Search Documents

George A. Packard, Boston, Mass. (communication to the Secretary†):—The very interesting results obtained by Prof. Hofman and his assistants came to my attention when I had temporarily assumed charge of the metallurgical department of the Missouri School of Mines, and had found it, pending the completion of a new building, lacking a furnace in which to roast ore preparatory to the customary lead blast-furnace run. An attempt at lime-roasting had been already determined upon, but the use of a charge which would make a slag of definite composition was a new idea. The results following were obtained by Messrs. Aubrey Fellows, J. C. Long, E. R. Wash, and Dr. T. C. Tseung, under my supervision. It is regretted that the data are not more complete; but the work was done simply incidentally to securing the desired ore for the blast-

Jan 1, 1908

Bernard MacDonald, Guanajuato, Mexico (communication to the Secretary*):—Mr. Iceyes's paper is very interesting to me because of my personal experience with the development of the ore-deposits of Lake Valley.

Jan 1, 1909

By C. M. Brinckerhoff

Safety work in mining at the Andes Copper Mining Company, Potrerillos, Chile, is divided into three parts: (1) accident prevention, (2) fire prevention and protection, and (3) silicosis prevention and control. In the company's operations a steady campaign has been waged to reduce accidents and silicosis, and to prevent fires. In the following pages the safety record for the past twelve years will be examined and the methods explained by which the accident rate was reduced. Table 1 contains yearly data pertaining to the scale of the mining operations and the accident record. Block caving is used for all ore production and the tonnage mined has averaged 30,000 short tons per day for the past seven years. Table 2 classifies 44 fatal accidents which have occurred since 1935. The leading causes of accidental death are transportation of ore and use of explosives, followed in order by persons falling, falls of ground, and by asphyxiation. In the case of serious accidents, however, the greatest cause is falls of ground, followed, in turn, by ore transportation, persons falling, explosives, and asphyxiation. Accident Prevention The improvement of the safety record was obtained by a combination of many factors. In surveying the results at Andes for the past twelve years, it is possible to select some features of the present operation which have contributed to the accident record. The most important of these are: (1) good staff planning, (2) good equipment, (3) an alert safety organization, and (4) education and selection of the workmen. GOOD STAFF PLANNING As a result of good staff planning, the mine has good working conditions, namely, good ventilation, moderate temperatures and humidity, and good lighting. These factors not only reduce accidents but also improve efficiency. In haulage work, accidents have been reduced by having traffic move in a forward direction only. The latter makes possible a one-man train crew. Trains are centrally dispatched from loading drifts which are interconnected by signal lights, so that when a train in a lateral drift is given permission to move into a main line drift, a red light signals in all other lateral drifts in that area. Good track is maintained, and safety niches are required at all switch throws. Since safety niches were provided there have been no fatal or serious accidents at such points. All main line haulage drifts are illuminated by electric lights. Haulage drifts are kept clean. Adequate clearance has been provided between cars and between cars and the sides of the haulage drifts. The 4 1/2 ton Cranby type cars are equipped with roller bearings, and the 10 ton loconlotives with trolley shoes instead of wheels. These two features are responsible for improved ore haulage conditions and contribute to greater efficiency and safety.

Jan 1, 1950

D. M. Riordan has been appointed a member of the Institute Com¬mittee of the Engineers' Reserve Corps movement. Our Committee, therefore, now consists of Henry S. Drinker, Chairman, Messrs. Arthur S. Dwight, Warren A. Wilbur and D. M. Riordan.

