Search Documents

By H. N. Dougherty

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) ventilation gallery was used to study methane-air flows around a continuous miner mockup with water sprays and a scrubber fan. Methane gas was released from pipes located at the face to simulate face gas emissions. Methane concentrations and air velocities were measured while varying parameters such as airflow quantity, entry width (sump or slab cut), and face ventilation configuration (blowing or exhausting curtain). Test data showed a similar pattern of methane concentrations at both low and high airflow quantities, but a difference in the distribution of methane concentrations between narrow and wide entry widths. Most tests showed that blowing face ventilation was more efficient in diluting methane than exhausting ventilation, similar to observations made in previous empty gallery studies. The patterns of airflow and methane concentrations observed in this testing can further improve the understanding of airflow in and around the CM and face, promoting effective use of face ventilation to improve the health and safety of miners. INTRODUCTION Attaining an accurate understanding of airflow distribution at the continuous miner face is instrumental in maintaining a safe mining environment. US mining regulations require that sufficient airflow must be directed to the deepest penetration of the face and render harmless contaminant gases, as verified by the Mine Safety and Health Administration (MSHA). Currently, continuous miner face air readings can be taken in the last open crosscut and at the inby end of the curtain mouth. By measuring adequate airflow in a pre-determined area it is accepted that a sufficient quantity of that air exists to sweep the face of harmful dust and gasses. Unfortunately, due to the location inaccessibility, precise face velocity readings cannot be measured in situ. Face velocities may be estimated through computer-simulated programs based on laboratory models. Improving upon previous empty gallery testing and to more effectively determine representative face methane readings, a mockup of a continuous miner with water sprays and a scrubber fan was used in the current study to further refine face airflow conditions that would be closer to actual mining conditions."

Jan 1, 2016

The 6th International Mine Ventilation Congress (IMVC) was held May 17-22,1997, in Pittsburgh, PA. This marked the second time that the IMVC was held in the United States. The first congress, organized in 1975 by the Mine Ventilation Society of South Africa, was held in Johannesburg. Since then, the meetings have been held every four or five years, with the 1979 meeting being held in Reno, NV. This was followed by Harrogot, England, in 1984; Brisbane, Australia, in 1988; and Johannesburg, South Africa, again in 1992. The IMVC provides an international forum in the field of mine ventilation for the purpose of sharing technology and experience. The meetings are attended by ventilation engineers, academics, consultants, government employees and vendors interested in mine ventilation. As was evident from this meeting, significant progress has been made in the field of mine ventilation. However, disasters continue to occur around the world and long-term health problems continue to affect workers. So there is a need for further improvements in ventilation technology. The highlight of the conference was the technical sessions in which more than 80 papers were presented by authors from more than 20 countries. In addition to the technical sessions, the conference featured field trips to a number of mine properties throughout the United States. Five short courses were offered on topics ranging from respirable-dust control to mine fires and explosions. The conference also featured a trade show. It exhibited the latest advances in ventilation equipment, computer application software, consulting and engineering services, and health and safety equipment.

Jan 1, 1997

By John E. Good

A new coal boom is under way in western Canada. As recently as the mid-1960's, the coal industry in western Canada was considered stagnant and, by some people, dying. But Japan's growing need for coking coal, which became more pronounced in 1966, sparked great interest in western Canadian reserves.' As a result of a rapidly expanding export market and growth in domestic demand, Canadian coal production spurted to 16.6 million tons in 1970. Production in 1965 was 11.5 million tons. Today, about 60 percent of Canada's output comes from western Canada, but by 1975, 87 percent (23.1 million tons) is expected to come from this area, and 96 percent (68.3 million tons) by 1990. Opening, developing and operating new coal mines to meet the needs of a rapidly expanding market for western Canadian metallurgical coals pose some unique and difficult problems. Covering nearly every aspect of opening properties in remote areas, the problems are met in exploration, transportation, construction, mine operations, coal preparation, manpower and ecology. Paul Weir Company has been involved as coal consultants on various projects in western Canada for some years. In presenting this paper, we make no attempt to present an in-depth or detailed analysis of any one specific situation. Each has, or would have, its own peculiarities or characteristics, both physical and economic. Instead, the objective is to provide for those not intimately

