Search Documents

By Dai Wang

Stoppings are necessary ventilation control devices for effective air distribution underground. However, one of the major problems underground mining has is that every stopping is a potential leaking source. Since air always flows from a point of high pressure to one of lower pressure, and the total pressure at every point in intake airways is higher than that in the return airways, air will always tend to leak from intake to return (Tien, 1996). In many mines, less than half of the air entering the mine actually gets to the working areas; the rest of it simply short-circuits directly to return airways through leaky stoppings instead (Timko and Thimons, 1983). Leakage through a stopping occurs because of pressure drops across the stopping and available leaky path in stoppings. Empirical equation has been widely used to characterize the relation the amount of leakage and variables that affect leakage. However the use of this equation requires accurate information for constants which are not always readily available. It is the attempt of this paper to derive an equation similar to the Atkinson Equation that can readily be applied to characterize pressure-leakage relationship for any given stopping.

Jan 1, 1998

By S. Shankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant. Therefore, as part of the Respirable Dust Center's ongoing research, a three part study was envisaged: study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; study of the same in the Lake Lynn Laboratory Mine of the USBM with both airflow and walking by personnel causing re-entrainment; and mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory Mine are presented. Further, the results from the wind tunnel studies are compared with the results from in-mine studies conducted at the Lake Lynn Laboratory Mine of the USBM. Comparing the results from the two studies it was observed that increasing air velocity increased the rate of re-entrainment, but increased time of exposure decreased the airborne dust concentration. Compared to same size particles, a mixture of sizes created more airborne dust concentration when re-entrained. It was also observed that contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1995

By Corby G. Anderson, Sheikh Abdul Rezan Sheikh Abdul Hamid, Sanjith Udayakumar, Ahmad Fauzi Mohd Noor, Teuku Andika Rama Putra

Chemical and mineralogical characterization of Malaysian monazite, a phosphate mineral, bearing rare earth elements separated from the tin tailings originated from Ipoh, Perak, Malaysia, was performed in this paper. The study aims to collect detailed information on the chemical composition, crystal phases, and microstructure of the mineral monazite concentrate that would aid to optimize the subsequent hydrometallurgical processes for high-efficient separation of thorium and other associated rare earth elements. A systematic characterization study of the concentrate was conducted using techniques such as optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and Fourier-transform infrared spectroscopy (FTIR). These techniques analyzed the morphological details on the surface, elemental analysis, and mineral association assessment and identified the surface functionalization groups. The bulk composition and the mineral phases in which the elements are present were studied by wavelength-dispersive X-ray fluorescence (WD-XRF) and X-ray diffraction (XRD) studies respectively. The XRF analysis confirmed the presence of Ce, La, Nd, Pr, and Y (rare earth oxides: REO’s ~ 60 wt.%) while thorium dioxide (ThO2) accounted for 7 wt.% of the total composition. Traces of Ca, K, Al, Fe, Ti, and Mn were also confirmed by SEM elemental mapping. The XRD results confirmed that the concentrate was primarily composed of monazite (Ce, La, Nd, Th (PO4)) along with minor impurity phases of quartz. Automated mineralogical analysis was used as a confirmatory tool to corroborate the preliminary evidences. Based on the particle size distribution analysis supported by SEM, the majority of monazite grains were found to be present in the size range of 170–210 μm. Strong bands of PO4 and SiO4 were observed in the IR spectra corresponding to the phospho-silicate matrix of the REE mineral.

By W. R. Bull

This paper examines water-only cyclone performance for the cleaning of fine coal, and the effects of changes in feed flow rate, feed pulp density, and vortex finder diameter. A model is presented for performance simulation which can be used to predict products obtained based on feed washability data.