Jan 1, 1916

By G. A. Beske, P. Hilsch, J. Wulff

The effects of the growth precipitates on the su-perconduching properties of an Al- 15 al. pel Zu alloy have been studied using magneization, transition lem-perature, and residual resistivity measurements. Aging at 230C for 1/2 to 11 he produces an increase in Hfp, Ike field of first penetration, and tut increase in trapped flux. The upper critical field, Hc2 remains constant for such aging tunes. Aging at 200°C produces a decrease in Hfp and an increase in trapped flux. The transition temperature remains constant at Tc - 1.227° ± 0.02°K for aging at 220°C for tims of from 1/2 to 10 hr, and for aging at 200°C it remains constant at Tc. = 1.18° i 0.02°K for times from 1/2 hv to 26 hr. The observed behavior indicates that the superconducting matrix when aged at 220°C behaves tike a type U su-perconducior, but when aged at 200°C behares like a type I superconductor. The magnetization changes after aging can be attributed to the growth and clutnge in distribution of the precipitate in a matrix of fixed composition. IT has been realized for some time that the superconducting properties of alloys are highly structure-sensitive. This is evident in the work of Mould and Mapother1 who examined the properties of an aluminum alloy. Precipitation effects have also been briefly mentioned in other studies.2-4 Bonnin and coworkers5 have observed a sharp inc rease in trapped flux in an A1-Mg alloy when the residual resistivity reaches a value that indicates it is a type II superconductor. Recently Blanc, Goodman, and Nemoz5p have reported on precipitation effects in A1-Ag alloys. Detailed studies of precipitation in Pb-Sn and Pb-Cd alloys made by Livingston6 serve to show that the upper critical fields are enhanced by quenched-in solute. Furthermore. at various stages in the precipitation process? the upper critical field is determined largely by the remanent solute. The observed magnetic hysteresis and trapped flux in such alloys result from the interaction between precipitate and the flux filaments in the mixed state. The flux trapping appears to depend largely on the precipitate distribution and is greater if the superconductor is type II than if it is type I. To examine the effect of precipitation in another alloy system, particularly one in which the composition of the superconducting phase does not change significantly during the course of precipitation, the Al-Zn system seems interesting, especially in view of the transition temperature and resistivity studies of Chiou and seraphim.' Furthermore, the recent detailed electron-microscope studies of an Al-Zn alloy by Richards and Garwood8 provide a guide for relating superconducting properties to changes in structure. For these reasons, magnetization, transition temperature, and residual resistivity measurements for varying times of heat treatment at two temperatures were made with a -15 at. pct Al-Zn alloy. The results are reported in this paper. I) EXPERIMENTAL The alloy used was prepared by Cominco Products Inc. from 99.9999 A1 and 99.999 Zn. It was chill-cast, swaged, and drawn to 0.125-in.-diam rod. The analyzed composition was 15.6 at. pct Zn (31.1 wt pct). A jeweler's saw was used to cut the 0.125-in.-diam rod into the 0.875-in. lengths needed for magnetization measurements. The ends of the cylinders were slightly beveled to remove the sharp edges. A portion of the original 0.125-in.-diam rod was drawn into 0.010-in.-diam wire and used for transition temperature measurements. Specimens were suspended from wires within a vertical furnace during heat treatment. All were homogenized at 500°C for a minimum of 3 days and subsequently solutionized for times in excess of 6 hr. The solutionizing temperature was held constant to +3°C. Individual specimens were homogenized, quenched, and aged several times and no effects indicating loss of zinc were noted. The suspended specimens were quenched by cutting the wires and allowing the specimens to fall into a silicone oil bath held at the aging temperature. They were then isothermally transforked by aging in the same bath used for quenching. After aging for the required time (approximately 10 min aging was necessary before the upper critical field reached a fixed value), they were briefly (1 to 2 sec) dipped into an acetone bath at room temperature to remove adherent oil and then immediately transferred to liquid nitrogen where they remained until inserted into the helium bath (usually within an hour). The temperature of the aging bath was held constant to +3°C for longer aging times. The cryostat used for the measurement of superconducting properties consisted of outer and inner dewars for liquid nitrogen and liquid helium, Stokes 6-in. booster diffusion pump and Stokes Model 212 mechanical pump, temperature controller to measure and control the temperature of the helium bath, and a superconducting solenoid with inserted search coils to provide the magnetic field and measure the magnetic moment of the specimens. A schematic diagram of the cryostat is shown in Fig. 1. An ultimate temperature of 0.85°K was reached with this apparatus. The temperature controller used is similar to the one described by Blake and chase.' A 0.5 pct Allen-Bradley carbon resistor and a nichronle heater (200

