Search Documents

Up to the end of World War n, flat-back cut and fill stoping with or without square sets was the universal method of ore extraction. Rapid changes in practice occurred during the post-war years; first, ore extraction was fully mechanized; secondly, the stope design for new levels, notably No. 17 Level Zinc Corporation Ltd. and No. 19 Level New Broken Hill Consolidated Ltd., was modified to suit this mechanization; and thirdly, sub-level and shrinkage stopes were developed in orebodies where cut and fill methods would be uneconomical. The following is a brief survey of the changes that have occurred-most of which were inaugurated during the last five years.ROCK DRILLINGDuring 1951 open stoping was investigated in detail. In order to reduce steel handling problems, forged steel onepass detachable bits were introduced, but were soon superseded by the "Swedish method". Investigation showed that when using a bar and arm mounted 3-in. drifter the overall drilling time was approximately 6 min. per ft. compared with 4 min. per ft. using the light jackhammer-airleg combination with 1-in. hex. by 4-in. collared shank tungsten carbide-tipped steel.Although competitive with tipped steels on a cost per foot drilled basis (excluding miner's time), detachable steel bits proved most unsatisfactory for hard drilling conditions.Rapid blunting necessitated frequent bit changes and thus caused lost drilling time. This, together with rapid gauge...

Jan 1, 1957

By J Guo, K Williams, J Y. Guo, A W. Roberts, M Jones, B Chen

Numerical simulations using the discrete element method (DEM) were carried out to investigate the flow patterns and stress field redistribution at the hopper and feeder interface. The influences of different filling heights, belt speeds and clearances between the hopper bottom and feeder surface on feeder loads were studied. Meanwhile, experiments were conducted by utilising wedged plane-flow hoppers with different configurations and horizontal feeders with various clearances. The simulation results were compared with theoretical values and experimental measurements. In terms of the cases presented in this study, simulation results reveal good agreements with experimental observations regarding the flow pattern. Being similar to the theoretical values, the simulations provide close predictions on vertical feeder loads for steady flow states, but they may show significant overestimations for initial states. Additionally, suggestions are given for relevant simulation parameters based on the comparisons shown in this investigation.CITATION:Guo, J, Roberts, A W, Williams, K, Jones, M, Chen, B and Guo, Y J, 2017. Simulation investigation of flow patterns and feeder loads at hopper/feeder interface, in Proceedings Iron Ore 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Scott A. Walker, Roberto A. Lopez, Lori A. Simpson, David A. Shook

500 Folsom Street is part of the new Transbay neighborhood in San Francisco, which is being redeveloped after the 1989 Loma Prieta Earthquake damaged a freeway viaduct; removal of the viaduct created parcels of land available for development. The development consists of a 42-story residential tower with a six-level basement. The slender, core-only structure was designed using performance-based seismic design. Subsurface conditions include undocumented fill, Dune sand, marsh deposits, sand, and clay, all overlying sloping bedrock of the Franciscan Formation. The building is supported on a 10-foot-thick mat foundation approximately 62 to 72 feet below street grades; clay, sand, and bedrock are all present at mat subgrade. Under a portion of the mat, sand susceptible to liquefaction was present. The variable subgrade conditions and potential for ground failure, along with the depth of mat subgrade below street grade, created a challenge for the design and construction team to solve. The ground below mat subgrade needed to be improved to mitigate the liquefaction potential and provide more uniform support. The areal extent and depth of ground improvement necessary to support the mat with an acceptable amount of deformation was determined. Settlement was analyzed and subgrade moduli were provided for design of the mat, with multiple iterations performed to converge between the geotechnical and structural models. Based on the project schedule and logistics, it was beneficial to work from street grade to improve the ground. In order to target the depths below the mat and minimize wasted effort and materials within the depth of excavation, grids of jet grouting were determined to be the most economical ground improvement method; however, it was challenging to install the columns from 65 feet above the top of the target zone. During installation, QA/QC was performed to check that the jet-grouted columns were installed to the design depth and diameter and developed the design strength.