Jan 1, 1987

By Stephen Meyer, Véronique Falmagne, Antti Pyy

Kittilä Mine is a gold mine located in Northern Finland, owned and operated by Agnico Eagle Finland. The mining operation started in 2008 with open pits which were completed in 2012 and production moved to being entirely underground. The mine consists of four separate orebodies, currently producing 2.0 Mt per annum, and requiring over 19 km of development on a yearly basis. The principal mining method is long hole stoping with delayed backfill. Microseismic monitoring was initially tested in the Suuri orebody, in the mining block between the 625 and 500 Levels. A small monitoring system was installed in 2018, after observations of stress-induced damage to the rock mass and in anticipation of future mining at greater depth. The initial goals were to evaluate if useful data could be recorded and test the signal quality of different sensor types. Prior to 2018, ground control related challenges in the Suuri and Roura mining blocks had been mostly related to sill pillar mining and block movements between weak graphitic schist planes. Seismic monitoring in the Suuri deposit proved successful for following the rock mass response to mining and helped support the rationale for early monitoring in the new, deeper mining block in Rimpi at 900 m depth. Preliminary geotechnical characterization and testing of the rock mass showed areas of silicification in the footwall rocks with potentially continuous structural features. Seismic monitoring of the Rimpi area has confirmed the brittle behavior of the rock mass, with strong seismic responses induced by stress changes following blasting being recorded. In addition to this expected behavior, a large magnitude event associated with significant damage in the footwall drive development 90 m above the stoping was experienced. Initial investigation of the rockburst showed two separate damage locations with over 300 tons of displaced rock. The seismic monitoring system recorded this rockburst as a single seismic event with magnitude significantly larger than previously recorded. Additional analyses indicated a possible thrust fault event, triggering two separate strainbursts. Following this event, the ground support system was upgraded in parts of the footwall drives to improve dynamic capacity. Systematic calculation of the source mechanisms for the small footwall events down to Mw-2.5 has revealed potential planar structures in the footwall. Early implementation of microseismic

Apr 26, 2022

By J. D. Vincent

The Mission By-Products Plant at the Mission Concentrator of the American Smelting and Refining Company, some 20 miles south of Tucson, Arizona in the Twin Buttes mining area, has been in operation slightly over a year. The plant produces a molybdenite concentrate a copper concentrate and, at times, a zinc concentrate. An intensive test program of over three years was conducted at Mission to make the recovery of molybdenum economic. Briefly it was found necessary to make a scavenger concentrate in the copper mill before it was possible to recover economic quantities of molybdenite. By so doing there were resulting additional recoveries of copper, silver and zinc. This program resulted in the design and construction of the existing plant. A paper by the authors discussing the test work and the design was presented at the, October 1965 meeting of the American Mining Congress in Las Vegas, Nevada, by Mr. Wayne Bossard.

Jan 1, 1966

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and galvanodynamic and chronopotentiometric techniques were used to characterize the effects of DXG-F7®, a commercial smoothing agent, on copper electrodeposition onto 316L stainless steel from a synthetic electrolyte containing 40 g/L copper (Cu2+), 160 g/L sulfuric acid (H2SO4) and 20 mg/L chloride (Cl-) at 40oC. The findings were compared against results using HydroStar® 4208, a modified polysaccharide. The nucleation overpotential and plating potential observed in cyclic voltammetry and galvanodynamic testing showed that neither DXG-F7 nor HydroStar significantly polarized acidic copper electrodeposition. Subtle differences between the additives were found during EIS testing and modeling, but more research will be needed to fully understand these differences. Surface-roughness measurements of two-hour deposits indicate that DXG-F7 and HydroStar produced smoother deposits as their concentrations in the electrolyte increased. No difference in the surface roughness of deposits was detected between the additives. Based on the experimental evidence resulting from the laboratory testing, no significant difference was found between DXG-F7 and HydroStar at 20 mg/L Cl- concentration, with the exception that DXG-F7 dissolves more easily in water than HydroStar. Introduction Cathode deposits obtained from acidified copper sulfate electrolyte(s) without organic additives are often soft, coarsely crystalline and nodular (Sun and O’Keefe, 1992). Therefore, small amounts of organic additives are added to the electrolyte to produce level and dense cathodes during copper electrowinning. The action of organic additives is thought to be due to their adsorption on the surfaces of the newly formed copper grains. Hence, any copper grain that grows excessively fast adsorbs a layer of organic additive, which inhibits growth. The result is a smoother and harder deposit of suitable purity (Sun and O’Keefe, 1992). In part I of our four-part series on the examining of copper electrowinning smoothing agents, a review of previously published work on organic additives used during copper electrowinning was presented (Moats, Luyima and Cui, 2016). In the review, it was noted that many tankhouses had switched from guar to other saccharide-based products such as HydroStar and DXG-F7."

