Search Documents

By William B. Millar

IN ONTARIO development of the gold mines is being rapidly pushed, while the intensity of the search for new mines has probably not been equaled at any time in the past. Even to outline the results of recent prospecting activity in Ontario would be a big undertaking, but it would be timely and, I hope, interesting to Institute members to review some generalities regarding the work of the prospector and then to discuss in some detail the growth of Ontario's most promising prospect area, the Swayze district, where serious mining operations are already under way. Probably no one writing about prospectors and pros¬pecting can resist hoping that his article will not reach the eyes of a certain portion of the uninformed general public and cause a further influx of "prospective prospectors" into any given area. It is somewhat mystifying how so many people reach the conclusion that prospecting is in

Jan 1, 1933

By Tong Guangxu

INTRODUCTION Throughout the world, the caving mining methods of ore-draw under the overlying waste rock are sublevel caving in Sweden, block caving in U.S.A. and forced block caving and sublevel caving with sill-pillar in U.S.S.R. These caving methods are of high efficiency, low cost and large production (especially the block caving method) when compared to opencast mining. From the ore production of all under- ground mines, the largest annual production of underground metalliferous mines in the world is caving methods. The sublevel caving in Kiruna Iron Mine of Sweden has reached annual ore production over 20 million tons in 1974. The block caving in Climax Molybdenum Mine and San Manuel Copper Mine of U.S.A. both have produced about 40 thou- sand tons of ore per day in 1971. At the same time, the productivity of Kiruna was 12 thousand tons of ore per man-year, Climax 42.8 tons (48.3 short tons) per man-shift and San Manuel 29.01 tons (32.1 short tons) per man-shift. The main feature of this group of mining methods is the underground extraction of ore from beneath overlying caveable waste rock. Since the loss and dilution of ore are inherent (sometimes to a great extent), the control of ore-draw in these methods as com- pared with other methods is very important. Consequently, concerned Universities and Research Institutes have devoted great amounts of research on ore-draw theory and control management which has provided positive results to mine production, and has apparently promoted the development of the caving methods. During 1979 in China, metalliferous underground mines accounted for 15.22% of the total iron ore produced, while also accounting for 56% of total non-ferrous production. According to the mining methods, sub level caving in the principal underground iron mines counted for about 56.74% of total principal underground iron mine production, but only about 1% of total non-ferrous underground mine production. Relative to forced block caving and sublevel caving with sill pillar, the Chinese non-ferrous under- ground mines estimated about 35% of total non-ferrous underground mine production from these two methods, mainly from the latter. From the trend of development of underground metalliferous mines in China, the percentage of production in caving will be increased in the future, especially in block caving and forced block caving which have already been given great attention in the mining circle. In these types of mining methods the ore is drawn from the stope under a large area of overlying waste rock, which complicates the basic regulation and control of ore-draw, but provides lower loss and dilution than sublevel caving. Because of these reasons, the Kiruna Iron Mine in Sweden is intending to change its sublevel caving by testing a sublevel shrinkage caving method and considering a large area of ore-draw beneath the stope as an advantage. Therefore, the basic regulation and control management of ore-draw under a large area, as practiced in China, will be discussed in this paper. BASIC REGULATION OF ORE- DRAW FROM CAVING STOPE The aim of studying ore-draw under a large area of overlying waste rock is to se- cure a planned draw schedule that guarantees a certain plane of interface between ore and waste rock, and controls the change of its shape in spatial position for reducing ore loss and dilution during the draw process. Presently, the ellipsoid theory is comparatively near the actual attitude of ore-draw from the cave. 1. Ore Drawn Out from Single Drawpoint Laboratory testing and practical experience all show that after a certain amount of ore has been drawn out from a drawpoint, its original shape in the stope before drawing is more or less similar to an ellipsoid, hence the name "draw ellipsoid." This draw ellipsoid is cut at the bottom by a horizontal plane corresponding to the raise of the drawpoint, and its volume can be calculated by the following formula:

Jan 1, 1981

By DOOLITTLE E. M.

