Search Documents

By Bob Thomas

The roof drill operator productivity can be enhanced by the introduction of control technology The operators control station can be improved by considering human factors such as handle forces and control location. The smaller electrical controls can be located much easier than the traditional hands on valves. The operators control can he improved by using processors with programmable subroutines that assist the operator in the decision making process. For example to increase feed rate - to slow rotation - to avoid clogged steels - etc. The overall affect is to improve drilling and bolting consistency. The control system uses a dedicated processor packaged as an intrinsically safe control station. The roof drill operator is assisted in the drilling; arid bolting by a closed loop feedback system. The processor monitors the drilling parameters such as feed force, feed rate, rotation torque, RPM, drill position, and vacuum condition Based on the drilling parameters the processor executes pre-determined condition statements intended to enhance drilling The drill operator has an active display to alert him to the real time machine status. For example if the feed were to slow or delay due to a high vacuum level the display would show "high vacuum". The dedicated processor is available on the arm feed style machines, The prototype machines used programmable logic controllers to develop the feedback relations. The ability to record drilling parameters was extremely helpful in this development project. The extended use of the recording feature will aid operators in mapping the mine roofs Interpreting the recorded drilling parameters can reveal a void in the top or hard competent drilling The prototype machines also showed the importance of vacuum monitoring This feature is extremely valuable in softer materials, The benefits of the control system range from efficient use of the consumable bolting materials to uniform operator performance.

Jan 1, 1999

By Stanley J. Michalek

Good planning is critical to operating a safe and efficient mining operation. As the shallow coal scams become depleted, attention turns toward deeper mineable seams or remnant coal reserves. It is becoming more common to place a mine in a scam that is below or adjacent to existing mine workings. Significant research has been conducted regarding the ground control issues of multiple scam mining. However, safety aspects of the operation may not be fully considered. Safety issues include working below or adjacent to a flooded mine and controlling gas Communication between the active mine and the nearby mine. This paper will discuss the safety issues a mine operator should consider when working under or adjacent to mines that may be flooded with water.

Jan 1, 2000

By Edward S. Custer

Recent investigations of mine roof falls have demonstrated that roof failures are generally associated with geologic conditions. The roof falls can be predicted by using the techniques of depositional modeling for the coal bed and roof rocks, and by lineament analysis. The ability to predict potential roof failure areas will allow the engineer and mine planner to develop a mine plan to avoid the roof failure areas and thus reduce overall mining costs. The ability to avoid roof failure areas also will permit maximum recovery of the coal resources.

Jan 1, 1981

By Khaled Morsy

Most of the available numerical codes simulating the reinforcing effect of fully grouted bolt are accomplished by a series of bar elements which are connected along their length to the host rock by shear springs and sliders. The spring-slider system represents the shear bonding effect between the bolt and the host rock. This paper describes a three dimensional finite element modeling technique for the 3D simulation of fully grouted bolt reinforcement. The proposed technique introduced a physical simulation for the fully grouted bolts. The bolt simulation is composed of a series of beam elements (representing the steel rebar) embedded in brick elements (representing the grout). Because of the complexity of the grout/rock interface, ABAQUS explicit code was used. A modification of the ABAQUS default friction model was conducted to consider the cohesion of the grout/rock interface. The interaction between the grout and the host rock is simulated by the modified friction model. To verify the proposed technique, a simulation of the pull out test we conducted. The results from the simulation were compared with former studies

Jan 1, 2004

By Hamid R. Nikraz

This paper reports the finding of a comprehensive investigation carried out to evaluate the compaction characteristics of saturated sandstone aquifers in the Collie Coal Basin under conditions anticipated during dewatering operations. A triaxial technique has been adapted to evaluate the compaction characteristics of the sandstone aquifer in the Collie Basin. This technique, which allows the strata stress regime to be reproduced by triaxial loading with zero lateral strain, also provides a precise evaluation of lateral stresses and consequently Poisson's ratio under in situ conditions. The paper contains a description of the equipment commissioned, test techniques, results, analysis and interpretation of the data obtained. The testing evaluation techniques are general in nature and can be applied to field situations in locations where similar weak sandstones occur.

