Search Documents

Water and wind erosion of toxic zinc and lead smelter waste is one of the most urgent environmental problems to be solved in the Silesia region of Poland. Over 87 x 106 Mg of various mining wastes were disposed of in uncontrolled piles leading to soil, water, and air pollution in highly populated areas. Welz and Doerschel process Pb/Zn smelter wastes were stabilized in the summer of 1994 by application of heavy loads of CaCO3 (30 Mg/ha), CaO (1.5 -15 Mg/ha), and municipal biosolids (150 -300 Mg/ha), followed by seeding with a mixture of acid-and salt-tolerant grass species selected in a pot experiment. Vegetation was successfully established on 85% of the Welz material demonstration plot area (0.5 ha), even though it was initially high in water-soluble Zn, Pb, and Cd ranging from 0.4 to 1311,0.1 to 5.8, and 0.05 to 55 mg/kg, respectively. Standing biomass averaged 3.3 Mg/ha on the stabilized Welz waste zone by the end of the third growing season (1997). The revegetation of much of the Doerschel material area failed initially because of extremely high salinity (16 dS m-1), high content of water soluble metals (Cd in particular), and heavy compaction. The area was capped (15 cm) with waste lime and retreated with bio-solids (300 Mg/ha) in 1995, and standing biomass averaged 2.9 Mg/ha in the fall of 1997. The observed plant response to bio-solids and lime indicates this approach to be an environmentally beneficial technology as compared to the traditional methods utilizing topsoil covers.

Jan 1, 1999

"In the conceptual stages of engineering, benchmarking and empirical ratios are commonly the only references for estimating the production rate of greenfield projects. For underground mining projects, the lack of similar cases often makes the comparison difficult due to each project’s unique geology, rock quality or other singular characteristic. This paper discusses an analytical alternative for determining the maximum achievable production rate for underground stoping mining by modeling production as a continuous process. The results show that long-term maximum capacity depends exclusively on the achievable development rate and the development intensity of the design. In operations constrained by backfill, the development rate could be limited by the backfilling rate. Extraction rate and stope size only have impacts on capacity estimates during the ramp-up period.These findings allow shaping of the maximum capacity profile of a project. They can be used as a tool for quick assessment of conceptual capacities, and sensitivities of mining rates. Benchmarking tests compared favorably with projects, mines in operation and scheduling exercises. IntroductionA key consideration in the value proposition of a mining project is its capacity or production rate (Tatman, 2001). At a conceptual level, it is common practice to refer to empirical references (Taylor, 1986; Long, 2009), rules of thumb (de la Vergne, 2014), benchmark ing studies or consultant experience to estimate or validate a target value. There is, however, a lack of analytical methodology to guide an early estimate of the maximum capacity.Araneda and Gaete (2004) presented an interesting mathematical approach to estimate the capacity of panel caving mines. Using a continuous model, they confirmed that the mine capacity is essentially determined by the rate of area incorporation, in terms of area per period, and ore column height. This simple relationship has been confirmed by multiple detailed scheduling works"

May 1, 2016

Silver bearing bulk sulfide concentrates from several Peruvian mines were autoclaved in a 19 liter (five gallon) laboratory autoclave in Lima, Peru. Cyanidation of autoclaved concentrates following a hot lime jarosite destruction step extracted over 98 percent of the silver and over 95 percent of the gold. Autoclave operating parameters such as time, temperature, pulp density and autoclaved solids recycle were investigated and reaction rates determined. The problems of excessive heat generation, silver solubility during autoclaving, and formation of pellets containing unreacted sulfides were addressed. The data presented will be used to design a continuous autoclave pilot plant to pro-vide reliable scale up data for a 50 -100 ton per day facility.

Jan 1, 1992

By A. Newman, M. Goycoolea

"In this paper, we consider an underground production scheduling problem consisting of determining the proper time interval or intervals in which to complete each mining activity so as to maximize a mine’s discounted value while adhering to precedence, activity durations, and production and processing limits. We present two different integer programming formulations for modeling this optimization problem. Both formulations possess a resource-constrained project scheduling problem structure. The first formulation uses a fine time discretization and is better suited for tactical mine scheduling applications. The second formulation, which uses a coarser time discretization, is better suited for strategic scheduling applications. We illustrate the strengths and weaknesses of each formulation with examples.IntroductionProject scheduling is an important aspect of underground mine planning that consists of determining the start dates for a given set of activities so as to maximize the value of a project while adhering to operational and re-source-availability constraints. Important activities that require scheduling include development, drilling, stoping and other ore-extraction techniques, and backfilling. Precedence relation-ships impose an order in which activities can be carried out based on their location in the mine: for example, the activity a associated with development of an area must be completed before the activity a´ associated with extraction of that same area can begin. Re-sources include attributes of the mining operation, such as the amount of extraction and mill capacity available per time period, and are determined by capital and equipment availability and other factors. In this paper, for our set-ting, resource-availability constraints consider the amounts of material that can be extracted and sent to the mill — that is, processed — per time period."

