Search Documents

By B. P. Watson

The first crush pillars on the Bushveld platinum mines were introduced at Union Section in 1978. Before the introduction of crush pillars, serious problems were experienced when stoping advanced to a point 30 m to 40 m on both sides of the centre gully. At least three to four stopes were collapsing per month. The introduction of the pillars stopped the stope collapses in the mining area where they were introduced. The residual stresses of these pillars were never measured; however, the successful elimination of the ?back-break? problem suggests that the original pillars had a residual strength of at least 8 MPa. Apart from back analyses, very little work has been done to determine the residual strength of crush pillars and only very recently have any measurements been made. The lack of knowledge in this field has resulted in pillars being designed based on experience. Concerns about stope collapses, similar to the Coalbrook disaster, have led to larger pillars being cut in more recent times. If such pillars were cut in brittle quartzites they would always fail violently but the ductile nature of the Merensky Reef generally allows large pillars to fail without bursting. Occasionally, however, one would burst in a working area. Increased incidence of bursting has been reported on some mines at deeper levels but most of these bursts occur in the back areas. Nevertheless, the incidence of bursting increases the risk of falls of ground in already dangerous areas, and the larger pillars decrease the extraction ratio. This paper describes the evaluation of stress measurements conducted in two boreholes over a crush pillar with dimensions 2.5 m x4.0 m, and a height of 1.2 m. Boussinesq equations for vertical and shear stress were used to analyse the original measurements and provide a stress profile across the pillar as well as the residual strength of the pillar. The results showed an unexpectedly high peak stress of 280 MPa at the centre of the pillar and a residual strength of 48 MPa. The reason for the high residual strength is suspected to be the result of the stiff environment under which the pillar failed and the small height of the siding on the up-dip edge of the pillar. More measurements should be conducted on several mines to establish a range of residual strengths for narrow crush pillars.

Jan 1, 2008

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By K. R. Gardner, P. B. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains ?1 ppm CN and 20 ppb Se; concentrations of other - major contaminants meet National Drinking Water Standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85% of the cyanide. Exploratory research shows that other bacteria removed up to 79% of the selenium from chemically oxidized, low- cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

By Gunderson C. T

The use of carbide tipped integral drill steels and detachable bits is discussed in relation to the means of drilling or cutting employed. It is stressed that only by correct use can the full value of these tools be realised.Factors affecting carbide quality, the design of shanking steels and the requirements and techniques of brazing in inserts are considered.It is essential that the brazed jointing between carbide and steel be strong but ductile. The methods used for the manufacture of carbide tipped tools are briefly outlined.INTRODUCTIONIn recent years the application of tungsten carbide to various mining tools in the mining industry, has developed to the stage where it is now regarded as an essential item in the production of coal and metal ores. In fact it is claimed that certain mining operations would not be possible if it were not for the benefits obtainable from the characteristic properties of tungsten carbide. The advantages of this hardmetal have, to some extent, influenced manufacturers to revise design specifiations of some machines, while againsome machines have actually been designed with tungsten carbide as their basic medium for operation.In general the applications fall into the following three categories:(a) Drilling hard rock by percussive means.(b) Drilling soft rock and coal by rotary means.(c) Coal cuttingThis paper is concerned with tungsten carbide tools associated with these three activities in Australia, the effectiveness of their application and significant points in their design and manufacture.

Jan 1, 1958

By J. C. Johnson

High-grade ore found in a shaft pillar at the Homestake Mine prompted a request for a Bureau of Mines study to determine if selected areas of the shaft pillar could be mined without jeopardizing the shaft. The design approach was to perform a finite-element study of the shaft pillar. Plan view and vertical sections were developed using two-dimensional, elastic, plane strain assumptions. Input into the model consisted of in situ stress measurements geologic mapping rock mass properties, and previous mining history. Results from the study indicated that ore-beating sections of the shaft pillar could be removed within the displacement tolerances acceptable for the shaft. Homestake engineers, using the results of the finite-element study and considering other factors, have designed and are beginning to mine the shaft pillar.

Jan 1, 1989

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

By Joel Darmstadter

The position of the coal industry in America’s fuel and power picture remains one of prime importance. Measured in Btu terms, the industry is the country’s leading energy producer and an important exporter. Foreign coal sales yield annual proceeds of about $4 billion. Coal’s one-fifth share of the nation’s energy consumption is nearly as high as that of natural gas. Coal is the electric utility sector’s principal fuel supplier. It accounts for about55% of the electricity generated at power stations.