Jan 1, 1993

By Keith Heasley

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 in (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.'s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysts of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. `The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

Jan 1, 2001

By D. N. Cleaver

Like other influence function methods, the SWIFT subsidence prediction program, developed within the Mineral Resources Engineering Department at the University of Nottingham, requires calibration to regional data in order to produce accurate predictions of ground movements. Previously, this software had been solely calibrated to give results consistent with the Subsidence Engineer's Handbook (NCB, 1975). This approach was satisfactory for the majority of cases based in the United Kingdom, upon which the calibration was based. However, in certain circumstances within the UK and, almost always, in overseas case studies, the predictions did not correspond to observed patterns of ground movement. Therefore, in order that SWIFT, and other subsidence prediction packages, can be considered more universal, an improved and adaptable method of regional calibration must be incorporated. This paper describes the analysis of a large database of case histories from the UK industry and international publications. Observed maximum subsidence, mining geometry and Geological Index for several hundred cases have been statistically analysed in terms of developing prediction models. The models developed can more accurately predict maximum subsidence than previously used systems but also, are capable of indicating the likely range of prediction error to a certain degree of probability. Finally, the paper illustrates how this statistical approach can be incorporated as a calibration system for the influence function program, SWIFT.

Jan 1, 1995

By Cao Shenggen

Experiences in the developed countries have shown that continuous increase of panel width (or face length) is one of the major technical trends for high production high efficiency mines. Increasing the panel width will increase not only the panel output, simplify the gateroad layout, facilitate high concentration of production, but also increase resources recovery and facilitate protection of surface structures. This paper uses the No.4326 super- wide panel, Wangzhuang Coal Mine as an example. This mine employs the fully-mechanized top-coal caving longwall mining method. Through surface subsidence monitoring, the dynamic characteristics of surface movement were obtained. The dynamic surface movement during mining and the final surface movement after mining were predicted using the Mining Subsidence Prediction System. The results indicate that after mining, the surface above the super-wide panel reached a state of full subsidence, So it can ensure the No.309 National Highway above is located in the flat bottom of the subsidence basin, and there is little impact on the national highways when panels on both sides of 4326 Panel are mined.

Jan 1, 2003

By Michael Gauna

Ground fall injuries and fatalities in United States underground coal mines have shown a diminishing trend. Advances in bolting and standing support systems have led to improved safety in underground coal mines. However, the Crandall Canyon Mine disaster in 2007, in which 9 individuals were fatally injured as a result of a widespread collapse, emphasized that proper mine design is a critical issue that must be addressed. The Mine Safety and Health Administration (MSHA) has instituted technical review procedures structured to facilitate the implementation of safe mine designs in underground coal mines. The technical review process and the typical information required are outlined in this paper. The range of mining situations that lead to a technical review, common design methods submitted for review, and their relevant guidelines and limitations are also discussed. Additionally, the relationship between design criteria and mine site historical experience is discussed.

Jan 1, 2011

By Ross Seedsman

There are many models for how roof bolts behave, one of which is prevention of shear along bedding. The basis of this model is that a roof beam will not delaminate if bedding parallel shear can be prevented. A key point in such a model is that bedding discontinuities are present naturally in the roof and that mining induced stresses do not generate new surfaces. The presence of these discontinuities means that the rock mass must be modelled as a transversely isotropic material if continuum codes are used. A limit-equilibrium type design method for specifying roof bolts is being developed using voussoir beam and excess shear force concepts. The method incorporates much of what operators know intrinsically about roof reinforcement, and allows mining engineers to focus on the key uncertainty - the frequency and location of bedding surfaces in the immediate roof. Areas where more research is required are highlighted.

Jan 1, 2000

By Daniel W. H. Su

A floor-bearing capacity test apparatus was designed and constructed to determine the true bearing capacity of soft floor materials beneath coal pillars or longwall face supports. The apparatus has been employed in entries up to eleven feet in height. Results of in-mine floor-bearing capacity tests suggested that the ratio of the soft fireclay thickness to the bearing plate width and the moisture content in the fireclay were the most critical parameters affecting the ultimate bearing capacity. Foundation engineering principles were applied to interpret the field test results to estimate the floor-bearing capacity beneath longwall face supports.

