Search Documents

By E. H. Cho

A current environmental concern is the cleanup and restoration of soil contaminated with low-level radionuclides at DOE sites including the Nevada Test Site. At the present, there is no applicable process to economically and effectively deal with the remediation of contaminated soils. This situation requires development of a selective flotation process to separate the radionuclides from contaminated soil efficiently and economically. In this study, a minus 200 mesh size fraction of pure cerium dioxide was used as a surrogate for plutonium oxide which is the major contaminant at the Nevada Test Site. A Hallimond flotation cell was utilized to examine the flotation behavior of cerium dioxide with oleic acid under various conditions of pH and collector concentration Mechanical cell tests were conducted to float the surrogate from a mixture with uncontaminated Nevada Test Site soil in the absence and presence of calcium carbonate as a carrier. Two different sizes of the carrier (minus 150 mesh and 65-150 mesh) were tested. It was found through the Hallimond cell flotation tests that the cerium dioxide could be floated well at pH's 4 and 9 with 10-3 molar oleic acid. It was also found that the addition of the carrier drastically enhanced the flotation recovery of cerium dioxide. The flotation recovery of the surrogate increased from 34 % to 65 % by adding only 0.5 % calcium carbonate (minus 150 mesh) in the feed and also increased to 95 % by adding 10 % of this carrier to the feed. The finer size fraction of calcium carbonate (minus 150 mesh) was more effective in recovering cerium dioxide than the coarser size fraction (65-150 mesh) The flotation method utilizing a carrier of calcium carbonate seems to provide a high potential to be used for the remediation of soil contaminated with radionuclides at various Department of Energy's nuclear weapon sites.

Jan 1, 1996

By R. Pazhianur

Cathodic Protection using impressed current was employed to reduce the wear of the mill wall during ball mill grinding. Wear rates were determined from weight-loss measurements made on four, I-inch diameter, mild steel coupons installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH values of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 40-60010. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It is also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1996

By D. F. Lillie

The milling plant of Bicroft Uranium Mines Limited has been in operation for a period of 2 years. During this time many changes, both physical and chemical, have been made in an effort to improve plant efficiency. Investigational work has been facilitated greatly by the fact that the Bicroft mill consists to a large extent of two parallel circuits; however, the number of inter-related variables is great, and it is difficult to measure, let alone control, all of them simultaneously. The Bicroft mill staff feel that much progress has been made, but there is much yet to be done and many questions still to be answered. The property of Bicroft Uranium Mines is located in Cardiff Township in the Highlands of Haliburton County, southeastern Ontario, some 140 miles northeast of the city of Toronto and 70 miles due north of Lake Ontario. The ore-bearing dikes are classed as mafic, non-segregated, syenite and granite pegmatites. Microline, microline perthite, quartz, uraninite, uranotharite, fluorite, titanite, cyrolite, calcite, pyrite, pyrrhotite and molybdenite as important accessories. The mill was designed for a nominal capacity of 1,000 tpd with all sections except grinding, leaching and clarification capable of 1,500 tons. Feed was entered to one mill unit on October 29, 1956 and to the second parallel line on November 13. The total feed rate was at 1,000 tpd on November 15. The first precipitate was produced on November 12. By August 1958 the average entry had been increased to 1,410 tpd without the installation of any additional major equipment. The overall recovery has been greater than 93,0 pet do several months, but a recovery of 92.5 pct appears to be most economical. Operating time for 8 months in 1958 has been 97.1 pet although all grinding mills were relined during this period.

Jan 1, 1959

By Emily Wortman-Wunder

As the 2009 president of the Society for Mining, Metallurgy, and Exploration, Inc., I am pleased to present the 2009 issue of Transactions of the Society for Mining, Metallurgy, and Exploration, Vol. 326. A significant portion of the contribution that we as a society make is the publication of professional and technical papers that contribute to the advancement of scientific knowledge and information transfer. Communication within the mining community is the key to a successful society. Through the information-transfer mechanisms of books, magazines, meetings and electronic media, the technology exchange that is fundamental to the existence of the Society is accomplished. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, Pennsylvania, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume certainly satisfies that intent. In keeping with SME’s tradition of promoting technological developments while honoring the past, the 2009 Transactions represents an important milestone. It is the last Transactions to appear as a bound volume. Future volumes will appear as e-books only, with some of the Transactions-only papers appearing online prior to the ebook (exactly what form the new Transactions will take is still in development). The decision to go to an all-digital format for this longstanding publication was a difficult one, but one which we hope will better serve the mining community, especially our international members. This 2009 Transactions of SME, Vol. 326, contains a total of 73 technical papers (510 pages), including all 23 papers (136 pages) that were published in 2009 in the Technical Papers Section of Mining Engineering magazine (Vol. 61) and all 32 papers (232 pages) that were published in 2009 in Minerals & Metallurgical Processing (Vol. 26). In addition, this volume contains 18 papers (142 pages) that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All 73 technical papers were peer-reviewed and approved. The process of review and publication requires much hard work by authors, reviewers and publications staff. As the 2009 president of SME and on behalf of our members, I would like to extend our gratitude to all whose efforts contributed to the publication of this volume.

