Search Documents

By R. M. Schuster

This study attempts to compare the costs of transporting coarse coal by pipeline, versus the more conventional use of belt conveyors. Hydraulic conveying of crushed (not pulverized) coal has not had widespread commercial acceptance. However, there is little doubt that the technology is available, so that, should this method be proven economical for a given application, implementation of this technology will become more acceptable. Hydraulic transport by pipeline between the mine stockpile and the coal preparation plant, for distances normally considered practical for an overland belt conveyor, should be an ideal application. In this application there is no need for dewatering facilities at the receiving end of the pipeline, because, the receiving screens at the plant serve this purpose. Further, clarified water from the preparation plant can be recirculated back to the mine, a plus for water resource and environmental considerations.

Jan 1, 1982

By R. Woods, J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher.

Jan 1, 1976

The Yanacocha Project is the first foreign investment in Peruvian mining since Cuajone (1976). Three years after the project began, it has become the largest producer of gold from heap leach operations in the world and the top producer in Latin America. The success of Minera Yanacocha (MYSA) opens a new chapter in Peruvian mining with the exploitation of its widely spread gold deposits and has attracted the interest of foreign investors in Peru's ample mineral resources. Construction began on August 1, 1992 and after twelve months of arduous work, the first gold bar was poured on August 7, 1993 from ore from the Carachugo mine. In 1993, Minera Yanacocha produced 81,000 ounces of gold and 304,000 ounces in 1994 (40% above budget). Production is expected to exceed 500,000 ounces in 1995 with the start-up of operations in the Maqui Maqui mine. This paper presents a summary of MYSA's experiences during its first two years of operations in the areas of mining, ore processing, environmental protection, loss control and community assistance. The paper also shows that MYSA's successes are not only due to the richness of the deposit, but also to the combination of a number of factors basic to the project's success, such as: an economic policy favoring investment in Peru, the availability of highly qualified local personnel to facilitate the transfer of technology from the United States and the desire and determination of the partners to carry the project forward in an initial atmosphere of uncertainty and terrorism.

Jan 1, 1996

By Ronald F. Ayers

The study upon which this paper is based was completed by Battelle's Columbus Laboratories for the U.S. Army Corps of Engineers in 1974. It is but part of an overall effort by the Corps to evaluate the costs and benefits to the nation of waterway improvements. This study is primarily concerned with future coal markets for production from those counties near the Wabash River in the heart of the Eastern Interior Province. An objective here is to consider a most pessimistic energy (and hence, coal) demand for planning purposes.

Jan 1, 1976

By James Wm. White

Computer based dispatching in open pit truck haulage operations yields many benefits of current interest to mine management. The key tangible benefit is a substantial productivity increase with a given fleet of equipment or, alternately, a significant reduction in equipment required to meet production quotas. Other tangible benefits, depending on the operation, include minimizing rehandle, meeting several blending constraints simultaneously and ensuring a target plant feed rate. Intangible benefits include production forecasting, performance comparisons of trucks or shovels of different manufacture and extensive on-line report generation. Recent advances in mini and micro computer hardware and software and solid state electronics permit design and implementation of system features not feasible even a few years ago. Here we discuss many of these recent developments with emphasis on system aspects and dispatching algorithms.

Jan 1, 1983

By J. F. Abel, R. J. Spengler

Convergence measurement across the 17.4-m (57-ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 x 9.6 m (38 x 31.5 ft) inside diameter. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2.75 in.), and 5.7 cm (2.25 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1987

By R. J. Hickson

The Grasberg copper-gold deposit was discovered in Spring 1988, just one year prior to the planned closure of Freeport Indonesia's original Ertsberg open pit copper mine. In spite of Grasberg's remote location, 600m above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought their latest open pit mine into production in the last week of 1989, less than two years after discovery. This paper describes the start-up of the operation, highlighting synergies drawn from both the original Ertsberg experiences and the current Freeport Indonesia underground mines.

Jan 1, 1991

By M. Rieber

The potential for the wide-spread commercialization of superconductivity, the disappearance of all resistance to a direct current (D.C.) electric flow, began in 1986-87 with the development by Bednorz and Muller at IBM's Zurich Laboratory of an yttrium -barium -copper oxide conductor which attained zero resistance at 90t:. Although the status of superconductivity is still pre-bench scale, it is useful to forecast its probable effects on the copper industry. I t should not be forgotten that at their inception, the impacts of transistors, semi-conductors, thin films and fiber optics on the electric/electronics sector of this industry, were largely underestimated. Superconductors are not metals, but a class of ceramics. They represent an efficiency increase of one or more orders of magnitude. If their development is to be a boon to the copper industry, rather than a reduction of metal demand through miniaturization or material substitution, vastly expanded copper containing electrical uses must be in prospect. In this paper the projected uses of high temperature superconductivity are examined, followed by the remaining problems to be overcome. Assuming success, a time horizon for maturation is estimated. The penalties for the non-recognition of new markets and material substitution are shown on the basis of past forecasts. Finally, the application of successful superconductivity to the copper industry over the forecast period is estimated.

