Search Documents

By Ron Allum, Ed VanDerPas

The application of high speed tunneling in a deep underground copper mine is essential for an ambitious expansion project at Magma Copper Company's San Manuel Mine. At stake is the future of over 1,300 employees at the largest producing full gravity block caving copper mine in the world. A joint venture of Frontier-Kemper Constructor's Inc. and Deilmann Haniel GmbH is helping create that future through the successful application of tunnel boring technology. This paper examines the details required to assemble, deploy and operate a 4.62 m open main beam tunnel boring machine (TBM) in a 1048 m deep operating mine accessible only by shaft.

Jan 1, 1995

By Francis B. Gularte, James E. Monsees, John-Paul Whyte, Gary E. Taylor

In a short section of the Los Angeles Metro Rail system approximately 222.5 m (730 ft) of 6.4 m (21 ft) diameter twin-tube tunnels separated by a 1.8 m (6 ft) narrow pillar were designed to pass under a major eight lane freeway and a metropolitan intersection with only 3.7 m (12 ft) to 5.8 m (19 ft) of loose fill and alluvium cover. The design considerations and the chemical grouting program used to stabilize the alluvial materials is discussed. Also included is a discussion of the novel shield used for tunnel excavation and the effects of the subsequent fire.

Jan 1, 1991

By Franz Deix, Bernd Braun

A sensitive portion of Section U 6/3 of the Vienna, Austria subway system required construction of two single-track tunnels under a telecommunications facility, where strict ground settlement limitations had been set. Local geology, hydrology, and site constraints led to the decision to use the New Austrian Tunneling Method (NATM) supplemented by compressed air and partial dewatering. In addition, ground freezing was used, as the tunnel would pass through alluvial layers beneath the facility, with a cover of as little as 1.5 m. Laboratory testing and two in situ test fields were used to collect frozen soil data so that the freezing scheme ensured minimal heaving magnitude.

Jan 1, 1987

By I. Iwasaki, H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothabiliry tests and SEM observations. In the absence of sodium silicate, Ca I+ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: 1) the removal of impurity minerals and calcium-bearing precipitates from quartz surfaces by dispersion, 2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and 3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1991

By William E. Foreman

Editor's Note: For purposes of uniformity throughout this book, Coal Preparation, 5th Edition, the editors have advocated the use of the U.S.A. Sieve Series of testing sieves (see Table 6-2) as the testing sieves of modem choice. The adoption and use of the U.S.A. Sieve Series and its forerunner, the Tyler Standard Screen Scale, has for over seventy-five years introduced uniformity into reports; has simplified the comparison of results; and has provided control for operation of modem coal preparation circuits. While a full explanation of the differences, and more importantly the similarities of these two measuring systems cannot be stated here, it is felt that a brief clarification of terms is in order. The difference between the U.S.A. Sieve Series and the Tyler Standard Screen Scale Sieve Series is the identification method. Tyler Screen Scale sieves are identified by mesh designation with the width of opening varying by the square root of two, or 1.414 times the width of opening in the previous sieve. The U.S.A. Sieves are identified by openings in millimeters or microns and also arbitrary numbers which do not necessarily mean the mesh count; this series uses width of opening variations in the order of approximately the ratio of the fourth root of two, or 1.189. Tyler Standard Screen Scale and U.S.A. Sieves can be used interchangeably, and to avoid confusion the nameplate of all Tyler Screen Scale sieves show the U.S.A. Number, while all U.S.A. Sieves show Tyler Screen Scale mesh equivalent numbers on the nameplate. INTRODUCTION Sizing is the process of separating mixed mineral particles into groups of particles all of the same size, or into groups in which all particles range between definite maximum and minimum sizes. This chapter applies the modem mechanical screen and the liquid-solid cyclone (hydrocyclone) to the process of sizing solid particles as applied to coal preparation. Screening is a mechanical process that separates particles by size. Modem coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modem preparation plants is done for the following reasons: 1. Removal of fine coal before a size reduction step. 2. Size separation of the coal into a coarse and fine fraction for sized products or for processing in coarse and fine coal circuits. 3. Recovery of heavy media from heavy media coal cleaning circuits.

