Search Documents

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By Wilfred M. Kenan

The relationship of various genetic classifications of graphite, their properties and general applications are reviewed. The classifications being amorphous, flake, high crystalline (vein) primary synthetic graphite and secondary graphite. The properties discussed are size, carbon, sulfur, ash content, general chemical analysis and degree of graphitization of each type. The major sources for natural and synthetic graphite powders are discussed in addition to factors which govern the cost as well as the supply. The economics of graphite are basically determined by the consumer and the end application. Graphite is a strategic mineral and is on the government stockpile list.

Jan 1, 1984

Conventional wisdom in the mineral processing industry leads one to believe that pressure oxidation of refractory carbonaceous (preg-robbing) ores is not a practical approach to process development. Initial acid pressure oxidation testing on carbonaceous sulfide ores at the Twin Creeks Mine supported this conventional wisdom. After testing other refractory process options, including air and oxygen enriched roasting, Santa Fe Pacific Gold decided to take a second look at pressure oxidation, using conditions outside the normal range of conventional practice. A combination of very fine grinding and high operating temperature and pressure resulted in significant increases in gold extraction. This paper details the effect of operating parameters developed for Twin Creeks on gold recovery, sulfur oxidation, carbon oxidation/passivation and preg-robb through the laboratory and pilot plant investigations.

Jan 1, 1995

By J. B. Hanlon

In order to protect coal mine owners, operators, and lending institutions from potential environmental liabilities, responsible parties must maintain a thorough understanding of the environmental disposition of the property they control, and the ramifications of impending laws and regulations. The best way to accomplish this is to periodically conduct a Phase I Environmental Audit. The systematic approach of an audit will reveal areas of DOD compliance with SMCRA and EPA regulations which the coal owner and/or operator will be able to use to correct deficiencies and prevent the occurrence of conditions which could lead to permit block, fines, and ultimately reduced productivity.

Jan 1, 1995

By F. L. Kadey

A discussion of fillers would not be complete without allotting adequate time to that unique and different mineral material, diatomaceous silica. Historical references to its use challenge the aesthetic aspect of man's curiosity; whereas modern scientific tools have provided a dimension of measurement that has motivated many of its more recent applications. A brief review of what is already known is in order. The diatom is a unicellular, plant-like, microscopic organism, related to the algae1. Its natural function appears to be that of a food for other marine or lacustrine organisms, The diatom's "claim to fame" from an industrial viewpoint is dependent on the fact that it secretes an opaline siliceous skeleton that must survive, chemically and structurally, the geologic processes that caused its formation in the first place; its subsequent demise, burial, consolidation, and alteration; and finally, its ultimate exploitation by man--in somewhat that order. In addition to its siliceous nature, the skeletal structure of the diatom possesses a variety of shapes, patterns, and sizes that have not only been the intrigue of microscopists for decades, but have served to set diatomite apart as an industrial mineral; and have reserved for it applications that cannot be satisfied by any other material. Its chemical inertness, its intricate structure, and its intrinsic hardness-coupled with fineness and friability-- are generally known and have accounted for its application in a wide range of filtration and filler uses. The increasing use of the electron microscope has considerably expanded our knowledge of heretofore unseen secondary and tertiary structure of submicron dimension in the diatom valve. The development of electro-sensing methods of particle size measurement which seem to supersede sedimentation and microscopic techniques has portrayed size distribution in a more realistic light. Interest in the surface chemistry of these silica structures has further strengthened our understanding for certain uses. Thus, new tools and ideas have made possible the introduction of diatomite into such sophisticated technologies as that of chromatographic supports, its improved utility in paint applications for the control of gloss and sheen, and its usefulness in the entirely new concept of "Dry Acid Concentrates." Each of these applications has been discussed elsewhere before people particularly interested in analytical chemistry, in paint, and in liquid handling, respectively, where the diatom has been a means to an end. The emphasis here, before the mining fraternity, however is on diatomite as a raw material with reference to the uses mentioned above. It is therefore toward an awareness and understanding of diatomite properties pertinent to these newer filler applications that this paper is directed.