Jan 1, 2018

By P. Wells, P. Quinn

"A moveable flotation miniplant was designed and constructed at the research laboratory of Inco Technical Services Ltd. to address the need for flowsheet development with a limited amount of ore (such as drill cores). It consists of one rod mill, two regrind ball mills, one vibratory screen, 24 flotation cells of various sizes and two Venturi aerated flotation columns. The setup has continuous monitoring capability for pH, dissolved oxygen, oxidation-reduction potential, conductivity and temperature in conditioning tanks and flotation cells. Various options regarding flotation reagents, circuit configurations, and fineness of primary grind and regrind can be readily evaluated. The throughput of the miniplant is 20 – 30 kg/hour ore.Unit operations such as flash flotation, magnetic separation and gravity concentration can also be evaluated as an integral part of an entire flowsheet development.This communication describes the basic design features of the miniplant and some examples of applications are given.INTRODUCTIONInco operates numerous mines in Sudbury and Thompson and will shortly bring the Voisey’s Bay mine into production. It has long been recognized that the ores from different mines or from different depths of the same mine can give different responses in flotation. There is a growing need to properly evaluate the ores before feeding the mill to maximize the return of the mine/mill operation. Inco Technical Services Limited at Sheridan Park, Mississauga, Ontario has developed a batch laboratory procedure to address this issue. The results are considered in the overall economical assessment of new mine operations.For ores that cannot be processed by the existing mill operations or that will be processed by a new mill, it is necessary to develop a flowsheet that can maximize the economical return of the mine/mill operation. While recognizing the importance and contribution of the laboratory batch flotation procedure, it does not generate reliable data for flowsheet simulation and design. A full-scale pilot plant campaign is normally required to obtain the design data but often this is not possible due to a limited amount of ore obtainable from the drill core. A small-scale pilot plant (mini pilot plant or miniplant) capable of processing 20-30 kg/h ore can provide this data prior to a full-scale pilot plant campaign. A miniplant can also be used to optimize the circuit configurations, reagent additions and recycle options of process water before pilot plant work and can be used to test a different flowsheet configuration for an existing mill before re-piping a plant circuit."

Jan 1, 2003

By Robert Boehnke, Bernd Mueller

Despite enormous efforts over the last decades there are still many unanswered questions with respect to calculation and modeling of the blast process using appropriate physical laws. Most calculations of explosive charges of a blast design are based on experience, empirical observations or blasting theories with serious shortcomings. This paper presents a new theory for the design and calculation of a rock blast that is based on the momentum. It offers a clear-cut method for the calculation of blast processes. The theoretical results will be compared with on-site measurements by means of a newly developed strain sensor and further measuring equipment. The momentum theory helps better to explain physically the processes of a blast. On the basis of long-term statistical investigations a momentum balance can be carried out with the volume-based blasting momentum and the measurable momentum associated with the muckpile and the remaining rock mass. This type of consideration requires a complex procedure which includes the blastability of the rock masses. Realis tic strain measurements open a new interpretation possibility and judgment criteria for the most probable building damage, the dynamic impact on general types of buildings and also for the blast process itself. The blast-induced stress and the momentum generated could be back-calculated using a geophone profile and the strain sensor. The strain owing to a dynamic impact can be influenced by the changing of the drill-, blast- and shotfiring technique like the until now measured vibration velocity. In this way it is possible today to make a complex preparation, calculation and evaluation of blasts. The new techniques of measuring in connection with the momentum theory bring about an increase of the safety and a clearcut method of improving the blast processes. This procedure offers new possibilities for the precise calculation, simulation and modelling of blasts and resulting vibrations and leads to an increase of the safety as well as economic adaptation of the drill-, blast- and shotfiring techniques to a pre-determined blasting result.

