Search Documents

By Ralph T. Buscarello

For practical purposes, the terms "natural frequency," "resonance" and "critical speed" are synonymous. A part passing though its "critical" or "critical speed" may also be said to be "resonant" or "resonating." The vibrations of a precisely balanced part can be magnified by the structure in which it is assembled. Anyone who has driven an automobile knows that it will vibrate more at a certain speed than at others. According to the formula for centrifugal force, vibration should increase steadily with a rise in rpm. What happens instead is that the vibration not only in- creases with r m. but suddenly rises at a much higher rate through the critical speed, and then apparently smooths out as the rpm passes beyond it. To visualize what happens, consider a simple flat spring with a weight mounted at one end. When the spring is deflected by pulling down on the weight and then letting it go, the spring will oscillate, and the spring-and-weight system will vibrate at its natural frequency. If the timing or direction bf the impulses imparted to the spring did not coincide with its natural frequency, the result would be an irregular vibration that would not build up. If, on the other hand, the timing and direction of the impulses did coincide with the spring's natural frequency, the result would be a larger and larger amplitude. If the impulses were continued indefinitely, the amplitude of the spring's vibrations would go on rising [while its frequency stayed the same] until the spring broke or the amplitude of the vibrations reached an equilibrium [because frictional or other forces would tend to damp it]. Resonance magnifies the amplitude of vibrations in a relatively undamped system between 100 to 200 times over that of nonresonant vibrations. Frictional or viscous damping often reduces the magnification [from 10 to 20 times], but even with this reduction the amplitude would still be large enough to cause excessive wear, and sometimes even fractures. For example, a blower might show only 0.001 in. of vibration on the manufacturer's test stand. Installed, the blower could pass into its critical speed [the speed at which the frequency of the vibrations caused by the rotor coincides with the supporting structure's natural frequency], and the 0.001 in. of vibration could be resonated to 0.010 in., or as much as 0.020 in. The cure for such a condition would not be to lower the vibration of the blower by further balancing or better alignment but to separate the two frequencies by at least 20 to 30%.

Jan 1, 1970

By M. P. Meehan

The purpose of this paper is to present the Anamax Instrumentation Department's: responsibilities, organization, preventive maintenance, test facilities, training and applications. The Anamax Mining Company is a general partnership between AMAX Arizona, Inc. (a subsidiary of AMAX INC.) and The Anaconda Company (a subsidiary of Atlantic Richfield). Anamax's product and by-products include: copper, molybdenum, and silver; uranium is to be added as a by-product in early 1980.

Jan 1, 1980

By R. L. Garrett

The quality of mineral additives used 1n a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally used minerals are bentonite, barite, barite/hematite blends and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity, gel strength and to provide a low permeability filter cake. A multi-million dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason why oil companies who use these materials sometimes set their own quality standards beyond those already specified in API Spec. 13A. Also discussed in this paper are the current standardization activities in API Committee 13 on these minerals.