(Canal Zone Meeting, November, 1910.) The following notes are contributed, not with the idea of offering a complete history of the development of this very important process as applied to the Leadville district, but with the hope that the practice, as it was carried out in the Bi-Metallic Smelter, may still be of interest to others. The Bi-Metallic Smelter, at Leadville, Colo., was the first to make a commercial success of the process described in the following pages, which consisted essentially of smelting raw silver- and copper-bearing sulphide ores in blast-furnaces to form a matte, which was generally re-smelted with siliceous ores for a second high-grade matte. Robert Sticht, in his excellent monograph on the subject,1 has outlined briefly the plant belonging to this company. He says, in effect: The Boulder, Mont., enterprise set the example for others with whom the patentee (w. L. Austin) had been negotiating, and the old La Plata lead-smelter at Leadville, Colo., was fashioned into a crude, temporary experimental plant for the Bi-Metallic Company, and the feasibility of the process demonstrated by a trial run. Subsequently, the plant was considerably improved, and, being supplied with very favorable ores, continued to run without interruption from August, 1892, to June, 1893. In September, 1893, smelting was resumed in a completely remodeled establishment, some $200,000 having been expended upon the new work. Thus, aside from the Montana experiments, which, under the direction of W. L. Austin, began as early as- 1885 2 at Toston, and continued with indifferent success for six or seven years, the Bi-Metallic plant at Leadville may be said to have * Formerly Superintendent, Bi-Metallic Smelting Co. + Formerly Chief Assayer and Chemist, Bi-Metallic Smelting Co. 1 Modern Copper Smelting, E. D. Peters, 7th ed., p. 415 (1895). 2 Trans., xvi., p. 259 (1887-88).

Dec 1, 1910

By D. A. Vaughan

COMPOUNDS in the U-N system have received little attention since the work of Rundle, Baen-ziger, Wilson, and McDonald in 1948.' They described the three nitrides UN2, U2,N2, and UN as the only phases in this system. The region between UN and U,N, was reported to consist of the two phases while the region between U,N, and UN, is a homogeneous solid solution in which the U,N3, structure transforms with increasing nitrogen content into the UN, structure. This report presents the results of an X-ray diffraction study of the phases present in the region of the diffusion gradient on uranium reacted with nitrogen at several temperatures between 500" and 915°C. Several samples of uranium used in U-N gas-metal reactions by Mallett and Gerds were available for X-ray diffraction study of phase composition through the diffusion gradient. X-ray diffraction data were obtained using filtered iron radiation at intervals through the diffusion layer of the several samples on filings or turnings at approximately 0.001 in. increments down to the base metal. Representative X-ray diffraction patterns from various layers through the case on uranium after nitriding at 850°C are shown in Fig. 1. These data show that three different phases are present in the

Jan 1, 1957

By E. J. Eisenach, Edward Matsen

AT the present time the Climax Molybdenum Co. is the largest molybdenum producer in the world and the operator of the largest underground mine in North America. It has grown steadily and rapidly since its beginning in 1917. Only 250,000 lb of MoS2 were produced during the first year from 1917 to 1918 when the company was formed. Operations were suspended shortly thereafter because of the lack of a market and knowledge of the uses of molybdenum. During World War I it was used as a substitute for some rare metals and for minor chemical purposes. After 5 years of intensive research and sales promotion, Climax metallurgists succeeded in finding proper applications for the newly discovered metal and the mine was reopened in 1924. Demand for molybdenum increased gradually and in 1930, 3.5 million lb of MoS2 were produced. In the meantime, research work for additional uses of molybdenum continued until it had established itself as one of the most important alloying elements in producing high quality steels. After the start of World War 11, from January 1942 to October 1953, 43 million tons of molybdenum ore were mined and 484 million lb of MoS2 were produced. Climax mine is located in Colorado, 100 miles southwest of Denver and 12 miles northeast of Leadville on the Continental Divide of the Rocky Mountains. The principal mine workings range from 11,170 to 12,000 ft in elevation. Topographically, it lies in the base of a large cirque that is surrounded by Mt. Bartlett to the north, Clinton Peak and McNamee Peak to the east and Ceresco Ridge to the south. This cirque opens to the west and to the Ten Mile Valley.

Jan 3, 1954

By M. C. Manderson

Abstract-The sharp drop in world phosphate demand that took place in 1975, due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had previously been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1978

By M. S. Tsai, Y. D. Chuang, H. M. Wu

To contact the commercial OPAP-kerosene solution with CH3OH – H20 solution, we used the appropriate concentration of DOPAP / MOPAP solvent. By using this treated OPAP solvent, uranium can be recovered from wet-process phosphoric acid. Electric DC power is supplied on the dual side of the ion-exchange membrane of a specially designed box-type mixer settler. U(VI) is reduced to U(IV) in the cathode and U(IV) is oxidized to U(VI) in the anode. Uranium is extracted in the cathode by treating it with OPAP solvent. Next the uranium is stripped from the loaded OPAP solvent by concentrated phosphoric acid in the anode. After 300 hours of continuous operation total recovery of uranium is as much as 95%.