Jan 1, 1968

By AIME AIME

DREAMS do come true at times, although it is evidently better to believe in engineers than to "believe in fairies" if most dreams are to be translated into fact. It was a fine dream that David H. Moffat had when he projected a railway directly west from Denver; a dream of opening a new empire in northwestern Colorado, and of quickening transportation from the Middle West to the Pacific slope. But Moffat had been a miner and had become a banker. He knew that dreams, untranslated into works, benefit no one and pleasure only the dreamer, so he employed an engineer, H. A. Sumner, to study and plan the route to be followed by the rails. Previous main lines had run to the north, the Union Pacific, or the south, the Santa Fe. The Denver and Rio Grande, it is true, wriggled its way bravely across Colorado but, in order to reach a point 74 miles in an airline west of- Denver, travelled 281 miles following two canyons and crossing Tennessee Pass at 10,240 ft. Valuable as such a road is, it could never accomplish what Moffat had in mind. It was known that no low pass could be found directly west of Denver but up to 9000 ft. the topog-

Jan 1, 1925

By D. C. Jackling

I BESPEAK your indulgence for a brief expression of the views of a patriarch in the field of mineral industry technology relative to young men's problems in that sphere of education and endeavor. Wherever hereafter I employ the terms "technical education," "engineer," "technologist," or similar expressions, these are intended to be understood as relating to the broad field of the sciences and arts applicable to the mineral industries. First, the usefulness of technical education to either the possessor of it or those to whom its services may be made available industrially depends primarily upon the quality of the education and the capabilities of the educated to put his talents to effective and constructive employment in his chosen field of applied science.

Jan 1, 1940

By L. E. Shiffman

W. J. Parton—Those operators faced with the problem of treating fine coal whether in bituminous or anthracite will find this paper most timely. I would like to take this opportunity of discussing Mr. Schiffman's paper and at the same time express certain views relating to our Tamaqua plant. I would like to ask the author what type of impeller and diffuser is used in the Denver cells? Screen analysis of products from individual cells indicate that coarser material resists flotation and only floats after greater retention time in the last few cells. Also, the need for a scavenger screen to reclaim non-floated coal particles further stresses this point. I have always felt that more efficient means of cleaning coal between 10-mesh and 28-mesh existed than flotation. Reagent and power costs are high for the flotation process. When floating +28-mesh particles, cell capacity is lowered and some of the particles are lost with the refuse. The Tamaqua plant of the Lehigh Navigation Coal Co. floats —28-mesh coal and capacity of recoverable coal is 40 tph for 1800 cu ft of Denver cells; or 0.05 tons per cu ft of cell. At Kimberly 7.75 tph for 600 cu ft of cell gives 0.013 ton per cu ft of cell. At Bessie 14 tph for 800 cu ft of cell gives 0.017 tons per cu ft of cell. It would be appreciated if the author would comment on what he feels is the upper size limit of particle to attain most efficient utilization of the flotation process. The dewatering screw is a very interesting development since it offers a simple way to prepare coal sludge for more complete clewatering by drainage or mechanical dewatering on screen or filters. In other words it could be used to accomplish the same thing as a thickener tank. I would appreciate having the author's comment on how he thinks such a screw dewaterer would work on a froth.* The process as used in floating coal at the Bessie and Kimberly plants may be referred to as more of a bulk oil float in contrast to a froth flotation process. Experiments on increasing capacity of cells is most interesting since we are going through such an experi- mental period at the present time. Recently a double overflow was installed on our No. 30 Denver cells. So far results are not conclusive. In reviewing this paper the following comments are made pertaining to investigation of methods for increasing capacity: Supercharging: Supercharged air in matte flotation or for that matter the use of the normal amount of air drawn in by the impeller would in all probability cause such an aeration in the cell as to destroy the buoyant effect given to the coal particles by the excessive amount of kerosine used. In other words, air creates an agitation zone throughout the cell, creating a boiling and thereby giving a lower recovery in the cell. It would be interesting to know whether the 7 pct increase in recovery was with no air being admitted to the stand pipe. Changing Impeller Speed: The speed of a receded disc impeller for a No. 30 cell as recommended by the Denver Equipment Co. is, I believe, approximately 250 rpm. At this speed and using supercharged air in excess of 8-oz pressure, we have observed a boiling action in the cells. In our flotation we endeavor to obtain some degree of froth flotation using pine oil as a frother. The boiling action as caused by increasing the amount of air added to the cells is detrimental to recovery in froth flotation. It is our belief that to obtain increased recovery from a cell in froth flotation, additional air must be introduced but at the same time this air must be dispersed throughout the pulp in the form of small bubbles and this can only be done by increasing the speed of the impeller. Therefore, if Mr. Schiffman decreased the speed of the No. 30 impellers and at the same time continued to use supercharged air, the boiling action may have been increased because larger bubbles developed. The lower recovery as reported could be due to this factor. Decreasing the impeller speed will definitely decrease the power consumed but may have other disadvantages. First, we believe it will permit "sanding" in the cell and this in our opinion will increase the wear on the impeller and diffuser, especially so, if there is pyrite and/or sand present in the feed. "Sanding" in the cell when air is used, as in froth flotation, will effect the dispersion of this air and cause boiling.

