Search Documents

By K. Severin, B. Flanigan, P. Marion

"Plutonic-related" gold deposits in Interior and SW Alaska (Tintina Gold Belt) vary significantly in size, grade, vein/deposit morphology, depth of emplacement, distance from causative pluton and metal association. Metal associations such as Au-Bi and Au-As- (Sb-Hg) are a good empirical indicator of the depth of emplacement and distance from causative pluton. These associations have been used successfully in exploration. Results from several analytical techniques also suggest a phenomenological cause for these metal associations. Gold and bismuth have paired mineralogy at high temperatures and, thus, are best correlated at deposits that are deep and/or close to causative intrusions.

Jan 1, 2003

By S. R. Maynard

The Ortiz Mountains lie 25 mi (40 km) northeast of Albuquerque, New Mexico in Santa Fe County (Figure 1). Approximately 350,000 ounces (11,000 kgs) of gold have been produced from the Ortiz Mountains since the 1820s. The 100 square mile (260 square km) Ortiz Mine Grant was secured from the Mexican government in 1833 by Jose Francisco Ortiz for the purpose of mining gold. The Grant has remained more or less intact to the present. The mineral rights are currently owned by Ortiz Mines, Inc. of Joplin, Missouri and are leased to LAC Minerals, USA, Inc. (west half) and to Gold Fields Mining Corporation (east half).

Jan 1, 1989

By James A. Finch

The Gaudin lecture is devoted to fundamentals. Given my involvement with column flotation over the last 20 years, this is my topic. I have tried to identify spinoff basic research and provide a personal list of favorites. Two are selected for discussion here. They are single bubble rise and bubble surface area flux. The rationale for such work, as well as some of the findings, are reviewed. Support for fundamental work seems as volatile as the economy (and the link is probably not coincidental). I hope some utility to the minerals industry is evident in the text. Column flotation in its current form originated in the early 1960s. The method was invented by Boutin, patented by Boutin and Tremblay and pursued doggedly by Wheeler. Their aim was to overcome the problem of mechanical entrainment of fine particles in the water carried by the bubbles, which they were convinced contributed to lowering flotation concentrate grades (Wheeler, 1988; Finch and Dobby, 1990). The solution was a combination of columnar geometry, the addition of wash water into a deep froth and the maintenance of an excess of water to the tailings, as compared to the feed (a so-called positive bias). Success at Les Mines Gaspe, Quebec, on cleaning Mo in the early 1980s signaled the start of industrial acceptance, making the column one of the flotation machines of choice today. Over the next 20 years, column applications mushroomed to cover virtually all mineral commodities, as well as nonmineral applications such as soil decontamination, deoiling of water and deinking of recycled paper. In the wake, research groups are continuing to probe the fundamentals, conferences and workshops have been transferring the technology and specialist companies have emerged to service the demand. Innovations were triggered as problems arose (for instance, in gas injection systems) and novel flotation cells, much in vogue in the 1990s, had the door opened. Mechanical cell manufacturers have not been idle - there is nothing like competition to provoke a fresh look at an established business. Flotation-cell technology has probably not seen so much activity since the patent rush in the early days of flotation, which occurred around the turn of the century. For an industry often considered reluctant to risk innovation, this is not a bad record. A good idea will find a place, but patience (not always an innovators strong suit) and careful preparation are required. Two books (Finch and Dobby, 1990; Rubenstein, 1996), three symposia (Sastry, 1988; Agar and Huls, 1991; Gomez and Finch, 1996), and a series of reviews (Dobby and Finch, 1991; Finch and Dobby, 1991; Finch, 1995; Finch et al., 1995) document the period. Like many good ideas, column flotation has been overexposed, and there have been disappointments. In a recent example, columns performing scavenging duty were replaced by mechanical cells (Chong et al., 1998). The further applications stray from the original - to