Jan 1, 2016

By James S. Goff, Stephen J. Navin, Wesley W. Moulton

The White River Shale Oil Corporation (WRSOC), as agent for Phillips Petroleum Company, Sohio Shale Oil Company, and Sun Shale Oil Company, is developing a prototype oil shale facility on Federal Lease Tracts Ua and Ub, located in northeastern Utah and known as the White River Shale Project (WRSP). The Ralph M. Parsons Company (Parsons) has been retained as the design engineer/constructor for the project. This paper covers the successful pregrouting of the Bird's Nest Aquifer in conjunction with the sinking of a 9.2-m (30-ft)-diameter shaft and driving of a 3.89-m by 5.64-m (18.5-ft by 12.75-ft) decline. The Bird's Nest Aquifer derives its name from the ellipsidal solution cavities caused by leaching of random-size nacholite nodules. The sodium bicarbonate nodules occur as persistent bands within a matrix of siltstone and marlstone. The team, made up of the owner, engineer/contractor, and subcontractor successfully grouted the shaft down to an inflow of less than 0.06 lps (1 gmp) and the decline down to less than 0.12 lps (2 gpm) by injecting a total of 213.190 kg (470,000 lb) of Celtite Terraseal, 113,400 kg (250,000 lb) of limestone dust, and 41,730 kg (92,000 lb) of cement into the formation.

Jan 1, 1985

In this paper, response surface methodology was applied to optimize the experimental conditions for the wet grinding of synthetic rutile. The effects of parameters such as rotation speed, solids concentration and duration of grinding on grinding efficiency were systematically investigated and the process conditions were optimized, using a nonlinear regression model based on central composite design. The statistical analysis of the results showed that in the range studied, the grinding efficiency of synthetic rutile was significantly affected by the rotation speed of the conical ball mill. According to results from analysis of variance, the value of the determination coefficient (R2=0.9989) indicates that the predicted values are found to be in good agreement with experimental values. The optimized experimental conditions were as follows: a rotation speed of 350 rpm, a solids concentration of 27.31% and a grinding time of 50.31 min, respectively. Under optimum conditions, the predicted grinding efficiency of 94.79% is obtained. The experimental values from the validation experiments were well within the predicted value of the model.

Jan 1, 2011

By S. Tandanand

The Bureau of Mines, U.S. Department of the Interior, assessed the geological effects on the ratio of maximum subsidence and extraction thickness, hown as the subsidence factor, to develop a simple method for predicting the maximum subsidence. The study is restricted to the Northern Appalachian Coal basin where data were collected from 13 coal mines. A model previously developed to relate the subsidence factor with the lithology and with the width and depth of working panels was used in the assessment. The result shows the possibility of determining maximum subsidence without resorting to a rigorous method.

Jan 1, 1982

By C. D. Elifrits

The required reclamation of land disturbed by surface coal mining often results in the creation of some over steepened slopes which are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has indicated that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations will be summarized in this paper and field results shown.

Jan 1, 1986

By Mark Leggett, Kevin Roberts

The need to modernise and increase the safety provision of older road tunnels raises challenges in maintaining the operation of the tunnel during such improvement works. The Mersey Kingsway twin road tunnels located in Liverpool UK, constructed in the late 1960s, have had three new cross passages constructed to allow emergency evacuation from one tunnel to the other tunnel and provide safer access for emergency services. The 3200m long road tunnels are lined with an unusual reinforced concrete steel-faced segmental lining with a paint finish. Construction of the cross passages occurred during night possessions with the tunnels returned to normal operation during the daytime. Constructed through water bearing sandstone and lined with precast concrete segments, the passages required advance ground treatment and support works. This paper presents the historical background to the Mersey Tunnels and describes the procurement strategy, design and construction approach adopted for these important safety improvements.