Jan 1, 1993

By P. M. Lin

The problem of abandoned mine land (AML) subsidence is getting more severe because abandoned mine lands which used to be located in the remote areas have been gradually developed into suburbs or even urban areas. Abandoned mine subsidence is also becoming more common than before because the time-dependent effect of exposed underground materials. These materials will deteriorate gradually and cause subsidence as time passes. Subsurface conditions of abandoned mines are seldom known to the public. Mine maps are not always available. If the mine mans are available, their accuracy are very - often questionable. In addition, the most common damages to surface structure and ground surface due to mine subsidence can also be created by other non-mining related geological hazards. These factors make the study of abandoned mine subsidence significantly complicated, tedious, and inconclusive. For instance, the cause, time, and amount of surface subsidence can be predicted with relative accuracy during active mining. However, it will be a considerable challenge to do so on abandoned mine subsidence. If abandoned mine subsidence can be predicted in advance, then the damages can be held to a minimum. However, this prediction technique is not yet well developed. Therefore, remedial measures require more attention. In order to have effective remedial measures, the real cause of the damage should be determined first. This paper describes the approach which was employed for the determination of abandoned mine subsidence. A site investigation was made first. According to the information obtained from the site investigation, a hypothesis was set up. Then the instrumentation was used to prove the hypothesis. By going through the procedures for several cases, a guideline which can be used by the inspectors to inspect abandoned mine subsidence will be established.

Jan 1, 1987

By Christopher Mark

Despite more than half a century of experience with roof bolting, no design method has received wide acceptance. To begin to improve this situation, National Institute for Occupational Safety and Health (NIOSH) conducted a statistical study of roof bolt performance at a number of mines throughout the U.S. Case histories were collected from 37 mines with a variety of roof bolt types and patterns in a wide range of geologic environments. Performance was measured in terms of the number of roof falls that occurred per 10,000 ft of drivage. The study found that roof falls are rare when the roof is strong and the stress is low, even with light roof bolting patterns. The focus of this paper is on the more difficult conditions, where the roof is weaker and/or the stress is higher. Analysis of the results led to guidelines that can be used to make preliminary estimates of the required bolt length, capacity, and pattern. The guidelines are based on the depth of cover (which correlates with stress) and the roof quality (measured by the Coal Mine Roof Rating (CMRR), and the intersection span. Another contribution is a formula for estimating the horizontal stress level in the eastern U.S. coalfields as a function of the depth of cover. The design guidelines are currently being implemented into a computer program called Analysis of Roof Bolt Systems (ARBS).

Jan 1, 2001

By Thomas L. Hutchinson

The mechanical design of a roof support is basically a matter of a statics and dynamics problem, assuming of course, that the imposed loads and mining conditions are known. Here in the Appalachian coal fields the general conditions are known well enough to allow the majority of the proposed new faces of longwall to be furnished with standard commercially available supports equipped with suitable variants and options. While not trying to negate the primary importance of thoroughly investigating a potential face and the selection of the correct equipment for that face, it still becomes clear that an equally important aspect of the design of an adequate ground control program has in the past too of ten been overlooked, having been overshadowed by the ?endless? selection process of the roof supports proper. The equally important aspect which this paper discusses is the overall design of a mining system, which design incorporates not only the size and capacity of the equipment but the following points as well, namely: Equipment adaptability to mining scheme, Equipment va. human constraints, Operation at the designed levels, and Coordination of operation, maintenance and support design. Unless the coordination of these factors is considered in the design and selection of the equipment, a lopsided and inefficient operation is possible. How can we afford to put an 8-10 million dollar investment up to chance as to whether it will yield optimum results or not?

