Search Documents

By M. H. Rauschkolb, J. A. Cremeens

Geotechnical solutions were developed for closure of two historic, remote underground mines in the deserts of southern California. Closure criteria included access closure, minimal site impact, and optimum use of native materials. The closure designs and construction activities incorporated techniques for protecting sensitive biota, particularly bats and desert tortoise. The types of mine openings that were closed include adits, declines, shafts, daylighted stopes, and dugout dwellings. The desert locations permitted implementation of cost-effective closure techniques that relied upon the use of native materials. The strategies and techniques developed for these desert closures are adaptable to other climates.

Jan 1, 2002

By Tedd B. Bodimer

Why complicate an already complex machine such as a continuous miner by adding roof drills? Immediate permanent roof support is an immediate thought of the mining engineer just as elimination of frequent time-consuming places changes is a thought of the methods engineer. The realization of those two objectives has the potential for improved safety with increased production is the thought of the general manager. Miner-Bolters Used a Generation Ago These are not new thoughts as the 1CM continous miner equipped with two integral roof drills was introduced twenty-five years ago. Approximately two hundred of these machines were sold in the next five years for use in medium and high seam operations. The 1CM miner chassis that remained stationary in the center of an entry or room while the ripper bar was swung and sumped hydraulically provided an ideal platform for mounting two roof drills that could be operated during the continuous miner's production cycle. Two roof bolts could normally be installed in less time than required for the mining cycle. A typical roof drill unit is shown in Figure I.

Jan 1, 1981

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By Víctor Vázquez, Guillermo Tiburcio, Martin Encinas, Jesús L. Valenzuela, Erick Montaño, Alejandro Valenzuela, José Parga

Merrill-Crowe is the primary process used for the concentration and purification of silver in a cyanide solution. The Langmuir Adsorption model for silver recovery in a cyanide solution was used for the study. The maximum adsorption capacity was 6.19 mmol/g for silver. This model properly adjusts the experimental results of the adsorption equilibrium with high correlation coefficients, which also favors the formation of a single layer of molecules adsorbed for the silver in the electrocoagulation- generated species. The thermodynamic parameters ΔG, ΔH, and ΔS were estimated, and it was found that the adsorption process is exothermic and spontaneous. For the kinetic study, the Lagergren second-order equation was used to study the adsorption speed. To characterize the solids coming from the electrocoagulation, X-ray diffraction (XRD), and scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDX) were used; the results of this study suggest that silver is present in aluminite, hydroniumjarosite, and alunogen.

Oct 30, 2021

By Peter N. Yanker

The two types of dryers used in the drying of copper concentrates are the rotary dryer and the spray dryer. The rotary dryer has until recent history been the traditional drying method used, Although spray dryers have been used in the chemical field for many years it is only recently that they have been accepted for drying of copper concentrates. The comparison made here will apply in a narrower sense to the drying of copper concentrates as fed into the reverbatory furnaces of the Smelter. To compare a rotary dryer and a spray dryer, which are two totally different methods and pieces of equipment, it is best to view them as systems each made up of certain elements

Jan 1, 1976

By W. L. Price

The intelligent selection of wire cloth and perforated plate for screening surfaces seems a rather confusing subject to the newcomer in aggregate processing. The proper application of various screening surfaces is a complicated one and one could consider himself an expert only after many years of working with all applications. However, part of the subject matter could be simplified considerably for, the average screen user. In this paper an attempt will be made to do this, by presenting some comparative specification data along with cost figures Unfortunately, it is impossible in the limited scope of this paper to give actual service comparison records between different cloths or cloth and plate. Anyone who has considered making actual service comparisons for competing screening media is well aware of the almost insurmountable problems Their solution would form the basis for a separate paper on that subject alone. Therefore, this paper will be limited to comparative data up to the point of installation.

Jan 1, 1961

By Y. C. Lo

This paper presents the development of ultrasonic grinding technology for material and mineral processing. The principles underlying this new technology, as well as their implementation in two laboratory scale devices are described in detail. Ultrasonic grinding experiment results are discussed with respect to operating variables and the achieved product sizes. Special attention has been given to the electrical energy consumption of the grinder, and an attempt to compare its efficiency with tumbling mills has been made. A mechanical system capable of measuring the specific grinding energy is also described.

