Search Documents

By R. Karl Zipf, Suresh Bhatt

Highwall mining is an important coal mining method. It appears that upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mines Safety and Health Administration (MSHA) data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwall miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Best practices to avoid trapped miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system. Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

By O. Ditsele

Coal plays an important role in the energy needs of the World. Given its wide abundance and low cost, coal use is bound to increase with the growing energy demand. Despite its importance, there are growing concerns over coal?s environmental burdens, especially its contribution to greenhouse gas emissions. To ensure sustainable extraction and use of coal, opportunities for minimizing potential impacts from coal have to be identified and exploited. Whilst extensive work has been done on life cycle assessment of coal use, especially in electricity generation which uses the bulk of coal produced, there has been limited work focusing specifically on coal mining. This study aims to estimate the cradle-to-gate life cycle climate change impacts of coal from a surface coal mine in the United States. The study employs general principles of ISO standards for LCA.

Jan 1, 2010

By J. F. McIlwain

The Bureau of Mines has investigated fumes generated by selected welding electrodes used in mines in order to help determine their relative health hazard potential. Fumes were generated and collected in an enclosed chamber for subsequent generation rate and chemical constituent determination. Shielded metal arc electrodes from the following groups were tested: AWS types E308-16 and E310-16 stainless steel, ECoCr-A Co-Cr hardfacing alloy, ENiCr Ni, an Mn-Cr buildup alloy, E7018 carbon steel, and EII018-M low-alloy steel. Flux-cored wire electrodes of this last group also were tested. Fume generation rates and the chemical composition of the fumes were measured. From these data, exposure in-dices were determined, which give a relative measure of the health hazard potential of using the electrodes. The effect of welding onto build-up alloy layers on the fume composition also was examined for five of the higher alloy groups.

Jan 1, 1987

By B. G. H. Thomas, W. P. Yant, A. C. Fieldner, R. R. Sayers, W. J. McConnell

"One of the outstanding problems confronting automotive engineers in attempting to construct motors of greater economy is that of eliminating the ""knock"" from the operation of the engine. Recent investigations of this detonation or knock in internal-combustion engines, especially of the high-compression type, have demonstrated that it can be eliminated or reduced by decreasing the reaction velocity of combustion by adding small quantities of certain compounds to the gasoline, This makes it possible to use engines of a higher compression ratio, thereby greatly increasing the mileage per gallon of gasoline consumed. The savings in fuel reserves from increasing the proportion of crude oil marketable as motor fuel and in permitting the designing of more efficient engines are obvious.Ethyl gasoline, one of the widely used anti-knock fuels, is ordinary motor gasoline to which has been added 3 c.c. of tetraethyl lead and 2 c.c. of a halogen carrier, as ethylene dibromide or trichiorethylene, or approximately 0.06 per cent of the lead compound and 0.04 per cent of ethylene dibromide by volume. Ethyl gasoline should not be confused with ethyl fluid, which is a mixture of concentrated tetraethyl lead and ethylene dibromide in the prowler proportions for mixing with gasoline, but is not a motor fuel and is not sold to the public. Also tetraethyl lead is not a motor fuel, and likewise is act sold to the public."

Dec 1, 1924

By S. Uludag

Spontaneous combustion of coal has been studied by laboratory techniques using an apparatus in a small-scale laboratory testing. Coal?s inherent characteristics can be measured using Differential Thermal Analysis (DTA) and Crossing Point Temperature (CPT) methods. The DTA curve obtained after testing is compared with actual inherent moisture and its effect on spontaneous combustion has been investigated. It has been found that the Wits-Ehac Index increases as the inherent moisture of the sample increases. Therefore it can be deduced that liability to spontaneous combustion increases with increased inherent moisture. In addition, volatiles have a catalytic affect on self heating immediately after the inherent moisture is reduced. This is identified as stage two in the thermogram. The inherent moisture has a cooling effect during the initial stages of testing and is visible in the DTA thermogram. In addition, while an increase in carbon content means an increase in Wits-Ehac Index value, an ash content decreases the likelihood of on spontaneous combustion. Keywords: Spontaneous Combustion, Differential Thermal Analysis, Crossing Point Temperature, Moisture, Coal, Laboratory Testing.

