Search Documents

One of the major objectives of cost analysis is to enable the manager to predict the financial outcomes of decisions. To accomplish this, the future costs and benefits of alternative courses of action must be determined. If care- fully used, information about past financial performance can be helpful in this analysis despite the fact that, by definition, financial reporting information is historical. In many cases, both revenues and costs need to be estimated for decision- making. For the production manager, additional revenue is a result of increased throughput or recovery of valuable material from the stream of mined material. A reduction in operating cost, although similar to a revenue increase in its financial impact, is estimated using slightly different techniques. Generally, the estimation of cost is more difficult than the estimation of revenue. Most cost estimates have two components: an estimate of fixed costs and an estimate of variable costs. As discussed in chapter 5, the total cost of an activity during a specified period can be expressed as: Total cost = (Variable cost per unit of activity) x (Units of activity) + Fixed cost or TC = VX+F

Jan 1, 1999

The processing capability of a semi-autogenous (SAG) mill is greatly affected by ore geology and operating variables within the mill. The SAG mill is problematic because it cannot be conveniently studied on a smaller, laboratory-scale mill. The interior of the mill, where grinding takes place, cannot be observed using instrumentation available today. Yet the motion of the rock and ball charge determines the power draft and hence capacity of the mill. Therefore, mill optimization is pursued with a charge motion simulation software. This software uses the discrete element method to describe the individual motion of numerous ball and rock particles in the mill. It is shown that by simply increasing the chord length between the lifters and increasing the face angle of the lifters the capacity of the mill can be increased. Such a configuration of lifters allows the operator to increase mill speed, hence drawing higher power while considerably minimizing direct ball strikes against shell plates and lifters. A case study of a 36 ft. diameter x 15 ft. long mill is presented. Reducing the direct ball strikes leads to lesser steel consumption both in terms of balls and lifters.

Jan 1, 2000

By Babcock. C. O.

This report presents equations derived from experimental testing to convert borehole pressure cell data from vertical and horizontal cells to the biaxial ground stress changes. While hydraulic pressure cells in boreholes have been in extensive use since 1957, methods of data reduction have been slow to develop. The methods of Sellers (1970) and Bauer et al. (1985), respectively, indicate a linear relationship between cell pressure change and the rock stress change. Lu presented a theory for creep behavior (Babcock et al., 1982). In the present work, in laboratory testing, the logarithm of the cell pressure was related to the stress change in seven elastic materials for a range of Young's moduli of 3.45 to 85.5 GPa (0.5 to 12.4 x 106 psi). The gage response depends upon the setting pressure of the gage, the gage pressure at any time, the rock properties, and the cross-sensitivity of the gage to transverse loading. The setting pressure of the cell should be proportional to the Young's modulus of the rock, the absolute stress can be determined by overcoring in strong rock, and the in situ Poisson's ratio can be estimated in some cases from the cell responses.

Jan 1, 1986

By Michael G. Nelson

In 1992, the Alaska Department of Environmental Conservation received a grant from the Environmental Protection Agency (EPA) to fund the reclamation of an abandoned placer mine. The project also included the development of a water-quality and hydrologic-monitoring program. The grant was provided under Section 319 of the Clean Water Act and is administered through EPA's Region X Water Division. For the past 100 years, Alaska's interior has been the site of extensive placer-mining operations. Early surface and underground operations left small tailings piles, some of which are still visible. Dredging left larger tailings piles, similar to those in California and elsewhere. The only reclamation of these tailings involved use as road base and fill and other civil applications. Most active mines in Alaska are on state and federal lands. The standards of reclamation for mines on federal lands are established under US Mining Laws, 43 CFR 3809. They address only mines operated since 1981. Under a state statute passed in 1990, the Alaska Department of Natural Resources, Division of Water and Mining, has issued reclamation regulations. These regulations apply to sites on state, federal and private lands, but only those mined since Oct. 15, 1991.