Jan 1, 1999

By Mark J. Logsdon, Barbara Basse

Mississippi Valley Type Pb-Zn deposits are widespread in the midcontinent U.S. and have been mined from the 1800's to present. Some tens of thousands of acres of mined land in the Tri-State District have been designated as Superfund sites as a result of surficial mine wastes and ground waters with elevated levels of metals. EPA considers the surficial mine wastes to be hazardous and a major source of acid mine drainage fAMD) that degrades water resources and threatens human health and the environment. To mitigate potential risks at one site near Galena, Kansas, a group of mining companies who had been identified by EPA as Potentially Responsible Parties IPRPs) proposed subgrade disposal of the mining wastes in shafts and subsidence features. However, this proposal was challenged by the Agency on grounds related to AMD and the potential for degradation of ground water quality. The PRP team developed a program of materials characterization, laboratory-scale leaching, and finally large-scale, pilot testing in the field. Static and dynamic leaching tests at both laboratory scale fusing artificial rainwater under both variably and fully saturated conditions) and field scale (using pH 4.5 ground water) showed that the surficial wastes do not produce acidic leachate and are not a long-term source of metals. Laboratory chemical and mineralogical tests show that the mine wastes contain substantial carbonate, but very limited iron sulfides, consistent with the leach test results. EPA "characterization" tests fEP Toxicity and TCLP) compare very poorly with tests simulating the expected leaching conditions. While these tests would classify the surficia1 wastes as "hazardous, they do not characterize the behavior of the high-volume, low-concentration, coarse-grained materials with respect to environments and disposal options of interest. To be meaningful, characterization of mining wastes must be performed in a manner that simulates the environmental conditions that are actually of interest with respect to a specific decision, such as subgrade disposal in the saturated zone.

Jan 1, 1991

By Natarajan K. A.

During sulphide ore grinding, electrochemical interactions between grinding medium and the minerals play a significant role in bringing out enhanced ball wear on the one hand and alter the surface property of the ground minerals on the other. The role of the flotation reagents added simultaneously during grinding with respect to ball wear as well as flotation is yet to be established. Electrochemical measurements such as rest potential, combination potential and galvanic current between sulphide mineral and ball material couples have been carried out in the presence and absence of flotation reagents to understand the nature of electrochemical interactions between ball material and sulphide mineral. Electrochemical mechanisms and models have been proposed to explain the role played by the flotation reagents during different binary, ternary and quaternary interactions with respect to ball wear during grinding.

Jan 1, 1992

By K. Nielsen

The Norwegian tunnelling industry has made remarkable improvements both with regard to productivity and cost efficiency over the last 30-40 years. This development has been made possible by continuous improvement driven by innovation. Based on a generic description of the innovation process and the innovation system, the paper has used the development of modern tunnel drilling in the Norwegian tunnelling industry to discuss the characteristics of its innovation system with a focus on human capital issues and knowledge management.

Jan 1, 2006

By S. Hodgson

Introduction The Red Dog zinc/lead deposit in northwest Alaska is the second largest zinc deposit ever discovered. Being developed by Cominco Alaska, with startup scheduled for early 1990, it will ultimately be the largest zinc mine in the Western World. Table 1 shows the reserves of the deposit. Bob Baker, a local bush pilot, discovered Red Dog in 1968. The US Geological Survey assessed the find. But the Red Dog site had been withdrawn from staking by provisions in the Alaska Native Claims Settlement Act of 1971 (ANCSA). Under the terms of ANCSA, the deposit was selected by the NANA Regional Corporation, one of 13 native corporations established by the Act. Then, in 1980, the US Congress confirmed this selection, in the Alaska National Interest Lands Conservation Act. In 1982, Cominco and NANA reached an agreement that has led to the development of the mine. Under the agreement, Cominco leases the property from NANA, develops and operates the mine, and markets the concentrate produced. In return, NANA receives royalties and, after capital recovery, participates in the net proceeds from the operation. The Alaska State Government is also playing a role in the development of the mine. Under the auspices of the Alaska Industrial Development Authority (AIDA), the state will construct, own, and operate the DeLong Mountains Regional Transportation System. This consists of a 84-km (52¬mile) road from the minesite to the Chukchi Sea. Located here are the port facilities necessary to store and ship the annual concentrate production and receive the mine fuel and supplies. For using this transportation system, Cominco will pay an annual toll fee. Over the anticipated 50 year life of the operation, the fee will provide a 6.5% return to the State of Alaska. In late 1986, Cominco's Board of Directors approved the Red Dog project. And, during the summer of 1987, road construction began. In February 1988, initial stripping began at the ore body and construction started at the millsite. Project setting The project site is approximately 1000 km (600 miles) northwest of Anchorage, 84 km (52 miles) east of tidewater on the Chukchi Sea, and 192 km (120 miles) north of the Arctic Circle (Fig. 1). The countryside consists of low, rolling hills that lead into mountains north and east of the deposit. The vegetation is typical tundra mat. And the site is in an area of permafrost. However, the permafrost is relatively warm and some areas have been found to be thawed. Examples would be creek bottoms and the site of the main waste dump.

