Search Documents

By A. Haghighat

The Missouri University of Science and Technology?s (Missouri S&T) Experimental Mine is a teaching and research facility which has been excavated in limestone by mining engineering students over almost 100 years. The mine is currently being extended to a second level. Available fans for ventilation are two surface fans of 24 kW and two underground booster fans of 12 kW. The design of a ventilation network in conjunction with multi surface fans and booster fans entails a complex procedure. Ventsim Visual software modeling has been used for network analysis to determine the optimum surface and booster fans locations, blade settings, and speeds. Both natural and mechanical induced ventilation pressures have been taken into account. Three working faces on each level have been designated as target points that minimum air quantities are required. The model has been calibrated against a pressure and quantity survey. Design of ductwork, door/stopping positions and different fans characteristics have been examined. The optimum flow rate at identified working faces, efficiency and minimum energy losses and annual network power cost determine the best scenario. The optimum design has been determined for the ventilation network for the next 100 years. The optimum flow rate across working faces is the key criterion selected.

Feb 23, 2014

By E. Oraby, S. Garcia, A. Thurgood, D. Bertoldi, G. O’Malley

Mining and Process Solutions (MPS) most advanced process, GlyCatTM is the only process that can be easily adapted to existing cyanidation plants in the market today whose real advantages over cyanidation are when treating copper containing ores, concentrates or tailings. With such complex material, GlyCatTM requires 70-90% less cyanide addition to achieve the same precious metal extraction. However, GlyCatTM is not simply cyanidation with added glycine. It is a completely different process where the solution chemistry and conditions needed to effectively leach the precious metals are quite different. Downstream however, the process is largely unchanged as the recovery of the leached gold and silver uses existing known processes such as conventional activated carbon or zinc cementation (Merrill-Crowe process). Another advantage is lower SCN, OCN, WAD and no free cyanide in the effluent which can substantially reduce cyanide detoxification requirements and decrease the OHS and ESG risk of the operation. This paper outline some of these differences and presents testwork, piloting and process examples to highlight the advantageous of this new process over conventional cyanidation.

Feb 1, 2023

By M. Z. Emad, M. U. Khan

"Coal mines opting for longwall mining or its variations rely on the main and tail gates for production. Stability of these entries or crosscuts is crucial in coal mining operations. Roof or strata failure can be fatal, may lead to property loss and delay in production. Failure of the gates depends upon many factors including the mining method, panel dimensions, pillar width, mine depth, caving rate, dimensions of gates and roof strength properties. In Pakistan coal is mined through a variation of longwall mining method with almost no mechanization while using timber as a primary support. Timber support as chock is very useful in coal mines especially in overhanging face. Similarly gate entries and coal faces are supported by chock supports throughout their length. In this paper the stability of the longwall gate is assessed for a typical coal mine in Pakistan by using finite element code. Numerical modelling considerations for gate entries are discussed. A model parametric study is performed for key factors. The results showed that the existing mining practice is not suitable and there is a need to review the mining approach. INTRODUCTION Main and tail gate entries leading to longwall mining panel play a crucial role in production cycle. Failure of any of these may lead to loss of life, property and production delays. The stability of gate entries depends primarily on the nature of loading and stresses incurred. It is relatively easier to assess the ground response to production for common longwall mining panel. In thin-seam coal mines the gate entries are generally supported throughout their length by timber made chock supports. The tailgates receive huge deformations and stresses during the mining and backfilling cycle. The chock supports are required to take care of rock falls leading to blockage of entries causing production delays and loss of capital. A number of supports are available for supporting the gate entries (Hoek and Brown 1980; Brady and Brown 1985). The support system can be selected based on load-deformation characteristics including the yielding behavior, pre- and post-yielding behavior (Barczak, 2003). The principal of support selection is that the support characteristics must match the ground response in order to maintain the gate entries (Mucho, et al., 1999). It has been observed that thin-seam mining (<1 m) is very challenging and it is necessary to develop an understanding of ground mechanics before the selection of an efficient support system Dolinar (2003). The chock supports have been tested for load-deformation characteristics in the laboratory (Barczak 2003). But the ground and support interaction, response and loads must be assessed for individual site. This can be accomplished by in-situ testing and observations at few locations. The generated data is generally insufficient for complete understanding. Numerical models can combine the data generated in the laboratory and on-site to fulfill the requirements."

