Search Documents

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By Lok M. Sharma

"Construction of a new bridge in a seismically sensitive area requires careful assessment of earthquake impact on the serviceability of the facility. Not only is the superstructure vulnerable, the foundations play a key role in the bridge’s survivability. A new bridge in eastern part of the state of Missouri in the U.S.A. is located in a seismically active area and hence subject to additional thrust on the foundations and superstructure and potential damage due to liquefaction. An eleven span bridge with foundation soils varying from shallow bedrock to over 30 m (100 feet) overburden soils were considered for the bridge support piers. Two of the bridge support bents located within the flood plain area through over 30m (100 feet) of alluvial deposits were considered most affected by an earthquake event due to the additional thrust and lateral ground spreading. This paper describes the determination of site specific seismic hazard, numerical modelling of the foundation system, and methodology of dynamic analyses, effects of lateral spreading and liquefaction potential on bridge support bents. From numerical modelling using FLAC, the increase in thrust on piers and deformations were computed to predict the behavior of the foundations.INTRODUCTIONA newly constructed bridge on route US 40 crosses the Missouri River west of St. Louis, Missouri and upstream of Mississippi River in mid-west USA. The west abutment area has near surface bedrock while the east abutment area has overburden deposits over 30m (100 feet) thick, mostly river sediments comprising of silts, lean clays and sands overlying bedrock. Softer layers of silts and sands in the east river bank area are assessed to be liquefiable during a high magnitude earthquake event. St Louis area has a potential for a high magnitude earthquake due to the New Madrid Fault some 160km (100 miles) south. The bridge foundations were designed as drilled piers, 2 m (8 feet) in diameter and socketed into the bedrock. Bents No. 10 and 11, located in the lower flood plain area of the river, are considered to be most affected by a seismic event.In order to perform dynamic analyses of the foundations, earthquake ground motion time history was developed for the specific site using a Probabilistic Seismic Hazard Analysis (PSHA) and selecting and scaling of a recorded time history. Relying on the U.S. Geological Survey (USGS) Earthquake Hazard Program for the PSHA and AASHTO Guide Specifications for LRFD Seismic Bridge Design, spectral acceleration values for the site were developed. The spectral acceleration values were for a 7 percent probability of exceedance in 75 years (1000 year return). Numerical modelling using FLAC computer program was performed. This paper presents the seismic design parameters, methodology used in the dynamic analyses, static and dynamic analyses, impact and mitigation of liquefaction on Bents 10 and 11 and the abutment fills, and effect of lateral spreading on the foundations in the lower flood plain area of the bridge. From the numerical modelling, increase in thrusts on pier foundations and estimated deformation were computed."

Jan 1, 2017

By Reza Y. Khaksar

Presented is a rigorous solution for the three-dimensional stability analysis of vertical shafts (excavations) subjected to the self-weight of the soil based on the upper-bound theorem of limit analysis approach. A rigid-block translational collapse mechanism is assumed, with energy dissipation taking place along planar velocity discontinuities. This mechanism is optimized to obtain the critical failure mechanism giving the lowest factor of safety for stability of shafts. Based on comparisons with other solutions, the method is generally found to be accurate in predicting the stability of vertical cuts.

Jan 1, 2006

By Annie G. Smelley

As part of its program to develop technology that will encourage maximum utilization of the Nation's mineral resources, the Bureau of Mines conducted research on debrining potash-clay waste slurries by means of flocculation with a high-molecular-weight polymer and subsequent solid-liquid separation on a rotating trommel screen. In laboratory batch tests, potash-clay waste slurries were consolidated from initial clay contents of 8 pct to final contents of 30 pct with a polymer dosage of 1.2 Ib/ton of dry clay waste. Small-scale continuous tests yielded debrined products containing 20 pct solids using a polymer dosage of 1 Ib/ton of dry clay solids.