Jan 1, 2003

By K. Rajamani

The word adapt means "to change so that one's behavior will conform to new or changed circumstances." Applying this definition to process controllers suggests that an adaptive controller can change its behavior in response to changes in the dynamics and disturbances of the process. In the minerals industry there are many control cases where adaptive control will provide superior control as compared with more traditional PID (proportional, integral, derivative) control. A typical plant uses as many as 100 to 200 control loops for lprocess regulation. Therefore, the task of initially tuning and then periodically retuning these controllers is a formidable problem, During the time the controllers are "un-tuned", product quality may deteriorate and unstable operations may result. Adaptive controllers are capable of tuning themselves, thus avoiding this problem. The computers commonly used in distributed control systems are easily capable of implementing adaptive controllers. In addition to the possibility of using the control computer to implement adaptive controllers, many distributed control systems will offer adaptive control as a standard feature in the near future.

Jan 1, 1984

By C. A. Holley

The generation of coal fines is a growing problem which has serious environmental and resource recovery Impact. Several methods of agglomeration are studied including the production of briquettes for the consumer market. Simplified process flow diagrams, "order of magnitude" plant capital cost and operating costs are presented.

Jan 1, 1986

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

By K. T. Brashear, N. Ripepi

"Over recent years, specifically following the MINER Act of 2006, an increasing number of manufacturers of underground mine seals in the United States have begun using a form of pumpable cement or shotcrete to create barriers separating the working and abandoned sections of underground coal mines. This seal material, while generally considered to be homogenous and solid, contains a network of microcracks, voids, and delaminations. Generally, it has been assumed that methane (CF4) leakage around these seals is a result of movement around the boundary interface between the seal and surrounding strata. Using a perfluorinated tracer compound, perfluoromethyl-cyclohexane (PMCH), the movement of gases can be monitored through seal material to observe how gases move though the material, both intact and with faulting in the material. This paper documents two large experiments where the movement of PMCH was monitored in the field, along with modeling confirmation using 3D visualization software. INTRODUCTION According to a report in 2007, there were over 14,000 active mine seals in underground U.S. coal mines alone (Zipf, Sapko, & Brune, 2007). These seals are used for both ventilation and safety purposes, to direct the flow of air away from the abandoned area of the mine and to help eliminate the propagation of explosions that can occur on the outby side of the mine seal. The atmosphere on the outby side of these seals typical consists of low levels of methane that have the potential of producing leakage along the face of the seal on the inby side. Methane leakage around mine seals has historically been attributed to the permeability between the seal and mine interface (McPherson, 1993). According to the United States Bureau of Labor Statistics (BLS) between 2003 and 2012 an average of 17 deaths occurred annually in underground bituminous coals mines. The only time during the ten-year period where the fatalities were higher than the average was in 2006 and 2010, years which had three major explosions occurring in underground coal mines in West Virginia and Kentucky. Two of the explosions were propagated through the mine by seal failure or methane leakage around newly poured seals (Light, et al., 2007) (Gates, et al., 2006). These recent events, and new regulations regarding seal strength (MINER Act), have created a need to monitor the condition of underground mine seals. BACKGROUND Measuring the permeability of solid materials, such as concrete or seal materials, can be a valuable tool in the field of non-destructible testing (NDT). By using an inert gas, such as nitrogen, injecting the gas into a solid structure, and measuring the resultant flow rate and pressure differential, this can provide valuable information about the structure. Studies have shown permeability can be affected by the stresses applied to the structure, as well as temperature and moisture (Choinska, Khelidj, Chatzigeorgious, & Pijaudier-Cabot, 2007) (Abbas, Carcasses, & Olliver, 1999)."