Jan 1, 1991

By William E. Cutcliffe, John A. Ames, John D. MacFadyen

Webster's dictionary nearly equates portland cement with its current primary definition of cement. Although such equation may be a triumph of common usage, the confusion between the terms cement and concrete unfortunately is very widespread. Full definition of cement properly would extend to many substances, but for purposes of this chapter cement is restricted to varieties of portland cement including portland-pozzolan cement. Among the usually recited historical notes concerning cement is that it was developed by the Romans. Their use of cement in the great structures of Rome, and even in the far comers of their Empire, such as Hadrian's Wall in the north of England, testifies to the antiquity of a major cement industry. From English sources we know of John Smeaton's carefully proportioned hydraulic cement mixed in 1756 and of Joseph Aspdin's patented cement to which, in 1824, he gave the name portland cement. (He claimed that his cement mortar looked like the famous dimension limestone quarried from the Isle of Portland on England's south coast.) The year 1971 marked the centennial of portland cement manufacture in the United States. A fair historical account of the many real contributors to the cement industry since 1756 unfortunately would be too extensive for this chapter. Development of rotary kiln practice and burning at higher temperatures clearly was the major move into today's technology. Cement manufacture is the processing of selected and prepared mineral raw materials to produce the synthetic, mineral mixture (clinker) that can be ground to a powder having the specified chemical composition and physical properties of cement. Cement making incorporates a number of distinct steps, but it is characterized by the key pyroprocessing (or burning) step, which brings about the necessary changes in the raw materials. This pyroprocessing is a chemical process. Conversion of large volumes of mineral raw materials into specification-controlled cement at relatively low cost is the objective. Statistics on the cement industry are of uneven quality. The US Bureau of Mines (USBM) is the principal collector of available data. These statistics can be only as good as the quality of information supplied by the reporting companies. The data perhaps most often questioned relates to productive capacity of the industry. The questions submitted by USBM are valid, nevertheless, and the information gained from them, as good as is available, is what is generally used. The Portland Cement Association also is a source of much quality information. In analyzing cement industry production rates, it is well to keep in mind that measurement of raw materials requires the reader to recognize that approximately 1.6 t of dry raw materials are required to make 1 t of clinker. This number can vary depending on the amount of kiln dust wasted. Also that to produce 1 t of portland cement required .94 to .96 t of clinker, the remainder being gypsum or anhydrite. A ton of masonry cement or pozzolanic cement re- quires considerably less clinker.

Jan 1, 1994

By Richard Dunmore

Most coal seams in the United Kingdom contain firedamp, some of which is released into the ventilating airways as the strata around a working relax. The close sequence of seams in carboniferous strata is usually such that seams in adjacent roof and floor strata are also disturbed and potentially large quantities of firedamp can enter the workings from these sources. Since emission depends on the disturbance rate of the seams, higher coal production rates associated with increased mechanisation in the colliery accentuate the problem. Firedamp concentrations in UK underground workings are subject to statutory regulations1. To enable production to continue uninterrupted and in safety the problem is tackled by ventilation engineers by the provision of adequate ventilation in the airway and by the technique of firedamp drainage. In the UK the latter usually takes the form of cross-measure boreholes in roof strata, and increasingly also in floor strata, drilled from the gateroads, especially from return airways. In this way firedamp emitted from disturbed seams in adjacent strata can be extracted directly to the surface or to some safe position outbye, and the airways of the working district are not contaminated. Despite the use of firedamp drainage, considerable quantities of firedamp enter the ventilation air- stream and the concentration levels may be seen to be related to the coal production activites in the district. Figure 1 shows a typical recording of methane concentration obtained by a BM1 methanometer at a position outbye in a return gate where firedamp drainage was operating. The general rise in level throughout the working week may be seen, together with peaks occurring during production shifts and the gradual decay of emission over the weekend. In view of the fact that ventilation and firedamp drainage contribute a considerable proportion to the operating costs of the colliery, it is essential that the ventilation and firedamp drainage requirements be calculated as accurately as possible at the planning stage of the working. In the past the ventilation engineer has had to rely heavily on experience in neighbouring workings but with the development of mines in previously unworked areas there is clearly a need for a methodical approach to meet the requirements of planning. The work described in this paper represents such an approach and it is hoped that successful development and application of the method of prediction will lead to the widespread adoption of a routine procedure. The current development of a method of prediction of firedamp emission into longwall workings is based on the theoretical treatment of gas emission from coal seams proposed by Airey2 in 1971, which was based on his study of gas emission from broken coal 3 which was published in 1968. In common with other experimental methods of prediction, the method enables a calculation to be made of the total make of gas emitted from all sources of gas in the strata per tonne of mined coal.