Jan 12, 1988

By J. E. Murphy, L. A. Walters, F. H. Nehl, G. B. Atkinson

The US Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A h/150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 msecs. Graphite, lead and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70°C (158° F) gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10% to 30%, and a period of 100 msecs to 1000 msecs gave the following results: Ag concentrations decreased from 34 µg/mL to 0.1 µg/mL. Au concentrations decreased from 54 µg/mL to 0.2 µg/mL and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 1995

By Peter J. King

Demand for both lead and zinc to the year 2000 will be characterised by modest to nil growth in mature economies, with positive 3 to 4 per cent annual growth rates in developing nations. Asia and China will feature significantly in this growth. Overall lead demand is expected to grow about 1 per cent a year, with industry becoming more dependent on the fortunes of the automotive industry as the lead-acid battery will be the only major end use to expand. Zinc will become more dependent on its main use, galvanising, as the automotive and construction industries move to high levels of dependence on corrosion prevention. Strong growth in zinc consumption in S.E. Asia, China and India is likely to feature widespread development of the continuous steel strip mini-galvanising line technology. Thank you Mr. Chairman for inviting me to this Conference. As an Australian I am honoured to be here to offer some thoughts about future trends in metal consumption -- with particular reference to the role of countries in my own neighbourhood, the developing Asian nations, including China. It is customary for a member of the producer fraternity to speak to the topic of future development. This is no doubt due to the fact that our companies are so often engaged in endeavours to determine the future prospects of the metals as essential background to massive investment decisions relating to the development of new mines and smelters. This is sometimes also applied in relation to the more painful decision of closures of aging operations. In this paper I have drawn upon recent studies by AM&S into the future of lead and zinc. While this work has been thorough and skillful, we are nonetheless left with uncertainty on a number of counts. Firstly. predictions in the past in our industry have not been all that credible. Need I remind a U.S. audience for instance of the Paley ' investigation setup by President Truman in 1950 to study U.S. copper requirements for 25 years in the future. Asarco's Simon Strauss gave those of us daring to forecast long term commodity trends a salutary reminder that the Paley Commission with all the expertise at its disposal missed the mark in its copper predictions by a very wide margin indeed. Additionally, it is difficult to take comfort from longer term economic forecasts. Too many important economic issues remain unresolved suggesting considerable caution. These include the threat of growing protectionism; low economic growth rates with stubborn unemployment levels; and levels of government expenditure at near saturation as a percentage of GDP, to name a few. However, on a more optimistic note. we can look to China, where there appears to be momentum in its economic growth; oil, where stable oil prices to the mid 1990's will contribute to inflation control; and the fact that LDC debt, while still a major issue, is declining in importance and priority. In the short time allocated to us. I wish to deal succinctly with the lead and zinc raw materials supply picture, which is one I do not believe will hold too many surprises for this audience. Following the review of raw materials supply, we will turn our attention to the changes in the pattern of demand towards the year 2000. emphasising the Asian position. In this context. I would like to focus on the theme of the changes in OECD consumption levels relative to those of the emerging nations. One area we will be paying special attention to is China.

Jan 1, 1986

By I. Kapageridis

The mining industry worldwide has recognized in the past the need to apply specific rules and guidelines in the reporting of mineral resources and reserves. The high financial investment and risk associated with any mining project and the ever stricter environmental and social controls were the forces behind this recognition. For years the industry experienced the development and enforcement of several codes for reporting accepted by different countries. The implementation of any code can be a confusing task as the guidelines are sometimes general and open to different interpretation. The use of computers in the estimation and reporting of mineral resources and reserves is necessary, particularly when trying to implement particular code guidelines. This paper discusses ways to implement a reporting code in a computerised resource/re-serve estimation study. The implementation is demonstrated using a gold deposit project as an example. The effects of mining, metallurgical, economic, marketing, legal, environmental, social and governmental factors are taken into consideration. This paper also discusses well established reporting codes and the possibility of reaching a single, universally applied code that could be used by Greek mining companies.

Jan 1, 2007

By L. G. Martin

Early mining at Manhattan demonstrated that blasthole assays alone were insufficient to control the disposition of material. A program was began using controlled blasting, intense sampling and panning of crushed samples, fire assay checks, and geologic inspections to sort material in the pits. Statistical data confirms that the method provides effective control at minimal cost. This cost is easily offset by additional tonnage found in areas considered to be waste.