Jan 1, 1999

By N. T. Lowe

The National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory (SRL), investigated a means to evaluate the potential impact of surface conditions above underground mines on emergency response activities. Recent events have highlighted the need to conduct critical emergency operations on the surface above underground work areas. Accessibility and usability of the surface, such as the ability to drill holes or deploy seismic monitoring or through the earth communications systems, are an important consideration for emergency response planning. This paper identifies critical surface conditions such as: surface waters, valley fill, highways, railroads and significant structures that must be considered in emergency response planning and in the conduct of emergency operations as they relate specifically to the seismic detection of trapped underground miners. Results of case studies indicate a need to consider the impact surface conditions may have on emergency response capabilities.

Jan 1, 2009

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003

By M. S. Miller

With prevailing assumptions that plentiful domestic coal reserves will be available for meeting our Nation’s expectations for on future low emission, coal-fired power plants, major government funding in Clean Coal Technology, and Carbon Sequestration Programs continues to be aggressive. However, after more than a decade of cutbacks in funding for domestic coal-related programs and personnel, there is a growing concern that adequate quantification and qualification of our Nation’s coal reserves is increasingly being compromised. This paper will define the growing concerns and dichotomies that continue to increase, and address the decreasing number of fossil fuel mapping and assessment programs by Federal and State programs.

Jan 1, 2004

By Steve Kral

President Bush’s National Energy Program and his Clear Skies Initiative both emphasize the use of coal to help meet the nation’s growing energy needs. And why not? Coal is currently responsible for more than 50 percent of the nation’s electricity generation. That fact, though, seems to be lost on policy makers, the environmental community and the public. Critics of coal advocate the increased use of renewable energy sources and the increased use of natural gas. Renewables, though, are only capable of generating a tiny fraction of the power required. Natural gas is expensive. And natural gas production cannot keep up with demand, especially given the nation’s increasing energy needs.

Jan 1, 2003

By Ashley P, Neale T

Alluvial gold was discovered on Sudest Island in 1888, and by 1893, an official production of 10 000 oz had been won by expatriate miners from shallow alluvial and colluvial workings. Hardrock sources were located and while one was developed at Mt Adelaide, production is unknown. Sudest Island comprises mostly phyllites and lesser coarse grained rocks which are cut by metamorphic quartz veins and basic (locally shoshonitic) intrusives. Sheared and altered basalts and serpent- inites represent are believed to be elements of an ophiolitic suite inferred to be associated with metamorphic core complex development and thus similar to tectonic environments on Misima and the D'Entrec- asteaux Islands. No epithermal-style quartz suggestive of a target similar to that on Misima Island has been identified on Sudest. A hardrock source for the alluvial and colluvial gold is interpreted to be metamorphic quartz veins similar to those in the Bendigo- Ballarat Zone of central Victoria, possibly remobilising gold derived from the meta- sedimentary and meta-igneous rock pile. The present focus is on development of a small scale alluvial gold mining operation in conjunction with exploration for hardrock targets. This latter programme remains at a reconnaissance stage.

Jan 1, 1991

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By M. K. Larson

The U.S. Bureau of Mines conducted a study to evaluate support interaction between conventional bolts and the rib at two Western coal mines. The principal goal was to develop guidelines for designing rib support under various conditions. At mine A, seven rib bolts were installed with load cells and monitored over a 4-month period. Fifty-seven pull tests were conducted with two types of anchors at various depths. At mine B, 163 pull tests were conducted. Results showed that during the 4 months of monitoring bolt load, tension in the bolts decreased over time in some situations and that anchorage capacity was reduced in a yielded zone. Load-versus-deformation plots from pull tests in the rib showed fundamental differences in anchorage behavior at the two mines, particularly when comparing results of tests in old pillars at mine A and tests in new ribs at mine B. Numerical modeling experiments indicate that coal bonding strength was the most significant factor in determining postyield anchorage capacity. Correlation of anchor yield point with anchor depth were more pronounced at mine A than at mine B; measuring torque may be a reasonable method of monitoring deteriorating anchorage capacity in a rib undergoing fracturing and yield.

Jan 1, 1996

By Madgwick J. C

A novel, microaerobic, heterotrophic microbial leaching system for manganese dioxide is described. Mixed natural microflora were enriched by addition of sugars and crude plant nutrItIOnal supplements. Between 84 and 104 mg MnH was solubilized per gram sugar at I per cent (w/v) concentrations for fructose and galactose in the presence of 0.03 per cent w/v dried microalgae (a Chlamydomonas species). Some 42 per cent soluble manganese was dissolved by microbial action on MnO, (3 per cent (w/v) pulp density) using a 10 per cent (w/v) molasses growth substrate.

