Search Documents

By Ray E. Harris

Introduction A resource of more than 122 Gt (134 billion st) of minable trona and mixed trona and halite underlies an area of about 3400 km2 (1300 sq miles) west of Green River, WY (Culbertson, in preparation) (Fig. 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6 Mt (6.7 million st) (Kostick, 1983). About 90% of this came from Wyoming trona. This enormous deposit occurs in the Wilkins Peak Member of the Green River Formation that is of Eocene age. This formation is derived from sediments deposited in a large lake named Gosiute. Lake Gosiute occupied the Green River Basin in southwestern Wyoming some 38 to 54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition when the trona deposits were formed. A total of 42 trona beds are known. Of these, 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation). The production of sodium compounds from the trona deposits in the Wilkins Peak Member began in 1896 when wells were drilled within the present boundaries of the town of Green River. The purpose of the drilling was for extraction of sodium carbonate brines. Sodium carbonate (sal soda) was removed from these brines at a plant in Green River. Bedded trona was discovered in 1938 in a core from an oil well drilled south of Westvaco. In 1947, the underground mining of trona began. Production has continued from 1948 to date. Currently, five companies are mining trona and producing soda ash from the Wilkins Peak Member in Wyoming. Additionally, Allied Chemical Co. mines and processes trona for Church and Dwight's sodium bicarbonate (baking soda) operation in Green River. Competition in the soda ash industry depends primarily on the efficiency of mining and refining, allowing for lower-cost production. Newer plants and mine designs should increase efficiency. Solution mining holds promise as an even lower-cost method of mining. Employment in the soda ash industry is declining since the newer mining and refining methods are less labor intensive. Declines in employment, however, may be offset as production increases. Due to the large resource, the availability of minable trona should not be a problem for perhaps hundreds of years. Geology of Wyoming trona deposits Forty-two beds of trona or mixed trona and halite occur in the

Jan 10, 1985

By Jacob Masliyah, Zhiang Zhou, Tshitende Kasongo, Jianjun Liu, Zhenghe Xu, Jeawon Choung

"Slime coating is a recognized challenge in fine particle flotation, not only in decreasing recovery, but also in reducing the selectivity and hence froth quality. In this presentation, a novel method based on electrophoretic mobility distribution measurement to study slime coatings is described. By measuring electrophoretic mobility distribution of individual minerals and their mixtures, the interactions between these minerals can be evaluated.For illustrative purposes, a model system of fine coals, or oil sands with two different types of fine clays was studied. Flotation tests showed a significant decrease in coal (bitumen) flotation recovery with montmorillonite but not with kaolinite clay addition. When electrophoretic mobility distribution of a fine coal/montmorillonite clay mixture was measured, a single modal zeta potential distribution was obtained, in contrast to a bimodal distribution for fine coalkaolinite clay mixture. This finding suggests a stronger adhesion of montmorillonite than kaolinite clays on fine coal surfaces. In the case of bitumen, the bimodal zeta potential distribution was measured for the mixture of bitumen emulsion and kaolinite or montmorillonite, indicating a weak attraction of the clays by bitumen. In the presence of calcium, however, a single modal zeta potential distribution was obtained in the mixture of bitumen emulsion with montmorillonite but not kaolinite clays. These findings are in excellent agreement with bitumen flotation results, demonstrating that the electrophoretic distribution measurement is a powerful tool to study slime coating phenomenon in a complex fine particle flotation system."

Jan 1, 2002

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By R. L. Schmidt

One of a series published by the Bureau of Mines covering research investigations in rock drillability, this report of field drilling results extends earlier laboratory findings and provides a relatively simple procedure for predicting percussive drilling rates with reasonable accuracy. Two percussive drills mounted on a truck were used to drill a total of 25 rock types, and the results were used to develop a prediction equation. The equation was tested on a set of unrelated laboratory percussive drilling data, and the comparison between predicted and actual rates is shown in tabular form.