Jan 1, 2017

By Hans Ruge

The El Soldado copper mineralization occurs as relatively high-grade irregular ore bodies with assay contacts and with frequent inclusions of barren rock. The sampling method must be timely for production grade control purposes, as well as accurate and inexpensive. Sampling techniques evolved from sampling dump cars at the haulage level to sampling scooptrams at the loading pockets. These were abandoned in favor of sampling production blast holes. Several sampling alternatives are discussed. These involve the selection of optimum volumes and sampling frequencies while taking into consideration geological parameters and statistical analyses of sampling data.

Jan 1, 1984

By H. H. Hayden

The accident repeater-40 you have one at your mine? Unless your company is vastly different from most coal companies, you will find that a small percentage (11-12%) of your employees will have a large percentage (47-50%) of your accidents. When you find out that this is a fact, what do you do? First, you establish a set of guidelines that can be used in identifying the ?accident repeater?. Next, you determine the type of action necessary to improve work habits and safety performance of the accident repeater. With these two steps in mind, objectives are developed for an ?accident repeater? program.

Jan 1, 1984

By Robert A. Westman

The INRED process has been developed step by step by Boliden since 1972 at MEFOS, the Foundation for Metallurgical Research, at Lulea in Sweden. The demonstration - plant is number five in this series. The purpose of this plant, which has a nominal capacity of 60,000 tonnes per year of hot metal is to: 1) prove the process on a sufficiently large scale to provide the basis for construction of production plants, 2) test various kinds of raw materials on behalf of licensees, 3) train operators of the first production plant, 4) develop the process further for special applications.

Jan 1, 1983

By L. H. E. Weyher

Minerals beneficiation commonly requires initial crushing and grinding so that the mineral phase we seek to concentrate is adequately liberated to obtain a product of specified grade at optimum recovery. To some degree this also is true for coal preparation. In the comminution process we liberate not only the product but also the tailings phase. The true objective is, therefor, to eliminate from the comminution circuit whatever particulate matter has reached specified liberation, regardless of whether the particle is product or tailings material. Overgrinding either of the two phases ties up mill capacity and usually also burdens the downstream processing steps by increasing costs or decreasing recovery, or both. In view of this situation, one would expect concentration steps to be commonly incorporated into the cominution circuit. The reasons this is not done may vary, but probably include the desire to utilize large scale unit operations, e.g., large mills, in conjunction with very simple processes. Hydrocyclones have satisfied this desire but may not always be employed for the right reasons. Hydrocyclones are indeed simple. They also are rugged and forgiving. Unfortunately, these virtues are frequently misused. The direct results are inefficient classification and overgrinding. The indirect results are added costs through recovery losses, unnecessary recirculation, and so on,

Jan 1, 1985

By H. T. McAdams

The logic of regression analysis as an operations research tool is critically examined, and a formal basis for its application to mining problems is developed. The traditional view of regression analysis as a statistical discipline does not provide an adequate basis for evaluating a regression model in a specific area such as ore reserve calculation or process control. In particular, the validity of the residual-sum-of-squares criterion is questioned, and the need for a criterion based on interpolative features of the model is emphasized. Strictly speaking, a regression model is statistically supported only at points at which observations are available, yet inferences are drawn with regard to a continuum. When considered as a mathematical function, therefore, the model is observationally defined only on a domain consisting of a finite number of points. Extension of this domain to an interval of the real line must be based on physical rather than statistical argument. Vector space and function theory concepts useful as a logical framework for a physically oriented problem analysis are discussed and their usefulness demonstrated in a practical problem.