Jan 1, 1951

By L. E. Shiffman

W. J. Parton—Those operators faced with the problem of treating fine coal whether in bituminous or anthracite will find this paper most timely. I would like to take this opportunity of discussing Mr. Schiffman's paper and at the same time express certain views relating to our Tamaqua plant. I would like to ask the author what type of impeller and diffuser is used in the Denver cells? Screen analysis of products from individual cells indicate that coarser material resists flotation and only floats after greater retention time in the last few cells. Also, the need for a scavenger screen to reclaim non-floated coal particles further stresses this point. I have always felt that more efficient means of cleaning coal between 10-mesh and 28-mesh existed than flotation. Reagent and power costs are high for the flotation process. When floating +28-mesh particles, cell capacity is lowered and some of the particles are lost with the refuse. The Tamaqua plant of the Lehigh Navigation Coal Co. floats —28-mesh coal and capacity of recoverable coal is 40 tph for 1800 cu ft of Denver cells; or 0.05 tons per cu ft of cell. At Kimberly 7.75 tph for 600 cu ft of cell gives 0.013 ton per cu ft of cell. At Bessie 14 tph for 800 cu ft of cell gives 0.017 tons per cu ft of cell. It would be appreciated if the author would comment on what he feels is the upper size limit of particle to attain most efficient utilization of the flotation process. The dewatering screw is a very interesting development since it offers a simple way to prepare coal sludge for more complete clewatering by drainage or mechanical dewatering on screen or filters. In other words it could be used to accomplish the same thing as a thickener tank. I would appreciate having the author's comment on how he thinks such a screw dewaterer would work on a froth.* The process as used in floating coal at the Bessie and Kimberly plants may be referred to as more of a bulk oil float in contrast to a froth flotation process. Experiments on increasing capacity of cells is most interesting since we are going through such an experi- mental period at the present time. Recently a double overflow was installed on our No. 30 Denver cells. So far results are not conclusive. In reviewing this paper the following comments are made pertaining to investigation of methods for increasing capacity: Supercharging: Supercharged air in matte flotation or for that matter the use of the normal amount of air drawn in by the impeller would in all probability cause such an aeration in the cell as to destroy the buoyant effect given to the coal particles by the excessive amount of kerosine used. In other words, air creates an agitation zone throughout the cell, creating a boiling and thereby giving a lower recovery in the cell. It would be interesting to know whether the 7 pct increase in recovery was with no air being admitted to the stand pipe. Changing Impeller Speed: The speed of a receded disc impeller for a No. 30 cell as recommended by the Denver Equipment Co. is, I believe, approximately 250 rpm. At this speed and using supercharged air in excess of 8-oz pressure, we have observed a boiling action in the cells. In our flotation we endeavor to obtain some degree of froth flotation using pine oil as a frother. The boiling action as caused by increasing the amount of air added to the cells is detrimental to recovery in froth flotation. It is our belief that to obtain increased recovery from a cell in froth flotation, additional air must be introduced but at the same time this air must be dispersed throughout the pulp in the form of small bubbles and this can only be done by increasing the speed of the impeller. Therefore, if Mr. Schiffman decreased the speed of the No. 30 impellers and at the same time continued to use supercharged air, the boiling action may have been increased because larger bubbles developed. The lower recovery as reported could be due to this factor. Decreasing the impeller speed will definitely decrease the power consumed but may have other disadvantages. First, we believe it will permit "sanding" in the cell and this in our opinion will increase the wear on the impeller and diffuser, especially so, if there is pyrite and/or sand present in the feed. "Sanding" in the cell when air is used, as in froth flotation, will effect the dispersion of this air and cause boiling.