Jan 1, 1972

By Craig Compton

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers? compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

Jan 1, 2007

By Russell J. Foster

In this Bureau of Mines report a selection process has identified 14 nonstockpiled materials (cesium, gallium, hafnium, indium, osmium, rhenium, rhodium, rubidium, ruthenium, scandium, selenium, tellurium, thallium, and zirconium) that are linked to the continuing evolution of high-technology fields such as electronics, catalysis, and energy, and that have limiting factors associated with domestic availability. A qualitative assessment of the "potential criticality" of these materials was made through a consideration of end uses, demand trends and forecasts, production, mineral reserves, byproduct status, alternative supply sources, substitution and conservation options, and recyclability.

Jan 1, 1988

By R. H. Grau

Researchers from the National Institute for Occupational Safety and Health have demonstrated that mine-wide ventilation in large-opening stone mines can be improved by using low-pressure, high-volume propeller fans and constructing stoppings in key locations to direct and control airflow. In light of these findings, a comparative study was conducted to determine if a portable diesel-powered propeller fan could per-form more efficiently for dust dilution and transport than an axial vane fan for localized ventilation. The objective of this study is to evaluate both fan types for ventilation efficiency at an underground dump/crusher facility in a limestone mine. Results showed an improvement with the propeller fan to dilute both the respirable dust and the respirable silica dust around the dump/crusher facility. Overall, an average reduction of 20% in respirable dust and silica was observed at the dump/crusher location with the propeller fan.

By John W. Mentz

Phase I study efforts addressed: 1) acid mine drainage formation theory; 2) effects of inundation in reducing acid mine drainage formation; 3) summary information on the types of acid abatement technology currently available and the problems inherent in each; 4) analysis of two potential means of partially inundating abandoned segments of active underground mines to reduce acid formation. This subsequent Phase II Draft Final Report addresses all of the above, but concentrates on and defines Item 4. Seal construction techniques were taken through five logical steps as follows: A) Location Analysis; B) Coal Barrier Pillar Analysis: C) Ground Water Analysis; D) Design Considerations: E) Economic Analysis. The design details of both low wall dams and section seals were discussed in a series of segments: a) Case Histories; b) Feasibility Analysis; and c) Design (including representative calculations). Study efforts showed that both concepts are feasible only in certain mines where the geologic-hydrologic physical makeup is suitable to contain a mine pool. Low wall dams in particular were found to have extremely limited applicability as a means of pollution reduction. Section seals, while clearly dependent upon site specific conditions, have a some what broader range of utility and are more effective in pollution reduction. The proven dramatic reduction in acid mine drainage attributable to inundation makes this a concept that must be considered.

Jan 1, 1981

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

By Mario Paredes Malca

El presente trabajo describe el sistema experto por circuito de molienda desarrollado en la Concentradora Toquepala, donde se aplica la tecnología del control experto-basada en conjuntos difusos y modelos matemáticos. Las ventajas que presenta la aplicación de los sistemas expertos comprenden el aumento de la capacidad de tratamiento, la disminución del costo de operación y del porcentaje del producto que no cumple las especificaciones. Asímismo, el sistema experto se integra al sistema de control para asistir al operador en la detección de los casos, donde las operaciones se puedan descontrolar, aunque ésta no sea realmente su principal función. Si se le configura y sintoniza correctamente, el sistema experto detecta, diagnostica en forma continua los problemas de operación y aplica modelos matemáticos y estadísticos de optimización, interactúando con un sistema de control DCS o PLC.

Sep 12, 2005

The Macraes Mining Company Limited was listed on the New Zealand and Australian stock exchanges in January 1990, and the proceeds of the float were used to purchase a 70 per cent interest in the Macraes Gold Project, previously owned by BHP Gold Mines (NZ) Limited. Macraes Mining has had a 30 per cent interest in the project since May 1984, when it was incorporated. Project financing in the way of a gold loan was secured in February 1990 and construction commenced shortly afterwards. The mine construction activities were completed within nine months and the mine commenced operations in October 1990.