Jan 1, 1986

By G. Kraemer, J. A. Le Gac, P. R. ZETTWOOG

I. INTRODUCTION During the course of our activities in assisting mining companies, we have had access to the monitoring results for personnel from a large number of uranium mines. The results differ greatly from one mine to another. One of our objectives has been to discover the origin of these differences. It is evident that they are largely due to variations in the geological context, to mining methods, and to the organization of the work ; but we also found that the rigor with which measures are implemented to prevent the personnel from being exposed to radiations is also a cause. In order to advise mining operators effectively, we have asked ourselves the following question Given the dosimetric results of a mining site, how can it be known - if occupational exposure has been reduced to the lowest possible level (dose optimization principle recommended by the ICRP) ; - if the exposures were justified, which would not necessarily be the case following a questionable choice of the mining method, for instance, or a lack of efficiency in the maintenance and repairs of ventilation apparatus or even an excess of radiation protection. It is necessary to establish some criteria, while taking into consideration the specific conditions for each mine, in order to determine whether a mining company is adequately implementing radiation protection procedures. This need led us to attempt a modelization of the occupational exposures of uranium miners ; the preliminary phase is presented here. Although voluntarily still very basic, this model makes it possible to demonstrate the role of certain dynamic or passive variables. Moreover, the model presents the concept of specific irradiation of a mining site equal to the collective dose received per ton of uranium metal supplied to the uranium mill. The specific irradiation can therefore be used to indicate the effectiveness of radiation protection procedures at a given mining site. This model can be used for - previsional exposure studies based on the use of data gathered at each site, making it possible to compare various work methods and to determine prevention means ; - qualification of "radiation protection" procedures at a mining site ; - detection of unjustified exposures ; - research of ways to reduce inevitable exposures. 2. DETRIMENT TO BE ASSOCIATED WITH A GIVEN EXPOSURE DISTRIBUTION Respecting exposure limits ensures that delayed stochastic effects are the only health risks to workers. If the hypothesis of linearity in the dose-effect relationship is applied, the detriment to a group of workers is proportional to the sum of exposure for all the workers, or the collective exposure usually expressed as man x rem. On this point the linearity of effects hypothesis makes it possible to consider that two different standard deviation distributions having the same mean value are equivalent. It would be possible, then, to reduce the standard deviation by changing the distribution of workers at the various working places without changing the mean exposure value. In other words, without taking into consideration the practical implications, individual limits can be respected by rotating the personnel or by reducing the individual working period which would be compensated by increasing the number of workers. The collective dose would remain the same, which would justify the use of the concept of collective exposure. 3. "RADIATION PROTECTION" QUALITY INDEX AT VARIOUS MINING SITES Each mining site is responsible for its own collective dose, but it is also responsible for producing a certain amount of uranium metal in the ore sent to the uranium mill. These two quantities must be brought together in order to establish the "radiation protection" quality index of a mining site. This quality index, called-specific irradiation (Ir) is expressed in rem.ton -1 for external irradiation, in mJoule.ton-1 for inhaled [a]-energy, and in Ci.ton -1 for inhaled radon *. The specific irradiation represents the health hazard which must be associated to the extraction of one ton of uranium metal. Figures la and lb present a system of coordinates for which the axis of the abscisses is graduated in tons of U metal and the axis of the ordinates is graduated in units of collective exposures. In the EEC, the regulation is based on the measurement of the amounts of radon 222 inhaled.

Jan 1, 1981

By J. G. Groppo

A beneficiation process has been developed to provide selective separation of unburned carbon from high LOI fly ash. Previous reports of utilizing froth flotation to achieve selective separations required long residence times and high reagent costs. A proprietary reagent system has been developed to address both of these limitations. Based on the results obtained from laboratory and pilot-scale investigations, a flowsheet design has been developed to produce two distinct usable products from class F fly ash; low LOI ash and a high carbon product suitable for reburning or further upgrading. A process flowsheet and description are presented.

Jan 1, 1996

By Robert T. Chapman

Many of us are privileged in that we have witnessed the transition from mining methods used in the first quarter of the twentieth' century to those practiced today. In the late Twenties, for example, many mines still used hand mucking methods. In the middle Thirties, more than one large metallurgical limestone quarry still used the 4 cubic yard railway steam shovel formerly in use at the Panama Canal. Mules could occasionally still be found underground, where they provided the-main-source of motive power. Within the last decade, and even within the past five years or less, great improvements have been made in blast-hole drilling, ore loading, and ore hauling equipment. Industrial demand for minerals can be expressed in exponential terms as compared to that at the turn of the century. Even marine mineral resources are receiving accelerated attention. One overall result is that larger and lower grade orebodies can be exploited at a profit. This profit must be made despite, for example, a static monetary price for gold, and despite the continual cost escalation involving labor, materials, supplies, and equipment. Accordingly, the application of the necessary degree of knowledge and judgment required to meet production, cost, and profit goals is paramount.

Jan 1, 1966

By N. B. Aughenbaugh

Subsidence due to abandoned coal mines has received copious attention recently. This is a result of many factors such as the enactment of new mining laws and the effect subsidence has on land use over the mines. Prediction of subsidence features and the time aspects over supercritical extraction (i.e., longwall and high extraction ratio pillaring) is relatively accurate. However, predicting when subsidence will occur and the surface features' size and shape above subcritical extraction of room and pillar mining is not yet possible. This paper will discuss the factors that influence the time aspects of subsidence in room and pillar mining.

Jan 1, 1983

By P. Rusin

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environ-mentally unacceptable. Bio-reductive leaching of such ore samples at MBX resulted in high recoveries of silver and molybdenum. When baseline 3-day cyanide bottle roll tests were conducted on manganiferous oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bio-reduction with 99.8% dissolution of manganese. A follow-up cyanide bottle roll test yielded an additional 8.5% silver recovery for a total recovery of 94.5%. Baseline 3-day acid bottle roll tests of the iron oxide molybdenum ore yielded 1.8% moly. However, bio-reduction solubilized 93.3% of the moly into the growth medium. An additional 0.3% moly was recovered during the follow-up acid bottle roll test. Microbial treatment of refractory oxide ores with bio-reductive bacteria resulted in higher recoveries of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and moly was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1992

By Stephen L. Chryssoulis

The detection and quantification of invisible gold by microbeam techniques is discussed. Ion probe microanalysis is used to quantify the gold content of individual sulphide, sulpharsenide and oxide particles with a detection limit of 0.2 ppmw (g/t). The proton microprobe is used to determine the gold concentration of gangue minerals with a detection limit of 2 - 4 ppm. Using these techniques complete mineralogical balances for gold are obtained to assist in the process selection and optimization. A total of twenty gold and gold-bearing ores have been examined. Selected examples are presented.