Jan 1, 1980

By Michael L. Cramer, Kunsoo Kim

INTRODUCTION The Columbia River Basalt beneath the Hanford Site is one of several rock types being considered by the U.S. Department of Energy for the first commercial high-level nuclear waste repository. The Basalt Waste Isolation Project (BWIP) has been carrying out a comprehensive investigation to assess the feasibility of constructing a repository in basalt and to develop technology required for repository engineering and site characterization. Development of a nuclear waste repository requires a number of design considerations not usually necessary in the planning of conventional underground structures. Principal among these is the thermally induced stress field resulting from waste emplacement. This thermal stress, super- imposed on the preexisting in situ- and excavation- induced stress fields, needs to be evaluated in the design process due to the sensitivity of waste emplacement density to this factor. The nature of this thermally induced stress field is dependent on several factors, including the temperature distribution around the repository openings, the thermal properties of the rock mass, and the deformability of the rock mass. Re1iable performance of the repository structure is largely determined by the ability to under- stand the above rock mass characteristics and predict the underground opening response to waste emplacement based on this understanding. To gain an understanding of this rock mass behavior in a repository condition, the BWIP has conducted a large-scale heated block test in basalt at the Near-Surf ace Test Facility (NSTF) on the Hanford Site. This paper presents the results from the elevated temperature phase of the block test in which the thermal, mechanical, and thermo- mechanical response of the closely jointed basalt rock mass was evaluated as a function of stress and loading orientation at varying temperatures up to 200 oC. SITE GEOLOGY The NSTF test areas, including the block test site, are located in the entablature zone of the Pomona basalt f low. The Pomona flow entablature is structurally typical of most flows in the Columbia River Basalt Group in that it is characterized by long, undulating, polygonal columns up to 2.4 m in length. Columns vary from 15 to 30 cm in diameter, averaging about 20 cm. Over their length, columns can vary in dip by 150 to 200. The column structures are dissected by subhorizontal cross joints that are generally discontinuous and seldom cross columnar joint boundaries. Spacing of the cross joints also averages about 20 cm. A representative joint pattern taken from mapping of the tunnel wall near the block test site is shown in figure 1. Application of the Rock Mass Rating System (Bieniawski, l979) to the block test site yielded an overall value of 62. The corresponding value from application of the Q-system (Barton et al., 1974) is 8.7 (Cramer and Kim,1985). The NSTF is approximately 50 m below the surf ace. However, this depth is sti1l above the water table and conditions are generally dry. Interstitial water exists as the result of percolation of meteoric water from the surface.

Jan 1, 1986

By G. Gregory Bryan

G. GREGORY BRYAN 33.1-DEFINITIONS 1. Engineering-Engineering may be defined simply as the science and art of making materials and energy serve the purposes of mankind. There are many fields of engineering, each with specialized branches. The basic fields are: civil, mechanical, electrical and chemical. Others may be specialized phases of one of these or a combination of two or more of them. Mining engineering, for example, requires a working knowledge of construction, mechanics, electricity, metallurgy, geology, accounting and economics, in addition to mining techniques or methods. Mining geology and geological engineering involve rocks and their structure and the forces that act upon them, and chemistry, physics and mechanics also are important to practitioners in these fields. Metallurgical engineering requires chemistry and physics but also a working knowledge of mechanics and electricity. The fields of engineering with which this section are concerned are those primarily involved in the finding, mining, processing and utilization of the natural mineral resources of the earth. They include geology, mining engineering and metallurgy, each with several specialized subdivisions. 2. The Engineer-The engineer is an individual who has had specialized training to qualify him to practice the profession of engineering. The term engineer is used here in its broadest sense to include such professions as certain applied branches of geology, physics and chemistry, whose practitioners may not have acquired engineering degrees but who, nevertheless, by training and experience in some area of the minerals industry, qualify under the above definition. To become a successful engineer, a person should have certain pronounced aptitudes and preferences, even before embarking upon the requisite course of training. Among the chief qualifications that the engineer-to-he must possess are: (a) a natural inclination toward mathematics and the physical sciences, and (b) intellectual and moral honesty. Among the qualities the student engineer must develop are: (a) independence of thought, open-mindedness, sound judgment and the ability to observe, deduce, plan and apply solutions, (b) the ability to articulate and convince, and (c) the ability to organize and direct the activity of others. These qualities are normally developed through sound education, followed by pro¬gressive experience. 3. The Consulting Engineer-The consulting engineer is an engineer primarily in the business of furnishing specialized advice and engineering services on an intermit¬tent, part-time or occasional basis to clients who do not have continuous or full-time need for those services. He must be able to make and take full responsibility for decisions and recom¬mendations where original thought is required. He should not be confused with the engineer, surveyor or technician who also may furnish services on an intermittent basis, such as regular periodic surveys, the overseeing of drilling programs and other such routine work as may require little original thought and planning. 33.2-THE PROFESSION OF CONSULTING ENGINEERING 33.2.1- QUALITIES REQUIRED A successful consulting engineer must first have, as a minimum, the qualities and preparation of an engineer. In addition, he must have sufficient knowledge,