Jan 1, 1980

By Floyd C. Bossard

A method of hand-calculating the air-cooling requirements of a conceptualized underground mining operation is presented for the reader's orientation. Separate air heat load calculations were conducted for adiabatic compression, electromechanical equipment, wallrock, broken rock, groundwater, and blasting operations. The air heat sources were calculated for four mining levels under conditions representative of a typical planned mining operation at depth. The total heat gain on each level will approximate the level air-cooling requirements. The results of these hand calculations can be further modified by the use of mine ventilation computer software that refine the heat-source calculations, predict underground ambient air temperatures, and establish the air-cooling requirements of a mine. INTRODUCTION The principal mining method employed is a modified vertical crater retreat (VCR) blasthole operation. Typical scopes range from 20 to 40 feet wide, 75 to 100 feet long, and 100 feet in height. Six and one-half inch blastholes are drilled with an "in the hole" hammer drill. Eight-foot high horizontal rounds are blasted down. Mucking of ore from the undercut to orepass is done with LHD equipment operated from a remote control station. Backfill includes hydraulically placed tailings with cement, and waste rock when available. Stope access is from ramp sub-levels on 50-foot vertical intervals. Crosscuts are ramped down to the first stope cut 25 feet below the sub-level elevation. Then the crosscuts are raised by taking down the back when each stope cut is completed, until an elevation 25 feet above the sub-level is reached. The crosscuts are filled with tailings, and/or waste rock. See Figure 1. Typically, a two-pronged approach to defining the air-cooling requirements is conducted. First, the principal sources that make up the air heat load are individually hand-calculated. Second, projections of mine heat load are calculated by utilizing computer modeling techniques. This paper discusses the first method (hand calculations) of determining the individual components of heat flow into the mine. CALCULATED AIR HEAT LOADS Adiabatic Compression The plans for the mine include delivery of 300,000 cfm of air to ventilate the lower level operation. This is equivalent to approximately 200 cfm/ton of rock produced (300,000 cfm/1500 tpd of ore and waste). As air flows down a shaft, with no heat interchange between the shaft and air and no evaporation of moisture taking place, the air is heated in the same way as if it were compressed in a compressor. Dry air increases in temperature about 5.4°F per 1000 feet. One BTU is added to each pound of air for every 778 feet of decrease in elevation, or is subtracted for the same elevation increase. For dry air, the dry-bulb temperature change is 1/(0.24 x 778) = 0.00535°F/ft., or 1°F/187 ft. elevation. Auto-compression may be masked by the presence of other heating or cooling sources, such as shaft wallrock, groundwater, air and water lines, electrical facilities, etc. The major factors influencing the temperature of the air delivered underground by a shaft are (1) the night time cool air temperature's effect on the rock or lining of the shaft, (2) temperature gradient of ground rock related to depth, and (3) evaporation of moisture within the shaft which increases the latent temperature and decreases the sensible temperature. [Calculation For Adiabatic Heat of Compression] a. Assumptions: 1. Three hundred thousand cfm of fresh air at 3000 level has increased in temperature during the summertime to the point where it has little available cooling power. Air-cooling will be required on 3000 Level and below. 2. Elevation of 3000 Level is approximately +1000 ft. above sea level.

Jan 1, 1993

By Peter Joralemon

I want to limit my remarks to epigenetic ore deposits, but do not necessarily subscribe to the classic theories of hydrothermal ore deposition. I will consider an epigenetic deposit as a primary deposit in which the economic minerals have been introduced subsequent to the formation of the enclosing rock, regardless of the source. Past ore discoveries have been made to a great extent by prospecting techniques that have remained relatively constant over the last many decades. In many cases the discoveries have been enlarged or enhanced with the use of technical tools such as geophysics, but theoretical geology, which should serve as a foundation for exploration, has shown little progress of practical importance since the turn of the century.