Jan 1, 2007

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two- thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two-thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By Eric E. Unger

Results are presented of a census of the machines used in surface coal mines in the United States. The numbers of each machine type and model reported to be in use are tabulated for large and small mines in the Eastern, Central, and Western regions. Also tabulated are the average daily usage times of the major machine categories and the numbers of machines that have acoustical and other cabs. Projections of the total numbers of primary production machines are given. It is found that heavy tracked dozers and wheeled front end loaders constitute the most prevalent machine types, and that generally a very few models of machines made by one or two manufacturers constitute a major fraction of the population in each machine category. About 70 percent of all machines are reported to have some kind of cab, and about half of these are reported to be acoustical gabs; it is noted that acoustical cabs generally came into significant use since about the early 1970's. It is observed that the percentage-wise mixes of equipment types used in the various categories of mines differ significantly for only a few types of machines, notably for heavy dozers and loaders, and for haulers, highway trucks, and internal-combustion engine-powered shovels and draglines.

Jan 1, 1977

By Jean-Sébastien Kroll-Rabotin, Éric Climent, Florent Bourgeois

"Falcon concentrators are enhanced gravity separators designed for concentrating fine and ultrafine slurries. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidisation water. In a former study, we investigated the physical mechanisms that govern the transport of ultrafine particles (in the range 10 to 80 µm) inside Falcon UF concentrators, and concluded that separation efficiency is governed by differential settling. Initially, we derived and published a predictive model of the partition function under dilute conditions. The present paper proposes an extension of the initial model to concentrated ultrafine suspensions for application to industrial scenarios. The paper discusses how hindered settling has been added into the initial model to account for solid concentration effects. The modified model is tested against experiments carried out with a laboratory scale UF Falcon concentrator from dilute conditions up to 30 vol%. A good agreement between measurements and model predictions is obtained, which confirms that our hypotheses about the physics of separation inside a UF Falcon separator remain valid even at high concentrations.INTRODUCTIONThe Falcon concentrator is a fast spinning bowl that is fed at its centre of rotation. It uses centrifugal force to separate particles that are transported inside a thin liquid film that flows upward along the inclined wall of the bowl (McAlister and Armstrong, 1998). Due to differential settling, dense and coarse particles are concentrated inside the bowl whereas light and fine particles are rejected with the overflow stream. The fast rotation speed of the bowl yields high centrifugal force several hundred times the attraction of Earth. Despite the thinness of the liquid film (between 100 µm and 1 mm with a Falcon L40) where separation takes place, the Falcon concentrator can treat high flowrates (up to 30 L/min). At the bottom of the bowl, an impeller transmits the bowl rotation to the feed, which drains upward by centrifugal force as soon as it hits the base of the spinning bowl (Figure 1)."

Jan 1, 2011

By J. P. Harrison, J. A. Hudson.