Jan 1, 1991

By Donald E. Zipperian

It has been recognized that froth flotation of mineral particles utilizing rising flow of micro size air bubbles, counter-current to quiescent falling flow of particles in a column type cell, provides a unique mechanical atmosphere conducive to extension of froth flotation process to much coarser and finer particles sizes than possible with mechanically agitated and aerated cells. 1,2,3,4. This paper describes metallurgical results obtained at several plant installations of large capacity commercial size Deister FLOTAIRE® Column Flotation Cells. These cells utilize air aspiration into surface tension lowered water to generate micro size bubbles. Operating costs, power, wear, and scaling characteristics of rougher, cleaner, and scavenger units are compared with mechanical units. Problems encountered and scale up criteria developed when increasing from 0.20m(8inch) diameter pilot cells to 2.42m(96inch) commercial cells are discussed.

Jan 1, 1985

By Suresh K. Bhatt

A mathematically simulated modeling technique is used in this U.S. Bureau of Mines paper to represent a hypothetical mining operation with existing mining technology and prevalent mining costs. Mining scenarios are prepared and evaluated for potential benefits and costs available through computer-assisted mining. Base criteria, parameters, and methodology are described.

Jan 1, 1991

By Felicia F. Peng

Using granular media for removal of soluble manganese from mine water and industry waste stream has the advantage of forming a compact surface layer of manganese oxide coating on the media. This process can avoid the step involving the separation of voluminous sludge of manganese hydroxide by the high-pH method for soluble manganese removal. The removal of soluble manganese is accomplished by adsorption and oxidation. The adsorption of Mn(II) on the manganese oxide-coated media was rapid through the specific adsorption and may be due to the ion exchange of hydroxyl ions on the manganese oxide by Mn(II). In the subsequent step, the adsorbed Mn(II) form the intermediate manganese complex on the manganese oxide product is oxidized with dissolved oxygen or other available oxidant source in the aqueous solution. This paper presents the efficiency of removal of soluble manganese from mine water by using a laboratory fluidized bed and the recovery of manganese oxide coating on the anthracite coal particles. In order to accelerate the formation of the manganese oxide layer on the surface of anthracite media, dilute potassium permanganate solution is used as an active oxidant. The effects of operation parameters on the manganese removal including pH, flow rate, concentration of feed and oxidant dosage are evaluated.

Jan 1, 1996

By C. L. Schneider

The calculation of the liberation spectrum in the product from continuous milling operations is a problem of considerable importance and is difficult to solve because the population balance equation must be integrated in two-dimensional space. Complete solutions require the estimation of a large number of parameters unless a structural model of the ore texture can be used. A very simplified textural model based on the use of the modified Andrews-Mika diagram and the PARGEN simulation of multi-phase particles has been formulated and is used to simulate the behavior of a continuously operating laboratory ball mill. A sensitivity analysis for this mill has been done to show the likely effect of model approximations on the predicted liberation spectrum which will be measured.