Jan 1, 1990

By George A. Komadina

The Pima Mining Company lies 20 miles southwest of Tucson, Arizona, and some 45 miles north of the Mexican border. The mill is situated on a hillside overlooking Tucson and the Santa Cruz Valley, the ground generally sloping northeast at a 2.5 percent grade. The hillside location allows for gravity flow generally through the plant as well as for: tailing disposal.

Jan 1, 1965

By D. H. Stonehouse

There is no such thing as an industrial minerals industry. There are, however, many industries operating in the general field of industrial minerals. And although we use the phrase "industrial minerals industry" out of sheer convenience, the only common denominator among, say, the potash mining and processing industry, the sulphur-sulphuric acid industry and the granite industry is, in fact, that they each are exploiting an industrial mineral resource. May I quote the person whom I consider to be the reigning Mr. Industrial Minerals, Robert L. Bates, who in the 4th edition, 1975, of Industrial Minerals and Rocks states: "An industry is considered to belong to the industrial minerals field if its operations consist of extraction and processing, but not manufacturing. Thus the mining and beneficiation of feldspar is a mineral industry, but the manufacture of ceramic products is not. In the cement and lime industries, processing merges into manufacture, and the line is less distinct. It disappears altogether in a plant that extracts salt as artificial brines, and makes sodium and chlorine chemicals, all under the same roof."

Jan 1, 1981

By Paul K. Sims

The Central City district is one of several adjacent mining areas in the Front Range, Colorado, that contain precious metal-bearing sulfide veins of Laramide (Late Cretaceous and early Tertiary) age. The districts are in the Front Range segment of the Colorado mineral belt, and are characterized by porphyritic igneous rocks of intermediate composition that have intruded Precambrian crystalline rocks in the core of the Front Range. The veins and minor stockworks that constitute the ore deposits in the district were formed largely as fracture fillings. The veins range from simple fissures to complex, branching lodes, and commonly range from less than 0.5 to about 1 m in width. The principal values are in gold and silver. The common metallic minerals are pyrite, sphalerite, chalcopyrite, tennantite, and galena; minor minerals are enargite, pitchblende, and gold tellurides. Quartz, cryptocrystalline silica, carbonates, fluorite, and barite compose the gangue. The ore deposits have a well-defined concentric zonal arrangement. A core of pyrite veins (central zone) is surrounded by a peripheral zone of galena-sphalerite vein with gold and silver. An intermediate zone contains transitional veins that have minerals characteristic of both the central and peripheral zones. The minerals were deposited in three stages during a single period of mineralization: uranium; pyrite; base metals, gold and silver. The wall rocks were altered primarily during pyrite-stage mineralization. Sericite envelopes developed adjacent to fractures, and were succeeded outward by zones of argillized rock. The valuable ore minerals were deposited in ore shoots localized by several types of structural controls, principally vein intersections, the physical nature and structure of the wall rocks, and irregularities along the fractures themselves. During supergene alteration, gold was concentrated in the upper, oxidized parts of the veins, commonly to depths of 50 m. The precious metal-bearing sulfide ore deposits are closely associated in space and time with the Laramide porphyritic igneous rocks and are believed to have been derived from hydrothermal fluids related to the magmatic activity. The ore deposits have mesothermal aspects and apparently formed in the temperature range 200°-320°C.

Jan 1, 2013

By Enrique Llewellyn

North River Energy Company a previous subsidiary of Republic Steel Corporation commenced development of the Number One Mine in mid-1972. The mine is located in West Alabama and presently employs a total of 632 people. Production capabilities have increased to 1.4 million clean tons of steam coal per year with the newly purchased Longwall System. Washer recovery averages 57 percent. The seam being mined is the Pratt or Corona with an average height of 52 inches and an average cover of 540 feet. The immediate roof is laminated sandstone and the floor is composed of a hard fireclay. Total production out of the mine is provided to Alabama Power Company under a longtime contract.