Mar 1, 2017

By B. Govindarajan, T. C. Rao, M. Vanangamudi

The results obtained from hatch, flotation experiments on two coals were used to develop relationships between the recoveries of water and solids into the concentrate. When the recovery of non-ash material (RN) for any size fraction is plotted against a parameter X, defined as [x _ Amount of (W) recovered x Collector dosage (C)in the concentrate (cc)(kg/t)] a single "non-ash recovery curve" is obtained. Non-ash recovery curves thus obtained from different size fractions are used to get a unique "modified non-ash recovery curve" for a given coal, using the reduced efficiency curve concept. Similar observations have been noted in the case of recovery of ash material (RA) also. The amount of water recovered into the concentrate is plotted against a parameter "Water Recovery Factor (WRF)," defined as [WRF = T.F.(1+C)] where T is time (in sec) and F is frother dosage (in kg/t). Plotted in this form a characteristic water recovery curve, for a given coal is obtained that may be defined by the following equation: [W4=W_(1 pWRF-e] The above relationships have been verified against the experimental results obtained from three more coals and are found to give satisfactory predicted values.

Jan 1, 1992

By J. A. Hartlage

Four years ago, Ashland Chemical Company introduced a new copper solvent extraction reagent for hydrometallurgical utilization. The reagent, an alkylated 8-hydroxyquinoline, is called Kelex 100 ®(1). Since the time of introduction, the reagent has been investigated by several workers for its solvent extraction utility in the separation and purification of transition metals (2-7). In the following text, those factors which are essential to the optimum performance of Kelex 100 on concentrated copper solutions will be discussed. To date, the reagent has been found useful in active concentrations of from 1 to 20% Kelex 100. In order to achieve the best performance for Kelex 100, it has been found that a phase modifier is essential. Various alcohols and phenols have been evaluated in order to improve phase performance and stripping characteristics of the solvent system. Modifiers and diluents are especially important when solvent activities between 3 and 20% Kelex 100 are employed. A 15% Kelex 100 solvent, for example, containing 15% nonyl phenol in Escaid 100 (Exxon) can be utilized to remove greater than 33 grams per liter of copper from an aqueous feed without interstage neutralization, and in the same process scheme the reagent can be stripped to less than 1 gram per liter barren organic producing a pregnant electrolyte containing greater than 40 grams per liter copper and less than 120 grams per liter sulphuric acid. The unusually efficient stripping of Kelex is accomplished by protenation of the extractive molecule during the stripping process.

Jan 1, 1974

By Philip R. Whitney

Precipitation of hydrous manganese/iron oxides in streams can be readily observed in much of the northeastern United States, and is apparently a common phenomenon in other glaciated areas (1,2,3,4). Deposition occurs when Mn-enriched ground or surface water enters the stream environment and encounters conditions of higher Eh and pH. The preferred location for deposition is in shallow, fast-flowing segments of stream; the oxides usually form as coatings on detrital material. The experimental studies of Hem(5) and a considerable amount of work on marine and lacustrine manganese nodules(6,7,8) suggest that given an appropriate substrate, deposition of manganese oxides may occur even when the water is undersaturated in Mn with respect to the oxides, due to catalysis by organisms or by silicate, carbonate, or ferric hydroxide surfaces. Once begun, manganese oxide deposition is autocatalytic (9). Studies of the distribution of oxides in various size fractions of stream sediments indicate that the thickness and prevalence of the coatings commonly increases with increasing particle size in the coarse sand and gravel size ranges. Figures 1 and 2 show a fairly typical distribution of leachable metals over nine size fractions from 62 microns up to 8-16 mm. The leaching solution used was neutral ammonium citrate with hydroxylamine hydrochloride, which effectively removes the oxide coatings without significantly attacking most silicates, carbonates or sulfides. Figure 1 shows metal content as ppm of the total sample; figure 2 shows' the same data as micrograms of metal per square millimeter of surface area.