Jan 1, 1992

By Britta Schoesser, Zdenek Zizka, Markus Thewes

"The support pressure of a slurry shield corresponds to the in situ earth and groundwater pressure to ensure the stability of the tunnel face. The support fluid (bentonite suspension) penetrates from the excavation chamber into the pore space and transfers the support pressure to the granular structure of the soil within this zone. At the same time, the cutting tools rotate periodically with the cutting wheel and remove the penetrated soil up to a certain cutting depth at the face. Shortly after the tool passing, the penetration process starts again. Both, the support pressure and the soil excavation, act in the same direction at the tunnel face, but they are subject to different cyclic intervals. This relationship between the time needed for the transient penetration process and the interval of the cyclic passage of the cutting tools at a local point at the face is examined and the impact onto the global face stability is discussed. INTRODUCTION Slurry shields are usually deployed for excavations in soft ground. The main application range is in non-cohesive soils (DAUB Recommendations 2010). In non-cohesive granular soils, the tunnel face stability is one of the key design issues. The slurry shields make use of pressurized bentonite suspension (slurry) to support the unstable tunnel face. To support the tunnel face effectively, the slurry pressure has not only to counter the groundwater pressure, but also has to be transferred into an effective stress to support the soil grains. In general, the pressure transfer can be achieved in two ways: (1) with a thin flexible membrane or (2) a penetration zone. The membrane (1), called filter cake, creates a thin impermeable layer from bentonite particles directly on the tunnel face, and enables a transformation of excess slurry pressure into effective stress. In case of penetration zone formation (2), the excess slurry pressure is transferred onto the soil skeleton along the entire penetration depth by shear stresses between slurry and soil grains. These theories, presently applied to assess the pressure transfer on the grains within slurry shield tunnelling, are originating from diaphragm wall technology, e.g. Müller-Kirchenbauer (1977), Kilchert and Karstedt (1984). They assume that the support pressure transfer mechanism is built-up instantaneously on the whole tunnel face and is not damaged or influenced by the interaction with excavation tools. These assumptions are valid for conditions during the excavation of diaphragm wall trenches whose bottom is excavated and the walls of the trench are supported. At the tunnel face of a slurry shield, the support suspension acts on the same area as the soil excavation. Hence, the conditions on the tunnel face are transient (time dependent) due to the time period needed for the penetration process of the slurry and the periodical damage of the pressure transfer mechanism by excavation tools (Fig. 1a)."

Jan 1, 2016

By E. F. Draskovich

In 1984 a high temperature heat recuperation system was installed in the pellet plant of the National Steel Pellet Company located in Keewatin, Minnesota. The system is similar to those of Cleveland Cliffs Empire and U.S. Steel's Minntac operations. It recovers hot process air from the cooler by induced flow, and directs it to an intermediate zone between the drying and preheat zones on the grate machine. This system recently underwent further modifications in April 1985, following initial operation in 1984. The M. A. Hanna Company, which manages the property, developed the design criteria and made the subsequent recommendations for modification through its research facility in Nashwauk, Minnesota.

Jan 1, 1986

By J. P. Matoney

In recent years, the diminishing supply of natural gas has led energy suppliers and consumers to consider making synthetic natural gas from coal. A number of processes have been devised to produce gas from coal; many of these have been operated at the pilot stage and some have been operated commercially. Each process has specific coal feed stock requirements with respect to size consist and moisture content. The purpose of this presentation is to compare the estimated costs for coal handling, live storage, size reduction and drying facilities that would be required for delivery of coal feedstock to different gasification processes.

Jan 1, 1977

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain enough rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-exchanged elements associated with clays and chemically bonded elements within the organic coal matrix. Researchers at three universities have collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts have found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. On the other hand, leaching was effective in recovering REEs from coarse middlings materials collected from multiple coal basins as indicated by recovery values exceeding 80%. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. INTRODUCTION Recent studies initiated by NETL showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts [1]. According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region (WV, KY, PA, VA, AL, TN) with a capacity of 166,495 tons/hr or more than 1 billion tons annually [2]. If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry can become a significant producer of RE minerals as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the product cost. Other researchers have also shown that coal can be a significant source of REEs. The average sum of the rare earth plus yttrium (REY) concentration of the world coal is approximately 68.5 ppm, which is lower than the corresponding upper crustal concentration (UCC) (168.4 ppm). However, the average REY content of the mineral matter in the world (404 ppm) and U.S. coals (517 ppm) are 3 times higher than the average UCC. Some of the mineral matter in Russian and Chinese coals have REY concentrations in the range of 0.68 to 2.03% and contain a better source of higher value REYs than many primary rare earth deposits [3]."

Jan 1, 2017

By Martin H. Stanczyk

In recent, years the demand and consumption of finely ground industrial minerals has substantially increased for such uses as fillers and chemically reactive components. The size, specifications for these types of industrial mineral materials vary to a great extent and depend on the particular end purpose' and on the physical properties of the mineral itself. Size reduction of industrial minerals usually is obtained by conventional crushing and grinding methods. However, some specialized milling techniques have been developed for producing these minerals in extremely fine particle size ranges. During recent years the Bureau of Mines has been investigating an attrition grinding method to produce ultrafine subsieve-size mineral particles. The Bureau developed process, which has been patented,2 comprises the intense agitation of a slurry composed of the material to be ground, a relatively fine granular grinding medium, and a suspending fluid. The process has been shown to be effective for the comminution of kaolin in the particle size range of 2 microns and finer on a batch3 and continuous basis.4,5 This report presents the results of batch tests made to determine the effectiveness of the attrition grinding process for comminuting commercial products of (1) mica, a tough lamellar material, (2) fluorite, a brittle intermediately hard material, and (3) barite, a relatively soft, massive material.