Jan 1, 2009

By B. Petri, N. Rouse

"Air overpressure monitoring procedures and instrumentation guidelines which apply to production blasting in underground limestone mining are not readily available. The industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground limestone mines. As such, there was no available background data from which the expected overpressure levels from production blasting in a new underground limestone mine could be predicted. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting in nearby production headings. To ensure the structures could withstand the blast-induced overpressure, a study was conducted to record empirical overpressure data and develop a model which could be used to control air overpressure levels by the production crews. This document describes the procedures used to develop the model, the development of the model, and the applicability of the model for predicting underground blast overpressures. INTRODUCTION A developing underground limestone mining operation required that a ventilation wall be built to house the permanent mine fans. At the time of the study, the mine was a single-level room and pillar operation with a 7.9 meter (26 ft) high roof, 13.7 meter (45 ft) wide entries, and 13.7 meter by 13.7 meter (45 ft by 45 ft) pillar dimensions. The mine is accessed via a 396 meter (1300 ft) long decline and 100 meter (330 ft) deep ventilation shaft. The ventilation wall was to be partially constructed of autoclaved aerated concrete blocks, for which dynamic strength data from explosives loading were unavailable. The company ownership feared that airblast may affect the wall due to the close proximity of the working faces. Therefore, the company management asked that the overpressure levels be estimated and compared with the designed wall strength. Few studies that apply to explosively-driven air overpressure levels in underground production blasting were found through a literature review. Therefore, the logical approach to assess the overpressure levels was to monitor the blast pressures at the site and conduct a thorough evaluation of the data. As a result of this study, the equipment setup and monitoring procedure used to record the airblast data is described. Finally, the experimental data gathered during the monitoring program is presented, trends and findings from the data are discussed, and recommendations for further study are presented."

Jan 1, 2015

By Gary Peach, Khalid Saif Al-Khayareen, Vigil Fernandez, Furqan Hameed

The Musaimeer pump station and outfall project (MPSO) is in Doha Qatar. This technical paper will discuss and explain the three major stages of geotechnical investigation employed. Stage one the tender geotechnical data and how this was used to design the TBM and identify various areas of risk. Stage two was the selection of supplementary geotechnical investigation methodologies. Stage three was the geotechnical investigation by specialist equipment installed on the TBM and providing further data on a real time basis as the TBM was advancing. Analysis of all the data will be provided along with the lessons learned.

Jun 23, 2024

By P. K. Sollars, M. A. Alspaugh

In May of 1996, Twentymile Coal Co. began Longwall mining in the Foidel Creek Mine's East Mine District. These Longwall panels are some of the longest in the world (5.48 km/18,000 ft) with very difficult and challenging geometry. The conveyance system is 1,800 mm (72 in) wide, has a 4,500 mtph (5,000 stph) capacity and employs multiple tripper drives. The trippers include traditional powering designs as well as unique regeneration and braking designs. Several components were developed specifically for this application including a mobile tail brake. Control algorithms were carefully developed and tested via computer modeling. A world production record was achieved in the third month of operation and over 1 million tons were mined in June 1997.

Jan 1, 1998

By C. RAMADINI, F. NURJAMAN, A. SHOFI, B. SUHARNO

In this work, the selective reduction of lateritic nickel ore was carried out using sodium sulfate, sodium carbonate, and sodium chloride as additives. The 5 wt% of anthracite coal, which contains 60.35% of fixed carbon and 1.9% of sulfur, was used as a reductant. All raw materials were mixed homogenously prior to the pelletization process into 10–15 mm of diameter. The reduction process was carried out to 50 g of pellets at 950 °C, 1050 °C, and 1150 °C for 60 min in a muffle furnace at atmospheric pressure. It continued with a wet magnetic separation process to separate ferronickel (concentrates) and impurities (tailings). Iron and nickel grade analysis was performed using XRF, while phase transformation and microstructure were analyzed with XRD and SEM–EDS. The results showed that the sodium sulfate was superior, resulting in the highest nickel grade in concentrate, i.e., 15.06%. The sulfidation mechanism, which could inhibit the metallization of iron, effectively increased the nickel grade in concentrate than decomposition of carbonate and chloridization process. The sulfur content in the reductant also influenced the selective reduction process. It promotes more sulfidation of iron, thus increasing the nickel grade in concentrate.