Jan 1, 1951

By Kim Beattie

IN spite of the fact that in 1944 Canada experienced a decline in production of all her leading base metals-nickel, zinc, lead, and copper; despite uncured headaches in the coal-mining industry; and cheerfully ignoring a still further drop in gold, the most valuable product of her mines, which had the lowest output of any year since 1931, the Canadian miner retains the traditional optimism of miners everywhere as he looks forward to the postwar period. Some factors should keep the Canadian mining industry from being too optimistic of the coming era of peace, but the fraternity generally holds that its confident attitude towards the future is based on sound reasons. The decline in production in the Canadian mining industry last year can be almost wholly attributed to the serious shortage of labor and the difficulty in obtaining transport and supplies in remote areas. Some falling off occurred in the demand for certain strategic metals, but the diversion of gold miners, especially, without replacements being obtainable, to direct war work or allied pursuits, was certainly the principal cause of the reduced output in 1944. But that is a situation which will right itself at the close of the conflict.

Jan 1, 1945

By E. H. Griswold, C. E. Beecher

DURING 1931 the petroleum industry has faced the most hazardous periods of its existence, caused by large potentials, overproduction, and demoralized markets. Two state governors actually resorted to the use of the militia in an effort to restore a semi-stabilized condition within the industry, to prevent waste of the states' natural resources, and to restore prices to a level that would yield the states a reasonable tax revenue. These conditions have made it necessary to put into effect most. stringent economies and have produced a spirit of cooperation between companies to an extent that never before existed. The necessity for unified action on such matters as proration and the advantages to be gained by unit operation are being realized by the oil industry as a whole. Fewer wells have been drilled and wildcat operations almost eliminated: development and operation costs have been greatly reduced and more attention is being paid to efficient recovery methods. The net work of oil pipe- lines has grown rapidly especially in the area of East Texas. The construction and operation of natural gas and gasoline pipelines into areas far distant from the source of supply has been one of the outstanding accomplishments. Refining efficiency has continued to increase and the public is being supplied with a better grade of gasoline at a lower price. The unreasonable tax which state politicians have succeeded in placing on gasoline has encouraged tax evasion and unfair competition by un- scrupulous dealers and has misled the public as to the true price of gasoline.