Jan 1, 1984

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By John R. Don

In the South Island of New Zealand an unusually favorable opportunity is offered for the analysis of the older crystalline rocks, underlying the sedimentary rocks which form the "country" of the gold-deposits. The Manipori formation of this island, comprising the greater part of the mountainous district west of lakes Manipori and Te Anau, in Otago, consists of an enormous thickness (estimated by Professor Hutton1 at 160,000 ft.) of crystalline schists, gneiss, syenite, and syenitic gneiss, with associated masses of granite; the whole forming the most picturesque fart of New Zealand. The famous West Coast sounds occur in this formation. No paying auriferous lodes have been discovered in it; and for this reason an examination of the rocks is specially interesting here. Stelzner, Posepny, and others, who have criticised the conclusions of Sandberger, have laid great stress on the fact that all the silicates analyzed by him were taken from the vicinity of orebodies containing those heavy metals which he notes as occurring in the silicates of the country-rock; their contention being that these metals, supposed to occur as silicates in gneiss and other crystalline rocks, were really contained as sulphides, and were therefore impregnations from the neighboring orebodies. The same objection, whatever be its weight, might be urged with equal justice against Mr. Becker's derivation of the mercury and gold of the lodes of the Pacific Coast from' the granite underlying their country-rock. In the case of the

Jan 1, 1913

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

By John B. Hastings

The origin of the watery vapors of vulcanism has always been an object of interest and speculation to the seismologist, and as theories of the genetic origin of ore-deposits have of late years been pretty well narrowed down to the expiring forces of plutonic action, the same question has attracted mining engineers and geologists, as is well shown by the discussions of the subject in our Transactions. The important part taken by volcanic emanations in the origin of pegmatites and quartz-veins, described in my paper, Origin of Pegmatite,' and their latent power to concentrate into useful deposits such scattered gold as occurs in the Hartsel granite, make a discussion of their derivation but a natural third and final step. It is coilceded that enormous amounts of vapor accompany vulcanism, though perhaps we are apt to forget that steam has 1,700 times the volume of water, besides which the column seen over Vesuvius and other volcanoes is greatly mixed with air; the immensity of such volumes compared with solids and liquids is shown by the experiment of Gautier, who, by heating dessicated granite to 100' C., evolved from it gases 20 times, and steam 90 times, its own volume. Dana appraised the average amount of water left in ordinary rocks as 2.5 per cent. T. M. Read estimated that the Mississippi river carries to the sea annually 150,000,000 tons of rock material. If these Mississippi sediments, as deposited, contained 20 per cent. of water, it would be 600,000,000 cu. ft., or 4,500,000,000 American gallons, annually. Allowing the vapor suspended over a volcanic cone to be mixed with 80 per cent. of air, this amount of water converted into steam would replenish anew, every 9 min., a column 15,000 ft. high, 2,000 ft. in diameter at the base, and • 10,000 ft. at the top. Read's estimate is only half of the amount given in a more recent and probably correct one.2

Jan 1, 1909

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By R. W. Fountain, J. Chipman

THE solubility of nitrogen in iron and steel has been of considerable interest due to the role of nitrogen in strain-aging and in quench-aging. It is generally considered that quench-aging is the result of precipitation of carbide and nitride particles from supersaturated solid solution, while strain-aging results from the segregation of carbon and nitrogen atoms to dislocations.1-9 The rate of strain-aging is controlled primarily by the amount of carbon and nitrogen in solution and the temperature. In experiments on strain-aging of pure iron with only carbon or nitrogen as impurities, Fast" has shown that even after 40 hr at 50°C carbon did not give any strain-aging while