Jan 1, 1981

By Alan A. Campoli

Fosroc continues as a leader in the development of cementitious technology for the mining industry. The considerable expertise accumulated in the development of the Fm cement line has been employed in the development of two pumpable, supplemental roof support systems. The Tekprop system is a unique combination of steel and concrete, specifically designed as a viable alternative to conventional wooden supplementd support. The second system is the Fosroc mineable mi which is a cost competitive variable yield system designed to support longwall ventilation and predriven recovery room entries. Two, separate, ongoing, full scale applications of these systems will be discussed during the inference presentation

Jan 1, 1997

By Fred Leighton

Outbursts, or the sudden and sometimes catastrophic expulsion of coal and gas into the working area of a coal mine, are a little understood and growing problem. The AE/MS (Acoustic Emission/Microseismic), or rock talk, activity prior to and associated with several outbursts has been recorded using ultrasonic and micro- seismic equipment and has been analyzed by the Bureau of Mines. Analysis of these data indicates that outbursts are comprised of several failures in rapid succession and that anomalous AE/MS data suitable for providing failure warning are generated 15 to 45 minutes prior to the failure. This paper discusses the techniques for recording and analyzing these data and presents sane case histories.

Jan 1, 1982

By David Newman

Landslides and soil creep often occur with varying degrees of severity on steep slopes within Southern Appalachia. Ground movement may take place over years with subtle changes in topography and vegetation or it can occur rapidly in response to water inflow or disturbance at the toe of the landslide. Although the ground movement typically is restricted within the soil and colluvial layers, failure can extend into the weathered rock zone. Certain areas of Appalachia are described as "slide prone" because of historical precedent. To develop a profile of "slide prone" areas, the strength and physical properties of the soil and colluvium, topography, groundwater and surface water runoff, present and historical land use, and any surface disturbance are examined in detail. These attributes are useful in determining whether an area is potentially unstable before surface development including construction, logging, or mining. Recommendations are provided to avoid initiating ground movement concurrent with mining operations.

Jan 1, 1998

By Xun Luo

In this paper we report on the use of microseismic monitoring techniques to investigate the fracturing process associated with longwall mining. The study was carried out at three mines in Australia and concentrated on some major concerns of the mines, such as failure patterns and growth rate associated with mining progress, their implications to water ingress and gas emissions, caving processes in the goaf and precursors of roof falls. The results have shown that a zone of shear fracturing has occurred further ahead of the longwall face than predicted using conventional longwall geomechanics theory. Failure patterns in the roof and floor vary from mine to mine and this appears to be dominated by geological structures. The reaction of faults, the formation of fractures which allow gas emissions and precursors roof falls have also observed. Results from this work have opened up new understanding of longwall caving processes and proved that microseismic monitoring is a very useful technique for studies of longwall geomechanics and hazard controls.

Jan 1, 1998

By Yunqing Zhang

Roof failure occurs much more frequently at intersections than entries and crosscuts. Using a commercial finite element package, four-way and three-way intersections reinforced with the tensioned bolts are modeled. The 3-D model considers bolt pre-tension, bolt installation procedure, bedding planes and in-situ horizontal stresses. The modeling results from both four-way and three-way intersections are analyzed with regard to the intersection stability. The mechanisms of tensioned bolting at the intersections are investigated and some tensioned bolting guidelines for intersections are given. Based on this study, a better way to enhance intersection stability is to use longer bolts than entries or crosscuts and increase the bolt density near the intersection corners.

Jan 1, 2003

By Brian G. D. Smart

A scheme is presented whereby the complexities of design and operation of a hydraulically powered coalmine support are modelled using the finite element method. This enables predictions to be made of the interaction of the support with its environment in a variety of operating conditions. The model is a two dimensional representation. The modelling scheme was applied in two case studies. In the first, the performance of a four leg support was uprated by increasing the front leg force. The finite element model enabled changes in overall support performance to be verified. In the second case study, the change in lateral force developed by a two leg support was assessed with changes in support operating height and floor foundation stiffness. The modelling scheme is capable of further development with the possibility of extending the model into three dimensions and the addition of control elements that would enable an actual mining sequence to be represented.

Jan 1, 1992