Jan 1, 1983

By Michel Massé

Eleonore Project- Agenda ? Purpose and Technical Overview ? SmartEXEC Control Capabilities ? SmartEXEC System Archetecture ? SmartEXEC System Advantage Eleonore Project- Purpose and Technical Overview ? Control air quality while maintaining target production levels at minimum energy operating cost ? Improve safety, work place conditions and operation flexibility ? Reduce energy consumption and green house gases footprint

Aug 1, 2013

By K. Takahashi, I. Iwasaki

it is well known1 that racemic mixtures of optical isomers can be separated by passing their solutions through a column packed with r- or 1-quartz powder so that one of the isomers becomes adsorbed selectively on the asymmetric quartz surfaces. Although the natural occurrence of r- and 1-quartz is more or less equally distributed, some localities show enough deviations toward a higher proportion of l-quartz2 to suggest that optical isomerism might influence quartz flotation. Beta-amines have an asymmetric carbon atom, and therefore optical activity may be expected. Beta-amines are reported to behave quite differently from alpha-amines in the flotation upgrading of certain oxidized iron ores.3 It is of interest, for both practical and theoretical reasons, to determine whether or not optical isomerism plays a role in the amine flotation of quartz. In this article the results of Hallimond tube flotation tests and of adsorption measurements using d-beta-phenylisopropylamine on both r- and 1-quartz are compared. D-beta-phenylisopropylamine was chosen for the tests because it is commercially available in optical isomers. MATERIALS AND METHODS Brazilian quartz crystals were hand-sorted according to the difference in trigonal trapezohedral faces, and each crystal was further checked by the Airy's spiral.4 The respective crystals were then crushed, and the -150 + 200-mesh fractions were screened out for the Hallimond tube tests. The samples were cleaned by brief leaching with warm, dilute hydrochloric acid, and then by repeated rinsing with distilled water. In preparation for the adsorption measurements, they were then dry-ground in a pebble mill for several hours, washed a few times with distilled water, and finally dried in a vacuum desiccator. By means of the Krypton gas adsorption method, the specific surfaces of r- and 1-quartz samples were determined to be 27,700 and 19,800 sq cm per gm respectively, the difference being due mainly to the decantation procedure rather than to the inherent difference in their grindability. D-beta-phenylisopropylamine was the only collector used in the study. It was solubilized by neutralizing with 110% of the stoichiometric requirement of 0.1 N hydrochloric acid. The specific rotation of the d-beta-phenylisopropylamine was determined with a polari-meter using sodium D line to be, Although the d-beta-phenylis~prop~lamine showed absorption maxima in the wave length region of 250 to 270 millimicrons, due presumably to the phenyl group, these peaks were too sensitive to be used for colorimetric determination of the residual concentration in the adsorption measurements. The amine-picrate method, used in the colorimetric analysis of dodecylammonium chloride,' was found to work satisfactorily for the d-beta-phenylisopropylamine. The adsorption densities were thus determined after equilibrating 40 gm of the ground quartz sample with 300 ml of solution by tumbling in separate glass-stoppered Erlenmeyer flasks for one hour. EXPERIMENTAL RESULTS Fig. 1 presents the adsorption densities of d-beta-phenylisopropylamine on the r- and 1-quarts in the pH range of 6 to 7.5. In agreement with data reported in the literature, the adsorption density of d-beta-phenylisopropylamine was slightly higher on the r-quartz than on the 1-quartz, although the difference was not as pronounced as one might expect from the capacity of r-quartz and 1-quartz to separate racemic

Jan 1, 1969

By R. W. Barnes

This circular presents results of a survey conducted by the Bureau of Mines to ascertain the extent to which dust-control practices are employed in the coal-mining industry. This survey was initiated because of increasing realization of the possible harmful effects of the inhalation of dust upon the health of coal-mine workers and the advent, during recent years, of new types of mining machinery and new mining methods that may have a direct effect upon the extent of exposure to airborne dust experienced by persons mining coal. Anthracite Mines The survey covered 169 anthracite mines that were operating from November 1, 1953, to July 1, 1954. It showed that large mines employing more than 100 men were doing most to control dust produced during mining.

Jan 1, 1956