Jan 1, 1973

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined, because it is used in three ways: 1) as a diverse group of fine-grained minerals, 2) as a rock term, and 3) as a particle size term. As a rock term, clay is difficult to define because of the wide variety of materials that comprise it; therefore, the definition must be general. Clay is a natural, earthy, fine grained material comprised largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates comprised mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many definitions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic, e.g., halloysite and flint clay. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on various grade scales. Soil investigators and mineralogists generally use 2 pm. as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than approximately 4 pm. Some authorities find it convenient to use the term clay for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or argillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally understood by those who use it. Clay is an abundant natural raw material, and it has an amazing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial minerals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1988, 1989, and 1990 productions according to the US Bureau of Mines (Ampian, 1992). As industrial minerals, clays are a complex group that consists of several mineral commodities, each having somewhat different mineralogy, geologic occurrence, technology, and uses. In this section these commodities are organized as follows: 1) bentonite, 2) common clay, 3) hormites, and 4) kaolin. Fuller's earth is discussed in both the bentonite and hormite chapters. Fuller's earth is a term based on use, and both bentonites and hormites are sold as fuller's earth. The overlapping is particularly evident where both bentonite and non-bentonite fuller's earth are used for the same purposes or products, such as in drilling mud, bleaching or clarifying fats and oils, and carriers for insecticides and fertilizers. Kaolin, ball clay, halloysite, and refractory clays are grouped together because they consist mainly of minerals of the kaolin group. Common clay is a grouping of several fine-grained materials, including shale, sometimes referred to as miscellaneous clay. The scientific and technological publications pertaining to clays

Jan 1, 1994

The latest resource estimate for the Caspiche gold/silver/copper project in the Maricunga region of Chile was released by gold explorer Exeter Resource Corp. The resource is low grade, but bulk minable and drilling to date has shown a NI 43-101 compliant inferred resource of 1,117 Mt (1.23 billion st) grading 0.55 g/t (0.016 oz/st) gold, 3.81 g/t (0.111 oz/st) silver and 0.22 percent copper. Exeter said these findings make the in situ metals amounts of 609 t (19.6 million oz) of gold, 4.4 kt (137 million oz) of silver and 4.84 billion lbs of copper, which the company relates as 33.7 million gold equivalent ounces using assumed metal prices of $23.33/g ($800/oz) for gold, 35 cents/g ($12/oz) for silver and $2/lb for copper. The deposit is almost midway between Barrick?s Cerro Casale gold deposit and Kinross? Refugio Mine. In a statement Exeter chairman Yale Simpson said ?This updated resource estimate places Caspiche firmly among the world?s largest gold-copper discoveries in recent years and clearly supports our decision to aggressively drill the property, despite the global economic decline. ?We expect that the very substantial copper and silver credits will be extremely important, and will markedly impact the potential viability of Caspiche. Specifically, using metal prices of US$2/lb copper, $23.33/g ($800/oz) gold and 35 cents/g ($12/oz) silver, the 4.84 billion lbs of copper and 4.2 kt (137 million oz) of silver are equivalent to 376 kt and 62 t (12.1 and 2 million oz) of gold, respectively. ?Our recent drilling has defined what appears to be a coherent higher grade central zone associated with a definable early stage diorite intrusion. We expect this zone will be important in developing various mining and economic models for the project,? Simpson said. Exeter is still drilling the deposit to expand the re-source estimate further to the southeast and at depth and to upgrade the higher grade central zone to the indicated category. Simpson said, ?Exeter intends to enhance the value of Caspiche by continuing to de-risk the project through ongoing exploration, metallurgy, engineering, water and environmental studies. These studies will continue through the next 12 months and will lead to a conceptual development study. A timeline for the release of that study is being formulated. The project budget for the next 12 months is C$14 million.? Mineweb reported that Caspiche is likely too big of a deposit and at too high of altitude for Exeter to handle alone. Exeter will be looking to other majors, or perhaps the Chinese, to help develop this huge orebody. But, in the meantime, it also has its high grade Cerro Moro deposit in Argentina, which could be brought to production relatively quickly and at relatively low cost.