ABSTRACT: When considering the rock stress component of rock mechanics design, the basic procedure is to consider the pre-existing stress-state in the rock mass and then estimate the disturbance to this stress state as a result of engineering excavation. Failure criteria are applied to the final stress state to establish whether failure will occur. However, during the evolution of the stress state, the failure locus may be reached before the anticipated failure state and, in this case, failure will occur unexpectedly. This indicates that the complete stress path (defined as the variations in magnitudes and orientations of the stress tensor components resulting from engineering-induced or natural changes) must be considered. We list a set of stress path principles with their corollaries and then introduce a new and powerful method for simultaneously illustrating changes in the six independent components of the stress tensor. This method plots the magnitudes of the principal stresses above their orientational paths on the hemispherical projection, to provide a three-dimensional stress path locus for each of the three principal stress components. In connection with this presentational device, we illustrate a number of concepts associated with the stress path in rock engineering. For example, we show how the minor principal stress approaches zero at an unsupported excavation face, the interchange of the trajectories of two principal stresses when their magnitudes become equal, and the influence of the bounds on the principal stresses given by strength criteria. RESUME: Si on s’interesse à la composante “contrainte” lors d’un dimensionnement en mécanique des roches, la méthode de base consiste à considérer l’état de contrainte pré-existant dans le massif rocheux, puis d’estimer la perturbation à cet état générée par l’excavation projetée. Des critères de rupture sont appliqués à l’état de contrainte final pour établir si une rupture va se produire. Cependant, lors de l’évolution de l’état de contrainte, la surface critique peut être atteinte ce qui provoquera une rupture anticipée et, dans ce cas, cette dernière sera inattendue. Cela indique que le chemin de contrainte complet (défini par les variations de l’intensité et de l’orientation des composantes du tenseur des contraintes liées à des causes anthropiques ou naturelles) doit être pris en compte. Nous présentons un ensemble de règles pour les chemins de contraintes ainsi que leurs corollaires et, ensuite, nous introduisons une méthode, nouvelle et puissante, pour présenter simultannement les changements des six composantes du tenseur des contraintes. Cette méthode consiste à tracer l’intensité des contraintes principales sur le chemin d’orientation des contraintes à l’aide d’une projection hémisphérique afin d’obtenir le lieu, en trois dimensions, de chaque contrainte principale. En relation avec cet outil de représentation, nous illustrons certains concepts associés au chemin de contrainte en ingénierie au rocher. Par exemple, nous montrons comment la contrainte mineure tend vers zero à la surface d’une excavation sans soutenement, le changement de direction des deux contraintes principales quand leur intensité deviennent égales, et l’influence des conditions aux limites sur les contraintes fournies par un critère de rupture. ZUSAMMENFASSUNG: Bei ingenieurmassigen Taetigkeiten in Felsgesteinen ist es noetig die ungestoerten Gesteins Stress Componenten, die vor einem anthropogen Eingriff im Gestein vorhanden waren, zu kennen und erst dann Vorhersagen ueber Stoerung des Stress Zustandes, der durch einen ingenieurmaessigen Eingriff hervorgerufen wird, herzuleiten. Kriterien fuer das Versagen werden im letzten Stadium, des Stress Zustandes angewendet, um zu erfahren ob ein Versagen wohl eintreten wird. Es ist jedoch zu beachten, dass waehrend des Stress Aufbaus ein oertliches Versagen eintreten kann, welches vor dem eigentlichen, erwarteten Versagens Zustand auftritt. Diese Moeglichkeit weist darauf hin, dass der gesammte “Stress Path” (definiert durch die Variationen der Stress Tensor Komponenten in Richtung und Groesse, hervorgerufen durch ingenieurmaessig hervorgerufene oder natuerlich Vorgaenge) betrachtet werden muss. Wir fuehren eine Liste der “Stress Path” Prinzipien auf und stellen dann eine neue und wirksame Methode zur gleichzeitigen Darstellung der sechs unabhaegigen Komponenten des Stress Tensors vor. Diese Methode stellt die Groesse der “Principal Stresses” in Abhaengigkeit von ihrem rauemlichen Weg auf einer hemispherischen Projektion dar und erlaubt hiermit eine drei dimensionale Darstellung fuer jeden Ort des “Stress Path’s” in die drei Haupt Stress Komponenten. Im Zusammenhang mit der hier gegebenen Darstellungsart, verdeutlichen wir eine Reihe von Konzepten in der Felsmechanik. Wir zeigen zum Beispiel, wie der “Minor Principal Stress” Null zustrebt an einer Wand von einer nicht abgestuetzten Ausschachtung, den Austausch von Trajektorien zweier “Principal Stresses” wenn ihre Groessen sich gleichen, und den Einfluss der Groesse von “Principal Stresses” bei gegebenen Kriterien des Festgkeits Versagens.

Jan 1, 2003

Jan 1, 1994

By K Ehrig, J Griffith

An extensive suite of elements are routinely assayed on all resource drill core samples to assist in deposit scale resource definition, local mine scale delineation of ore zones, and ore characterisation for the planning and scheduling of mining and processing of ores at Olympic Dam. This paper discusses a deposit scale geochemical relation that can be used by mine geologists to find more high-grade ore at the local mine area scale at Olympic Dam.A 3D grade shell representing 0.8 per cent Cu was created for a mine area using drill hole assay data. This defined the geometry of the ore zone. The Cu-grade shell was then overlain onto the existing resource block model to evaluate the relationships between the Cu-grade shell, copper and other elements. The strongest correlation was between copper and manganese. The block model showed a dramatic decrease in the concentration of manganese just below the below the Cu-grade shell.Several drill holes that intersected the Cu-grade shell were selected to evaluate the copper manganese relation at the drill hole scale. As expected, the individual drill holes displayed a strong inverse relation between copper and manganese. A geochemical footwall was then modelled representing 0.1 wt per cent Mn. Using both the Cu– and Mn-grade shells, several drill holes were designed/drilled and all hit high-grade copper.For the vast majority of the deposit the inverse relation between copper and manganese is valid; however, in areas with intense chlorite alteration (related to amounts of mafic to ultramafic rocks) this relation is not as strong, due to increased manganese in the rock mass. Even though using the copper manganese relation as a drill targeting method was not always as reliable in a few small areas of the deposit, it demonstrates the value of using existing assay data integrated with the resource block model to discover local mine scale geochemical relationships which can be used to more effectively design drill holes to discover high-grade ore at Olympic Dam.CITATION:Griffith, J and Ehrig, K, 2017. Using existing data to improve the delineation of ore at the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit, in Proceedings Tenth International Mining Geology Conference 2017, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By B. D. Lichter