Jan 1, 1967

By T. Skodack

This presentation will compare actual work site results for the loading and transport of shot rock for two major tunneling projects in North America. "SCARMAR" (the Canadian subsidiary of S & M Construction) is operating a rail bound Hagglund continuous gathering arm loader in combination with a Hagglund nine car shuttletrain system at the West End of Table Mountain on the B.C. Railway project near Tumbler Ridge, Canada. Al Johnson Construction is operating a Hagglund rubber tired continuous gathering arm loader in combination with haul trucks at the Rocky Mountain Pump Storage Project near Rome, GA. This paper will compare: 1) tunnel and ground conditions, 2) the total work cycle as it relates to mucking and haulage 3) efficiencies and related problems with the two systems 4) mucking and haulage rates 5) operating costs, and 6) recommendations for future large tunnel excavations. Manuscript not received in time for publication.

Jan 1, 1983

By William A. Rehrig

During recent years, there have been frequent investigations on the geochemistry of biotite. This work has emphasized, and no doubt was prompted by, factors related to mineral exploration, particularly for those deposits of the porphyry copper type. A large number of papers have been devoted to the obtainment of trace-element data from plutonic biotite. These data have been used to extract primary geochemical information pertaining to the parent magna and the hydro-thermal system which together give rise to porphyry copper deposits. In two early works, Putman and Burnham (1963) and Parry and Nackowski (1963) analyzed base metal contents of ferromagnesium minerals, primarily biotite, from various barrenfmineralized plutons of the Basin and Range Province. One similar conclusion from the two studies was that the Cu, Zn, and Pb contents of magmatic biotite served as indicators of ore development within the granitic rocks genetically related to ore. This theme was then pursued vigorously by a number of authors until the present time. Results, however, have been contradictory, as reviewed by Coope (1974). For example, studies by A1 Hashimi and Brownlow (1970), Lovering et a1 (1970), Putman (1972), and Graybeal (1973) continued to support positive primary relationships between the trace-metal content (usually copper) of biotite and associated sulfide mineralization. By studying biotite in close spatial association will sulfide occurrences, Putman (1972) and Graybeal (1973) developed models for base metal partitioning in magmatic systems based on their discovery of inversely distributed copper between silicate (biotite) and sulfide phases. Conversely, research by Bradshaw (1967) and Blaxland (1971) plus the recent findings of Parry and Jacobs (1975) and Kesler et a1 (1975) found little if any evidence to support a correlation of biotite base-metal or

Jan 1, 1976

By K. T. Valsaraj

The separation process called solvent sublation for the removal of two hydrophobic compounds (penta-and tri-chlorophenols) from the aqueous phase is discussed. A steady state mathematical model for the process is discussed. The process was conducted in a continuous countercurrent mode. The underlying mechanisms, theory and experimental details on the effects of process variables on removal efficiency are reported.

Jan 1, 1992

By B. R. Pothini, H. von Schonfeldt

In underground coal mining many excavated openings have a relatively short projected life span. To ensure safety for men and materials at a minimum cost over the projected operating life, only pillars for overburden support and roof bolts for support of the openings are used extensively. Mining activity constantly changes the geometry of the mine producing load changes on the structural support members of the openings that often induce unstable deformations which can lead to roof falls or pillar failures. The paper describes how simple deformation measurements can be used to design primary and supplementary roof supports and to predict roof falls and possibly pillar bumps. Specifically, bed separations in the roof measured directly with the help of borescopes and calculated from differential convergence data are used to optimize bolt links or support requirements for chemical stabilization of mine roofs. Roof falls are predicted on the basis of admissible values for cumulative convergence between roof and floor, convergence rate, and the change of the rate of convergence. The pillar extraction operations convergence anomalies detected from contouring identify bump prone pillars, while convergence and pillar dilation determine the yield zone in a pillar to verify pillar softening and de-stressing. Manuscript not received in time for publication.

Jan 1, 1983