Jan 1, 1966

By T. J. Batchler

"INTRODUCTION A variety of standing supports are being applied in underground coal mining operations to assist in providing stable mine entries. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Considerable research and development has been conducted by support manufacturers to develop standing support technologies for the mining industry. The National Institute for Occupational Safety and Health (NIOSH) researchers, with the cooperation of various support manufacturers, have developed a testing protocol that evaluates performance characteristics of these standing support systems.. Using this protocol, each of these support systems has gone through rigorous safety performance testing under controlled loading conditions in NIOSH’s Mine Roof Simulator (MRS). It is important to understand the unique performance characteristics of each type of standing support. This information allows mine operators to determine if the support system is compatible with the conditions in the mine and to compare each support system and determine if that support will provide equivalent or improved support capability. This paper provides a comprehensive summary of support performance to facilitate this objective. SUPPORT DESIGN CRITERIA AND THE GROUND REACTION CURVE Standing roof support systems are designed to prevent unplanned roof falls. The selection of the standing support is based on the interaction of the support with the surrounding rock mass, and its function is to assist the primary support system in maintaining the integrity of the immediate roof. The standing support works to control the immediate roof structure by resisting deformation that contribute to delamination of the bedded layers and displacements that lead to separation of the bolted zone from stable roof structures above the bolted horizon (Barczak, 2005). Standing supports should be installed early enough and develop sufficient capacity to bring deformation of the ground into equilibrium before a critical deformation is reached that leads to a detached block condition, at which point the standing support will be required to carry the entire dead weight of the detached rock mass to prevent a roof fall from occurring (Mucho, 1999). The ground reaction curve (GRC) can be used to assist in determining the compatibility and design requirements for a support system. It is important to understand the significance of the ground reaction relative to the support design requirements. The ultimate objective is to match the support behavior to the ground response and create equilibrium (stability) of the rock mass. This equilibrium is accomplished when the support loading intersects the ground reaction curve (Figure 1). Essentially, the ground reaction concept implies that the convergence in the mine entry is controlled by the magnitude of the support resistance. However, as a passive support, the standing support develops its loading through convergence. As such, the support needs to maintain its load capacity through the associated deformation of the ground and resulting entry convergence until the equilibrium condition is reached. This requirement causes factors such as the support stiffness, peak capacity, yielding characteristics, and stability to be fundamental to proper support design and application. NIOSH contributes to providing this understanding through full-scale performance testing of support products in the Mine Roof Simulator."

Jan 1, 2017

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy&apos;s program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By Lennart Bergstedt

Boliden Aktiebolag, the prime base metal mining company of Sweden, annually treats some 11-12 million tons of sulphide ore in nine concentrators. Its first flotation plant was established in the early thirties for the complex Boliden ore. Since then, the number of mines and plants has gradually increased. Considerable effort has been devoted to the development of all phases of the technology of ore prospecting, mining, milling, smelting and refining. This has been necessary due to the complex and low-grade ores. The development of concentration has mainly been directed toward the arts of grinding and flotation. During the forties and fifties, open-stage fine crushing followed by two-stage grinding in rod and ball mills with cyclone classification was successfully introduced and used throughout the plants. The increasing cost of grinding media led to studies of an autogenous grinding technique as early as 1945. Basic test work commenced during the early fifties, with a. number of ores tested for pebble grinding. In 1956 a new pilot plant was built, with equipment installed for the continuous testing of pebble grinding and, later, for primary autogenous grinding of run-of-mine ore. The intensive test work showed that pebble grinding was feasible in almost all of the plants. At this early stage of testing, however, the merits of autogenous grinding could not be fully evaluated. As a. consequence the rod mill/ball mill grinding systems were converted to rod mill/pebble mill systems whereever possible. In parallel with the converting of grinding systems the development work concerning the merits of autogenous grinding went on. The major result

Jan 1, 1977

By Wolfram Schnabel

Recently Lurgi has succesfully commissioned Peru&apos;s first direct reduction rotary kiln at SIDERPERU?s Chimbote works. The order included comprehensive engineering services and supply of special equipment to modify three existing cement kilns according to the SL/RN process. The kilns were cut to 62m length and installed with a slope of 2.5%. A new heating system, including shell burners, was supplied and inlet and outlet ends of the kilns completely renewed. Figure 1 shows the kilns after modification.

Jan 1, 1981

By Arthur A. Schweizer

A method to improve the quality of Magmnt zinc concentrates to become acceptable feed to an electrolytic zinc refinery. The magnesia content of zinc concentrates produced was too high due to particle locking with the sphalerite in coarse fractions. Regrinding of the concentrates to a very fine particle size and then refloating the sphalerite was chosen to eliminate a sufficient amount of the magnesia to make the concentrates acceptable.

Jan 1, 1981

By E. Bakhtavar

It is considered that the most economical method for the exploitation of Gol-e-Gohar Area 3 iron ore mine is to combine open-pit and underground methods. In this regard, the most critical problem is the determination of optimal final pit depth. In this paper, a method which was recently introduced on the basis of economical block models of open-pit and underground is used to determine optimal final open-pit depth of Gol-e-Gohar Area 3 mine with due regards to the future underground mining option. Considering a low cost and productive underground method as a feasible alternative for extraction of the lower part of this deposit, room and pillar was selected. It is concluded that after the assessment and comparison of different values for depth, optimal final open-pit depth was determined to be equal to 285 m.