Jan 1, 1981

By J. W. Mustard

The Macmillan Pass tungsten property (MacTung) is the largest known copper-tungsten, calcic, exoskarn deposit in the Western Hemisphere. Located on the border between the Yukon and Northwest Territories in northwestern Canada, the deposit crops out on Mt. Allen within the Selwyn Mountain Range. It was discovered in 1962 by a subsidiary of AMAX Inc. and has since been explored by 16,300 meters of surface and underground diamond drilling and by 800 meters of underground development. Geologic reserves are in excess of 30 million tons, grading slightly less than 1.0% WO3. Scheelite (CaWO3 ) is the main mineral of economic interest. Accessible by road, the property is not in production. Previously estimated reserves at MacTung have been unable to fully utilize all the geological controls on mineralization. In the past three years, however, an intensive program has been underway to improve our understanding of the deposit and to use the resulting information in a more precise way. This paper will discuss the key aspects of the geology as they specifically relate to reserve estimation and will demonstrate how these controls are being used in a geostatistical model of the deposit.

Jan 1, 1985

By Ayman A. El‑Midany, Hassan E. El‑Shall, Kerri‑Ann A. Hue

Modification of clays is necessary for the zearalenone (ZEN), as long-chain mycotoxins, removal. The organic-cations were usually used to modify the clay hydrophobicity to accommodate the large mycotoxin molecules. In this study, tri capryl methylammonium (TCMA) chloride and common corn oil were used in clay modification. Several characterization techniques such as XRD, FTIR, and TGA were used to identify the d-spacing changes after modification either by TCMA or corn oil. The results of applying the TCMA-corn oil-modified clays in ZEN removal indicated a noticeable improvement where more than 90% of ZEN could be removed in vitro at acidic and neutral pH values. The success of eliminating a high percentage of ZEN molecules is due to the expansion of intergallery spacing as a result of TCMA surfactant intercalation within the clayforming layers. The removal percentage does not depend only on pH but also on the amount of clay used. In addition, the ZEN removal in the presence of corn oil is better at acidic pH and small clay amount where the ZEN can be fully removed.

Sep 27, 2021

By Fred L. Myers

The use of finite element programs for evaluating large grinding mill shells is becoming increasingly popular. However, large scale, detailed analysis can become a burdensome task when one is required to manually prepare the necessary data to be entered into the program, while evaluating the voluminous results is even more devastating. Although available computerized finite element analyses can reduce computation time from years to months or even weeks, additional pre and post processors can reduce the time for data preparation and result evaluation to hours, while simultaneously reducing the probability of human error. Examples of the uses of these processors are presented as well as typical modeling techniques.

Jan 1, 1979

By E. C. Winegartner

In producing and selling coal, the coal company is faced with many different parameters by which the quality of its product is evaluated. One type, which we choose to call the economic parameters, includes moisture, ash, sulfur, and Btu's. These are reasonably well understood by both the coal supplier and the customer, and the dollar values can be placed on them. This is the group of parameters of primary interest to most purchasing agents buying coal. A second group of parameters governs how the coal will behave in the boiler itself and is of primary concern to the engineers designing the boiler and to the men who must operate and maintain it. Since we have not yet learned to put dollar values on these parameters, they generally show up in coal contracts simply as cutoff points, the purchaser simply saying that he will not accept coal outside of certain limits.

Jan 1, 1975

By Peter I. Brooker

The semi-variogram, the basic tool of geostatistical estimation procedures, must itself be estimated from the available data. From a numerically simulated two dimensional deposit, with known variability expressed through its semi-variogram, the standard arithmetic mean estimator is used to calculate experimental semi-variograms. These are determined on a series of data sets obtained from the deposit with various sampling grids which cover different areas of the deposit and which have a wide range of available data. The orders of discrepancies between estimated and theoretical semi-variograms are determined in this idealized situation; and this provides a basis against which to assess experimental semi- variograms made on field data.

Jan 1, 1982

By Paul Madsen, Bade Sozer, Thomas Hennings, Eileen Test

The Rondout Bypass Tunnel in New York has two access shafts. The upper sections of the shafts are lined with steel pipe to resist a substantial net internal water head . Initial design included a ¾-inch-thick cement mortar lining (CML) for all three components. Because of concerns with CML application on large-diameter pipes, the protective lining was redesigned for shotcrete application. This paper discusses the details of that design, mock-ups, and shotcrete application.

Jun 13, 2023

By P. A. Korpi

In March of 1978 the first set of Angular Spiral Liners utilized in grate discharge ball mills for wet grinding was put into service in the San Flanuel Concentrator of Flagma Copper Company. The use of these liners has decreased grinding media consumption by 19.2% and grinding energy consumption by 15.8%. In addition a 1.1% increase in grinding throughput is being realized through the use of the system. This paper describes the Angular Spiral Lining System and reviews the test program at the San Manuel Arizona Concentrator. Operating parameters are discussed in addition to the current testing program to futher optimize the system.

Jan 1, 1982