Jan 1, 1991

By D Craw

The Rise and Shine Shear Zone is a mineralised low angle deformation zone traceable for at least 7 km through biotite zone schist of the Dunstan Range, central Otago. Rocks from the shear zone obtained from recent drillholes are unweathered and facilitate paragenetic studies. There is a progression of mineral deposition from semiductile foliation-parallel shearing, to subsequent folding, and brittle fracturing. Sheared rocks are dominated by microshears containing fine grained hydrothermal muscovite and rutile that has recrystallised from metamorphic muscovite and titanite respectively. Euhedral pyrite occurs within segregations in the schist and is locally brecciated by the shears.   Arsenopyrite occurs within microshears and is intergrown with hyrothermal muscovite. Fractures within relatively undeformed schist are filled with ankerite, siderite, chalcopyrite, sphalerite and galena and these veinlets also crosscut the microshears. Locally the schist is folded and zones of brecciation, silicification and vein deposition overprint the rock. Vein quartz and albite predominate and arsenopyrite and gold infill breccia matrix and crosscutting veinlets. Sulphide deposition began in the later stages of metamorphism with pyrite deposited in quartz-albite segregations. Subsequent shearing caused brecciation of some grains and accompanied deposition of arsenopyrite ¦ gold and rare sulphides along foliation-parallel microshears. Minor amounts of chalcopyrite, sphalerite and galena were then remobilised in ankerite veins that crosscut the shears. In areas of high strain, arsenopyrite was then deposited as euhedral grains in veins and breccias. Synmineralisation deformation caused the brecciation of some grains and gold was deposited infilling fractures in the arsenopyrite. The paragenetic sequence shows gold mineralisation occurred in two distinct sets of structures (semiductile and brittle) that formed at different times in the formation of the shear zone.

Jan 1, 2006

By R Hoskings

Conceptual studies of the run of mine stockpiling and reclaiming requirements commenced in 1975. Final selection of equipment was made in 1978 and the equipment was commissioned in June, 1979. Equipment selection was made after extensive investigation and visits to existing facilities throughout the world. The equipment selected is described and compared with the alternatives. Foundations were designed to minimise cleanup effort and to ensure stability of equipment under design wind loading without storm bays. Programmable logic control enables the stacking and reclaiming facility to provide a blended feed to the coal preparation plant.

Jan 1, 1980

By Gordon E. Agar, Brian Lyons, Gregory H. Styles, William B. Kipkie

"Rock rejection during the flotation of a copper-nickel ore was improved by adding carboxymethyl cellulose to both a rougher and cleaner flotation stage. The selection of the rock depressant was based on laboratory rates studies. Plant operating results are presented which confirm the laboratory selection of two particular brands of carboxymethyl cellulose.The rock assay of the concentrate was reduced from more than 40% to less than 15%.IntroductionThe traditional method of selecting flotation reagents relied upon batch bench scale tests, conducted under arbitrary conditions, to identify the effect of the reagent under examination. Too often these were ""one-off"" tests with little or no regard paid to the reproducibility of the results. Sophisticated researchers used statistical methods to design and evaluate the experiments but they were still obliged to rely on the arbitrary and often unreliable batch tests to generate the numbers that were analyzed statistically. An interesting side-effect of the enhanced sophistication of the statistical analysis was often that no significant effects would be uncovered in a series of experiments that would have generated many positive conclusions and much further experimentation if the same results had been evaluated by the traditional method.In the recent past, at least two groups of researchers a have directed their attention to the reliability of the batch experiments with a view toward improving the reproducibility of the test data. In this work the best of the improvements advocated by both of these groups have been adopted in order to generate kinetic data from batch tests that are as reproducible as possible.The objective of the work was to reduce the rock content of a bulk sulphide concentrate produced at Inco's Shebandowan mill. During 1982 the Shebandowan concentrate analyzed 3.5% Cu, 7.4010 Ni, 25% pyrrhotite and more than 40% rock, which resulted in an MgO content of 10.4%. Besides the expense of shipping all of this rock to Sudbury, the rock also contributed to the poor filterability of the concentrate. On favourable occasions the moisture content of the filter cake was slightly over 20% by weight. The magnesia content of the concentrate was deleterious to the reverberatory furnaces used by Inco for smelting nickel concentrate because the slag viscosity increased as the magnesia content increased, and the nickel lost in the slag went up."