Jan 1, 1967

By L. Gertsch, R. Gustafson, J. Rostami, C. Swope

Development of a permanent human base on the moon for exploration requires a self-sustaining system. Such a system entails the production and processing of limited amounts of raw material on the moon. Any mining and construction activities on the moon can only be performed by a robust excavation machine that can excavate a variety of material, from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, a limited amount of information on lunar regolith is available to develop and optimize a machine for lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe, PA. This paper discusses the results of initial material characterization, as well as full-scale tests of a prototype cutterhead in relevant material. A brief review of anticipated production rates under various assumed ground conditions is also presented.

Jan 1, 2010

By Ronald T. Cosburn

The Province of Ontario covers an area of some 400 thousand square miles, however the subject I will be talking about today, the licencing of pits and quarries in southern Ontario, refers to about one quarter of this total area but contains better than 93% of the total population of the province or about 8 million people. Southern Ontario had and still has many inviting features to industry. The Great Lakes almost surround us, hydro power has been relatively inexpensive and abundant, but more in line with our topic today are the ample deposits of sand, gravel and limestone, all of which are used directly or indirectly throughout and are the mainstay of our construction industry. I say we are fortunate to have these non-renewable resources in abundance in close proximity to our industrial and metropolitan areas, but like so many of our resources we have taken them for granted for too long. What has happened in our case, as I am sure is common in many of your own similar situations, because of the recent, current popular trend by naturalists and environ- mentalists to preserve our natural heritage at the expense of all else, through parklands and indiscriminate zoning policies, these once abundant reserves have been tremendously eroded.

Jan 1, 1982

By Josef J. Schwegel

The first vertical shaft lime kiln operating according to the parallel-flow regenerative principle was developed and built in the nineteen-fifties by Schmid-Hofer in Austria. Upon proving this concept of calcining or "burning" limestone to be very energy efficient for the production of good quality lime, Maerz Ofenbau AG of Zurich, Switzerland was in 1965 licensed for the design detailing and construction of these kilns. The first regenerative shaft type lime kiln outside of Austria was built in 1966 and through close co-operation with customers and their operating personnel, the advanced technical developments of today's kiln designs were accomplished. At present approximately 190 kilns of this type in capacities ranging from 60 to 700 short tons per day have been built or are under construction throughout the world in highly industrialized as well as less developed countries.

Jan 1, 1981

WELCOME to the world-class Cripple Creek district where gold exploration and production continue 95 years after the initial discovery. More than 21 million troy ounces of gold have been recovered, valued at greater than $7.8 billion using today's gold price ($371/oz). The Cripple Creek district is localized within and around the margins of a silica-undersaturated alkalic diatreme-intrusive complex. The diatreme appears to be comprised of three sub-basins: 1) a sub-basin east of the Cresson (Fig. 1); 2) a southwestern sub-basin between Victor and Cripple Creek; and 3) a northwestern sub¬basin within which the Globe Hill and Ironclad pits (Fig. 1) are located. The recognition of three separate basins was made by G. F. Loughlin and A. H. Koschmann (1935, Fig. 8) who prepared a contour map on the floor and walls of the composite Cripple Creek basin. The northwestern and southwestern sub-basins are apparent due to the discontinuous exposures of a partially exhumed ridge of Precambrian rocks (Fig. 1). The separation of the eastern and southwestern sub-basins was recognized in mine exposures where a fault-bounded ridge line extends from the vicinity of the Ajax mine toward the Precambrian "island" (Fig. 1).