Jan 1, 1990

Coal waste materials inhibit direct vegetation establishment due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss # I coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980&apos;s with little topsoil resource available for final closure. The refuse was acidic (Total-S = .. 38%; pH = 3.6), black, high (70%) in coarse fragments, and had a low water holding capacity (4.5% in < 2.0 mm fraction). A small plot experiment was established on the refuse pile to evaluate the influence of liming rates (50% and 100% of lime req.) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from < 4.0 to > 6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Application of 27 Mg ha-1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity in leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile, so long term water treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 1999

By Nicholas Chlumecky

A practical method is described for determining or checking whether underground supports such as props, posts and mechanized longwall supports have bearing areas of proper size in relation to the type of ground or floor strata on which they are standing, It is felt that this information provides an approach to eliminate, as much as possible, a potential grave source of error during the selection of roof supports. This would also affect the choice of costly mechanized longwall equipment where it is possible that the size of the bearing area is not as carefully determined as, for instance, the design strength of structural components.

Jan 1, 1967

By H. Shafick Hanna

The beneficiation characteristics of low grade Birmingham red iron ores of the Big Seam and Ferruginous Sandstone seams were investigated using flotation and magnetic separation after reduction roasting. Samples of Bib Seam Ore responded more readily to concentration than the Ferruginous Sandstone ores. The impurities inherent with the iron oxide minerals limit the grade of concentrates recoverable from these ores to a maximum of about 61% Fe if reasonable iron recoveries are sought. Flotation concentrates assaying 60-61% Fe and about 0.1% P with attendant iron recoveries of about 63% were achieved from Big Seam ore charges while those obtained from the low phosphorus Ferruginous Sandstone samples analyzed 54-56% Fe. Reductive roasting and magnetic separation of ground charges of the two ore samples yielded concentrates assaying 60-61% Fe. Iron recoveries were better than those achieved by flotation, but the magnetic products of Big Seam ore were high in phosphorus (0.2-0.3% P).

Jan 1, 1983

By JA Vallejos

High stress underground mining poses a significant challenge to rock mechanics and rock engineering. To overcome theses challenges significative improvements in solutions and best practices of the design and operation of mines under high stress have been developed and implemented. This paper presents certain topics related to the management of high stress for sustainable underground mining. The topics include; the effect of preconditioning techniques (destress blasting and hydraulic fracturing) in the seismic rock mass response to underground mining and the dynamic behaviour of rock support systems. The opportunities associated with research in rock mechanics and practical rock engineering are discussed.

Apr 26, 2022

By Haydn H. Murray

The area from Ohio on the east, Tennessee on the south, and Minnesota on the west: contains some very unique and useful clay deposits. Included are fireclays and plastic clays in Ohio, Kentucky, Indiana, Illinois, and Missouri; flint clays in Kentucky and Missouri; ball clays in Kentuckv and Tennessee; adsorbent clays (fuller&apos;s earth) in Missouri, southern Illinois, and Tennessee; and alluvial clays and shales for structural clay products from every state. Unique kaolin clays are known in Minnesota, Missouri, and southern Illinois and halloy-site localities are known in southern Indiana. The geology, physical properties, and uses or potential uses of these midwestern clays are described.

Jan 1, 1980

By R. S. Olsen

Intensely altered rock has had a large effect on slope stability as slopes increase in height at Island Copper mine. Traditionally used, fracture-controlled rock slope stability design techniques have been supplemented with analyses of failure modes which include failure along curved surfaces typical of soil materials. A rock mass rating (Pa) system has been developed that addresses the lower end of rock mass strengths. Rock masses are rated in terms of fabric integrity, alteration, fracturing intensity and gouge strength. Rock mass classes have been defined using statistical frequency distributions of rock mass rating values. Strength values have been assigned to the various classes from shear testing, back analyses of failures and engineering judgment.