Jan 1, 1972

By Camilo Quintero, Frank Cesario, John Kinnear, Brian Boye

In this paper, an innovative approach was adopted to automatically calculate the effects of tunnel induced settlement on buildings and utilities. The approach resulted in increased output quality, consistency, reduced time, cost savings and a greater ability to respond quickly to design changes. The techniques described have been applied to the Fairbank Silverthorn Storm Trunk Sewer System project, located within the City of Toronto. The automation allowed a very large area of topography, tunnels (6 km), buildings (9000) and utilities (over 1000) to be rapidly evaluated. Visualization of the settlements and impacts also allowed the project design team to optimize the system design to mitigate the settlement impacts.

Jun 13, 2021

By T. L. Barone, J. R. Patts, L. D. Patts, S. J. Janisko

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more effective and efficient use of rock dust. A prototype flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed inline between the face ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over three days at set distances from the fan exhaust to assess changes in float coal dust levels in the return due to operation of the scrubber. Mass-based measurements were collected on a per-cut basis and normalized on the basis of per ton mined by the continuous miner. The results show that average float coal dust levels measured under baseline conditions were reduced by more than 90 percent when operating the scrubber. IntroductionAirborne coal dust is a byproduct of coal production, and engineering controls exist to deal with both the respirable dust health hazard as well as the float dust explosion safety hazard. Float coal dust, smaller than 75 µm (0.003 in.) in size, can deposit throughout mine entries and propagate explosions that had been initially fueled by methane gas. The inertization of float coal dust with rock dust helps prevent a potential secondary float coal dust explosion, but a preferable course of action is to significantly reduce the hazard by removing float coal dust from the airstream before it has the opportunity to deposit on the mine’s surfaces.Since 1970, disasters due to explosions in underground coal mines have caused 201 deaths in the U.S. mining industry, including 29 deaths in a single mine explosion in 2010 (Wade, 2010; U.S. Mine Safety and Health Administration, 2015). The U.S. National Institute for Occupational Safety and Health (NIOSH) had initiated a fiveyear research project that aims to investigate methods and technologies to reduce the potential for secondary coal dust explosions by the purposeful capture and/or suppression of float coal dust prior to its deposition on the mine roof, rib and floor (NIOSH, 2013). The project aims to evaluate the efficiency of methods to reduce longwall and belt airway float dust in the general airstream as well as methods to capture it at or near the source. Prioritization is given to longwall sections given the amount of coal produced relative to continuous miner sections, but the research is open to technologies that may be adapted from one method of mining to another."

Dec 1, 2016

By Staff

In 2012, the estimated value of mineral production increased in the United States for the third consecutive year. Production and prices increased for most industrial mineral commodities mined in the United States. While production for most metals remained relatively unchanged, with the notable exception of gold, the prices for most metals declined. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals? contribution to the GDP increased for the second consecutive year. Trends in other sectors of the domestic economy were similar to those in mineral production and consumption rates (Table 1). After continued decline following the 2008-2009 recession, the construction industry began to show signs of improvement late in 2011 and throughout 2012, with increased production and consumption of cement, construction sand and gravel, crushed stone and gypsum, mineral commodities that are used almost exclusively in construction.