Jan 1, 1983

By James M. Baugher, Donald W. Conrad, William J. Wiehagen

This report describes a process for quickly developing information that is useful for skills training. The process is called job training analysis (JTA). Its main use is to structure skills training at the jobsite. JTA supports structured skills training by identifying the job duties, tasks, and steps and the reasons why those job components are important. The outcome of the JTA process is a worksheet—a training outline based on the knowledge and expertise of experienced workers. Time invested in developing a JTA will result in significantly more time saved when it is used appropriately by skilled trainers. Like a roadmap, JTA saves time and energy. Experimental work at several mine sites helped document, refine, and validate the JTA process. JTAs for two mining jobs—roof bolting and lift truck operation—at two different mine sites are used to illustrate some of the concepts and the specific JTA process described in this report. The work at these two sites was influenced by cooperative work between the Mine Safety and Health Administration (MSHA) and the National Institute for Occupational Safety and Health (NIOSH) at several other mine sites and prior collaborative work with the U.S. Navy. The mining JTA process is grounded within the military research on the design of instructional systems. MSHA and NIOSH worked to simplify and apply the military training development model for mining industry use through collaborative work at several mine sites. The JTA process involves three activities: (1) planning, (2) a 1- to 3-day workshop where the JTA is developed using facilitated work with subject-matter experts, and (3) followup. Guidelines and considerations for each of these activities are included. Results indicate that the JTA process has been well received and valued by mining industry participants. It blends aspects of health and safety, production, maintenance, and crew coordination.

Jan 8, 2006

By B. Denby

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. The design and scheduling of open pit operations are consistent problems encountered by the surface mining industry. Numerous techniques and algorithms have been developed to assist the mining engineer in the creation of optimum development strategies. Virtually all the practical techniques that have been produced have concentrated on one of the aspects (limit definition or scheduling) at the expense of the other. It has long been recognised, however, that the two activities are intrinsically linked and thus solving either problem independently of the other can only ever produce sub-optimal results as a whole. This has been termed the "circular reasoning problem". It has also been recognised that, for all practical-sized situations, solving both problems simultaneously is virtually impossible using conventional techniques due to the massive size of the search space involved. A technique is presented which is based on a self-learning genetic algorithm, which provides a combined pit limit and extraction schedule simultaneously in order to maximise the NPV (net present value) of the extraction. The theory is developed in two-dimensions and a number of examples of its application are presented. It is proposed that this approach is a highly efficient, heuristic technique offering the potential to transcend the circular reasoning difficulties of separate pit limit and extraction scheduling systems. Extension of the technique into three-dimensions and its application to realistic problem sizes are discussed

Apr 1, 1994

It is difficult, and probably inadvisable, to frame rigid rules for the valuation of alluvial deposits, for such deposits are very diverse in type, varying, for example, according to the mineral sought and according'to the complexity of the deposit which, on one hand, may be a narrow welldefined alluvial strip at the bottom of which is a continuous mineral lead, or, on the other, may be a broad alluvial flat with discontinuous patches of the valuable mineral occurring at different levels throughout the alluvium.However, some definite procedure in valuation must be adopted when dealing with anyone deposit, and the fundamentals of such a procedure are applicable to almost all alluvial deposits.The methods described in this paper are based very largely on the valuation of a specific deposit and, although an attempt has been made to keep the discussion as general as possible, it contains some statements which, if traced to their origin, spring from the writer's association with that deposit. Such statements must be interpreted with sufficient flexibility to be appropriate to whatever area the reader may have in mind.The subject of valuing an alluvial deposit falls naturally into two divisions: The valuation of each borehole; the valuation of the deposit as a whole. The following discussion is therefore dealt with under these two headings.Some general matters are mentioned in a third section.

Jan 1, 1950

By L. K. Bandyopadhyay, P. K. Mishra, S. K. Chaulya, R. S. Singh, A. Kumar, N. Tripathi, K. Mandal

A comprehensive field study has been carried out to measure the background air quality status and identify the air pollution sources from opencast mines around a heritage site in India. Air quality modeling has been carried out to envisage dust concentration due to the existing and closed mines in the region. The predicted total PM10 and PM2.5 levels at the selected receptor locations ranged from 86.39 to 194.89 and from 34.82 to 99.55 µg/m³, respectively.

Jan 12, 2022

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines, describing mining methods and performance at individual mining operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and performance. Limestone deposits in Iowa are extensive and reserves are large. Most of the past production came from the eastern third of the state, although over half of the counties in the state have produced, or are now producing limestone. The stone is used as aggregate, road metal, agricultural lime, riprap, fluxing stone, railroad ballast, and in the manufacture of cement and lime.

