Search Documents

By V. C. Kelessidis

Demand for multifunctional drilling fluids continuously increases. In the quest for more hydrocarbons, drilling has extended to deep water areas (now in excess of 2.000 m) and to very deep wells (now in excess of 6.000 m). In these extreme conditions, low temperatures, as low as 1-5°C on the sea bed, high temperatures, in excess of 200°C, and high pressures, more than 1.000 bars, in the bottom of the well, are frequently encountered. In these harsh environments, synthetic oil and oil based drilling fluids are used, but the former are expensive while strict environmental requirements have limited the use of the latter. Thus, drilling industry has turned back to water based drilling fluids which use bentonite as primary viscosifier and as a fluid loss control additive. However, in conditions of high temperatures, bentonite suspensions gel and loose their exceptional low temperatures properties, thus, additives are needed to overcome such problems. In this article we review these challenging drilling environments and establish the requirements for the multifunctional drilling fluids. Our research indicates that demand for continuing use of bentonite by drilling fluid industry is strong. Furthermore, we bring forward the opportunities for new additive development which can expand the operational ranges of bentonite suspensions.

Jan 1, 2007

By Eugene F. Casey, John G. Ruggiero

INTRODUCTION Construction of tunnels in urban areas, especially reclaimed areas, pose many problems. The Red Hook Intercepting Sewer Tunnel, Contract 1A is a portion of the Red Hook Water Pollution Control Project located along the Brooklyn waterfront in New York City. This contract required the construction of a 2620 meter long (8600 L.F.), 3 meter (10-foot) diameter soft ground tunnel, eight Tunnel Manholes, nine Regulator structures, four Diversion and Tidegate structures and 765 meters (2500 L.F.) of branch intercepting sewers of diameters between .30 meters (12 inches) and 1.8 meters (72 inches). The construction contract bid price was $62 million with a duration of three years. The tunnel route crosses over five sets of operational twin cast iron subway tubes with clearances ranging from 4.3 meters (14 feet) to as small as 0.35 meters (14 inches). The route of the tunnel traverses historically interesting areas which have been reclaimed over the last 200 years. This paper is a case history describing the contractor's methods utilized to successfully advance the work through the above problem areas. LOCATION The Red Hook Intercepting Sewer Tunnel is located in the Borough of Brooklyn of New York City. The route is

Jan 1, 1981

By C. P. Lazzara, R. W. Pro, A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effectiveness of automatic water sprinkler systems in the extinguishment of incipient conveyor belt fires under ventilated conditions. Large-scale experiments were conducted using a double strand conveyor belt configuration. Standard response, pendent-type sprinklers, with activation temperatures of 100°C, were installed above and between the two strands of belting, in accordance with Federal standards for sprinkler system installations in belt drive areas. Experiments at airflows of 1.1 and 4.6 m/s showed that the sprinklers activated later, the peak heat release rate was larger, and more betting was consumed at the higher airflow. In experiments with 74°C, fast response, directional sprinklers, the sprinklers activated at the same heat release rate for both high and low airflows, but the peak heat release rate and amount of bett consumed was slightly higher at the lower airflow. Experiments were also conducted with 100 °C, standard pendent sprinklers installed above the top belt, in accordance with the National Fire Protection Association (NFPA) Standard 123 for sprinkler system installations in conveyor belt drive areas in underground coal mines. In these experiments, the heat release rate and amount of betting consumed was larger at the higher airflow.