May 1, 2013

By A. Noble

"Froth flotation circuits are widely used throughout the mineral processing industry for the concentration of fine particles. It had been estimated that nearly 2 Gt (2.2 billion st) of ores are treated globally each year using this versatile separation process (Fuerstenau, 1999). Due to the high feed tonnage, a large economic incentive exists for flotation plant operators to optimize the performance of this critical processing circuit. Prior to the 1950s, the optimization of flotation circuits primarily involved the manual adjustment of operating variables based on visual observation and sporadic sampling (Lynch, Harbort and Nelson, 2010). During the next several decades, however, the advent of improved on-line instrumentation coupled with the rapid development of high-speed microprocessors allowed the industry to develop more advanced control systems that could quickly adjust operational parameters in response to disturbances in ore characteristics and plant flows. These early online controls typically involved feedback loops designed to stabilize cell performance through the automatic manipulation of process variables such as pulp levels, gas rates and chemical dosages. The set-points for these controllers were often set by plant operators based on one or more operator objectives, such as maximizing throughput, recovery or grade. More recently, these regulatory controllers have been interfaced with high-level data display and management systems that provide operators with the ability to better optimize flotation plant performance based on mathematical models and rule-based algorithms (Greet, 2010).While tremendous strides have been made during the past several decades, even the most modern flotation plants are still faced with the long-standing question: “What are we trying to optimize?” From an operator perspective, some common responses include “Maximize tonnage of saleable concentrate” or “Maximize metals recovery at a customer-specified market grade.” These replies may or may not reflect those of management, who often focus on economic goals such as “Maximize profits for each operational unit” or “Maximize rate of return for all corporate assets.” Unfortunately, these high-level objective statements do not always translate well into practice due to the disconnect between plant operating protocols and product value. Attempts have been made by industry to overcome this issue using various types of optimization routines such as linear programming or other optimization engines. While this approach does have some merit, these blind routines require considerable input data and interpretational expertise and provide little or no fundamental insight that can be used to drive improvements in concentrator performance."

Feb 1, 2017

By M. Albrecht

In the mining industry and particularly in the processing plants, we use some large and unusual equipment. Understanding what it is and what it does is important to good operations, but how do you teach a new employee. When I started out in this field, the information on the processing equipment was easy to come by. Equipment manufacturers readily supplied it; their salesmen, often engineers themselves, knew how important the availability of this information was. Old engineers used their notebooks to train the new engineers. Over time this has changed. Equipment manufacturers have changed hands or gone out of business, and often the older engineers are gone. As a start in reversing this, this presentation will be an introduction to sizing, selecting, and operation of some of this equipment, in particular gravity separating equipment. Major portions of this have been excerpted from A Mining Engineers Notebook: Mineral processing (2).

Feb 23, 2014

By Joseph E. Worthington

The Haile Gold Mine is one of the earliest gold discoveries in the eastern United States as well as one of the largest gold producers from that region. Gold was first discovered in the gravels of what is now known as Haile Gold Mine Branch in 1828 on lands then owned by Colonel Benjamin Hale (spelling not the same). Small placer workings were immediately started and it was not long before the surrounding residual soils and saprolites were also found to contain gold. Following the presence of gold in the residuum eventually lead to the discovery of the underlying gold-bearing lodes that actually outcropped in saprolite form where not masked by heavy vegetation or a thin veneer of Coastal Plain sand. The earliest attempts at production, immediately after discovery, utilized slave labor, washing gravel and residuum from leased tracts that were 15m (50 ft) square. Several at- tempts at small milling operations were made during the en- suing decades, but there was really no substantial or successful production until the 1880s.