Jan 1, 1967

By Dennis P. Bryan

The southwestern United States has an abundance of natural lightweight aggregate (NLA) deposits of volcanic origin that are being used in the construction industry within the region. New Mexico, Arizona, Nevada and California utilize NLA in portland cement concrete and concrete masonry units for weight reduction and related economic reasons. The geological environment of the western United States is amenable to the occurrence of natural lightweight rocks because it contains Tertiary and Quaternary volcanic products that include low-density glass and vesicular material. There are two major classical types of natural lightweight materials of igneous origin; pumice and cinder. These account for the vast majority of volcanic rocks that are presently utilized as NLA. Pumice is an ejecta product generally found as part of tuffaceous units associated with nearby siliceous volcanic centers. Cinder, also an ejecta product, is associated with mafic volcanics and is most often found as a cinder cone. Both are highly vesicular. A third type of natural lightweight material, though also associated with siliceous volcanics, is less vesicular than pumice. It is best described as being a slightly pumiceous rhyolite or rhyolite-tuff breccia that occurs as a siliceous dome or tuft unit that is most likely to be glassy. Uses of these natural lightweight rocks center on the construction industry where they are utilized in lightweight portland cement concrete and lightweight concrete masonry units. The major reason for usage in portland cement concrete is cost saving effected by weight reduction in high-rise construction. The major usage in concrete masonry units, or "block", is for weight reduction that enables a mason to lay more lock.

Jan 1, 1987

By A. V. Castelli

The provinces of Guangxi, Guizhou, Hubei (and most recently Fujian) were the prime exporters of barite during this period. Guangdong and Shandong were exporters too but not major participants. These are all primarily agricultural areas so there existed a sufficient labor force willing to work in the mines to supplement their income from farming. During the early years, barite export pushed the existing transportation systems in these provinces to operational capacity. The mines from which this barite is extracted are located about 250 to 1,400 kilometers from the sea ports. Transportation of the ore from the mines to the ports follows a net-work that includes trucking to various rail-heads where it is then shipped via freight trains to ports for loading into seagoing vessels. in some instances, the barite travels by truck or train to the Yangtze River where it is then barged to an ocean port.

Jan 1, 1990

By R. E. Brewer

Pilot scale flotation tests were conducted with a 1-ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pct of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated using the column. The tailings were first water leached at approximately 600 C, and the water-leached tailings, which contained approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH and sodium sulfide addition on gold flotation recovery and redox potentials were examined. maximum gold recovery, 36 pct, was achieved at pH 8.5 with a sodium sulfide addition of 0.18 lb/st.

Jan 1, 1989

By J. E. Shearer

The state of Arizona produced 253,276.2 metric tons (279,000 st) of crude gypsum during 1986. This represents approximately 1.7% of the total U.S. production. Four mines provided Arizona's gypsum, three of these mines are in the San Pedro Valley. The uses of the gypsum produced in Arizona are for manufacture of cement, agricultural uses, and wallboard manufacture. The gypsum is used as a retarder in the manufacture of Portland cement. The use in agriculture is treatment of alkali soils to allow water penetration. Other deposits in the San Pedro Valley have production potential, providing there is sufficient market for additional wallboard. The author completed an evaluation of one property earlier this year.