Jan 1, 2003

By Elizabeth Varghese, Sanket Rawat, Prachuryya Kaushik, Ravi Kant Mittal

"Geo5 Software is gaining popularity worldwide due to its expediency in analysis and design of pile foundation. The analysis is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards. Moreover, the ultimate resistance of pile in the software is based CSN 73 1002, Fellenius method, NAVFAC DM 7.2 and Tomlinson method. Due to the specificity in calculation of ultimate resistance, it becomes necessary to validate the results arrived using the software for better accuracy. Furthermore, the above-mentioned methods are not necessarily popular in every design offices. Therefore, an attempt has been made to predict the efficiency of Geo5-v15 software to analyze the pile foundation by comparing it with the results obtained using the analysis based on Indian Standard IS 2911:2010, performed with spreadsheet specifically designed for the same purpose. The accompanying outcome of the comparison and several shortcomings found in the design part associated with the software has been highlighted in the later part of the paper. Besides, the optimization tool present in the software is also described for the more efficient and economic design of pile foundation, hence contributing as practical aid to structural engineers.INTRODUCTIONThe analysis of individual pile foundation and pile in groups can be said to include the three main important parameters – Ultimate bearing capacity, Settlement and Structural Design. The first two parameters are to be evaluated to check the reliability of foundation against ultimate limit state and serviceability limit state. The third parameter includes the analysis of pile against both horizontal and vertical load. This parameter mainly intends to evaluate the size of foundation and the amount of reinforcement. Geo5 is a software which can expediently compute the above mentioned three parameters just by the mere input of the necessary factors. The ultimate bearing capacity analysis in Geo5 is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards depending upon the drained and undrained condition of soil (Bowles, 1968; CSN 73 1002,1987; Felenius,1991; NAVFAC DM 7.2,1984; Tomlinson,1977). However, the method mentioned in IS 2911 (2010) is not the same and have slight variations in way of evaluating the parameters which affect ultimate bearing capacity. Therefore, it becomes necessary to evaluate the efficiency of Geo5 with respect to the value of ultimate bearing capacity and therefore, asserting the confidence in the software based method for the convenience of the designs in Indian Scenario. The present study aims to evaluate the efficiency of Geo5 v-15 software in predicting the ultimate bearing capacity of pile foundation. The results of the software are compared with the bearing capacity calculated using IS 2911 (2010) with the help of excel sheet. Moreover, as the software is frequently put under revision, therefore a comparison of this version has also been made with the latest version of Geo5 (2017) to check whether the latest revision has accounted for the discovered shortcomings. The design steps performed in the software is also shown. As Geo5 make use of IS 456 (2000) for the design purpose, hence it can be considered as reliable with respect to the estimate of the third parameter. Furthermore, the optimization process is also shown in the later part of the paper to emphasize the simplicity of the software in economizing the design cost."

Jan 1, 2017

By Christian J. Sorensen, Christopher Armstrong, Andrew Matejunas

A team consisting of junior and senior mechanical engineering students at New Mexico Tech worked on the design of an explosively loaded vessel, with a maximum load of 15 grams (0.53 oz) TNT equivalent explosive. The main challenge presented was to meet the stringent sample positioning specification of 3 microns in two Degrees Of Freedom (DOF) and one degree of rotation in a third DOF. This is to accommodate precise sample placement in a tight x-ray beam, and to bring areas such as explosives/metal interfaces into magnified field-of-view photography. This presentation describes the process and design decisions to arrive at the final product presented to LANL in December 2014. Our engineering analysis techniques will be reviewed, including use of American Society of Mechanical Engineers (ASME) Boiling & Pressure Vessel Code (BPVC) Code Case for Impulse Loaded Pressure Vessels (ASME BPVC Code Case 2564-3). Also discussed will be integration of Hydrocode computer models with Finite Element Method analysis.

Jan 1, 2015

By M. H. Kline

The Cranberry magnetite deposits occur in pre-Cambrian granite-gneiss, in a belt extending from 3 miles southeast of Cranberry, N. C., to about 6 miles southwest of Magnetic City, Tenn. The belt forms a curve) elongated to the north, approximately 26 miles in length. The Bureau of Mines investigation has been confined to the eastern part of the belt, comprising the area from Fork Mountain, Avery County, N.C., to the Hcupscup Knob prospects in Carter County, Tenn. The deposits were worked at least us early as 1820. The Cranberry Iron & Coal Co. and its successors operated the Cranberry mine intermittently for about 50 years until 1930, when operations were abandoned.