Jul 7, 2021

By Brian Ulrich

The majority of individuals involved in the mining industry can appreciate and under-stand that mining is an activity that is necessary to satisfy the very basic needs of society, and to assist in accommodating our ever-changing world. As the expression goes, ?if it can?t be grown, it has to be mined.? And at this point in time, society has granted the mining industry the right to go about the business of mining, with the general anticipation that the work will be carried out without causing undue harm to the environment or populations in and around the mining operation. The term ?sustainable development? is gaining momentum as a popular concept, and indeed it has become something of a catch-all phrase, but it is important that the idea behind the term is not cast aside as a nonsense buzz word, as it simply is an indication that development (e.g. mining) can be satisfactorily carried out with an eye toward stewardship of the environment and society. On Feb. 19, 2010, a round-table discussion (Roundtable 2010) on ?Strides Toward Sustainability in Mining? was hosted by Knight Piésold and Co. (Knight Piésold) at the Red Lion Inn and Casino in Elko, NV. Knight Piésold had local representatives (Bryan Ulrich and Steve Boyce), as well as representatives from other office locations (Cynthia Parnow and Rick Damiani from Denver, CO, and Rick Frechette from Tucson, AZ) to help facilitate the discussion. The meeting played host to 30 attendees from five states. Attendees included personnel from nine mining properties and various corporate offices. The majority of participants were people who are directly involved with environmental work on a day-to-day basis. Others were project managers whose jobs involve some level of environmental focus.

Jan 1, 2010

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão Mine in Brazil. They are predominantly blue apatite, followed by green apatite and, less frequently, yellow apatite. The chemical compositions of these types of apatite were determined by electron microprobe analysis and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS). Blue and green apatite responded well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite has the lowest phosphorus pentoxide (P2O5 ) content and largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest phosphorus (P) and calcium (Ca) grades and lowest substitution level.

By C. E. Golson

Modern concrete technology emphasizes the basic qualities required of an acceptable aggregate: it must be clean, sound, homogeneous, and of a size gradation resulting in a concrete of the desired physical qualities at a minimum cost. In the case of coarse aggregates, crushing, scrubbing, and screening will usually provide the required material, although beneficiation is often necessary in order to eliminate unsound or deleterious fractions. Beneficiation is also applicable to fine aggregates,( but the processes most often employed are washing, classification, and dewatering.

Jan 1, 1959

By L. Valentik

Many attempts have been made during the last forty years to evaluate the performance of gravity separation equipment, that is, the effectiveness with which light and heavy particles are separated. The most comprehensive treatment of the subject was made at the 1st International Conference on Coal Preparation held in Paris (1950) by Cerchar. The methods suggested by the Conference were accepted and very widely used in the last 25 years. This paper discusses an improved method of evaluation in the light of the now accepted standard presentation. The float and sink analysis of the product is presented on a Gaussian distribution curve, resulting in an easier visualization of the inherent difficulties of separation. The ogives of the distribution curve are then plotted, giving a quantitative measure of the deviation from perfect separation as an error distance instead of an error area. Illustrations of the new method are given both for gravel and for coal preparation, but the concept is valid and applicable to other types of minerals which are separated by gravity methods.