Jan 1, 1932

A Discussion of the papers of James Gayley, on "The Application of Dry-Air Blast to the Manufacture of Iron" (see Trans., XXXV., 746, 1022, also pp. 315 and 745 of the present volume, and of J. E. Johnson, Jr., on "The Physical Action of the Blast-Furnace," p. 454. Chas. B. Dudley, Altoona, Pa.:—I am not a blast-furnace man, and this always puts me at a disadvantage because I cannot go into the details of the making of iron and steel. I have not the experience, and have to take the statements of other people, so what I say regarding the subject of this paper is not in the sense of an expert. When I first heard of Mr. Gayley's experiments, I said to myself, a I fear they will result in failure, since, apparently, Mr. Gayley has forgotten one chemical fact, namely, that carbon does not combine with oxygen in the absence of mater-vapor." This fact which was so astonishing when it was first brought out some years ago, and which those who are interested may find in the Journal of the Chemical Society of London, for 1885, page 349, and 1894, page 611, led me to think that the drying of the air would be a mistake. The general subject of the influence of water-vapor on chemical action is a large one; but the special point in which we are, for the moment, interested, namely, the influence of water-vapor on the combustion of carbon, was especially treated by Mr. H. B. Baker, in the papers referred to. Apparently, however, as the result of Mr. Gayley's experiments, we are to learn that the amount of moisture still left in the desiccated air is sufficient to secure perfectly satisfactory combustion. In thinking over Mr. Gayley's paper, it occurred to me that there were two alternatives, either of which might be chosen, namely, we might dry the air as Mr. Gayley does, or possibly we might, in a very much easier way, simply saturate the air at a constant temperature, and thus get uniform working and

Jan 1, 1906

By Oscar Weiss

An aerial magnetometer survey was carried out by the author's geophysical organization over the Vredefort dome, where Witwatersrand beds are wrapped around a granite plug 25 to 30 miles in diameter. The well- known magnetic shales of the Lower Witwatersrand system (to be referred to as LWW) give strong negative anomalies over the out-cropping portion of the dome. This is unusual as these same shales -cause positive anomalies over large areas near Johannesburg and along a strike of 130 miles between the East Rand and Klerksdorp. It is suggested that the negative polarization is caused by heat and stresses connected with the doming. This negative polarization of sedimentary beds, which usually cause positive anomalies, is a good example of how "magnetic lows" can be caused by "structural highs." Significant magnetic anomalies should be tested by gravity and seismic methods irrespective of the sign of the anomalies.

Jan 1, 1949

By Ballard H. Clemmons

THE future of the steelmaking industry of the Birmingham, Ala., district is closely related to and, in a large measure, dependent on the development of workable, economic processes of ore concentration. Operations thus far in the area have been possible only because of the fortuitous occurrence of iron ore, fluxing stone, and coking coal-all the primary iron-making materials- within a 25-mile radius of the blast furnaces. Commercial ore of the district consists mainly of a 10 to 20-ft hematite-calcite-silica bed locally known as the "Big Seam," a component of the Clinton formation of Silurian Age. At present mining rates, this ore will be available for a number of years. It is largely mined under 1000 to 2000 ft of cover and transported on 15 to 20" slopes that, in some instances, are as much as 10,000 ft long. Under these conditions, particularly with increasing distances from face to portal, mining costs are gradually becoming disproportionately high. Although not a major factor thus far, it should also be noted that the average annual ore output of the district is gradually be- coming more siliceous.

Jan 1, 1950

By Freeman Bishop

President Allende says he will expropriate all American investments in Chile and he's already well on the way to accomplishing this objective. What the average observer doesn't realize is that this has not only created big lossess for the copper companies. It could also take a chunk out of the U.S. taxpayers' pockets. Premier Castro expropriated the U.S. taxpayers' investment of over $100 million in the Nicaro (Cuba) nickel and cobalt operations-and U.S. Government protest over the loss was never heard above a whisper. Where the taxpayer comes in today is through the Overseas Private Investment Corporation, which was set up to guarantee U.S. companies' foreign investments against losses due to political changes. As of now, metals firms hold more than $300 million worth of obligations against this U.S. Government agency. The agency itself may not be able to raise more than $85 million, and a supplemental appropriation may be needed to meet its guarantees.