Jan 1, 1986

By Véronique Falmagne, Chantale Doucet, Thomas Côté

Production began in the Deep 1 zone of Goldex mine in 2017 at a depth of 1,200 m. Stope dimensions are 50 m high by 22 m wide (along strike) and the panel thickness varies between 22 to 35 m. The Deep 1 orebody is 350 m high by 400 m along strike and 200 m from hanging wall to footwall. The mining method is longhole with paste backfill with a three dimensional primary/secondary sequence advancing upwards in a typical chevron approach and retreating from hanging wall to footwall in a V-shape from a central panel. Mining at a depth of 1,200 m in massive granodiorite brings challenges related to seismicity.

Apr 26, 2022

By Paul Javor

Optimization of a process is achieved by selecting, 'from all the known options, the most beneficial method of obtaining a product. It is rare that the optimum process is arrived at by conventional methods, because of the great amount of time required for developing and comparing all the options. On the other hand, it is now possible, by means of an optimization program based on special mathematical formulas involving an algorithm and implemented by a computer, to plot the optimum process realizing considerable savings and in a reasonably short time. The flow sheet arrived at in accordance with the optimization program described in this paper investigates and develops all the possible options and, with the aid of the computer, makes it possible to select the most economical ore beneficiation process. The options in an ore beneficiation process are all the possible trajectories that can be traced through the particle sizes to which the ore is reducible in the extraction of its valuable minerals. Although an ore can have a wide range of composition and several valuable minerals that can be extracted, this paper is concerned with the special case in which only one mineral is extracted from the ore and in which the maximum allowable percentage of impurities in the end product is defined.

Jan 1, 1971

By James W. Mitchell

On December 2, 1942, a scientific team lead by Nobel Prize winner Enrico Fermi first initiated and controlled a self-sustaining nuclear chain reaction. This historic event occurring beneath the stands of the University of Chicago football stadium instantly created an entirely new and tremendously broad area of technology. Indeed, the event probably changed the course of world history and considering the curret energy shortage, it probably came none too soon. Following many technological breakthroughs in the ensuing years, this event led to the first full scale nuclear fueled electric generating plant. In December, 1957, the Shippingport Nuclear Power Plant became operational and the United States had entered the era of the nuclear fueled electric generating station. Today, only fifteen years later, there are some thirty-five operating nuclear power plants in the United States with another 56 under construction and 116 on order. Still, we are only scratching the surface of this tremendous energy source. In 1970, less than one-percent of the total electric generating capacity in the United States was nuclear fueled. By 1985, it is projected that 45% of our generating capacity will result from nuclear power plants. These projections are based upoa statistics of six months to a year ago and considering the current energy shortage and recent attempts by the United States Atomic Energy Commission (USAEC) to speed the licensing process and encourage standardized plants, the contribution of nuclear power to our total generating capacity may be even greater. In summary, it is obvious that nuclear power is now, and will continue, playing an important role in our future. Those factions of government, industry and the professional community charged with fully developing this tremendous energy source must deal with it rationally, logically and expediently. The various environmental considerations in nuclear plant siting play an important role in the overall plan.

Jan 1, 1974

By D. W. Park

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floor and thinly-laminated immediate roof. The investigation covered by this paper concerns a mine that was experiencing ground-control problems with weak floor conditions. Four hundred ft above the presently producing seam, another seam has been mined out. Several roof falls occurred locally, and as much as two ft of floor heaves have been experienced. The paper presents the results of comprehensive analysis conducted on floor heave, roof sagging, and the influence of the mined-out seam using instrumentation and numerical analysis.