Jan 1, 1975

By Yanan Zhang, Hongwei Deng, Feng Gao, Bo Ke

Recently, liquid carbon dioxide (L-CO2) blasting technology has attracted attention due to its good fracturing effect and safety performance, especially in coal seam permeability improvement. This paper analyzes the blasting effect of L-CO2 based on experiments and studies the fracturing mechanism from the perspective of stress wave action via theoretical analysis and peridynamic simulations. The results indicate that L-CO2 blasting achieves a good fracturing effect without forming a crush zone, and the loading rate and strength of the stress wave are key factors.

Jan 19, 2022

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicrometer size range and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicrometer size range. As dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using an impactor-type size selector such as the DPM impactor (DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) are an alternative size selector for DPM sampling applications, with a major advantage that, by design, they should not be susceptible to rapid aging. This paper presents the results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device and, eventually, a reduction of its effective particle cut size, but when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions of this study, the effects of SCC aging were observed to be minimal at the end of the study period. IntroductionSubmicrometer-sized particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, Gussman and Meyer, 2000; Ristovski et al., 2012). Diesel particulate matter (DPM) represents a major source of submicrometer particles in both public and occupational environments (Kittelson, 1998; Abdul-Khalek et al., 1998). Relative to other occupational groups, underground miners can have some of the highest DPM exposures due to their work in confined spaces where large diesel equipment is used (U.S. Environmental Protection Agency, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as soot, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007; Birch, 2016)."

Jan 8, 2018

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device IntroductionTwo recent regulations have modified operators’ rock dusting schedules in order to meet compliance standards. First, the 80 percent incombustible requirement in intake entries has increased both on-section and out by the- section rock dusting. Secondly, the recent change to the respirable dust regulation has increased the number of respirable dust samples taken per sampling cycle. Previously, when only five samples were needed bimonthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule.The significant number of samples now required under new regulations, combined with the need to maintain 80 percent total incombustible content in active mining areas, require the schedules for respirable dust sampling and rock dusting to overlap. Although rock dust is considered a nuisance dust in relation to U.S. Mine Safety and Health Administration (MSHA) sampling, these overlapping schedules raise concerns about the amount of rock dust that potentially is included in the sample. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 effective Aug. 1, 2016, increasing concern that rock dust contamination may be an issue (MSHA, 2016). Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application, or to schedule rock dusting during a maintenance shift when the number of miners present is lower."

Jan 5, 2017

By J. Drimmer

The past several decades have seen the rapid expansion of multinational mining companies? exploration and production activities around the globe. This trend has resulted from a number of factors, including increased demand for resources as a result of worldwide economic growth, the diminishment of known and proven reserves, rising commodity prices, technology improvements, and the liberalization of investment regimes in developing countries with significant natural resources. With those opportunities, however, come associated risks and significantly increased legal compliance obligations that may be imposed by various bodies. That includes domestic regulations, as well as foreign civil and criminal laws with extraterritorial reach. A failure to adhere to those laws can have dire consequences, including substantial monetary fines and penalties, severe damage to a company?s reputation, and even jail time for individual company employees.

Jan 1, 2010

By Stanley N. Watowich

Recently the petroleum market has made us aware that we are indeed global natural resource consumers, and as such, we have become captive to fundamental global resource economics and their attendant vagaries. Global resource supply problems are as old as civilization and mineral exploration one of its important catalysts. On the basis of natural resources empires have been expanded and new frontiers have been developed. Global consumption and production might even be viewed idealistically as a system dedicated to optimizing distribution to the consumer. However, this is not the case. Political instability and increased government polarization make dependency on a global market somewhat insecure. The U.S. must evaluate its domestic mineral re- sources on the basis that all metals are critical and that dependency on even the common and base metals may ultimately weaken our domestic economy and our potential international relationships and could cause critical weaknesses as demonstrated by the petroleum problem. This paper evaluates specifically the Duluth Gabbro Complex, of Northeastern Minnesota, (figure l), as a potential resource of critical and strategic metals. First, a chronology of some of the early exploration, will be followed by more recent intensive company studies and preliminary evaluations of economic feasibility. Lastly, metallurgical data, on some optimum conceptual mining plans will allow metal production data to be compared with an estimate of U.S. domestic needs in 1990. The purpose of this paper is to put into focus the difficulty of converting resources into vitally needed reserves.

Jan 1, 1981

By R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance is reviewed.