Jan 1, 1995

By Kenneth S. Johnson

High-purity gypsum of Permian age crops out in three major gypsum districts of western Oklahoma. The northwest and southwest districts have important reserves in the Blaine Formation, whereas reserves of the west-central district are in the Cloud Chief Formation. Gypsum beds of the Blaine Formation typically are 10 to 30 feet thick, 95 to 99 percent pure, and interbedded with shales that are 2 to 30 feet thick. The base of the Cloud Chief Formation consists of a massive bed of gypsum that typically is 20 to 100 feet thick and is 92 to 97 percent pure. Anhydrite is present in the sulfate beds, beneath 20 to 100 feet of overburden, at a number of places in all three districts. Total gypsum reserves in the three districts are estimated at 48 billion short tons. These reserves are well suited for open-pit mining or quarrying, because gypsum typically forms hills in the semiarid climate of western Oklahoma, and the gypsum layers are nearly flat lying, without folds or faults. Seven companies currently mine a total of 1.0 to 1.4 million tons of Oklahoma gypsum each year for wallboard, for plaster, as a retarder in portland cement, and as a soil conditioner.

Jan 1, 1978

By Frank E. Kottlowski

Widespread high-calcium (HC) limestones in New Mexico and adjoining areas, are low in magnesium, but some units include shale interbeds that would be deleterious for usage in sulfur removal. In southwest New Mexico, southeast Arizona, and adjoining parts of Mexico, limestones in the thick Mississippian Escabrosa, Pennsylvanian-Permian Horquilla, and Cretaceous U-Bar units are HC as are strata in the Mississippian Lake Valley, Pennsylvanian formations, Permian Hueco, and parts of the Permian Capitan Limestone of south-central and southeast New Mexico and west Texas. In north-central and central New Mexico, many limestones in the Pennsylvanian Madera Formation are HC as are some of the Cenozoic travertines. In northwest New Mexico, where the present-day mine-mouth coal- fired power plants occur, there are no HC limestones, but to the north in southwest Colorado some beds of the Mississippian Leadville Limestone and Pennsylvanian Hermosa Formations are HC. HC limestones considered contain at least 95 percent calcium carbonate and less than 3 to 5 percent magnesium carbonate. Limits for other impurities are alumina, 1 percent; silica, 2 percent; sulfur 0.05 percent; phosphorous, 0.02 percent; and iron oxide, about 1 percent. Chemical and physical requirements differ slightly depending upon the ultimate use.

Jan 1, 1995

By Timothy C. Smith, S. Andrew Jacobs, Douglas E. Gonzales, Sandy J. Schexnailder, Carl Urban

At the Schwartzwalder Mine (Cotter Corporation, Golden, Colorado) ion exchange resins have been used in mine water treatment experiments. The experiments, initiated in October 1979 and currently in progress, demonstrate that mine water uranium values can be reduced to levels as low as 10 ppb. Duolite® A-101D, a strongly basic anion exchange resin, was tested in laboratory-scale columns (1 inch diameter) initially and then in pilot-scale columns (4 inch diameter), using both co-current and counter-current operational modes. Observations and conclusions resulting from these studies can be summarized as follows: (1) Duolite® A-101D appears to have successfully extracted uranium at influent levels of approximately 2.0 ppm over multiple loading and elution cycles, consistently producing effluent concentrations as low as 10 ppb uranium. (2) Based upon present test data, counter-current regeneration appears to be the key to successful operation. Upflow loading and downflow elution are the preferred modes for service and regeneration, respectively. (3) Filtration is a necessary pretreatment to remove fine clay and inorganic precipitates that will foul the resin, causing excessive pressure drop and poor loading and elution kinetics. (4) This waste treatment application is unique in that it offers the opportunity to recover some or all of the capital investment in the treatment facility

Jan 1, 1980

By Terry S. Maley

With some exceptions, minerals may be acquired on the unappropriated public lands by one of three methods: (1) mining claim location under the General Mining Law of 1872; (2) mineral lease under the Mineral Leasing Act of 1920; and (3) sale contract under the Mineral Materials Act of 1947. Leasable minerals such as oil, gas, coal and phosphate are specifically designated as leasable in the Mineral Leasing Act so the method of acquisition is clear. As a general rule, metallic minerals are acquired by mining claim location. However the nonmetallic minerals, most of which are industrial minerals or gemstones, present a more difficult problem. These minerals are acquired either by mining claim or a sale contract depending on their chemical composition, physical properties and the use to which they are put. The Act of July 23, 1955 (30 U.S.C. 61 1) provided that uncommon varieties of sand, stone, gravel, pumice, pumicite or cinders are locatable; whereas, common varieties of such minerals may only be acquired by a contract of sale. The widespread location of mining claims to appropriate such deposits has caused many land management problems. Federal court and Interior decisions offer the most useful guidelines in determining the most appropriate method of acquisition.