Jan 1, 1991

By T. Grounds, K. Singh, W. R. Reed, R. Cross, G. Ross, S. Klima, M. Shahan

"A 2nd generation roof bolter canopy air curtain (CAC) design was tested by National Institute for Occupational Safety and Health (NIOSH) at a Midwestern underground coal mine. During the study, the roof bolter never operated downwind of the continuous miner. Using a combination of personal Data Rams (pDR) and gravimetric samplers, the dust control efficiency of the roof bolter CAC was ascertained. Performance evaluation was determined using three methods: (1) comparing roof bolter operator concentrations underneath the CAC to roof bolter concentrations outside the CAC, (2) comparing roof bolter operator concentrations underneath the CAC to the concentrations at the rear of the bolter, and finally, (3) using the gravimetric data directly underneath the CAC to correct roof bolter operator concentrations underneath the CAC and comparing them to the concentrations at the rear of the bolter. Method 1 dust control efficiencies ranged from -53.9% to 60.4%. Method 2 efficiencies ranged from -150.5% to 52.2%, and Method 3 efficiencies ranged from 40.7% to 91%. Reasons for negative and low dust control efficiencies are provided in this paper and include: incorrect sampling locations, large distance between CAC and operator, and contamination of intake air from line curtain. Low dust concentrations encountered during the testing made it difficult to discern whether differences in concentrations were due to the CAC or due to variances inherent in experimental dust measurement. However, the analyses, especially the Method 3 analysis, show that the CAC can be an effective dust control device. INTRODUCTION Canopy air curtains (CAC) have been shown to be an effective respirable coal mine dust control for roof bolters in a laboratory setting with dust control efficiencies ranging from 14% up to 75% [Goodman and Organiscak 2001, Listak and Beck 2012, Reed et al. 2017]. Unfortunately, there is limited information on their effectiveness for controlling respirable coal mine dust in the field. On continuous miners, CAC dust control efficiencies ranged from 23% to 69% [Krisko 1975]. Two underground tests of the CAC on roof bolters demonstrated dust control efficiencies of 35% and 53% [Listak and Beck 2012] before problems occurred with operation of the CAC. Since the implementation of the new respirable coal mine dust limit from 2.0 mg/m3 to 1.5 mg/m3 (Code of Federal Regulations, 30 CFR 70.100, 2015), roof bolter CACs are becoming more commonplace in underground coal mines as a dust control tool to prevent roof bolter operator overexposure to respirable coal mine dust. J.H. Fletcher & Co. has been instrumental in delivering an effective design which incorporates the filter, blower, and canopy plenum seamlessly into the design of the roof bolter, resulting in a successful operational roof bolter CAC."

Jan 1, 2018

By Harry Teicher

The subject of Specialty Silica Products could encompass a broad range of materials, some of which would be familiar to members of the Society of Mining Engineers. With the concurrence of your chairman, I have chosen to limit my remarks to synthetic materials, not including such siliceous materials as diatomaceous earth, asbestos, quartz and clays. For purposes of discussion, I have classified Specialty Silica Products into two groups -- powders and liquids -- which I will discuss in that order and which are categorized in Figure 1. The synthetic silica powders are amorphous to x-rays and are manufactured by various processes resulting in products of a wide range of physical and chemical properties, as well as functional performance and applications. Applications or functional properties are generally dependent upon such physical properties as micron-sized particles exhibiting large surface areas per unit weight and low apparent bulk density. Their presence in various systems modify surface properties. As summarized in Figure 2, they act as viscosity modifiers, flow conditioning agents, anti-slip agents, anti-blocking agents, flatting agents in surface coatings, reinforcing agents in polymers such as silicone rubber and numerous other applications. Although the various types of silicas exhibit various levels of functional performance in these end uses, they are not usually equally effective as direct replacements and I will briefly discuss the various types of materials.