Jan 1, 1971

By D. S. Bloom

RECENTLY a report has been published on an investigation of the MO-RU system by E. Raub.' In this report it is stated that below approximately 1200°C the system consists of two terminal solid-solution phases and the intervening two-phase field; at 1200°C and above, an intermetallic compound labeled Mo,Ru, makes an appearance. Along with some other little known systems in which it was considered possible for a u phase to form, the Mo-Ru system had been under investigation in this laboratory. Since molybdenum and ruthenium have very high melting points and also since ruthenium is expensive, the investigation was confined to X-ray diffraction by sintered powder compacts. The compositions which were studied were (in atomic percentages): 75 Mo-25 Ru, 67 Mo-33 Ru, 50 Mo-50 Ru, and 25 Mo-75 Ru. All compacts were made from the pure powders, and no chemical analyses were attempted. Each compact weighed about 5 g. All annealing was done in evacuated Vycor capsules, and even though the capsules completely collapsed at 1250°C, they still admitted no air. The results of this investigation in general corroborate the work of Raub. Up to 1150°C the two terminal solutions and the intervening two-phase field were found, and at 1200°C and above an intermetallic compound was found. However, the composition limits of the compound were estimated to lie close to 70 atomic pct Mo rather than 62.5 atomic pct Mo as Raub had reported. At least the X-ray diffraction results indicated that the 75 atomic pct Mo specimen consisted of the molybdenum solid solution plus the compound, while the 67 atomic pct Mo specimen consisted of the ruthenium solid solution plus the compound and the equiatomic composition contained only very little of the compound. The most interesting observation, however, was that the diffraction pattern of the compound was similar to that of the well known u phases, except that unusually large lattice constants were indicated. The d-values, or interplanar spacings, of the diffraction lines (as produced by filtered copper KCX radiation) of the compound are given in Table I, as determined from specimens annealed at 1250°C for 9 hr and then quenched in water. Also shown are the lines of the Mn-Mo u phase as given by Decker, Waterstrat, and Kasper,' the lines of the Fe-Mo a as given by Goldschmidt," and the lines of the Mo-Ru phase multiplied by constants in order to make comparison with the Mn-Mo and Fe-Mo patterns easier. These results indicate that the compound in the Mo-Ru system is apparently isomorphous with the other o- compounds. The rather large lattice constants of the Mo-Ru a phase are acceptable in view of the comparatively large size of the constituent atoms. The data in Table I for the Mo-Ru compound check quite well with those given by Raub, not shown here, though there are some discrepancies between the two sets of data in the estimated intensities of a few lines. Although very little is known at present about this u phase, there are some things which may be pointed out, mainly in comparison with other better known u phases. Even though molybdenum and ruthenium are in the same columns in the Table of Elements as chromium and iron, respectively, the Mo-Ru u phase contains much more molybdenum than ruthenium, while the Cr-Fe u phase centers around or very nearly around the equiatomic composition; furthermore, the Mo-Ru u is stable only above approximately 1200°C, but the Cr-Fe u is stable only below about 825 °C. With respect to its being unstable below 1200°C, the Mo-Ru u is similar to the other binary molybdenum u phases in the Co-Mo and Fe-Mo systems. Similar to the latter two systems, the Mo-Ru u apparently exists over a rather narrow composition range, whereas the Cr-Fe u at lower temperatures is stable over a much wider composition range. The Mo-Ru u thus is closer to the other molybdenum u phases than to the Cr-Fe cr phase. The most striking feature of the Mo-Ru u phase, however, is the absence of any of the transition elements of the First Long Period.