In a previous paper, Oelsen, Schuermann, and Hey-nertl pointed out the possibility of obtaining complete thermodynamic functions for alloy systems from calorimetric measurements alone. Specifically, if the heat content of a heterogeneous, multicomponent system is known as a function of temperature and composition, then it is possible to derive the heats, entropies, and free energies of formation of liquid phases and of solid intermediate phases of fixed composition. The authors present equations and graphical techniques applicable to eutectic systems and systems with intermediate phases without solid solubility at lower temperatures. eijering has considered possible extension of the treatment to systems with complete solid-state miscibility at lower temperatures; however, experimental difficulties practically restrict the method to systems with very limited miscibility in the solid state. The purpose of this note is to present an alternative derivation of the heats and entropies of formation of liquid phases and of solid intermediate phases from heat-content measurements alone. Fig. 1 shows three types of phase diagram to which the analysis may be applied. If the heat content is determined as a function of composition x, at temperature T, we have quite generally and the heat of mixing of the liquid is obtained directly from heat-content measurements. If the temperature T lies in a two-phase region (solid-liquid) then

Jan 1, 1967

By S. Kawatra, K. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from fines migration. Agglomeration of the ore can immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it “feels right”. We have developed procedures to quantitatively determine whether a binder gives good performance in an acidic solution, and have identified several binders that will be suitable for copper heap leaching.

Jan 1, 2007

By Lynch A. J

Comminution within rod mills has been investigated by use of a matrix analysis of breakage processes. A parameter, the number of breakage stages, has been introduced and comminution within all rod mills has been expressed in terms of the number of grinding stages and a function which describes the feed rate, mill diameter, and mill speed. The effect of variation in feed rate, feed sizing analysis and mill speed on the number of breakage stages is discussed, but no general relation is proposed because more study is needed.INTRODUCTIONRod mills are normally used as the first unit of multi-unit systems for the grinding of metalliferous ores and the cost of operating rod mills may be considerable. For both economic and metallurgical reasons, it is therefore necessary that the mills should be operated efficiently and that a knowledge of the mechanism of the size reduction process within rod mills should be as complete as possible. While a qualitative assessment of the process may be of some value, a quantitative assessment gained by describing the process in mathematical terms can be of much greater use because it may also be used for design and control purposes.In this paper, an empirical mathematical model is postulated to describe the size reduction process within rod mills and it is used to analyse the effects of variations in both rates and size distributions of the feed to the mills.GRINDING CHARACTERISTICS OF ROD MILLSMyers (1953) discussed the grinding characteristics of rod mills and suggested that a pronounced screening effect, resulting in the preferential grinding of the coarser particles, occurs within the mills. This is illustrated in...

Jan 1, 1964

By Hugo T. Dummett

I would like to share some observations about the mining business and place the ongoing discussion in the context of our changed world. The mining industry practices its trade in a universe defined by prices, laws and governments. Prices, as in what the industry is paid for what it produces, and the costs of goods and services. Laws that have to be transparent and fair. And governments that the industry prefers to be stable and supportive of the industry, and certainly not corrupt. However, the day-to-day realities of the mining business in 2000 are not what they were 10 years ago. Several events have occurred that have resulted in a less populated workplace that is obliged to work much smarter and faster. These include real declining prices for most mineral commodities; low and diminishing returns to company shareholders; massive restructuring of the industry through mergers, partnerships and alliances; gold’s changed role from reserve currency to just another commodity; the growing importance of native title and the startling imperatives of “sustainable development.” In addition, the “borderless world” now means that resource companies will need to pass the test of being responsible corporate guests who respect and enhance the social, moral and societal values of their host countries.