Jan 1, 1987

By Richard J. Mainiero, James H. Rowland

When most people think of explosives transport they think of a hazardous operation. We all know that we aren’t allowed to transport explosives through tunnels and are discouraged from traveling through heavily populated areas. Popular opinion suggests that explosives transport is a very risky operation. The authors decided to look into this a little more thoroughly and found just the opposite to be true. While there have been some disastrous world-wide accidents involving the transport of industrial explosives, this is not the case in the U.S. Over the past 10 years, accidents related to the transport of explosives used in mining and construction have resulted in 5 major injuries, 11 minor injuries, and no fatalities. Explosives and ammonium nitrate (AN) transport outside the U.S. has not had such a good record; there have been 4 major explosives or AN transport accidents resulting in a total of more than 300 deaths. Most of these fatalities could have been prevented if the accident site had been evacuated once the explosive or AN cargo began burning. The safe history of explosives and AN transport in the U.S. is due to diligent efforts by government, labor, and industry. However, accidents will become more common and disastrous if we become complacent.

By L. Adler

Longwall caving, one of the most economical and attractive mining methods, is yet one of the most difficult and hazardous.1 This dualism is inherent in a method which manipulates the mine supports themselves to aid in excavation. The difficulty is further compounded by the lack of an analytical method to predict and control results. This paper is intended to meet this need by providing a first approximation to the mechanics involved. The analysis will be limited to materials which are linear-elastic, homogeneous and isotropic. The rock structure is assumed to consist of beds of uniform thickness with no interbed bonding.2 Consequently, the mine roof can be likened to a beam, in which the action characteristic of longwall caving is the controlled deflection of the barrier supports. This deflection causes load to be intentionally transferred from these barrier props to the working face.3 Two of the requirements of this method, shared in common with other mining methods, are the provision of (1) adequate and (2) safe working space. The third requirement is the one characteristic of longwall caving and is somewhat in conflict with the second; (3) the development of near-failure static loads at the face. Requirement (1) is handled by spacing the barrier props sufficiently far from the working face for efficient operation. Requirement (2) limits the static stresses in the structure to predetermined allowable values. This means that it is not desirable to induce a maximum load on the working face as requirement (3) may imply. Such a condition could produce collapse in the whole structure. It is the purpose of the undercut to limit the depth, and thereby control the failure of the face. Therefore, requirement (3) really means the development of an optimum, not maximum, load which, in conjunction with undercutting, produces failure at the working face, with minimum powder consumption. Stress analysis requires an exact delineation of the structure and loads. The structure will be defined as the immediate roof and its supports. Since the roof is severed at the caving line, the supports reduce to the barrier props and the working face, as shown in Fig. 1. The mechanics of failure within the working face itself are complex and beyond the scope of this study, since the face represents a typical mine invert structure.4 However, this lack can be made good by the judicious collection of field data. The primary load on the structure is its own weight or body load which can be considered uniformly distributed over its upper surface. Additional loading occurs due to interference of overbeds with the structure. Wherever this occurs, the effect can be approximated by a load uniformly distributed on the upper surface of the structure.5 When this interference is intermittent, as with a much thicker overbed, the elastic curve for the overbed is superimposed on that for the structure and the extent of interference noted, as Fig. 2 shows. However, for simplicity, this study will ignore such intermittent loads without impairing the generality of approach. Consequently, the free-body diagram is that of a uniformly loaded cantilever beam with an inter-mediate support, as shown in Fig. 3. For convenience of analysis, the diagram will be divided just to the