Jan 1, 1956

By William B. Millar

IN ONTARIO development of the gold mines is being rapidly pushed, while the intensity of the search for new mines has probably not been equaled at any time in the past. Even to outline the results of recent prospecting activity in Ontario would be a big undertaking, but it would be timely and, I hope, interesting to Institute members to review some generalities regarding the work of the prospector and then to discuss in some detail the growth of Ontario's most promising prospect area, the Swayze district, where serious mining operations are already under way. Probably no one writing about prospectors and pros¬pecting can resist hoping that his article will not reach the eyes of a certain portion of the uninformed general public and cause a further influx of "prospective prospectors" into any given area. It is somewhat mystifying how so many people reach the conclusion that prospecting is in

Jan 1, 1933

By Joseph Hartshorne

EVER since the introduction of the Siemens regenerative furnace, it has been recognized that a certain amount of gas is lost each time the furnace-action is reversed. This loss comes, first, from the gas which passes through the free connection between the stack and the gas-main, which exists during the time the reversing-valve is turning over; and, secondly, from the gas which is in the chamber and flues, from the hearth to the reversing-valve, and which flows back into the stack when the valve is reversed. The amount lost each time is, of course, small; but, since a furnace is reversed from four to six times every hour for, say, 300 days in the year, the aggregate is large enough to be well worth attention. The estimate has been published' that, in Germany alone, the loss from the first of the above causes amounts to 500,000 marks per year. The loss from the second cause is, of course, much greater. A process for saving this entire loss, in use at Teplitz, Bohemia, for about three years, would seem to be of value even in this country, where coal is cheaper and where the small economies are not watched as closely as they are in Europe. This process, invented by Mr. Adelbert Kurzwernhart, late Technical Director of the Teplitzer Walzwerk, has been worked out with thoroughness. The loss from each cause can be calculated very closely for any particular furnace, and the results to be expected from the process ascertained. It can easily be decided, therefore, whether it is worthwhile to adopt it under any given conditions. The amount of chamber-gas lost depends upon,-(1), the cubic contents of the chamber, ports and flues upon one side of the furnace, up to the reversing-valve (deducting, of course,

Mar 1, 1906

By E. J. Eisenach, Edward Matsen

AT the present time the Climax Molybdenum Co. is the largest molybdenum producer in the world and the operator of the largest underground mine in North America. It has grown steadily and rapidly since its beginning in 1917. Only 250,000 lb of MoS2 were produced during the first year from 1917 to 1918 when the company was formed. Operations were suspended shortly thereafter because of the lack of a market and knowledge of the uses of molybdenum. During World War I it was used as a substitute for some rare metals and for minor chemical purposes. After 5 years of intensive research and sales promotion, Climax metallurgists succeeded in finding proper applications for the newly discovered metal and the mine was reopened in 1924. Demand for molybdenum increased gradually and in 1930, 3.5 million lb of MoS2 were produced. In the meantime, research work for additional uses of molybdenum continued until it had established itself as one of the most important alloying elements in producing high quality steels. After the start of World War 11, from January 1942 to October 1953, 43 million tons of molybdenum ore were mined and 484 million lb of MoS2 were produced. Climax mine is located in Colorado, 100 miles southwest of Denver and 12 miles northeast of Leadville on the Continental Divide of the Rocky Mountains. The principal mine workings range from 11,170 to 12,000 ft in elevation. Topographically, it lies in the base of a large cirque that is surrounded by Mt. Bartlett to the north, Clinton Peak and McNamee Peak to the east and Ceresco Ridge to the south. This cirque opens to the west and to the Ten Mile Valley.

Jan 3, 1954

By Frank L. Hess

BERYLLIUM is demanding more of the limelight, and the output of beryllium copper (containing 2% to~ 3 per cent of beryllium) seems to have grown 60 per cent above that of 1936, which was double that of 1935. There is increasing interest in beryllium-aluminum alloys and small quantities are being marketed at $50 per lb. for the contained beryllium. Other alloys also can be produced. Further price decreases for beryllium copper (now $23 per lb. for the contained beryllium) seem , possible and desirable. No difficulty has been experienced in obtaining beryl and a 'reserve stock has been built up. One supplier heretofore found reliable has offered to furnish 200 tons per month. Supplies during 1937 have come from the Black Hills in South Dakota, Colorado. India, and South America

Jan 1, 1938