Jan 1, 2010

By Ben W. Burdett

Since the late 19701s, the use of microcomputers in the minerals industry has grown to the point where today they can be found in virtually every plant within the industry. Their use in every aspect of instrumentation and control has increased the ease of operation and control of every phase of mineral processing. Their incorporation in sensors, transmitters, indicators, and controllers in addition to their use in distributed control and computer systems has provided operators with more timely accurate information than they have ever had before. This has led to an increase in the operator&apos;s effectiveness and an improvement in overall productivity. The ultimate aim of plant control is to maximize recovery in the mineral processing operation, and the microcomputer has spawned many tools that are now making this goal attainable. This paper discusses individual use of microcomputers in the areas previously mentioned as well as their collective use in overall control systems. The incorporation of local control systems in total plant control including the communication of information throughout all levels of plant management is also discussed. Finally the role the microcomputer is playing in today&apos;s plants is illustrated with numerous references to current examples.

Jan 1, 1985

By A. G. Fonseca

The effects of coal cleaning, coal combustion and flue gas particulate removal systems on the partitioning of 12 trace elements were investigated. This study was prepared to help document the fate of trace elements in modern coal preparation plants and coal-fired utility boilers. The coal cleaning data were obtained from several coal preparation plant operations. The CONSOL 1. 5 MM Btu/hr pilot combustion and electrostatic precipitator (particulate removal system) test facility was used to develop the combustion systems data. A comparison with the very limited amount of published data from utility boilers is presented.

Jan 1, 1993

By Jack G. Quade

During the summer and fall of 1973 a series of Skylab and high-altitude aircraft overflights provided excellent hard-copy photographs of the Great Basin. These photographs, with a wide range of ground resolution were used by the NASA Project of the University of Nevada, Reno, to conduct specific geologic studies. The principal objectives of these studies were to: select individual areas covered by Skylab photography for detailed studies, develop mapping techniques using varied film-filter products with a wide range of ground resolution, compare the results of the mapping techniques to existing geologic maps at comparable scales, verify the results wherever possible by direct field observations. These studies were conducted by Jack Quade and Dennis Trexler and by graduates and undergraduates of the Reno campus under a contract with the Manned Spacecraft Center Houston, Texas.

Jan 1, 1976

By E. W. Sawyer

Gelling-grade attapulgite and sepiolite clays are employed as thickening agents for the preparation of ionically contaminated drilling fluids where the use of fresh water clays are unfeasible or impossible. Attapulgite and sepiolite are nonswelling clays that can be dispersed and reflocculated by mechanical and chemical means to increase the viscosity of fresh water, salt containing waters, gypsum contaminated waters and fluids containing cement. Such gelled systems are quite stable in viscosity properties and can be further treated with other necessary additives such as thinners, water loss reducers, weighting agents, surfactants, etc. Many of the oil well drilling fluid practices have influenced such technologies as water well drilling, foundation drilling and waste disposal. The use of salt water gelling clays in these fields will be described and compared to oil well drilling.

Jan 1, 1986

By F. D. Ayhan

The aim of this study was to investigate desulfurization and de-ashing of a mixture of subbituminous coal and gangue minerals by the agglomeration method. For this purpose, experimental studies were conducted on a mixture containing subbituminous coal, pyrite, quartz and calcite. The effects of some parameters that markedly influence the effectiveness of selective oil agglomeration, such as solid concentration, pH, bridging liquid type and concentration, and depressant type and amount, were investigated. Agglomeration results showed that the usage of various depressants (Na2SiO3, FeCI3, corn starch, wheat starch) in the agglomeration medium has a positive effect on the reduction of ash and total sulfur content of agglomerates. It was found that an agglomerate product containing 3.03% total sulfur and 25.01% ash with a total sulfur reduction of 56.71% was obtained from a feed that contained 7% total sulfur and 43.58% ash when FeCI3 was used in the agglomeration medium. Key words: Desulfurization, De-ashing, Agglomeration, Coal, Gangue minerals

Jan 1, 2009

By R. Raby

During the 1980 decade, the rapid price increase for flake graphite has generated a high degree of interest for the discovery and the development of alternate occidental sources of supply in response to fluctuations in quality and availability from current producers. Alike many industrial minerals, graphite draws its complexity not only from its mineralogy and unique properties but also from the very large spectrum of industrial applications each calling for specific quality criterion. As new high technology uses are being developed, more rigid specifications will apply. Discovered during the latter part of 1988 by Mazarin inc., some 30 Km South of Fermont near the Quebec-Labrador border, the Lac Knife deposit was quickly identified as one of the world major long term alternate source of stable supply for this mineral. This paper also reviews the status of the project development as of late 1991, while updating previous papers published by Industrial Minerals1990 and Mining Magazine 1990.

Jan 1, 1992