Jan 1, 1995

By John A. DesLauriers

INTRODUCTION This paper will update the status of small sized tunnel boring machines used in both the Mining and Civil Industries. I will mention a) new developments in small size hard ground tunnel boring machines, b) review North American performance records of the Atlas Copco Mini/Midi Fullfacers, and c) compare relative costs in driving a 1200m (4000 ft) typical utility tunnel using a leased TBM versus the conventional drill and blast method. NEW DEVELOPMENTS JARVA MACHINES Of all small rock tunnel boring machines currently in use, the Jarva MARK VI and MARK VIII are receiving the most enthusiastic acceptance. These circular fullface borers using usually 15 inch single disc cutters (manufactured also by Jarva) are designed on the 'T' bracing principle. Previously, Jarva's line of tunnel boring machines, even their smallest, was designed on the 'X' or double diagonal bracing configuration with a gripper in each quadrant. In small tunnels where net room is so very important, the 'T' scheme with gripping only at the spring line nets precious room around the cutter unit for passage of men and supplies. It allows freer un-

Jan 1, 1981

By E. C. H. Becker

When data points, plotted on X-Y coordinates, lie along a simple line, their regression can be matched to a high degree of accuracy by one or other simple algebraic expression (Boot and Cox, 1970). Under these conditions, interpolation is axiomic. Further, if the expression defines no more than a straight line, a parabola or other such line which can be related to some specific mechanism which generates the points, then extrapolation might be valid. However, any extrapolation would depend on the continued, unchanged functioning of the mechanism. Studies of more intricate assemblages of data points have long been based on representation by means of series (Fourier, 1811). If sufficiently complicated, several different algebraic expressions can represent the same intricate regression accurately (Hoerl, 1954). However, without reference to a mechanism, no extrapolation is contemplated. Typically, variations in the prices of minerals with time are. sufficiently complicated to render invalid any simple attempts at extrapolation. The computer, however, can be used to derive algebraic expressions which match complicated regressions and also can be represented by the functioning of a mechanism (Becker, 1984). The techniques involved have been applied with advantage in the study of time series representations of mineral prices.

Jan 1, 1986

By V. A. Evans

The preparation of a paper reporting fluorspar economics in the United States at one point in time could have been somewhat complicated be- cause of the number of producers, both large and small, that derived production from different locations throughout the Western U. S. and the Southern Illinois and Western Kentucky fluorspar districts . Companies such as Allied Chemical and William- son Mining operated in the Jamestown district of Colorado. In Walden and Salida, Colorado, the Colorado Fluorspar Company operated mines and mills.

Jan 1, 1986

By G. T. Lineberry, R. S. Mateer

Often only after years of "technical dormancy" do errors in published literature become apparent and meaningful. To prevent duplication of effort for future generations, the fol¬lowing corrections are offered. These errors were discovered during a recent study in which a computer program for mine hoist rope selection was developed (Lineberry and Mateer, 1988). In order of increasing gravity: Captions for Figs. 3 and 4 are transposed. • Purported to be a more accurate method of rope selection than the process of successive approximation, the direct method assumes linearity between a given rope's minimum breaking strength, T, and unit rope weight, Wv. Because of the sensitive location of the constant, K, in equation (8) for breaking strength, the significance of this nonlinearity is magnified. For a typical 6 x 37 class fiber core wire rope (Wire Rope Corp. of America, 1985), K actually varies from 43,650 to 52,190, depending upon rope diameter. Although the direct solution permits a rapid selection of hoist rope, an indirect (iterative) solution procedure is favored because of its im¬proved accuracy and ease of computerization. • Equation (8) for minimum breaking strength is in error. It should read:

Jan 1, 1989

By G. T. Lineberry, R. S. Mateer

Often only after years of "technical dormancy" do errors in published literature become apparent and meaningful. To prevent duplication of effort for future generations, the following corrections are offered. These errors were discovered during a recent study in which a computer program for mine hoist rope selection was developed (Lineberry and Mateer, 1988). In order of increasing gravity: Captions for Figs. 3 and 4 are transposed. Purported to be a more accurate method of rope selection than the process of successive approximation, the direct method assumes linearity between a given rope's minimum breaking strength, T, and unit rope weight, WV. Because of the sensitive location of the constant, K, in equation (8) for breaking strength, the significance of this nonlinearity is magnified. For a typical 6 x 37 class fiber core wire rope (Wire Rope Corp. of America, 1985), K actually varies from 43,650 to 52,190, depending upon rope diameter. Although the direct solution permits a rapid selection of hoist rope, an indirect (iterative) solution procedure is favored because of its improved accuracy and ease of computerization. Equation (8) for minimum breaking strength is in error. It should read:

Jan 1, 1990

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Increasing demand for high-grade manganese (Mn) ore has led to the practice of selective mining, which produced low-grade Mn ore as waste and in the long term could lead to environmental pollution. Research had been carried out to extract Mn from low-grade ore, which mostly exists as black Mn(IV) oxide (MnO2). Most extraction methods involved the reduction of insoluble MnO2 to soluble Mn2+ in acidic media. Metals other than Mn are also transferred to the pregnant leach solution (PLS) during the leaching process, especially iron (Fe). Due to high Mn concentration in PLS, precipitation is considered the best method to isolate Mn from PLS compared with solvent extraction and ion exchange/absorption. However, due to unselective leaching, the presence of Fe in the PLS makes the Mn separation and purification difficult. Therefore, in this research, the parameters affecting the selectivity of Mn over Fe in leaching process were investigated.

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The U.S. National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau of Mines (USBM) have put significant effort over the past four decades into researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers who perform the manual bagging and palletizing of 50- to 100-lb bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper provides an overview of available dust control technologies for bagging operations and presents the findings of a recent case study conducted at four industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation is also performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

By Elif Emil-Kaya

Samarium (Sm), as one of the rare earth elements (REEs), has gained significant attention in the production of samarium- cobalt (SmCo) magnets due to their high corrosion and oxidation resistance, as well as their high-temperature stability. SmCo magnets find applications in various industries, including but not limited to national defense, aerospace, military and medical equipment. Sm and Co have been classified as critical metals due to their economic importance and supply risk. Recovering Sm from SmCo magnets is an effective method to ensure a stable supply. The present study investigates an integrated hydrometallurgical treatment and combustion process for the preparation of rare earth oxide (Sm2O3 ) powders from SmCo. Initially, SmCo powders are exposed to nitric acid, and the resulting slurry is selectively oxidized at 250 °C to obtain Sm(NO3)3 , Co2O3 and Fe2O3 . Subsequently, the selectively oxidized powders are leached with water to extract Sm. Sm2O3 powders are produced from the obtained leaching solution using an energy- and time-efficient solution combustion process. Finally, the optimal conditions for the production of Sm2O3 are identified, and the produced powder is characterized through X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) analysis.

Nov 1, 2024

By Eileen Ashworth

Computer-assisted instruct ion is now being used in areas as diversified as training handicapped children to preflight simulation for airline pilots. This paper reports on two courses that have been developed at SDSM&T on the PLATO system for miner safety training. Advantages of computer-assisted instruct ion for this type of training is discussed. (Figures show examples of actual use.) A discussion will be given on other applications such as maintenance troubleshooting, training of engineers and managers at remote sites and training of local people for working in the mine.

Jan 1, 1983

By Paul L. Russell

U. S. petroleum demand has increased at a rate greater than that of domestic production. A domestic energy source that is under serious consideration to augment present supply is oil shale. The Green River formation in Colorado, Utah, and Wyoming represents a resource potential containing about 2 trillion bbls. of oil in shales averaging 15 gallons or more per ton or more than 400 billion bbls. in 30 gallon per ton shales. This paper will consider the technological and environmental aspects of developing this resource.

Jan 1, 1974

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

With the rise in global demand for pure copper, there is an urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as effective and efficient leachants for the dissolution of chalcopyrite. This work reports on different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from the Wase local government area of Plateau state, Nigeria, and assayed as 11.30 weight percent copper.