Jan 1, 2009

By Sharanappa Yalal, Rakesh Kumar Khali

"Himalayan geology poses the most challenging ground conditions almost anywhere in the world, one of the reasons thereof is their evolution as the youngest mountain chains. They are demonstratively rising faster than any mountain elsewhere. The composition is also younger, and consequently less well consolidated than the other older fold belts. This is consistent with the fact that they constitute one of the most active of the plate margin zones rising at a rate that is almost double the Andes, which is in turn three times that of the Alps. Thus, stress conditions (Magnitude and variations) can potentially be more extreme and adverse on a Himalayan tunneling project. Tunnel excavation under the Himalayan Mountains will pose significantly more challenges than an equal length and equal cover drive almost anywhere in the world. These in-depth-tunneling difficulties through high mountainous terrains have posed major challenges for application of traditional drill and blast (D&B) and NATM methods. Handling such adverse geology at any depth is always problematic and generally leads, if not adequately foreseen, to the significant tunneling delays. The author wants to highlight the challenges faced and on the spot solutions adopted while executing most prestigious 273Km long Udhampur –Srinagar- Baramula Rail Link Project (USBRL) in the Himalayas in the state of Jammu & Kashmir, India. The main focus of the paper is on main stretch of USBRL Project i.e. T-80 (India’s 2nd longest railway tunnel & 3rd longest in Asia) where the team of the author has recently completed a 11.2 Km long tunnel and where the train track has gone operational from Qazigund to Banihal. The construction of this stretch posed several challenges akin to highly adverse geological conditions. Executing on -the -spot solutions, the project has been completed successfully. 1.0 INTRODUCTION Construction of Udhampur-Srinagar-Baramulla Broad gauge railway line is one of the Mega projects undertaken by Indian Railways to establish a dependable transportation in the state of Jammu and Kashmir. In engineering terminology, it is a challenging project negotiating breakthroughs against the complex Himalayan geology. The Project which has been operational over last 12 years , stretch by stretch, is in advance stage of construction . The purpose of the prestigious project is to connect the Kashmir valley to the mainland of the state of the country. On the date owing to the hurdles of the tuff terrain, the transport of this part is totally dependent on the surface transport, i.e., through a road which connects NH-1A from Delhi to Srinagar. The altitude of the region varies from 500.00 to 1700.00, ranging through Udhampur to Katra - Reasi –Sangaldan- Banihal-Quazikund-Ananthnag-Srinagar-and Baramulla. The main features of this project are its Pirpanjal Tunnel and T-48 & 49 tunnels which cover the maximum length of tunneling through thick hostile geological conditions, the total length being 138km. Details of Pirpanjal tunnels are shown in Figure-1."

Jan 1, 2016

By Chen Bing Ching

Hsikwangshan mine is located at Lengshuijiang city of Hunan Province. It is a stibnite deposit. The orebody is gently inclined; its ore run is about 3 km in length and extends about 1.2 km along the direction of dip. The thickness of the ore body is non-uniform and varies from 1.5 to 20 m. The orebody is mined by room and pillar and cementation filling. The nine levels at the ore top have been mined out. At present, the mining operations are at the eleventh level. The mine ventilation system consist of three main fans which are installed in different shafts and are ventilated in parallel. The main fans can be connected to each other through comprehensive return air drifts. Two of the fans are located underground and the other on the surface. The general configuration of the ventilation system is shown in Figure 1. Because the operating areas are scattered and vary frequently as well, it is difficult to bring about air flow control. If the air flow cannot be varied with the variation of production in time, the air quantities are not sufficient in some areas and are excessive in others. However, it is also a problem to coordinate the three main fans with one another to obtain the optimum economic cost of operation. In order to make the air delivery fit the variation of production continuously to satisfy the ventilation requirement of the working faces and to reduce power consumption, we have made a great effort over five years to install an automatic control system for mine ventilation at the Hsikawangshan mine. The key part of this system is a microcomputer. The whole system consists of a console, which is located at the surface; the circuit network that is provided for signal transmission; air doors and ventilators at the working face; the scale air doors which are installed at the main branch airways; main fans and their speed regulating devices, as well as the sensors used for observing pressure, air quantities, temperature and the concentration of carbon monoxide, etc. This system can continuously telemeter the air quantities and carbon monoxide concentration in the main branch airways, air pressure, air quantities, electric current, the temperature of the bearings of the main fans, etc. According to the production air requirements, the system controls the ventilators or air doors which are located at the working faces and regulates the air quantity in the main branch airways. It can also choose the optimum mode of operation automatically, and regulate the rotating speed of the main fans to guarantee the least total power consumption while satisfying the total air quantity requirements. If abnormality of the observed results is discovered, the audible and flashing light alarm signal starts up automatically. The operating mode of ventilation equipment also feeds back to the control room and displays on the console. The configuration of control the system is shown in Figure 2.