Jan 1, 1988

By Harold R. Kokal, Madhu G. Ranade

A metallurgical/flux is a substance that is added to combine with gangue (unwanted minerals) during ore smelting, with impurities in a molten metal, or with other additives in metal refining processes to form a slag that can be separated from the metal. Because slags are immiscible with the metallic melt and are of lower density, a separation of the slag and metal occurs if the viscosity and surface tension are of the proper values. The chemistries of slags are adjusted to provide the proper melting point, viscosity, surface tension, conductivity, specific heat, density, or chemical properties to effect the desired task. In addition to absorbing impurities from the metal, the purposes of the slag are to thermally insulate the metal bath, protect the molten metal from the atmosphere, and control the chemical potential of the system. Several excellent references on slags and metallurgical fluxes are available (Boynton, 1980, Lankford, Jr., et al., 1985, Turkdogan, 1983, Rosenqvist, 1974, Fine and Gaskell, 1984). The function of the slag might vary at different stages within a process prior to final melting. For example, the slag composition and behavior will change as materials descend in the iron blast furnace, or as they melt in the early stages of formation of steel- making slags. Selection of the chemistry for a slag might be influenced by factors outside the primary function as when blast furnace slags are used to make cement, rock wool insulation, or fertilizer supplements. Sometimes slags contain a sufficient amount of valuable recoverable elements to be sold as raw materials for other processes. Fluxes are often referred to as acid, basic, or neutral. Acid fluxes are those that generally form acids in water and bases are those that would generally form bases in water. Typical acid fluxes are silica, alumina, and phosphorus, although alumina can function as either an acid or base. Typical basic fluxes are lime and magnesia. Fluorspar, or calcium fluoride, is a neutral substance because it can be viewed as the reaction product of a base and an acid. The degree of acidity (ratio of acids to bases) or basicity (ratio of bases to acids) is often specified to characterize the slag chemistry for a particular system. The system might also be referred to as acid or basic depending on the choice of slag, for example, basic steelmaking uses slags with more bases (lime and magnesia) than acids (silica and alumina). Many forms of minerals and compounds have been used as fluxes depending on the process requirements, availability, costs, requirements for recycling of intermediate products, and environmental concerns. Because slags are most often mixtures of oxides and silicates, fluxes are usually oxides, carbonates (which decompose to oxides) and silicates. Slags comprising phosphates, borates, sulfides, carbides, or halides have also been used (Rosenqvist, 1974, Moore, 1981, Szekely et al., 1989). In ironmaking and steelmaking, some acidic components are sometimes added. In nonferrous processes slags and fluxes are acidic with silica as the primary component, and although the use of basic flux such as limestone or lime is not extensive, some amount is used to modify slag properties and some refining slags are lime based. The production of iron is accomplished by smelting of ores, pellets, and sinter in blast furnaces with subsequent refining of molten iron and scrap in oxygen-blown processes. The electric furnace is used to make steel, stainless steels, ferroalloys, and special alloys, whereas ferromanganese is often made in blast furnaces. Fluxes are used in all of these processes, and either limestone or lime is the major flux component with some dolomite, dolomitic lime, silica, alumina, and fluorspar being used. In ironmaking, the flux is added either by direct charging or through sinter and fluxed pellets. In steel refining by the basic oxygen process, flux is added as lime and dolomitic lime that are either charged as lumps or injected as fines. Some small amount of limestone is sometimes used. Fluorspar is often added as lumps or mixed with other fine materials in briquettes. Alumina is sometimes added to blast furnaces either by direct charging of sized lumps or through sinter. Typical acid fluxes are sand, gravel, quartz rock, used silica brick, or raw siliceous ore (Lankford, Jr., et al., 1985). Olivine, which is a magnesium-silicate mineral, has been added to iron blast furnaces to enhance removal of alkalis (Lankford, Jr., et al., 1985). Alumina in the form of bauxite, aluminiferous clay, and recycled alumina brick has been used as flux. Alumina can function amphoterically as either an acid or base, for example it can form aluminum silicate in high silica slags or calcium aluminate in lime-bearing slags (Lankford, Jr., et al., 1985). Limestone (calcium carbonate) and dolomite (magnesium-calcium carbonate), or fluxstones as they are sometimes called (Boynton, 1980), and their calcined forms, lime and dolomitic lime are the major basic fluxes. In the latter cases, the carbonates are de- composed in a kiln-type process to drive off carbon dioxide that might otherwise interfere with the subsequent smelting or refining process or require expensive forms of energy to effect the decomposition (e.g., by combustion of coke in the iron blast furnace). Limestone is considerably less expensive than lime because it is not calcined; however, lime is far more difficult to handle and reacts readily with water. Dolomite and dolomitic lime are used for their magnesia content. Fluorspar is a neutral flux often used as an additive in steel- making slags to improve fluidity, but it has also been used in combination with lime as a primary slag in electroslag refining (Duckworth and Hoyle, 1969). Fluorspar is available in several grades, with the lowest grade often used for steelmaking. When the price of fluorspar has risen, substitutes including aluminum smelting dross, borax, manganese ore, titania, iron oxides, silica sand, and

Jan 1, 1994

By William E. Wallace, Larry Grayson, Thomas Simonyi, Joel C. Harrison

Application of an SEM-based methodology suggests a reason for past contradictory results on the relationship between quartz and coal workers' pneumoconiosis (CWP). Results indicate that coal seams with the same bulk analysis of quartz have different amounts of surface-available quartz. Our research shows that the amounts of pure and surface-available quartz in a respirable dust vary directly with the rank of a coal seam, except in the case where rock materials are mined. The estimated amount of surface- available quartz therefore provides a measure of the quartz-related fibrogenic potential of a respirable dust.

Jan 1, 1992

By L. R. Berry

The successful selection of a slurry pump depends on the accuracy and completeness of the information provided for the application. Inaccurate or incomplete information can result in incorrect pump selection and / or operational problems. Some information is more critical to the selection process than other information. A full description of the slurry (liquid -solid mixture) including the particle size distribution and maximum concentration, the flow, head and NPSH requirements are most important for successful slurry pump selection and operation. Common problems resulting from improper slurry pump selection will be discussed to illustrate the need for correct selection requirements.

Jan 1, 1996