Jan 1, 2000

By Agne Rustan

This paper is intended to give a summary of the first ten Symposia on Rock Fragmentation by Blasting where the symposia activities were governed by a Steering Committee replaced at Fragblast 2 by an International Organizing Committee (IOC). At Fragblast 9 the name was changed to Fragblast International Organizing Committee (FIOC). Eighty four pages of statistical data about Fragblast 1-10 is documented on the Fragblast Website (ISEE.org).

Jan 1, 2014

By V. C. Kelessidis

The interaction between rock and drill bit during drilling has been modeled for many years, but a complete understanding of the phenomena occurring has yet to materialize. Successful models will allow the prediction of rate of penetration in a given environment and optimal selection of drill bit and drilling parameters, thus minimizing exploration costs. In most rock-drilling models the value of the unconfined compressive strength of the rock (UCS) is used in the predictive equations, within the concept of specific energy, and the value of UCS is the percentage of the value of the stress applied on the drilling bit in order for the bit to advance. While the exact percentage depends on the model used and it is not known with certainty, good knowledge of UCS is nevertheless required before any decent prediction can be made on rate of penetration. Determination of UCS, normally done via destructive testing, requires not only the availability of sound rock core samples but also expensive testing and significant time for the test, which frequently are not available for routine drillability predictions. Hence, a multitude of methods and techniques has been proposed for estimating UCS from various indirect and/or non-destructive measurements, or combination of measurements with neural networks, such as point load index, block punch index, unit weight, and apparent porosity, water absorption by weight, sonic velocity, and Schmidt hardness. The many proposed approaches are critically reviewed and the results are compared, and what becomes apparent is that after many years, not only in mining but also in oil-well drilling, accurate indirect determination of UCS is still an elusive goal. An equation to predict UCS from sonic velocity data is suggested based on several data sets reported in the literature. Use of the specific energy equation with UCS or sonic data and utilization of drilling data allows an estimation of the efficiency of energy transfer from the bit to the rock and of the friction coefficient. Analysis of data reported in the literature, both from laboratory and field studies, has shown that this approach is sound and enables the determination of energy transfer efficiencies and friction coefficients, which for the cases studied range between 15 and 30% and 0.15 and 0.30 respectively. Thus, the suggested data analysis approach allows drillers to focus on inefficiencies and optimize drilling practices in future campaigns. Keywords Rock drillability, unconfined compressive strength, prediction.

Jan 1, 2011

By Tano Balbin, Valery Astakhov, Juha Timperi, Lauri Koresaar

"Online elemental analysis is the basis of optimal flotation control in mineral concentrator plants. Traditionally XRF analyzers have been used as the online analysis method. However, online XRF analyzers struggle to measure elements below calcium in atomic number (Z=20). For many processes lighter element assays would be beneficial to improve control of grade and recovery. Processes where elements below Ca are required include P, Mg and Si in phosphate concentrators, Si, Mg and Al in iron concentrators, and S and C in gold concentrators. Laser-Induced Breakdown Spectroscopy (LIBS) based elemental analysis can readily be applied to these processes. LIBS is based on generating plasma in the slurry sample by a high energy laser and analysis of the plasma by optical emission spectroscopy. Capabilities of a new Courier® 8 analyzer based in LIBS technology are demonstrated for elemental analysis starting from lithium (Z=3). Results of a plant installation in a sulfide gold concentrator provide a good agreement with the analyzer and laboratory assays.IntroductionEffective process control can be regarded as one of the fastest paying investments for a mineral processing plant. Process optimization in flotation circuits requires constant feedback of the process state. If only manual laboratory samples are available, this optimization becomes difficult due to the long delay between taking the sample and acquiring the laboratory result. If the element grades are available in online basis, the operator or automatic process control system can make corrective actions in real time.Online X-Ray Fluorescence (XRF) analyzers have been in use at concentrators for decades. The XRF analyzers can provide a fast, accurate and precise analysis from slurry streams. However, the drawback of XRF analyzers is their lack of capability to measure elements below Ca (Z=20) in atomic number. The low energy X-rays of the low atomic number elements get absorbed by water in the sample, protective window of the analyzer, or air between the sample and spectrometer."

Jan 1, 2017

By J. -C. Trickett

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2 Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological models even further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip. Keywords: 3-D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; seismic micro technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2005