Jan 1, 1987

By M. Gunter, M. Buzon

"Talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic, and lacking in amphiboles. In southwest Montana, talc formed from hydrothermally altered dolomitic marbles, and is still actively mined. These talc deposits are typically in contact with quartzofeldspathic gneiss and marble. Accessory minerals vary between these rocks and the ore producing body; the identification and characterization of such minerals requires carefully selected analytical methods. Recent litigation and ensuing confusion over the petrology and asbestos content of these deposits challenges the talc mining industry in Montana, and elsewhere in the world. INTRODUCTION Commercial talc has been mined from the deposits in southwest Montana since the 1940s, and by 1956 the region had output 200,000 tons of talc ore (Chidester et al., 1964). Commercial talc refers to rocks containing more than 20% of the mineral talc (McCarthy et al., 2006); the ores from Montana typically contain upwards of 90% talc. This region remains the leading domestic source of talc in the U.S. partly due to the reserves in the area, and partly due to the diagnostic purity of the ore compared to that of other regions, some of which are no longer actively mined. The mineral talc, a sheet silicate, is expressed by the formula Mg3Si4O10(OH)2, and therefore can form in geologic environments that are rich in Mg, Si, O and water. The protolith for the talc deposits in southwest Montana is a dolomitic marble, but other common protoliths include ultramafic igneous, mafic igneous, and siliceous dolomites (McCarthy et al., 2006). Physical properties such as hardness of 1 on Mohs hardness scale, white streak and slippery feel are among some of the reasons why talc is so widely used as fillers in a number of industries. In decreasing order, ceramics, paper, paint, roofing, plastics, rubber, and cosmetics are the leading domestic industries that use talc despite the decreasing trend in U.S. talc use and production since 1994 (Virta, 2015). The purpose of this paper is to describe the mechanism of talc formation in southwest Montana by focusing on talc deposits and surrounding rocks in the Ruby, Greenhorn, and the Gravelly Ranges, and to relate the mechanism of formation to the composition of talc ores. The compositional data show mineral content of selected ores, and the major and trace element content of those minerals, specifically talc. Our electron microprobe (EPMA), powder x-ray diffraction (XRD) and x-ray fluorescence data for samples from five mines in these three ranges provide continued evidence of the purity of these ores despite claims made during recent litigation that these ores contain asbestos. The five mines that we discuss include the Beaverhead, Treasure, Regal, Willow Creek, and Yellowstone Mines (Figure 1.)"

Jan 1, 2016

By L. B. Hales

December 3, 1972, James Wm. White presented the results of an instrumentation and process control survey which was sponsored by the Anaconda Company at the annual Tucson Subsection AIME meeting.(1) Twenty-six responses were obtained from questionnaires sent to 48 operating plants throughout the world. The survey results were discouraging in that there were more failures and problems than examples of success. The following quotes are taken from the text of the paper. "We run our mill by the seat of our pants." &apos;If these blue sky Ph.D.&apos;s (in the instruments and controls area within research) had some operating experience they wouldn&apos;t make a lot of the suggestions they do."

Jan 1, 1981

By John Dodd

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrosion rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in commercial mills represents less than 10% of the total loss expressed as micrometers/hour of exposure in recent USBM tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills which indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and for cast irons, M7C3 carbides produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1984

By Alain A. Sonntag

The MBS Solvent Extraction System utilises a unique design of mixer- settler having very high capacity per unit area and great flexibility. The development of the mixer-settler is traced through its various stages wherein the independence of mixing and pumping, reduction in settler area requirements and simplicity of plant layout were achieved. The laboratory, pilot plant and full scale tests contributing to the development of the machine are described. The existing KREBS SX plants in Europe and Africa are described as well as the plants presently under design. Results of recent testwork are also given.

Jan 1, 1981

By R. T. Richins

Coeur d&apos;Alene Mines Corporation (CDE) is a precious metals mining company. The company&apos;s three mining operations are located In Nevada and Idaho. Collectively, these mines (Rochester in Nevada, and the Galena and Coeur In Idaho) produced about 61,000 ounces of gold and more than 7.5 million ounces of silver in 1991. The company is currently planning the development of two major properties; the Fachinal gold-silver project in Chile and the Kensington gold project near Juneau, Alaska. Fachinal and Kensington hold encouraging potential to significantly expand CDE&apos;s gold production during this decade. The permitting process for these two distinctly contrasting environmental settings, project design requirements and regulatory/political circumstances provide the basis for a comparative analysis of licensing and permitting requirements, timeliness of the permitting process and costs in the U.S. and Chile.

Jan 1, 1993

By D. J. Turk

Faced with decreasing production from the gold heap leach operation, Robinson implemented a drilling and blasting program on the leach pads in 1993. This program offset some of the negative effects of low ore permeability and short circuiting of leach solution that resulted in lower than optimum recoveries. The drilling and blasting program created new solution flow paths and increased gold recovery. Production and pulp assays at depth intervals, prior to and following drilling and blasting, reveal the degree of short circuiting and benefits of the program.

Jan 1, 1995