Jan 1, 1959

By David B. Reger

The expansion of the previously discovered gas pools and an intensified search for additional pools in the Oriskany and deeper sands were the principal petroleum activities in West Virginia during 1941. One small oil pool was discovered and another was considerably extended. One small gas pool was discovered, several isolated well discoveries were expanded into definite pools, and various recognized pools were substantially increased. The proved oil territory of the state was increased about 600 acres and the proved gas territory about 45,000 acres. The new discoveries of oil did not equal withdrawals but gas reserves added were greater than gas withdrawals. Oil activity, as in the past several years, was slight because of unfavorable crude prices. Most operators prefer to leave oil in the ground rather than to drill for it without a better return. Gas activity increased greatly because of better demand, even though the price of gas did not improve. The account of operations, as gathered from trade journals and other reporting services, shows that 838 new wells were drilled, resulting in 114 new oil wells with 2606 bbl. of daily new production; 558 new gas wells with 949,226,000 cu. ft. of daily open flow; and 166 dry holes. Also, 86 old wells were drilled to deeper sands with 9 bbl. and 56,030,000 cu. ft. of added production. On the new wells the oil average was 22.86 bbl. per well per day; and the gas average was 1,701,000 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 13.61 per cent. On deeper drilling to other sands the ratio of failures was 15.12 per cent. From an exploratory standpoint one strictly new oil pool (Higginbotham Run) was opened in Kanawha County and one strictly new gas pool (Lost Run) in Taylor County. One entirely isolated wildcat gave commercial Oriskany-sand gas production and may open a pool. Various other wildcats greatly extended the boundaries of known Oriskany-sand gas pools and various others may have opened new pools in the shallow sands. On the other hand, various Oriskany tests in Harrison, Monongalia, Roane and Wood Counties were dry and all five tests to the White Clinton sand (Sil.) in Boone, Harrison, Kanawha and Wood Counties failed to find commercial production. The principal oil wells completed, by counties, were: Calhoun, 24; Clay, 7; Gilmer, 6; Hancock, 9; Kanawha, 9; Pleasants, 10; and Ritchie, 14. Production for the year was estimated by the Oil Weekly as 3,421,000 bbl., compared with U. S. Bureau of Mines final figures of 3,444,000 bbl. in 1940. The leading counties in gas-well completions were: Boone, 32; Braxton, 19; Cabell, 16; Calhoun, 46; Clay, 20; Gilmer, 37; Jackson, 94; Kanawha, 82; Lincoln, 17; Putnam, 46; Ritchie, 33; Upshur, 20; and Wayne, 33. Production for the year is estimated by the author as 210,000,000,000 cu. ft., as compared to the U. S. Bureau of Mines' final figures of 188,751,000,000 cu. ft.* in 1940.

Jan 1, 1942

By David B. Reger

The expansion of the previously discovered gas pools and an intensified search for additional pools in the Oriskany and deeper sands were the principal petroleum activities in West Virginia during 1941. One small oil pool was discovered and another was considerably extended. One small gas pool was discovered, several isolated well discoveries were expanded into definite pools, and various recognized pools were substantially increased. The proved oil territory of the state was increased about 600 acres and the proved gas territory about 45,000 acres. The new discoveries of oil did not equal withdrawals but gas reserves added were greater than gas withdrawals. Oil activity, as in the past several years, was slight because of unfavorable crude prices. Most operators prefer to leave oil in the ground rather than to drill for it without a better return. Gas activity increased greatly because of better demand, even though the price of gas did not improve. The account of operations, as gathered from trade journals and other reporting services, shows that 838 new wells were drilled, resulting in 114 new oil wells with 2606 bbl. of daily new production; 558 new gas wells with 949,226,000 cu. ft. of daily open flow; and 166 dry holes. Also, 86 old wells were drilled to deeper sands with 9 bbl. and 56,030,000 cu. ft. of added production. On the new wells the oil average was 22.86 bbl. per well per day; and the gas average was 1,701,000 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 13.61 per cent. On deeper drilling to other sands the ratio of failures was 15.12 per cent. From an exploratory standpoint one strictly new oil pool (Higginbotham Run) was opened in Kanawha County and one strictly new gas pool (Lost Run) in Taylor County. One entirely isolated wildcat gave commercial Oriskany-sand gas production and may open a pool. Various other wildcats greatly extended the boundaries of known Oriskany-sand gas pools and various others may have opened new pools in the shallow sands. On the other hand, various Oriskany tests in Harrison, Monongalia, Roane and Wood Counties were dry and all five tests to the White Clinton sand (Sil.) in Boone, Harrison, Kanawha and Wood Counties failed to find commercial production. The principal oil wells completed, by counties, were: Calhoun, 24; Clay, 7; Gilmer, 6; Hancock, 9; Kanawha, 9; Pleasants, 10; and Ritchie, 14. Production for the year was estimated by the Oil Weekly as 3,421,000 bbl., compared with U. S. Bureau of Mines final figures of 3,444,000 bbl. in 1940. The leading counties in gas-well completions were: Boone, 32; Braxton, 19; Cabell, 16; Calhoun, 46; Clay, 20; Gilmer, 37; Jackson, 94; Kanawha, 82; Lincoln, 17; Putnam, 46; Ritchie, 33; Upshur, 20; and Wayne, 33. Production for the year is estimated by the author as 210,000,000,000 cu. ft., as compared to the U. S. Bureau of Mines' final figures of 188,751,000,000 cu. ft.* in 1940.