Jan 1, 1948

By C S. Szentesy, K Howie

The Rosia Montana gold deposit is located within the æGolden QuadrilateralÆ area in the Apuseni Mountains of Transylvania, Romania. The deposit is situated approximately 85 kilometres north of the regional centre of Deva, within the province of Alba, at elevations of up to 1100 metres above sea level. The Rosia Montana deposit contains a current resource of 344.07 million tonnes at an average grade of 1.3 grams per tonne (g/t) gold (Au) and 6.0 g/t silver (Ag) for a total (measured, indicated and inferred) contained resource of 14.29 million ounces of gold and 67.00 million ounces of silver. The resource was calculated using a 0.6g/t Au cut-off, a 10 x 10 x 10 metre block size and multiple indicator kriging. The low sulfidation style epithermal mineralisation at Rosia Montana is hosted within Tertiary age dacite intrusions and related vent breccias. Mineralisation is generally disseminated and associated with silica, adularia, illite, pyrite and carbonate alteration of host rocks, with minor late carbonate-base metal veins. Precipitation of precious metals is generally considered to have occurred as a result of over-pressurization, boiling and subsequent brecciation. The dacite intrusions are hosted in Cretaceous shallow marine and deltaic shales and slates, which overlie older Paleozoic sedimentary and metamorphic rocks within uplifted sections of oceanic sea floor.

Jan 1, 2002

By Emmanuel N. Zevgolis Ismene-Polyxeni Kostika

Keywords: reduction, kinetics, laterites, rotary kiln, dust In this work, the reduction kinetics of dust from nickeliferous Greek laterites is investigated. The dust is a by-product from laterite treatment in rotary kilns and it comes from washing towers, electrostatic filters and polycyclones. Laboratory made pellets from this dust were also examined. Reducibility was studied in the temperature range of 700°C to 850°C in a laboratory tube furnace. Kinetic analysis of the results showed that at lower temperature values the mixed kinetic model verifies the experimental results of dust and pellet samples. At higher temperatures (800° and 850°C) diffusion becomes the rate controlling mechanism. The calculated activation energy values verify also the above mentioned results.

Jan 1, 2005

Platiniferous horizons such as the Merensky Reef that are mined chiefly for their PGE contents constitute one end member of a continuum of Ni-Cu-PGE sulfide deposits; Ni-(Cu) sulfide deposits in which the PGE may or may not be by-products represent the other end of this continuum. Although it has long been thought that PGE-rich sulfides can only be developed by magma mixing in large magma chambers, new PGE data for the Bushveld Complex suggests an alternate model to account for origin of mineralization in the worldÆs most important Pt producer. Briefly, this model suggests that PGE-rich sulfides were initially deposited at depth below the Bushveld Complex as a result of interaction of a S-undersaturated mantle magma with S-rich crustal rocks. These PGE-rich sulfides were subsequently re-dissolved by a second magma, which introduced the PGE into the Bushveld Complex magma chamber, where the PGE-rich reefs were formed due to cooling of these magmas. If this model is correct, it means that large layered mafic/ultramafic intrusions are not a prerequisite for the formation of economic PGE-rich deposits. Exploration for Merensky Reef-type PGE deposits can be greatly facilitated by documenting variations in the background PGE contents of non-mineralized rocks collected on traverses across mafic/ultramafic intrusions; the mineralized horizons occur at cross-overs in ratios such as Pd/Cu, Pd/Se and Pd/S.

