, New York, N. Y.:—Mr. Vogel speaks of briquetting the flue-dust by means of lime. I learned recently in Europe of a process employed with considerable success at one of the blast-furnaces, where blast-furnace cinder is used with lime. The lime and cinder are mixed with the flue-dust, and exposed to superheated steam, which converts the blast-furnace cinder into cement. Briquettes are then formed in the usual way. Mr. Vogel :—The process referred to is the " Scoria process," which has not been in use for some time past. For that reason, I did not mention it. Prof. Arthur L. Walker, New York, N. Y.:—I would ask the commercial name for magnesium chloride, and where it can be obtained ? Mr. VoGel :—I mentioned magnesium chloride, because it has been used abroad to a large extent. In Germany it is obtained as a by-product in the manufacture of potash-salts; in the United States we have been using chloride of lime, which is cheaper. Otto Sussman, New York, N. Y.:—What is the cost of this process ? Mr. Vogel :—The cost is exceedingly low. I can give you the figures from abroad, but not for the United States, because the system has not -yet been used here commercially to

Jan 1, 1913

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953