Jan 1, 1974

By N. P. Titkov

This paper presents the results of laboratory and pilot plant investigations for the development of efficient methods of beneficiating hematite ores from the Krivoi Rog, Kursk Magnetic Anomoly, Olenogorsk, and other localities. The tests included gravity, magnetic (in a high intensity field), flota¬tion, and magnetizing roasting methods. It was possible to develop efficient beneficiation methods depending on the mineral composition of the ore and degree of dissemination of ore and gangue minerals. The paper shows the relationship between the iron silicate and quartz content of the ore and the technologic indices of the various beneficiation methods. Some of the conclusions based on these investigations and the technical and economic computations related to the cost of one ton of pig iron produced from concentrates obtained by the various beneficiation methods are: 1. If the hematite ore is not disseminated uniformly, it is expedient to use a combined gravity and flotation process. Ore particles up to 50 am. in size are beneficiated by gravity (heavy suspension, jigging, and others) and yield a lump concentrate. The middlings from this process are recrushed and floated; 2. Finely disseminated hematite ores, containing small quantities (less than 5 percent) of iron silicates, are most effectively beneficiated by flotation. Anionic (sulphate soap, tall oil emulsion with various foam depressors) as well as cationic collectors may be used. Depending on the mineral and chemical composition of the ore, it is possible to obtain concentrates containing up to 65 percent iron with an extraction up to 94 percent; 3. Finely disseminated, mixed hematite-magnetite ores may be beneficiated by flotation or a magnetic separation-flotation process; 4. Finely disseminated hematite ores, containing large quantities of iron silicates and earthy hematite ores are most efficiently beneficiated by the magnetizing roasting method. This method will yield concentrates containing up to 68 percent iron with extractions up to 90 percent. Although beneficiation by the magnetizing roasting process is costly, it will nonetheless, when employed on this type of ore, yield the least expensive pig iron.

Jan 1, 1960

By R. Schipper

Two bench scale biochemical reactors (BCRs) were operated over a period of 3 months for the removal of uranium, radium, and selenium from mining influenced water (MIW). A BCR is an anaerobic reactor comprised of organic and inorganic substrate including woodchips, straw, sawdust, and limestone. Uranium and selenium are removed in a BCR by biological reduction of oxidized species (i.e., selenite, selenate) to less soluble forms (Pahler et al. 2007, Blumenstein et al. 2008, Rutkowski et al. 2013). It is believed that radium may be removed through absorption to the biomass in the BCR. The bench scale BCRs were constructed of 6 inch PVC columns with a top to bottom flow configuration. The bench influent water consisted of three different water ratios from two adit seeps. BCR hydraulic retention times of 24 to 36 hours were targeted during the study. Influent concentrations ranged from 19 ug/L to 1.86 mg/L for dissolved uranium, 12 ug/L to 270 ug/L for dissolved selenium, and 4.9 pCi/L to 24 pCi/L for radium 226. The average and maximum dissolved uranium removal was 93.6% and 98.5% respectively, the average and maximum dissolved selenium removal was 93.3% and 98.9% respectively, and the average and maximum radium 226 removal was 89.5% and 100% respectively.