Jan 1, 2002

By David K. Hylbert

This study was designed to investigate roof falls in room-and-pillar drift coal mines and to determine geologic methods for predicting unstable roof conditions. The study area was located in Harlan County, Kentucky and the Bailey Creek (Harlan coal bed) and Highsplint (Darby coal bed) mines were selected for study. Correlations were made laterally between surface outcrops and within the mines using lithologic and trend analysis criteria. Lithologic criteria compared cyclic changes in roof strata. Results indicated that roof falls are associated with zones of weakness within or between five vertical cycles recognized. Abrupt lateral facies changes occur. In the Highsplint mine the roof was classified in four categories or conditions using 98 rib sections for control. Structure contour and isopach maps were used to project axial trends of the sandstone roof. A roof-fall zone was examined using ten NX cores taken from the roof and included lithologic, petrographic and clay mineral studies. At the Bailey Creek mine roof failure was caused by the heading direction being driven subparallel to paleochannel directions. Computer programs were used in trend analysis studies. Cross-bedding, paleo-channel trough axis and sole mark studies indicated a 350 discrepancy between surface and in-mine trough axes at Highsplint. A direct relationship between joint and "slip" frequency and direction with sandstone roll trends was found. Surface joints compared well with drainage Segments, hilt did not correlate with roof falls in areas of mines under overburden in excess of 600 feet.

Jan 1, 1977

By Sam Palombo, James José Varela

"Washing can be defined as the process used to eliminate or reduce the dirt (presence of fines or slimes) of one material. It is also the basic and oldest process applied to ore preparation for further concentration. This process, in combination with commnution and screening, form the so called washing plant and in many cases produce end products. This work describes the factors that influence the performance of the washing process and main washing technologies used in the mineral processing industry.The Hydro-Clean represents, since 1998, a state of the art technology in this area and is comprised of one of the most innovative solutions developed at HAVER & BOECKER. HAVER & BOECKER design and manufacture technology for mining and related industries. Today the Hydro-Clean is manufactured and sold throughout the Haver Screening Group (HSG) which is comprised of HAVER & BOECKER Maschinenfabrik Münster, HAVER & BOECKER Latinoamericana – Brazil and W.S. Tyler Canada.The Hydro-Clean is a washing technology based on utilization of high pressure water jets. To follow we will discuss how the Hydro-Clean’s different modes of operation result in several advantages related with mine waste reduction, recovery of saleable product, lower capital costs, superior washing results, less stress for the material, a wider range of application and less maintenance cost. Aside from these positive factors, its lower operation costs related to the consumption of energy and water are presented. It is important to note that the quantities, tonnages, data and management concepts presented in the paper are accurate for the time of writing and are subject to change and modification as operations progress."

Jan 1, 2009

By A. Lyndon

Vertical and lateral load tests were carried out on two 13 m deep bored cast-in-place instrumented piles, socketed into weathered sandstone. The first pile, 1200 mm in diameter, was loaded vertically to a maximum of 16000 kN and then loaded to failure under lateral load (1900 kN). The second pile, 1500 mm in diameter, was tested under lateral load up to a maximum of 2400 kN. It was found that the deflections of the 1200 mm pile were more than twice those of the 1500 mm pile under similar loads. The soils on the site are not easily tested in the laboratory, or by conventional insitu site investigation techniques, parameters needed in design can only be reliably obtained from pile test results. In this report shear moduli are back analysed from the vertical load test and the two lateral load tests. For these similarly installed piles very different design parameters were determined from the lateral load tests, the only known major difference between the piles being that the 1200 mm pile was loaded vertically before it was loaded laterally. Changes in G values needed to match performance under vertical load if applicable to lateral loading could have accounted for a significant amount of the difference.

Jan 1, 1989

By David K. Hylbert

This study investigated stratigraphic and structural causes of roof falls in room-and-pillar drift coal mines in nine mines in eastern Kentucky. A contract modification provided for remote sensing studies in the Dunkard Basin of West Virginia and Pennsylvania. Results of stratigraphic and structural studies of an earlier contract (H0133018) were applied to several new mines. It was found that similar rock sequences contributed to unstable roof conditions. Structure contour and isopach maps were found useful In projecting these trends together with fence diagrams. Using Landsat imagery, a direct relationship was found between lineament direction and the trends of rock jointing, roof fall zones, "snap top" zones and sandstone channels in the examples cited. It was found that, by analyzing lineament intersections, from 50 percent to 65 percent coincided with roof falls.