Jan 1, 1942

By Claus G. Goetzel

PRESSING of powdered metal parts is best done in the direction of the shortest extension of the piece, to avoid too great a loss of pressing force through internal [ ] friction. As long as curved surfaces, recesses, or offsets occur only parallel to this shortest axis of pressure, no special difficulties arise: the cross sections, perpendicular to the pressure, do not vary, nor does the shape of the parts change during compression except for a gradually reduced thickness (Fig. IA). The problem becomes more difficult, however, when the curved surfaces or recesses are perpendicular to the shortest axis of the part (Fig. IB). Two processes for molding uniformly dense parts with complicated shapes from powdered metals are described in detail in this paper. Both can be employed successfully by those trained in the art. The first refers to curved parts; the second is especially adapted to parts having one or more recesses or steps. Both methods, as set forth here, are applied under the condition that presents the more difficult problem. For clarity, before description of the two practical methods, the variable factors in molding powdered metal parts will be reviewed, then an idealized procedure will be considered briefly. VARIABLE FACTORS IN MOLDING POWDERED METAL PARTS Compression Ratio Compression ratio is defined as the proportion of the final relative density of the compact to the apparent density of the powder. For iron powder of an apparent density of 3.0, for example, a compression ratio of 2 1/2 : I would be required to produce a compressed compact of 7.5 density; whereas for another iron powder having an apparent density of only I.5, a compression ratio of 5:I would be required to produce the same density. The lower the powder's apparent density, the greater must be the compression ratio for pressing compacts of high density.

Jan 1, 1945

Secretary's Note.—M. Beutter's introductory remarks, being simply a resume of Prof. Hone's paper, with a disclaimer of the intention to criticise it, have been omitted, and the remainder of this contribution lias been somewhat condensed, without omitting any essential statements. M. Beutter, St. Etienne, France* (communication to the Secretary†):—Professor Home observes in $ 47 of his paper that the fluid-compression of steel diminishes piping by forcing the liquid and viscous metal, while the pipe is forming, or after it has formed, into the space so produced, and proceeds to study the different systems of compression, alluding to the four principal ones: Whitworth, Illingmorth, Williams, and Harmet. Having now for many years had in use the last-named process, that of M. Henri Harmet, I shall attempt to explain the difference between it and the three other processes named. The Harmet process does not diminish or close the pipe after it has formed, but prevents it from forming; and I may add that it is the only one of the four which produces this result. It is true that the Whitworth process diminishes the interior hollow by localizing it around the central axis of the ingot, which is afterwards removed by trepanning the hollow forg-ings for which this process has been, I believe, always exclusively used. The Illingworth and Williams processes, which, in my opinion, are applicable only to small ingots, of necessity allow the pipe to form, or (to use the expression of Professor Howe) they allow the surface of the lake of liquid steel to sink into the interior of the ingot, since they involve waiting a certain time before compression, so that (in the case of the Williams process) the ingot-mold can be opened without danger, or (in the case of the Illingworth process) so as to avoid the risk that the steel may enter the grooves produced by the removal of the distance-bars. During the time required for

Jan 1, 1908

By C. W. Ryan

THIS paper contains a brief sketch of the geology of soapstone in the Piedmont section of Virginia, in the southern portion of Nelson County; also a description of methods of prospecting, developing quarries, quarrying and and milling methods in that section. The paper is intended for those who have little information regarding soapstone; undoubtedly men of practical experience will find many points for criticism.

Jan 1, 1929

By G. C. Hancock

The operating plant of The Broken Hill Associated Smelters Pty. Ltd. is situated at Port Pirie in South Australia and it treats to finality the whole output of lead concentrates from the mines of The Zinc Corporation Ltd., North Broken Hill Ltd., and aroken Hill South Ltd. at Broken Hill, New South Wales. Lead bearing ores from other sources are also purchased for treatment and lead scrap and residues are treated on a toll charge basis. The present output of the plant is approximately 200000 tonnes of refined lead per annum and there is a substantial production of by-products including refined silver, gold, cadmium, antimonial lead alloys, copper matte and sulphuric acid. Recently the Company commenced the production of zinc by slag fuming and electrolysis from a six million ton dump of lead blast furnace slag, which has been accumulating at Port Pirie for over fifty years. The slag fuming plant contains two furnaces of conventional design, but features a high degree of pre-heat for the blast air and this is obtained by the use of all-metal recuperators. The raw zinc oxide fume produced by the plant is roasted in a rotary kiln prior to treatment in the leaching and electrolysis sections, which follow conventional practice for nigh current density plants. Present output is approximately 36000 tonnes of electrolytic zinc per annum.

Jan 1, 1970