Feb 23, 2014

By Thomas D. Henderson, Wayne R. Hopkins, Arthur Lynch

Brought on stream in 1975, the 10,000-tpd copper oxide processing plant of Anamax Mining Co. at Twin Buttes, Ariz., is now at design capacity. Based on acid agitation leaching, solvent ion exchange, and electrowinning, the Anamax plant bridges an ore to metal gap by producing mine site copper cathodes from lime-bearing oxidized feed. Until recently, such material was considered submarginal because copper recovery was uneconomic using conventional methods. The new Twin Buttes oxide plant, the largest of its kind in North America, is one stage in the expansion of Anamax, a joint venture owned equally by The Anaconda Co. and Amax Inc. Other phases include an accelerated stripping program in the pit, an expansion of the sulfide concentrator from 32,000 to 40,000 tpd, and construction of a 57 MW diesel generating station for the oxide plant. Once the basic oxide flowsheet had been selected, Anamax awarded a contract to a joint venture of Arthur G. McKee and Co.' (Western Knapp Engineering Div.) and Davy Powergas' (a member of the Davy International group). The contract covered process design, engi¬neering, procurement, and construction. The property, identified by Banner Mining Co. in the 1950s and developed by Anaconda, was put into production in 1965 as an open pit mine equipped with a 32,000-tpd sulfide flotation concentrator. The Twin Buttes mine has since become one of the largest earth¬moving operations in the world, excavating some 10 tons of waste per ton of ore. At the original sulfide mill feed rate, the mining fleet moved 375,000 tpd of material (225,000 tpd alluvium and 150,000 tpd of rock). The most significant copper mineral in the ore body is chalcopyrite, which is scattered in pockets of weak mineralization. Cap oxidation has progressed to depths of several hundred feet, principally as chryso¬colla. Present estimates place minable reserves at 347 million tons of sulfide ore grading 0.6% copper and 55 million tons of oxide ore grading 0.9% recoverable copper from 1.25% total copper. The nonre¬coverable fraction is composed of native copper and insoluble copper oxides and sulfides. The oxide ore has been partially stripped, and 25 million tons having a copper content greater than 0.6% have been stockpiled. The stripping of oxide ore to expose sulfides will continue for several years. The copper oxide studies launched by Banner Mining in the 1950s were continued by Anaconda. Process routes investigated included: acid leaching; cyanide leaching; segregation roasting; chlorination, oxidation, and reduction; flotation in combination with leaching; cal¬cite flotation plus leaching; copper oxide flotation; and sulfidization flotation. By late 1968 test work favored a low temperature roast followed by an ammonia-ammonium carbonate leach of the ore. During this period, acid leaching had been discounted because of excessive con¬sumption of expensive acid by the high limestone ore matrix. Restric¬tive SO2 emission controls in 1971 suggested an increase in acid production and availability at a lower cost. Research then switched to acid leaching, resulting in development of the present flowsheet. Mechanically agitated leaching in a cascaded series of tanks was selected in preference to vat leaching after piloting a stirred-tank system. Preliminary testing of vat leaching indicated that inter-vat solution clarification problems could be caused by gas evolution from leaching of high limestone ore. Lack of research time for resolution of this problem, plus success of the pilot agitation system, dictated the final flowsheet selection. In 1973 Anamax decided to proceed with agitation acid leaching to produce liquor for a solvent ion exchange (SIX) and electrowinning (EW) installation. At that time, such systems were proving their eco¬nomic viability, and they allowed direct recovery of high quality cath odes while bypassing the smelting and refining of lower grade cement copper precipitates. The Anamax oxide plant processes a grade of about 1% recovera¬ble copper from stockpiled sources and new mine production. Unit operations include size reduction, agitation leaching, countercurrent decantation washing of residue, pH adjustment of solution, clarifica¬tion, solvent ion exchange, and electrowinning of copper, with a mini¬mum of environmental impact. The feed to the primary crushers is composed of: 1) -10-in. stockpiled oxide ore, which has passed through the mine crusher and has been grade-segregated to allow blending for a consistent feed material. 2) -4-ft ROM oxide ore stockpiled in the early mining operation. 3) -10-in. ore currently being mined. Ore is delivered in 100-ton mine trucks to a dump pocket, where an apron feeder transfers the ore to an inclined 6-in. fixed grizzly. The grizzly oversize passes through a 48 x 60-in. primary jaw crusher, where it is reduced to -6 in. The fixed grizzly undersize and the crusher product are conveyed to a 4-in. vibrating grizzly. Oversize from this grizzly reports to a 7-ft Standard cone crusher, where it is reduced to -1 in. The crusher product and the vibrating grizzly undersize are conveyed to two 8 x 20-ft double-deck vibrating screens that operate in closed circuit with two 7-ft short head cone crushers. Screen undersize (-1/2 in.) is delivered to a covered conical fine ore stockpile with a designed live capacity of 15,000 st. Beneath the stockpile are ten Pioche belt feeders feeding two conveyor belts that supply the milling circuits. Each group of five feeders has two variable speed and three fixed speed drives. Grinding to 95% -48 mesh is done in two parallel lines, each consisting of an 111/1 x 18S -ft rod mill and a 12' x 30-ft ball mill in open circuit. Water is added to maintain a pulp density of 72% solids in the mills. Further water additions are made to the ball mill discharge sumps to create a 60% solids slurry for transfer to the leaching reactors. The nominal grinding rate is 440 tph solids. A splitter box on the product from the mills separates the incoming slurry into two streams, one for the leaching reactors and the other for the pH adjustment reactors. This split is determined by the lime content of the feed material and the pH of solution entering the pH adjustment reactors. Five 30-ft diam by 31-ft high mechanically agitated, rubber-lined leach tanks are arranged in cascade, with gravity transfer from one to another by enclosed launders. Concentrated sulfuric acid (93.2%) from storage is added to the pulp principally at the first leach tank, and the reacted slurry leaving the cascade after a 5-hr residence time at 50% solids is pumped to countercurrent decantation (CCD) wash thickeners.' At this point, most of the soluble copper has been leached from the ore. Up to 250 lb of sulfuric acid is consumed per ton of ore, the acid being supplied in tank cars from a nearby smelter. Leached slurry at 50% solids is washed countercurrently with return raffinate from the SIX plant in a series of four Doff-Oliver center caisson, 400-ft diam thickeners. Solids advance from thickeners No. I through No. 4 to the tailings dam. SIX raffinate advances from thickener No. 4 to thickener No. l, where a pregnant solution overflows to pH adjustment. To optimize solvent extraction, the pH of the pregnant solution from CCD thickener No. I is adjusted from 1.5 to 2.5 by adding unreacted ground slurry (split from the grinding circuit) to the preg¬nant overflow of No. I CCD thickener. The resulting slurry is retained for 45 min in three mechanically agitated leach tanks. CO, generated during leach and pH adjustment is ducted to a demister, where entrained acid droplets are removed. The cleaned CO, and the No. 4 CCD underflow are the only effluents from the plant. The underflow of No. 4 thickener mixes with tailings from the sulfide concentrator and is neutralized. Slurry exits the pH adjustment vessels at about 10% solids and