Jan 1, 1962

By Thomas C. Anderson

Tiedback walls are now recognized and accepted as a good solution for a variety of structural problems: ? Retaining Walls and Bridge Abutments in cut situations ? Landslide stabilization ? Repair/support of existing walls Acceptable techniques have been developed for anchoring in cohesive and granular soils and in any kind of rock. Methods have been developed for adequately protecting tieback tendons against corrosion and for testing every tieback to verify its long-term load-carrying capacity. However, the major problem that the industry faces today is how do we get constructable and economical tiedback walls contracted for and built with minimal claims. This paper will explore the issue of "constructability" through a look at specific problems from actual projects. From a research report from the Construction Industry Institute, Austin, Texas (1986), constructability is defined "as the optimum use of construction knowledge and experience in planning, design, procurement and field/operations to achieve overall project objectives." Maximum benefits occur when people with construction knowledge and experience become involved at the very beginning of the project." The design and installation of tiebacks has been developed primarily by specialty contractors; each contractor has evolved its own methods of performing the work, and consequently, many of the techniques are patented and proprietary. The real question is, how do we make effective use of this knowledge and experience during the design phase of the project?

Jan 1, 1991

By Fritz Grübl

Modern shield TBMs allow tunnel drives through almost any type of ground. Thanks to high elaborated technical measures, significant subsidence of the ground surface can be almost entirely avoided. The tunnel lining behind the TBM must be capable of withstanding all loads without deforming, especially during ring erection and advance. Single-shell tunnel linings behind the TBM, usually reinforced concrete segmental rings, can be designed to fulfill this demand. With many projects, however, damage occurs to the lining. Repair costs may be extremely high. Reasons for damages and possibilities to avoid them are shown and explained.

Jan 1, 2001

By Christian Ottergren

"Modern crushers offer double the capacity and performance of classic models. In some cases crushers are replacing SAG circuits, the advantages being smaller investment and lower operating costs. Is Tertiary crushing replacing SAG milling as the most optimal grinding method? Does tertiary crushing achieve the same outcomes as SAG milling? This paper considers these questions and provides an assessment of the strengths of tertiary crushing in comparison to other methods. Two case studies: a Scandinavian Platinum Project, and CODELCO, are also presented.INTRODUCTIONResearch on basic parameters in crushing started at Chalmers University in 1993. The initial project has developed and now involves several related areas. Modelling in accordance with new theories has resulted in modified designs which have been implemented and shown improved performance at operating mines in Chile. Sandvik Rock Processing is a partner and a major supporter of this program. This paper will cover some of the achievements and give references to the research reports.The mining industry has for many years mainly used crushers of the traditional 7’crusher concept, with thread adjustment of the setting and with a spring or hydraulic overload system. This machine type has been the workhorse for crushing throughout the world. The explanation for the dominance of this machine is that it has a reliable mechanical design. It can be estimated that about 2000 crushers of this design are still at work.Technical development in all fields utilizes new technologies like high-strength materials, advanced control systems and more extensive use of hydraulics. This is the reason why today’s motorcars, for example, are more efficient, more reliable and more environmentally friendly than their predecessors in the 1950s. Crushers are no exception. This paper will cover experience from the latest-generation cone crushers developed by Sandvik Rock Processing.The parts in this paper related to the CODELCO ElTeniente copper mine in Chile are coauthored with responsible personnel from the operation at the mine."

Jan 1, 2004

By Forrest T. Moyer

INJURY experience and related employment information are presented in the chapter for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1964. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. All rates in the text are calculated separately on data before rounding, hence component rates may not add to the total rates shown in the tables. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III. COAL Injury experience of the coal mining industry was improved in 1964, as measured by the declines of 1 and 14 percent, respectively, in the frequency and severity rates. Although the total number of injuries increased in 1964, a slightly greater proportional increase in man-hours worked caused the frequency rate to drop to 44.65 per million man-hours. The injury-severity rate in 1964 was 7,832 days lost per million man-hours of exposure. Employment and injury data for 1964 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines. Fatality experience improved significantly with a record low number of 240 deaths in 1964. This total was 44 less than in 1963. The Nation's coal mines during 1964 were free of major disasters (a single accident resulting in the death of five men or more) for the first time since 1956. The

Jan 1, 1965

By S. R. Borrowman

This investigation by the Bureau of Mines was undertaken to develop information on the extractive metallurgy of thorite ores because potential ore bodies of this mineral have been found recently in Colorado, Idaho, and Montana. Basic information on thorite ore treatment that would be useful in appraising the potential of these and other domestic thorium resources was developed. The work was done mainly on thorite ore containing 3.87 percent ThO2 from the Powderhorn district, Colo., and on a composite sample containing 0.52 percent ThO2 from the Wet Mountains district, Colo. Limited tests of d corroborative nature subsequently were made on a sample containing 2.30 percent ThO2 from the Lemhi Pass area on the Idaho-Montana border.