May 1, 2023

By S. A. Anzalone

The Helvetia copper deposit is a large undeveloped Laramide porphyry copper system located in the Santa Rita Mountains, Pima County, Arizona. This porphyry copper system consists of four areas of copper mineralization: Rosemont, Peach-Elgin, Broadtop Butte, and Copper World. Asarco refers to the four areas collectively as the "Helvetia Deposit". Mineralization and alteration are primarily contact pyrometasomatic, and zoning of hydrothermal alteration and sulfide mineral assemblages are similar to those observed at the Twin Buttes and Mission copper mines located approximately 32 km west of Helvetia. Asarco acquired the Helvetia Deposit in 1988 and has continued the exploration and development effort since then. A considerable amount of excellent geological work has been completed in the area but little information has been published on developments since the mid-1950's. The geology of the deposit as developed by numerous geologists over the past 75 years and the large, bulk tonnage low grade copper deposits outlined in recent years will be briefly reviewed in this paper.

Jan 1, 1992

By R. E. Lund

The design, operation, and performance of an integrated pilot plant for recovering zinc and copper from a complex sulfide ore are described. Metallurgical processing comprised selective sulfate roasting in a fluid bed, leaching in a weak sulfuring acid solution, recovering copper by cementation with scrap iron, air oxidation to remove soluble iron, more-or-less conventional purification for removal of impurities deleterious to zinc electrolysis, recovering zinc by electrolyzing solutions, and recycling spent electrolyte to the sulfating roaster. The effects of several feed preparation and roasting variables on the sulfation response of zinc, copper, and iron are set forth, together with the electrolyzing characteristics of the zinc solutions.

Jan 1, 1962

In this paper, we present design and implementation details of a fuzzy-behavior-based controller for an automated excavator. This robotic excavator must be equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered from bucket mounted force sensors during the excavation process. Implementation details and experimental results using the fuzzy behavior based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining excavator controller.

Jan 1, 1996

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Significant strides have been made in optimizing the design of filtration and pressurization systems used on the enclosed cabs of mobile mining equipment to reduce respirable dust and provide the best air quality to the equipment operators. Considering all of the advances made in this area, one aspect that still needed to be evaluated was a comparison of the efficiencies of the different filters used in these systems. As high-efficiency particulate arrestance (HEPA) filters provide the highest filtering efficiency, the general assumption would be that they would also provide the greatest level of protection to workers. Researchers for the U.S. National Institute for Occupational Safety and Health (NIOSH) speculated, based upon a previous laboratory study, that filters with minimum efficiency reporting value, or MERV rating, of 16 may be a more appropriate choice than HEPA filters in most cases for the mining industry. A study was therefore performed comparing HEPA and MERV 16 filters on two kinds of underground limestone mining equipment, a roof bolter and a face drill, to evaluate this theory. Testing showed that, at the 95-percent confidence level, there was no statistical difference between the efficiencies of the two types of filters on the two kinds of mining equipment. As the MERV 16 filters were less restrictive, provided greater airflow and cab pressurization, cost less and required less-frequent replacement than the HEPA filters, the MERV 16 filters were concluded to be the optimal choice for both the roof bolter and the face drill in this comparative analysis case study. Another key finding of this study is the substantial improvement in the effectiveness of filtration and pressurization systems when using a final filter design.

Aug 1, 2016

By S. D. Thompson

Since 1965 several researchers have independently developed computer models for designing gathering belt and surge bin capacities in underground coal mine belt systems. Table 1 summarizes the models applicable to U.S. mining systems. Most of the models, employ the Monte Carlo simulation technique. Basically, the belt loading at each loading point is randomly produced from probability distributions. In some cases, a combination of deterministic calculations and probability distributions are used to simulate the loading. Once the loading is simulated, it is systematically moved through the belt system in a deterministic fashion based on belt speeds, belt lengths, and storage bin discharge rates. The coal flowing from each loading point is tracked as it moves through the belt system. When the loading from tm different sources combines on a belt or in a surge bin, checks are made to determine if capacities have been exceeded. If capacities have been exceeded the amount of spillage is calculated. At the end of the simulated time period, the cumulative spill- age is used to evaluate the belt and surge bin capacities. Naturally, a considerable amount of spillage indicates the capacities are unacceptable. Acceptable capacities are generally indicated by minimal spillage. Numerous trial simulations are often necessary to find the acceptable capacities.

Jan 1, 1987