Jan 1, 1991

By B. Morris

This presentation will describe the process by which the Quebrada Blanca (QB) copper project in northern Chile was financed. It will also show how a relatively junior mining company addressed the problems created by its inability to provide its share of the equity funding and the guarantees required by the project lenders. QB is located in the semi-arid Andean highlands of northern Chile, 170 kilometres southeast of the port of Iquique and 30 kilometres west of the border with Bolivia, at an altitude of about 4,300 metres (14,000 feet). Figure 1 depicts the project's location. The QB orebody is a secondarily enriched porphyry copper deposit containing reserves of 85 million metric tons grading 1.3 percent copper. Underlying the enriched zone is a significant primary ore zone containing several hundred million metric tons grading about 0.5 percent copper. In the late seventies and early eighties Falconbridge and its affiliates spent $20-30 million dollars exploring the deposit and conducting feasibility studies. For a variety of reasons they decided not to develop the property which was returned to its owners, Empresa Nacional de Mineria (ENAMI), which is a Chilean state mining corporation. In 1988 ENAMI announced its intention to privatize the property through a public bidding procedure.

Jan 1, 1993

By Alberto Tarsitani

The existing Rome-Florence railroad capacity is inadequate for the traffic volume. To increase this capacity and to reduce the traveling time the Italian National Railroad Administration has decided to provide an additional 400% of rail capacity. This new rail line will be known as the Direttissima Roma-Florence line. It is planned to operate the trains on this connection at speeds of 250 km per hr. Table 1 lists the main design characteristics. [TABLE 1. Design Characteristics Design speed250 km per hr Maximum inclination80 00 (0.8%) Minimum curve radius3000 m Minimum vertical curve radius30,000 m Maximum superelevation in curve 425 mm Type of rail60 kg per m welded] The new rail line will be connected to the existing one by means of high speed switches called "interconnections" so that parts of the new line can be used also by local trains. Construction works for this new line have been divided by the railroad administration into eight sections. Five of these have already been committed to joint ventures. Castiglione Tunnel is a part of the fifth section, 42 km in length, which has been awarded to Consorzio Ferrofir which is a joint venture composed of the construction firms of Astaldi - Di Penta - Lodigiani - Sogene.

Jan 1, 1974

By Bastiawarman Rifki, Nugraha Nico, Priatna Anton

The Deep Mill Level Zone (DMLZ) is one of the underground mines operated by PT Freeport Indonesia (PTFI). DMLZ is located approximately 1,500 m below ground level, where dominant rock types are skarn and diorite. The DMLZ mine and layout was designed based on the previous mine located above ground, the Deep Ore Zone (DOZ). The DOZ mine, located approximately 1,000 m below ground level, was a proven success, with a maximum capacity of 80K tonnes per day. During the production ramp up, which started in 2015, the DMLZ experienced several seismic events. The most significant event occurred in January 2018 with a recorded magnitude of more than 2.0 Mw, which resulted in a 14-month delay of the undercutting until March 2019. The significant event in January 2018 required the DMLZ to apply several adjustments related to the mining plan to help ensure it could continue development and achieve production target safely. This paper will describe the changes in the DMLZ mine plan as a response to the seismic activity at the mine, the reason behind the decisions being made to change the mine plan and strategy, as well as strengths and weaknesses between the previous plan compared with the new plan.