Jan 1, 1980

By R. Van A. Mills

Rapid deterioration and destruction of metal equipment in oil and gas fields cause waste of resources and financial losses that must be lessened or eliminated if operations in many important fields are to continue profitable. The magnitude of this destruction is proved by the huge consumption of iron and steel pipe, tubing, casing, pump valves, and sucker rods to replace worn-out equipment, and by the amount of such equipment that is left in wells or junked. (See PI. I, A and B, and PI. II, A and B, and Fig. 14, p. 61.) This destruction of equipment constitu~es in itself a serious waste, but contingent production troubles, such as underground leakage of oil through defective tubing and pumps, and the consequent loss of oil and gas because of damage to pay sands by infiltrating water and silt, frequent and costly repairs with necessary suspension of production, and the ultimate injury to or loss of valuable wells, often cancel all operating profits. Many of these troubles result from rapid destruction of metal equipment by corrosive waters. The strata penetrated by the wells usually contain saline waters. Certain types of these waters, with their associated gases, are intensely corrosive; they attack well casing or tubing so vigorously as to riddle it with holes, rendering it useless in a few years or even a few months or weeks after it is installed. Pump plungers, working barrels, balls and seats of valves, and screen pipe, as well as lead lines and other surface equipment, are ruined with equal rapidity. The development and application of practical methods to retard or prevent this corrosion are among the most urgent problems of the oil and gas industry. Although much progress has been made in preventing the corrosion of metals, the need for reducing the damage from corrosion in oil and gas fields is still imperative. This is especially true of underground corrosion in the wells, because underground conditions favor corrosion and are difficult to study; hence they have not been thoroughly understood. In efforts to stop ~amage to oil and gas field equipment by corrosion, numerous methods have been proposed or tried with varying success. Some of these methods are cheap and effective. However, it is surprising that in many important fields the damage by corrosion is accepted as necessary or unavoidable, although cheap and effective methods that have been developed and successfully tried elsewhere might greatly reduce the trouble or eliminate it. This bulletin describes common causes and effects of oil and gas field corrosion and outlines methods of abating the damage. In order to accomplish this purpose best, the writer has avoided taking sides in controversies between the advocates of different metals for oil-field use; instead he describes the methods of combating corrosion in the various fields and suggests experiments that may yield valuable results. Throughout the paper he has freely used information from published reports of other investigators.

Jan 1, 1925

THE most important part of the routine survey work on a mine is the keeping up-to-date of plans and sections showing progress of stoping and development work, and the direction of the latter for the purpose of making necessary connections. Except in specialcircumstances, e.g., major horizoittal development, the exactitude required in this work is not extreme, and a method of survey in keeping with the demands of the work itself is all tbat is required.For example, no one would consider measuring the walls of a stope to a fraction of an inch; such extreme accuracy would be wasted.The stope walls being irregular, a mean is usually taken, and for ordinary purposes a survey with a limiting error of six inches is quite satisfactory for the purpose of plotting either stoping or development.It is the author's aim in this paper to describe the method in use at the North Broken Hill Oompany's British mine. This method, while being sufficiently accurate for the purpose in view, possesses the very great advantages of speed and simplicity of operation,with a minimum of necessary equipment. This latter is a very important item where several surveys on different levels have to be carried out on the one day.Let it be understood, however, that the use of this method does not dispense with the theodolite, but simply serves as a convenient adjunct to obtain details and to extend the accurate theodolite survey up rises and down winzes, and through ladderways orwinzes into stopes, where the use of a theodolite, if not actually impossible, is often exceedingly inconvenient. This is particularly so on the British mine, where a large proportion of the ore is won from narrow and complex-dipping lodes, and where vertical ore...