Jan 1, 1999

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By K. Lang

The use of high-efficiency electrical submersible pumps (ESPs) for large scale, open pit mine dewatering operations provides a good example of how technology, products and services from the oil and gas industry can be adapted to the mining industry. In this case, the mine is Goldcorp?s Peñasquito in the Zacatecas state of Mexico, at the Peñasco and Chile Colorado open pit deposits. The technology, products and services are from Schlumberger artificial lift (AL) and Schlumberger industrial water services (IWS). Overview of high-efficiency ESPs This section provides a brief description of the basic components, specifications and operating capacity ranges for the ESPs compared with traditional or conventional dewatering well pumps. This information helps to establish how ESPs provide certain functional and economic advantages over conventional pumps in a mine dewatering application. A schematic of a high-efficiency ESP in an oil and gas (O&G) application is shown in Fig. 1.

Sep 1, 2013

By Norman R. Paterson

In November 1980 a combined airborne electro-magnetic (INPUT.) and magnetometer survey was conducted by Questor Surveys Limited in the State Line Area, Colorado-Wyoming. The survey was the result of discussions over a prolonged period between the authors and various investigators of the State kimberlite occurrences. As a result of these discussions and literature studies, it was decided that airborne geophysical methods would be potentially useful in the exploration for new kimberlite occurrences. The survey was designed by Paterson, Grant and Watson Limited and conducted by Questor Surveys Limited over an area in which more than 15 kimberlite bodies were known and on some of which ground geophysical surveys had been conducted. The survey was designed primarily to determine the airborne electromagnetic and magnetic responses of the known occurrences and to deter- mine whether these responses would be detectable under similar conditions in other parts of the State Line District and elsewhere.

Jan 1, 1984

By Andrew W. Jenike

The first significant studies of problems related to the handling and storage of bulk solids were reported at the end of the nineteenth century. Early work originated from the necessity to store large quantities of grain and was concerned mainly with pressures affecting the structural design of silos and bins. The Janssen formula (about 1898) and the work of Ketchum [1] form the highlights of that period. In more recent years, progress in mechanization, increasing plant capacities, and rising costs of labor have focused the attention of engineers on the problem of gravity flow of bulk solids. A great deal of work has been done with models, and flow patterns obtained in small scale bins have been described in several publications, for example [2, 3]. An attempt to develop a theory of flow of bulk solids was reported in 1954 [4, 5, 61 and presented to the in a paper [7] in the same year. AIME recommended the continuation of this work and, as a result, Engineering Foundation granted a sum of money to set up a Bulk Solids Flow Laboratory. Two and a half years ago the project gained the support of the University of Utah and a laboratory was set up on the campus of the University. This project is now in progress, it has received the support of the American Iron and Steel Institute and of Kaiser Engineers, Division of Henry J. Kaiser Company. The results obtained to date are summarized in this report.

Jan 1, 1959

By Madeline Mello, Michael Low, Nick Karlin, Bryce Scofield

The LA Effluent Outfall Tunnel is the first tunnel in the United States to incorporate post- tensioning into the precast segmental lining. Several unique components were integrated to ensure that the post tensioning could be carried out successfully in the tunnel, even concurrently with the TBM excavation. This also required the development of new processes both in the casting facility and in the TBM to ensure that the almost 3,700 rings could be successfully manufactured, threaded, stressed, and grouted. This paper will discuss the material selection, fabrication, and installation of, as well as lessons learned from, this first in country tunnel lining.

Jun 23, 2024

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, despite its natural abundance, demand for coal exceeds its countrywide supply due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98 percent of total raw coal production in the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an environmentally friendly manner, especially in populated areas adjacent to the mining zone. This technology eliminates blast hole drilling, blasting and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks.

May 1, 2023

By Ava Segal, Doga Cagdas Demirkan, Abhidipta Mallik, Sebnem Duzgun, Andrew J. Petruska

Search and rescue operations in mining heavily rely on humans. In the context of emergency situations within underground tunnels, the potential to utilize sensory technology for navigation assistance holds the promise of saving human lives. Our research introduces a device configuration designed to enhance the performance of search and rescue teams. This setup integrates LIDAR and thermal cameras with the Microsoft Hololens, facilitated by the NUC computer and ROS Bridge. Performance assessment involves quantifying the extent to which a user is willing to venture into a light-deprived section of the mine prior to necessitating supplementary illumination. The preliminary outcomes highlight the significant potential of augmented reality assistance in offering indispensable aid to first responders, thereby greatly augmenting the efficiency of search and rescue missions conducted during critical circumstances.

Feb 1, 2024