Apr 26, 2022

By C. J. Newman

Prior to 1995, the smelting process at the Kennecott Utah Copper Corporation (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. In the consideration of expansion opportunities, the existing process did not lend itself to a program geared towards processing the total output of KUCC mining and milling operations. During 1989 and 1990, a number of smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1.0 million tonnes per year of copper concentrate, with the ability to expand to 1.2 million tonnes per year. Following the shutdown of the smelter facility utilizing the Noranda technology in May 1995, the flash smelting furnace commenced operation in June with the flash converting furnace startup following a few weeks later. The smelter has achieved design production targets and environmental goals. Current operating rates are at or above design rates for concentrate and matte processing. Emissions are lower than the permit levels and equate to less than 3.5 kg of S02 per tonne of copper. This paper outlines the design, construction, startup and the first two years of operation of the modernized KUCC smelter.

Jan 1, 1998

By L. A. Price

With increased stripping ratios and with dwindling ore content, the mining fraternity is increasingly turning to larger and larger equipment for profitable open pit operations. The availability of higher horsepower prime movers and increased capacity electric transmissions using either wheel mounted or axle mounted traction motors makes a reality of single axle, rear dump trucks having 150 to 250 ton capacity. The size of electric loading shovels is inherently geared to the size of haulage equipment. To work effectively with this new generation of trucks, the Harnischfeger Corporation has introduced its P&H Model 2800 with a capacity of 20 to 25 cubic yards and a working weight of nearly 1,500,000 pounds. The Model 2800, depicted in Figure 1 loading a 200 ton truck, has many new electric and mechanical features designed to give excellent production and low cost operation. Chief among the new features is the ELECTRO TORQUE* control system. ELECTROTORQUE is a completely static, solid state electronic system supplying controlled power both to the armature and to the fields of the d.c. shovel drive motors. It eliminates many major electrical rotating machines and their attendant maintenance. The system was developed jointly by ASEA of Sweden and Harnischfeger Corporation.

Jan 1, 1969

By C. G. Cunningham

The Marysvale volcanic field of west-central Utah contains large areas of argillically altered rocks (fig. 1) that, in turn, enclose smaller areas of fine-grained, medium-grade, replacement alunite deposits and coarsely crystalline, high-grade vein-type alunite deposits. The largest replacement alunite deposits are [ ] located peripheral to a 23-m.y.-old monzonite stock called the Central Intrusive (fig. 1). The deposits formed in near-surface, highly oxidizing environments at the tops of hydrothermal plumes that were spaced irregularly around the stock. The deposits are horizontally zoned from alunitic cores through kaolinitic to propylitic envelopes. Vertically, characteristic alteration minerals progress from a pyrite-propylitic alteration assemblage at the base, upward through alunitic, jarositic, and hematitic assemblages to a flooded silica cap as shown on figure 2. The silica caps are cut by hydrothermal explosion breccias. d34Sso4 values of + 11.5 to + 15.4 permil indicate that sulfur in the hydrothermal plume was derived from underlying Mesozoic evaporites. The sharp upward transition from pyrite- propylite to alunite probably marks the paleowater table, and the top of the flooded silica cap represents the paleoground surface. Basin-Range extensional tectonism began shortly after alteration, and buried the replacement alunite deposits in basins beneath sediments eroded from uplands. The deposits were only recently exhumed.

Jan 1, 2013

By D. A. Dahlstrom

Energy costs have had a serious impact on all basic industries today. This is due to the significant amount of energy that is used to convert natural resources into usable products. Other factors such as transportation with its major energy requirement and materials employed in processing that have already required significant energy input for their manufacture accordingly influence delivered cost to the user. The farmer is a good example of this. While his large capital investment for land, machines, and buildings is highly impacted by today's interest rates, his chemical fertilizer, herbicides, and pesticides as well as those same machines and transportation costs for his products have also been seriously affected by energy costs. With the many unit operations involved in mining and mineral processing, several of which require significant inputs of energy, one can only conclude that this industry has experienced a great increase in percentage of total cost for energy alone. Fuerstenau (1975) indicated that the minerals industry used about 12.5% of the total energy produced in the US. McNulty (1983) listed the total energy requirements for the production of 0.9 t (1 st) of various metals including the energy consumed in the manufacture of supplies employed, such as tires, explosives, chemicals, grinding media, etc. (Table 1).