Jan 1, 1928

[This is the sixth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative Agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of tines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935.-36.3/ The present report cover brands of gasoline represented by 1,490 samples plus thus: from the Pacific Coat, which ;sere averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. In some areas reports were received from 8 to 10 companies on the same brands of gasoline, Whereas in other areas only one Company reported on a brand. Thus, it can be seen that soma of the data are more representative than others. The inclusion of data from several cities within some of the districts has improved the report by reducing the number of brands reported by only one company. Severe changes have been made in the districts. A new district, Memphis, Tenn., has been formed to include Arkansas any western Tennessee. The Rocky Mountain area, have been divided into three sections. Salt Lake City and Denver form the Middle Rocky Mountain district; Laramie, Wyo., Idaho, Montana, and. Spokane, Wash., are included in the North Rocky Mountain district, and Arizona, New Mexico , and El Paso, Tex., have been combined to represent the South Rock Mountain district. The Cleveland district has been expanded to include Ohio ant. Indiana. Eastern Pennsylvania, Maryland, and northern Virginia are included in the Washington (D. C.) district. The Atlanta district includes Georgia, South Carolina; Mississippee, and northern Florida.]

Jan 1, 1938

By Sigmund D. Schwarz

INTRODUCTION In late 1970, an experimental geophysical program was undertaken at the Lake Huron Tunnel for the purpose of developing a geophysical technique that could be applied to determining the thickness of rock above the crown of the tunnel and identifying anomalous geologic conditions ahead of the face as the tunnel was advanced. The Lake Huron Tunnel is an 18.5 foot diameter machine bored tunnel having a total length of approximately 6 miles. The easternmost 4.5 mile section of the tunnel extends offshore beneath Lake Huron. At the time this study was started, approximately 1.5 miles of bore remained to be completed at the east end of the project. The tunnel is part of a raw water intake for the City of Detroit water supply. The Lake Huron Tunnel is bored in Antrim shale, a dense marine shale of Mississippian or Devonian age. The west end of the project encountered banded brown shale containing numerous calcareous concretions ranging in size from a few inches to more than 16 feet in diameter. As the tunnel was advanced in an easterly direction, a transition was encountered into very uniform gray shale. One set of prominent vertical joints was encountered with a strike running approximately 15 to 20 degrees askew of the tunnel axis. Bedding is essentially flat. Variable quantities of salt water and natural gas occur in the rock. The results of exploratory drilling carried out for preliminary design studies indicated that as little as 30 to 35 feet of rock cover could be expected under the lake at the east end of the project.

Jan 1, 1997

By Ihsan Berk Tulu

In the Analysis of Retreat Mining Pillar Stability (ARMPS) program, the magnitude of the abutment loading adjacent to a gob area is calculated using an ?abutment angle? concept. The extent of the abutment loading is determined solely as a function of depth from an empirically derived equation. In the recommended calibration method for LaModel, it was believed that the empirical equations for calculating the magnitude and extent of the abutment load, as used in ARMPS, were the best available methods for determining these critical overburden loading values. Therefore, similar calculations were implemented in the LaModel calibration method. However, the latest in situ stress measurements of abutment loading performed in the United States and Australia have shown that there can be significant deviations in the measured abutment magnitude and extent as compared to the predicted values from the empirical formulas used in ARMPS and LaModel. It seems reasonable that the overburden geology, depth, extraction panel width, and mining height should have a significant effect on the extent and magnitude of the abutment load. However, the current empirical formulas do not incorporate many of these significant parameters into determining the abutment load on the pillars. In this paper, stress measurements from US and Australian mines were back-analyzed by using analytical and numerical methods to investigate the measured abutment extent and loading. Ultimately, it was determined that the original empirical abutment extent formula in conjunction with the original ALPS square-decay stress distribution function was supported by the case histories in this paper. Also, for depths less than 900 ft, the average 21° abutment angle was supported by the case histories; however, at depths greater than 900 ft, the abutment angle was found to be significantly less than 21° and should be calculated with a new proposed equation.

Jan 1, 2012