Jan 1, 1968

By Robert J. Brison

The intent of this paper is to try to answer the complex question: "How much grinding capacity should be designed into a new mining - milling project?" Much work has been devoted to the technical aspects of grinding, the "how" of grinding. But, in the writers' opinion, the economically important subject of optimizing grinding capacity in mill design has not received the attention it deserves, at least not in published literature. For the purpose of this paper it is necessary to distinguish clearly between optimizing operation and optimizing design. Optimizing operation involves making the best use of the available plant and equipment. Much excellent work has been done and is being done in this area. In operation, one can make tradeoffs of production rate and recovery, or recovery and grade, to maximize profits. However, this must be done within the limitations imposed in the design stage. Flexibility is limited by the existing plant. In project design, on the other hand., there are no preexisting physical limitations except as imposed by nature itself; the planners and designers have considerable latitude in their efforts to optimize the overall project. They have complete control over a large number of important design variables from the mine to the finished product. The grinding process design is one of these variables. It not only determines the capital cost charges for grinding and the maximum grinding capacity that operating management will have to work with, but also determines the range of capability of the auxiliary equipment, which fixes the degree of flexibility possible in operation. This paper is concerned with optimizing design rather than operation. The terms "optimum" and "optimize" are sometimes used in a technical sense in connection with grinding, recovery or grade. In this paper, these terms are used only in the economic sense. In this age of working large deposits of ever lower grade ores, it is in¬creasingly essential to design projects and plants for optimum economics, based on the most applicable economic. criteria. Since grinding represents a large part of both capital and operating cost of the project, and largely determines percentage recovery of metal, it should be included as one of the factors in optimizing the project design. This paper is written primarily with reference to medium to large copper concentrators employing conventional wet grinding. However, the principles involved should be applicable to other ores and other methods of grinding.

Jan 1, 1972

By Jürgen Kretschmann

Principally, mining natural resources is a finite business that reaches its limits once the deposits mined are depleted, the resources can no longer be mined in an economically profitable way or substitutes are pushing the mined products out of the market. An example of the latter is the increasing replacement of coal with natural gas and renewables in power generation in the United States [1]. According to the model of the product lifecycle, the global hard-coal mining industry has reached a stagnation phase [2]. The trend is obvious. Coal use peaked in 2013 [3], and the coal demand of China has been slowly decreasing since then [4]. Coal consumption in the United States saw a 16 percent decline from 726 Mt (800 million st) to 608 Mt (670 million st) between 2015 and 2019. In addition, according to the U.S. Energy Information Administration, it will not rise again [5]. The decline is attributed to complex market dynamics, from low gas prices because of the “shale gas revolution” [6] to federal environmental regulations like the Clean Power Plan. Moreover, important players like the United Nations and the European Union have already begun to describe pathways toward decarbonization. Increasing competition between coal-mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries, like France, Spain or Germany, are only forerunners of this development — their centuries of coal production have passed. The concept of sustainable development (SD) is fundamentally based on a model of progress in which ecological, economic and social dimensions should be developed equally and positively. Questions arise, such as: How can SD be a corporate goal in a phase of decline? How can former mining regions sustainably progress to a better future? The steps Germany has taken to handle the coal decline in a sustainable way and the lessons learned from this process are described in this paper. 

By William Gleason

"In 2008, the world quietly hit a milestone that did not receive much fanfare or publicity, but it hit one that marked a turning point in the history of mankind and the way the planet is and will be inhabited in the future. It was in 2008 that, for the first time, more than half of the world’s population, an estimated 3.3 billion people, resided in urban areas. The world’s population had moved from being a majority of agricultural and rural society to an urban society. Andrew Whalley, deputy chairman for Grimshaw Architects, said this change in where and how people live will continue to increase urban populations and, by 2050, it is estimated that more than 6.4 billion people will live in urban areas. To meet these needs, Whalley, speaking during the keynote session of the 2105 Cutting Edge conference in Denver, CO, said future cities will have to be reimagined and redesigned to be more efficient. A large part of that design will be in the infrastructure of those cities.At the Fourth Annual Cutting Edge Conference, Sept. 21-23, much of the discussion was around how the tunneling and underground construction industries improve cities in a number of ways, including societal, environmental and in overall efficiency. There was talk, not just about the improvements that society enjoys at the completion of such projects, but also about the challenges faced by the owner and contractor in the construction of such projects.The conference, titled Urban Tunneling, brought together some of the top minds in the industry to not only discuss the issues faced today, but also those that will shape the industry in the future.For his part, Whalley spoke about a number of projects around the world and how they have impacted society in ways beyond simply providing a better means for transportation of people or water. Notably, he spoke about the Crossrails project in London.London is a city of 8.6 million people and a history that dates back nearly 2,000 years. It is a great example of the challenges the industry faces in bringing modern efficiencies to an established city.Running more than 100 km (62 miles) with more than 42 km (26 miles) of tunnels passing through 40 stations, including 10 new stations, the project is the largest in Europe and will transform the way people move about the city."