Jan 1, 1987

By J. A. Herbst, L. B. Hales, R. Zaragoza

INTRODUCTION The Control Problem The need for automatic control in flotation plants stems from frequent and randomly occurring disturbances to the feed slurry. Typical disturbances occur in the solids feedrate, the slurry percent sol ids, and the mineralogy and flotability of the gangue and valuable minerals. In plants where semi -autogenous grinding mills (SAG) are used, feedrate changes are very large and changes in feed percent solids of 1m or more are common. Mineralogy changes between valuable minerals are common, as are changes in the host gangue rock. As these changes occur, the operator can attempt to compensate for them by making adjustments to the flotation cell levels, the dosage rates of the collectors and frothers, the pH, and in some cases the aeration rate of the cells. This problem is sometimes complicated by the fact that different sections of the flotation plant will be processing different ore types at the same time. Potential Savings with Control Flotation control brings about savings or plant improvements in two areas; the first is in improved metallurgy and the second is in reagent savings. Improved metallurgy includes increases in the average plant recovery and achieves target concentrate grade level s more consistently. Average recovery increases between 1.0 and 5.0 percentage points have been widely reported (Paakkinen, 1979; Sutherland, 1984). Reagent savings of up to 40 percent have also been reported (Hales, 1985). VARIABLES OF IMPORTANCE Control led, Manipulated, and Disturbance Variables The initial step in the analysis of the flotation control problem is identification of important variables which can affect the efficiency of separation. The efficiency of separation is represented by a group of controlled variables which can quantify the performance of a flotation circuit. This group includes variables such as grade, recovery, tonnage through- put, and circulating loads. The efficiency of separation of a flotation circuit may generally be defined by a grade recovery map, where each point on this map re- presents a set of operating conditions (see Figure 1). However, the combination of operating conditions must be set to operate close to the economic optimum. The group of operating variables which are changed in order to achieve desired circuit performance are called manipulated variables and can be classified into two

Jan 1, 1986

By W. J. C. Meynink

In drier regions of the world, total containment of cyanide liquors for rainfalls less than a specific design value is often required by government regulation. For example, in Queensland total containment is required for rainfalls up to 'the 1% annual exceedence probability. In equatorial regions, where rainfall greatly exceeds evaporation, a total containment requirement is unrealistic and this is recognized by regulatory authorities. Regulatory constraints typically require that cyanide concentrations at an agreed downstream compliance point not exceed a specific value more than a specified fraction of the time. While the excessive rainfall prevents total containment, it does provide substantial dilution. This paper outlines a methodology for assessing the distribution of cyanide concentrations at a downstream compliance point in an equatorial region with limited hydrometeorological data. Consider the hypothetical mine environs depicted in Figure 1. The mine is located near the catchment divide and draws its water supply via a gravity line. Tailings from the process plant are piped to a tailings dam on a sub-catchment below the plant site. The objective is to determine the distributions of cyanide species concentrations at a compliance point just upstream of a major settlement to ensure they do not exceed regulatory limits.

Jan 1, 1991

By R. C. Oberth, C. F. Lee, E. M. Taylor

INTRODUCTION Underground siting of nuclear power stations is drawing increasing attention in various parts of the world. Scandinavian countries took the early lead in this field because of their experience in the design and construction of underground hydroelectric stations and industrial plants, and because they have near-surface rock formations which are ideally suited for hosting large underground caverns. The world's first underground nuclear facilities were built in Norway (Halden) and Sweden (Agesta) and were commissioned in 1959 and 1963 respectively. Figure 1 summarizes the main features of these and two other small-scale European facilities. (1-4) American utilities and regulators are also for a variety of reasons assessing the benefits and penalties of underground siting. A recent study by Sandia Laboratories (contracted by the Nuclear Regulatory Commission (NRC) focussed on identifying potential safety benefits of underground siting. (5) Although the study concluded that underground plants would have improved containment for some accidents, as well as better external protection, NRC, in assessing the overall benefits and penalties, decided not to impose mandatory underground siting for nuclear stations. In June 1976, the California Legislature enacted a law which directed the California Energy Commission (CEC) to examine the issues concerned with underground siting of