Jan 1, 2015

By P. R. Taylor

A reaction is evaluated by which heated and pressurized water is used to precipitate metal oxides from loaded Kelex 100 complexes. Pure copper oxide (CuO) and pure nickel (Nio) in powder form, and ranging in average size from 12 to 25 micrometers, were found to precipitate from copper and nickel loaded Kelex 100/kerosene complexes, by water heated and pressurized to between 374 and 400 °c and 2170 psig (148 atm) and 3500 psig (238 atm). The precipitation is suggested to result from hydrolysis of the metal, following exchange for the hydrogen in the phenolic hydroxyl of the Kelex 100 structure, enhanced by the conditions provided by heated and pressurized water. The reaction is believed to have the characteristics of homogeneous nucleation and heterogeneous growth. The effects of temperature, pressure, initial metal concentration and seed addition on the kinetics of the process were studied. In addition, characterization studies were performed on the reaction products. A detailed discussion of the experimental results is presented.

Jan 1, 1992

By M. K. Boateng, K. Awuah-Offei

"Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. The results show that the model is much more sensitive to the probability of imitation than the other two parameters. Thus, to reduce uncertainty surrounding the model’s predictions of community acceptance of mining, mines need to obtain accurate estimates of the probability of imitation. INTRODUCTION Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. AGENT-BASED MODEL OF COMMUNITY ACCEPTANCE A few researchers have started using agent-based models to study mining systems (Fujiono 2011; Nakagawa et al. 2013; Bahr 2015; Boateng and Awuah-Offei 2017a, b). Nakagawa and co-workers used ABM to evaluate dynamics of a mining project’s stakeholder networks whereas Fujiono used ABM to study innovation diffusion in the mining industry. Our previous work has presented models and a framework for modeling information diffusion in a mining community and its impact on level of acceptance (a measure of SLO) of the mining project (Boateng and Awuah-Offei 2017a, b)."

Jan 1, 2018

By J. F. T. Agapito

Two flat-lying trona seams 3-to 3.5-m thick, approximately 10 m apart, and at depths of 250 m are mined by room-and-pillar at OCI's Big Island Mine in Wyoming. Continuous miners and a yielding pillar system have contributed to improvements in resource recovery and productivity. Long-term stability with minimal subsidence is needed for a large portion of the mine beneath the Green River channel. This was investigated by computer modeling in 1990. Although results of the study indicated good long-term stability, recommendations were made for stress determinations to verify the model. Stress determinations made in 1997 showed pillar stresses 10% to 20% higher than the model stresses, and barrier pillar stresses 10% to 15% lower. This implies that higher panel stresses will be transmitted from the upper to the lower seam. A stability evaluation of the lower seam is planned before two-seam mining to assess entry widths and support requirements.

Jan 1, 1999

By Michael J. Beus

This paper describes research conducted under the BuMines's Advancing Metal and Nonmetal Mining Technology Program, a major element being the application of new and improved technology to shaft design in deep underground vein-type mines. Two basic design parameters considered in shaft planning are configuration (shape) and ground support. The most common shapes are circular and rectangular. Ground support systems include concrete, timber sets, steel sets, rock bolts, and steel liners. The inherent advantages and/or disadvantages of various shaft designs such as ventilation and fire resistance, flexibility and ground support characteristics are well known. Circular concrete-lined shafts have minimal resistance to air flora and are virtually fireproof, an important consideration in deep hot mines. However, concrete does not yield significantly, and failure conditions and misalignment cannot be easily repaired. Timber-supported rectangular shafts predominate in the Coons d'Alene Mining District with its highly stressed and frequently heavy ground. The sets can be relieved and reblocked when out of alignment. However, the constant maintenance and repair requirements result in exposure to an inherently dangerous working environment combined with excessive operating costs. Obviously a dilemma exists--a circular, concrete-lined opening has many desirable features, provided it is strong enough to withstand the stresses involved. Rectangular, timber supported shafts have proven adequate in the Coeur d'Alenes; however, the implication of increased maintenance and repair requirements on ever-deepening shafts in this district and other similar areas will be an important design consideration in the future. This paper, then, presents shaft-configuration and ground-support guidelines to help remove some of the uncertainty concerning the stresses to be encountered in typical deep vein mining areas.

Jan 1, 1976