Jan 1, 2015

By K. Burke, K. L. Myers, R. Espell

Barrick's Goldstrike AA heap leach pad is an HDPE-lined facility that was used for gold recovery from low-grade ores using conventional cyanide heap-leach technology. The pad was operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA leach pad facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada's closure requirements. The traditional Nevada leach pad closure procedure involves rinsing to reduce the cyanide concentration to an acceptable level followed by reclamation. However, rinsing does not typically reduce certain metals and compounds, and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as in Nevada, the fine-grained layer will rarely reach saturation, and the cover will be able to store water during precipitation events and will allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22-m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the recontoured AA heap leach pad was specifically designed to enhance the re vegetation, reclamation and sediment yield control aspects of the AA heap leach pad closure, while resulting in a natural looking surface that is compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for recontouring and erosion-control design.

Jan 1, 2002

By Harvey P. Knudsen

This paper illustrates the application of geostatistics to a roll front type uranium deposit located in Wyoming. The steps involved in calculation of experimental variograms, variogram modeling and verification of the resulting models are described in detail. The resulting spherical variogram models for grade thickness and thickness show strong geometrical anisotropies. The major axis of anisotropy for both variables is approximately parallel to the axis of the roll front and the minor axis perpendicular to the roll. This model confirms the technique of drilling "fences" across the roll front, where the drilling is much closer together than the fences along the roll.

Jan 1, 1978

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The Industrial Internet of Things (IIoT), a concept that combines sensor networks and control systems, has been employed in several industries to improve productivity and safety. U.S. National Institute for Occupational Safety and Health (NIOSH) researchers are investigating IIoT applications to identify the challenges of and potential solutions for transferring IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40 percent of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system using low-cost microcontroller Wi-Fi boards to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communication and tracking infrastructure.IntroductionThe U.S. approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communication with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT).IoT is the network of physical objects, or “things,” embedded with electronics, sensors and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator and/or other connected devices (Atzori, Iera and Morabito, 2010; Gubbi et al. 2013). It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: the Internet and things. The first word pushes toward a network-oriented vision, while the second tends to put the focus on generic objects. The traditional Internet can be viewed as an internet of computers, so things connected to the Internet are computers only. IoT extends the internet by allowing other generic things that are commonly found in daily life, such as refrigerators and cars, to be interconnected through the Internet, thus creating a bridge between the virtual world and the physical world"

Jan 12, 2017

By E. G. Kelly

This paper describes the performance of a modern compound trough profile spiral that is optimized for fine coal cleaning. Reduced performance (Tromp) curves are presented to compare these new spirals with older designs, as well as with other commonly used coal cleaning equipment. As an aid to equipment selection and circuit design, data are also presented to show how variables, such as flow rate, pulp density, and particle size affect efficiency and the separation specific gravity.

Jan 1, 1984

By A. Singh

"Considering the dominant role of fertilizers in global phosphate production, it is evident that with the ever increasing development in agriculture there will be a growing demand for phosphate beneficiation. With the rapid depletion of high quality reserves, investigations into more complex and lower grade ore bodies are required. The Minerals Processing Division at Mintek has been involved in process development and flowsheet design projects on phosphate resources since 2003. This paper will discuss the processes that Mintek has explored and employed to upgrade various phosphate ore bodies (>30% Phosphorous Pentoxide (P2O5)) in preparation for end user application. These are aimed at an improved understanding of ores in terms of their varying mineralogy and the development of appropriate process routes to meet product specification. OVERVIEW OF MINTEK Mintek is a state owned science council that undertakes R&D, consulting and sells products and services into the minerals beneficiation industry. Mintek has been in existence for 83 years with a current permanent staff complement of 750 of which 300 are professionals with a tertiary education. Being a non-profit organisation, the majority of funding comes from state grant and earmarked funding. All research is needs-driven exploring innovation through technology and process optimisation trends. Owing to a solid base of expertise, extensive laboratory and pilot facilities, and a historical database of knowledge, Mintek is well positioned and equipped to execute projects on a scoping, feasibility, prefeasibility and bankable level. USES OF PHOSPHATE Phosphate is the component in fertilizer essential for root and stem development in plants as well as rejuvenation of harshly depleted soil for which there is no agricultural substitute. Phosphate rock is essential for global food security with 87% used in the production of fertilizers. In agriculture as fertilizer, phosphate is one of the three primary plant nutrients in addition to nitrogen and potassium. In former times, it was simply crushed and used as is, but the crude form is now only used in organic farming. Normally it is chemically treated to make Single superphosphate (SSP), Triple superphosphate (TSP), or Mono-ammonium phosphates (MAP) and Di-ammonium phosphates (DAP), which has a higher concentration of phosphate and is more soluble, thus more suitable for plant absorption."

Jan 1, 2018