Jan 1, 1987

By C. C. Harvey

Based on resource studies in many developing countries, four categories of industrial clay resources are recognized as precursors to development strategies. Category I: High quality, high technology clays requiring major investment for large tonnage international markets. Category 2: Unique specialty clays requiring advanced technologies for small tonnage niche markets. Category 3: Lower technology, moderate quality clays, predominantly to supply local markets. Category 4: Low quality clays requiring little or no processing. Projects with Categories 1 and 2 clays require extended development times (green field to investment decisions) with significant pre-development investment, while projects with Categories 3 and 4 clays require shorter development timetables and lower levels of investment.

Jan 1, 1998

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles) northeast of Winnemucca, Nevada. The deposit is owned by First Miss Gold Inc. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 m (1 400 ft.) to 671 m (2 200 ft.), along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate within the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By A. F. Edwards

The Main Pass sulphur and oil deposit is located at Main Pass Block 299 in the Gulf of Mexico, 30 miles east of Venice, Louisiana, in 210 feet of water. The deposit was discovered by Freeport-McMoRan and its joint venture partners, IMC Fertilizer and Homestake Mining, in late 1988-early 1989. The sulphur deposit contains 67 million long tons of recoverable sulphur. The sulphur occurs in bio-epigenetic limestone replacing anhydrite caprock on top of a salt diapir. Recoverable reserves of 39.4 million barrels of oil and 9.1 billion cubic feet of gas are also contained in the limestone caprock and in supracap sandstone stringers.

Jan 1, 1992

By J. P. Earnhardt

Recycling of such municipal solid wastes as glass containers, metal cans, and newspapers has received increasing attention recently. However, municipal solid wastes account for only 1% of the total solid waste stream in the United States. The remainder includes hazardous and non-hazardous industrial wastes. Generators of industrial wastes are facing higher landfill costs. Future liability potential, and public image concerns which are forcing them to seek innovative and often profitable solutions to minimize, reuse, and recycle their waste streams. Opportunities for the mining industry in industrial recycling include recovery of mining wastes and by-products, and utilization of mineral products for treating waste streams.

Jan 1, 1993

By Eric Hansen, Todd Wanless, Chris Mueller, Shannon Dunne, Scott Elmer

Between 2010 and 2018, Houston added more than 1 Million residents; the third largest rate of growth in the nation. With growth, the region faces new challenges with water supply, capacity of its wastewater system, and regional drainage. While tunnel construction has been limited in Houston since the Clean Water Program of 1990s, it is about to see a resurgence to improve water supply reliability and to reduce flood risks and sanitary sewer overflows. This paper examines the challenges with “going deep” below the built urban environment and related to high ground water; stiff, fissured clays; flowing silts and sands; faults; hazardous materials; and abandoned well fields.

Jun 13, 2021

The Penetrating Cone Fracture (PCF) technology 1 is a new method of rock excavation developed by Sunburst Excavation, Inc. of Denver, Colorado. PCF is a rock excavation method which employs tensile breakage mechanisms under controlled conditions to enable the continuous excavation of rock?in underground and some surface applications. The technology has developed rapidly over the last two years to the point where it is now being prepared for commercial application in the mining and civil construction industries. The initial commercial application of PCF will be undertaken at the Perseverance Nickel Mine of Western Mining Corporation Limited in Western Australia beginning in May, 1994.

Jan 1, 1994

By Ing. H. Kellerwessel, Ing. M. Esna-Ashari

This paper refers to the new crushing and grinding process, invented by Professor Schonert (Ref. 1), Clausthal, Germany. The process is known as high pressure particle bed comminution or interparticle crushing. Several papers already describe fundamentals of the process, the equipment used, results of lab size and large scale tests and the first results of commercial operations (Ref. 2 to 7). Of course, we will treat the topic from the perspective of a downstream gold ore upgrading or leaching process. Some recently executed testwork indicates that the process provides special advantages in this field. To describe the process generally, in view of the already existing publications.

Jan 1, 1998