Jan 1, 1985

By Robert G. Ditchburn

The Mariana arc is an ~1,400-km-long intraoceanic arc that marks the southern extension of the Izu-Bonin arc, and is host to 62 ?volcanic centers? of which at least 27 (21 submarine) are hydrothermally, or volcanically active. A surface ship cruise in early 2003 mapped the distribution of hydrothermal plumes emanating from these centers, followed by remotely operated vehicle (ROV) cruises with ROPOS in 2004 and Jason II in 2006. With the exception of one volcano (East Diamante), none of the vent sites visited by the ROVs were host to sulfide mineralization. Rather, they were characterized by high sulfidation mineral assemblages dominated by native sulfur. The sulfur was seen marking the vicinity of vent sites, or as sulfur ?chimneys? (e.g., NW Eifuku and Nikko), or more spectacularly as ?lakes? of molten sulfur, either occupying the summit crater of the volcano (e.g., Nikko), or perched on the flanks of the volcano, near the summit (e.g., Daikoku). Gas (H2S and CO2) was discharging through the molten sulfur. Evidence for these lakes to have either been substantially ?deeper? in their recent past (e.g., Nikko), or existing at other volcanoes (e.g., Seamount ?X?) is given by remnant ?pillars? of native sulfur that are reminiscent of rock pillars in lava lakes found along mid-ocean ridges.

Jan 1, 2008

By A. Janwong

Ion exchange technology is becoming more prevalent for metal recovery from low concentration solutions. The products of ion exchange are typically a metal free stream (product stream) and a concentrated metal stream (byproduct). The metals in the concentrate stream are usually precipitated and returned to the process or discarded. The unique features of emew® technology enable metals to be recovered directly from the concentrated stream. The advantage of the IX-emew® combination is the ability to have two product streams: 1) clean metal free solution and 2) metal product for sale. In addition to recovering metals from solution, it is also possible to separate metals from each other and recover more than one metal product. In this paper, examples of IX-emew® combinations are detailed including the recovery of copper, nickel and cobalt from an industrial waste stream, recovery of nickel from a spent electroless nickel plating solution and recovery of cobalt from an hydroxide cake.

Feb 23, 2014