Jan 1, 1962

By M A. Lund, C D. McCullough

In Australia and worldwide, open cut mining has become increasingly common over the last few decades through changes in excavation technology and ore economics. However, such operations frequently leave a legacy of open mine pits once mining ceases. Pit lakes will then form in mine pits that extend below the water table when dewatering operations cease. Pit lake waters are typically contaminated with metals, metalloids, saline or acidic/alkaline and rarely approach natural water body chemistry. Physically, pit lakes have unique bathymetries, are often strongly wind sheltered and have very small catchments. Nevertheless, pit lake waters often constitute a vast resource but of limited beneficial use (due to water quality issues); with a potential to contaminate regional surface and ground water resources. Water in pit lakes has the potential to be useful for a range of purposes in the Australian context of characteristic hot, dry climate and relatively few natural water bodies. Consequently, pit lakes can be seen to represent either a significant liability or a water resource to mining companies and regional communities. However, the lack of knowledge on pit lakes continues to hinder their proper management. This paper summarises the limited information currently available on water quality associated with Australian pit lakes. Information on pit lake occurrence, distribution and water quantity and quality is not nationally collated and requires immediate and ongoing attention from both mining companies and regulating authorities. Lack of a readily available database for pit lake occurrence, distribution and water quality fails to realise the potential for these water resources by both mining companies and Australian communities. Lack of access to pit lake quantity and water quality data may also lead to failure to manage this significant source of mining environmental risk.

Jan 1, 2009

Study on Separation Technology for Copper-Molybdenum Collective Concentrate

Sep 13, 2010

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

Ammonium nitrate-fuel oil (ANFO) explosives are unstable in hot, reactive sulphide-rich ground at Mount Isa. Under certain conditions associated with background heat, moisture, and chemical impurities from natural oxidation, ANFO composites in contact with hot ground disproportionate and the ammonium nitrate can undergo rapid exothermic reactions with sulphide.Reactions can occur in confined charges from prolonged contact with reactive sulphides, or by contamination with sulphide in loading. Partial interaction can result in misfires or premature detonation. Spilt, scattered and unpropagated explosive will undergo further reaction in sulphide-rich environments. ANFO-sulphide interaction is invariably exothermic and causes an irreversible chemical transformation of the ore.The heat generated during reaction may be dissipated, heating the environment, or rapidly accumulated to yield hot spots or areas in excess of 400°C. These can result in forced ignition of bulk sulphide and sustained combustion.Thermal analysis was used to define the critical conditions for ANFO-sulphide interaction and sulphide combustion.The occurrence of incandescent ore is attributed to the thermal interaction between exothermic hydrolysis oxidation, ANFO-sulphide, and combustion processes.Chemical agents and control methods have been developed to prevent ANFO-induced oxidation and combustion.

Jan 1, 1968

By N. B. Devi

The extraction of copper(II) from sulphate solution was investigated using LIX®984N in kerosene. The parameters that could affect the extraction, such as equilibrium pH, extractant concentration, salt concentration, various diluents, and temperature, were separately investigated. On the basis of slope analysis, the complex formed in the organic phase is proposed to be CuR2, where R is the anionic part of LIX®984N. The extraction equilibrium constant and Gibbs free energy ( G) of the extraction process were determined. The positive value of H obtained from temperature variation studies showed that the extraction process is endothermic. The extraction of copper was lowest when chloroform was used as the diluent. Separation and recovery of copper from a synthetic copper-nickel solution containing 6.35 g/L Cu(II) and 0.58 g/L Ni(II) was carried out using 20%(v/v) LIX® 984N. The separation factor ( = DCu/DNi) was found to be pH-dependent. A two-stage batch countercurrent extraction was carried out at an O:A ratio of 3:4 at equilibrium pH 1.05 for extraction of copper from copper-nickel solution, followed by copper stripping from the loaded organic phase with 15% H2SO4 at an O:A ratio of 3:1.

Jan 1, 2014

By Klaus Pöllath

The Netherlands RandstadRail project makes use of a large range of sophisticated geotechnical techniques to allow a shield driven tunnel to approach the central station of Rotterdam. This paper describes the construction of three deep excavation pits constructed with 1.2 m and 1.5 m thick diaphragm walls. Besides the presentation of the actual diaphragm wall activities special consideration is given to the break-in and break-out situations of the TBM into the deep excavations pits using sealing blocks and partly glass fibre reinforcement in the diaphragm walls.

Jan 1, 2006