Jan 1, 1961

By N. Niemuth

Strong demand for copper in developing nations such as China and India, plus the additional demand for industrial minerals to supply the Arizona construction market, brought about a record-setting year for the state?s mining industry. The value of Arizona?s copper production set a new high of $5.5 billion and pushed the total value of mineral production to $7.58 billion. This was also a record. As it has for many years, Arizona ranked first in nonfuel mineral production in the U.S. In addition to leading the nation in copper, Arizona ranked in the top five in molybdenum, sand and gravel, gemstones, perlite, silver, zeolites and pumice. Generally strong and rising prices, especially toward year?s end, fostered a bullish atmosphere that encouraged significant levels of acquisition and exploration. This activity has spread beyond the normal commodities to include some, such as manganese and fluorspar, that have not been mined in Arizona for decades.

Jan 1, 2008

Underground mine designs typically try to avoid extraction beneath streams and rivers of any significant size, especially when the overburden rock thickness between the stream bed and the mine is thin. Potential issues with mining beneath streams include excessive groundwater inflow to the mine; weak ground (roof, floor, and pillar) conditions; horizontal stress effects; as well as stream loss and other potential adverse environmental effects. However, there are times when crossing beneath a stream or river is necessary to move into a new area of mineral reserve without creating additional mine access points from the ground surface. Often, stream crossings are completed without thorough assessment, potentially resulting in increased costs, decreased safety, and, in some cases, failure to advance the mine. Selection of the most favorable location(s) to cross the stream must account for numerous factors and the associated assessment often requires a multidisciplinary approach. Stream crossing investigations often require geological, hydrogeological, geotechnical, and geophysical expertise. Phases of stream crossing investigations include desktop evaluation of maps and aerial photography, stream bed observations, drilling, detailed rock core logging, downhole geophysical surveying, hydraulic conductivity testing (packer testing), geotechnical laboratory testing, assessment, and reporting. The deliverables from a stream crossing assessment typically include geological, geotechnical, and hydrogeological characterization of potential stream crossing locations; classification of favorable and unfavorable crossing locations; recommendations for entry design and pillar sizing; and recommendations for if, and how, to conduct pre-grouting activities. Examples of technical aspects of data collection and assessment are provided based on decades of industry experience conducting stream crossing assessments in various underground mining scenarios.

Jul 28, 2020

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

In currently used mining methods, blasting techniques often causes dilution of valuable ore and results in costly processing requirements. In the context of narrow vein mining of thin and highly concentrated orebodies there is a need of a mining method that can reduce dilution in order to remain economically viable. This research project explored the viability of a new mining technology, thermal fragmentation, in narrow vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation, as well as for an existing method used for narrow vein mining; comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs, as well as increased productivity and ore recovery, meant that the new method would improve the financial performance of any operation. These results identify that there is an opportunity to introduce the thermal fragmentation technology to narrow vein mines within Australia, in order to lower costs and increase profit.

Dry weather since the third week in January has set back any prospects for an early increase in hydroelectric power in the Pacific Northwest, according to The Bonneville Power Administration. The 25% cutback made in July probably will not be restored in March or April. Noranda Aluminum, Inc., increased its price for 99.5% aluminum ingot from 66 cents to 70 cents per pound effective March 1, 1980. Revere Copper & Brass, Inc., also -increased its price for primary aluminum from 66.0 cents to 70.0 cents per pound effective February 1. Kaiser Aluminum & Chemical Corp. raised its international price for 99.5% primary aluminum from 72.6 cents to 82.6 cents per pound, c. i. f., effective February 26 on new orders and on shipments from March 15.

Jan 1, 1980