Jan 1, 1979

By C. A. Fleming, K. W. Sarbutt, P. K. MacPhail

The SART process has been developed for Teck to treat bar­ren solution from the cyanidation/CIP process that has been developed for the Lobo-Marte project in Chile. The objective of the process is to recover cyanide in a form that is suitable for recycling to the leaching part of the process. The Marte and Lobo ore bodies require a dosage rate of about 2 kg/t NaCN, of which only 0.5 kg/t is truly consumed (as thiocyanate, cyanate and ferrocyanide species). The remaining -1.5 kg/t is present as cop­per cyanide (-1 kg/t) and free cyanide (-0.5 kg/t), and is poten­tially recoverable and recyclable. SART is an acronym that describes the unit operations in this cyanide recovery process; namely, .. Sulphidization .. Acidification .. Recycling of precipitate " Thickening of precipitate The basic chemistry has been applied previously, and has also been the subject of two patents (American Cyanamid Company, 1965, Potter et al., 1986). The process involves the conversion of all free and WAD cyanide in solution to hydrocyanic acid by acidification of the tailings solution to pH :s,4, and the conversion of all copper in solution to cuprous sulphide (synthetic chal­cocite) by the addition of a sulphide salt:

Jan 1, 1998

By Caren Caldwell, Leslie Thompson

1.1 Biological Process Description Pintail Systems, Inc. (PSI) has developed and in partnership with their clients in the mining industry has applied biological remediation processes for detoxification of spent ore and process solutions from heap leach operations. Contaminants that are treated to mine closure levels or drinking water standards include cyanides (weak acid dissociable and total cyanides), thiocyanate, nitrates and heavy metals. Biological processes are both site-specific and ore-specific processes. PSI specializes in isolating indigenous microorgan­isms from spent ore and process solutions and augments them in the laboratory for enhanced bio-detoxification in the field. Bioaugmentation in the lab is a key to successful heap bio-detox in the field. In PSI's bioaugmentation processes native microorganisms are isolated from the spent ore environment and are tested for contaminant remediation capacity. A majority of the indigenous microbes will be tolerant of the spent ore environment but will not contribute to contaminant metabolism. Indigenous enrichment or biostimulation of these non-working microbes by adding trace nutrients can competitively inhibit the working microbes. For this reason PSI focuses on the bioaugmentation process where non-working microbes are discarded and the working population is enhanced through stress, mutation and exogenous enrichment before it is re-introduced to the heap and process solutions.

Jan 1, 1997

By A. Giblett, J. Shuttleworth, R. Dunne

In a previous paper (Dunne, Martins, Goulsbra, Chittenden 1997), the new gravity circuits at Telfer Gold Mine, which incor­porate Knelson centrifugal separators in both the sulphide and oxides, are described. The advantages of the new circuits over the replaced spiral ( oxide circuit) and jig (sulphide circuit) were discussed, as were the improvements in gravity gold recovety. It is of note that the installation of the centrifugal separators in themselves did not result in increased gold recovery. The realisa­tion that changes in gold room practices are required to take advan­tage of the increased fine gold recovery from the Knelson concen­trator was an important step towards improved gravity gold recov­ery. This was achieved by increasing the time taken to treat the Knelson concentrate on the shaking table in the gold room. Although this increased gold recove1y, it was found that the table tailings, especially from the sulphide circuit, still contained high values of gold. In an effort to ascertain ways in which gravity gold recovery could be fu1iher improved, a sample of the sulphide table tailings was sent to the Oretest Laboratory in Perth for testwork. The results from this program are discussed in this paper.

Jan 1, 1998