Jan 1, 1990

By Karan S. Keith, Haydn H. Murray

The sorptive and impervious nature of clay materials was recognized long before modem technology allowed us to understand the physiochemistry of clays. In Cyprus, around 5000 BC, sorbent clays were used for fulling woolen cloth. One of the earliest recorded uses of clays as an impervious liner was more than 3200 years ago in the construction of a bitumen-sand-gravel-clay liner built along the embankment of the Tigris River at Assur. Today one of the most common applications for clay minerals in the environmental industry is for use as impermeable barriers to fluid transport. Clay minerals are fine in particle size and thus have large surface areas, which, as a result of intermolecular forces and ionic substitutions, make them excellent materials for both ion exchange and ion sorption. Therefore it was logical to consider certain clay materials for applications in the environmental industry, where they can act as physical and chemical traps for potential contaminants. Certain bentonites have historically been used as sealants for fluids (Grim, 1962), and other clays have been used as sorbents for both water and oil (Haden, Jr., 1972). Prior to the 1980s, disposal of the nation's municipal, commercial, chemical, and nuclear wastes was largely indiscriminate and poorly regulated. This created environmental pollution problems, especially with respect to groundwater contamination. Promulgation of federal regulations like the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA - commonly known as Superfund) have forced a more careful and costly approach to waste disposal. The US Environmental Protection Agency (EPA) is the government body charged with enforcing and ensuring compliance with federal regulations governing toxic waste production, storage, and disposal. Widespread application of geotechnology to the design and construction of waste containment systems and to pollution remediation has become necessary due to such laws and because of increasing use of the subsurface environment for the disposal of hazardous wastes. In the United States nearly 1.8 kg of trash is disposed of per person per day, which amounts to nearly 181 Mt per year. This amount is more than double the waste produced in 1960, and these numbers are expected to continue to increase. Canada produces approximately 1.68 kg of waste per person per day. The EPA estimates that in the United States 64% of our garbage is landfilled, 18% recycled, and 18% incinerated. Even with continued increases in recycling and incineration efforts, the EPA projects that the United States will still need 82% of today's landfill capacity in the year 2000. Data on the exact number of landfills in the United States and Canada is conflicting in part because of changing definitions of what constitutes a landfill and because of inadequate record- keeping by some states and provinces. An estimate of the number of municipal solid waste (MSW) landfills in the United States in 1990 to 1991 ranged from 4 462 to 10 467 with an average estimate of 6 600. In Canada the number of MSW landfills reported varied from 5 493 in a 1982 survey to 1 766 reported in a 1991 National Solid Wastes Management Association (NSWMA) survey (Repa and Sheets, 1992b). A properly operated MSW landfill on average requires 1 hectare of land per year per 25 000 people (Coates, 198 1). In addition to MSW facilities, there are also waste disposal facilities needed for hazardous waste and low level and high level radioactive waste. In 1983, approximately 266 Mt of hazardous waste was generated in the United States, almost 50% of this by industrial production. About 68% of the hazardous waste generated in the United States and Canada and almost 50% generated in Europe are still landfilled (Egger, 1987). In 1985, approximately 51 000 m3 of commercially produced low level radioactive waste was disposed of in radioactive waste disposal sites across the United States (Jungling and Greeves, 1989). By 1987, the US defense program had produced approximately 10 000 t of high level nuclear waste. In addition, there were approximately 14 000 t of spent fuel assemblies from commercial nuclear power plants in temporary storage; the amount is expected to nearly triple by the year 2000. Presently most commercial spent fuel assemblies are stored in water-filled pools at nuclear power plants. Defense waste is stored on federal reservations in surface and underground steel tanks (Anon., 1987). Under federal law nearly all waste disposal and containment sites are required to have a liner or barrier and a cover system design that meets federal- or state-approved hydraulic conductivity requirements for the type of waste that the site will receive. When approved materials, necessary for constructing the waste containment structure, are not available on site, one of the most economical ways to meet these requirements is through the use of clay, soil/clay, or clay/geotextile materials. In a 1991 survey by NSWMA of its members and other select private sector facilities, 81% of the surveyed landfills had some type of liner system. About 75% of these liners were clay materials (either recompacted or natural). The remaining 30% were using flexible membrane liners as part of a liner system. Clay liner materials are most commonly used in the South, Midwest, West-central, and South-central regions of the United States. About 93% of the landfill facilities had closure plans, and of these 91 % were using clay materials in some way for the final cover material (Repa and Sheets, 1992a). Waste barriers and containment structures take several basic forms, and they are used in a variety of different applications: 1) cutoff walls, 2) soil or soil/clay-admix liners, 3) geosynthetic bentonite-clay/geotextile membranes, 4) radioactive waste containment barriers, and 5) synthetic geomembranes. This chapter will discuss the first four of these categories. The field of synthetic geomembranes, although a related topic, is beyond the scope of

Jan 1, 1994

By Jack V. Hill

A unique type of grinding mill liner has been developed by Waagner-Biro A.G. of Austria. This liner system, termed an angular spiral lining (.ESL), was, successfully tested by Magma Copper Company's San Manuel concentrator in both their 10 Ft x 10 Ft (3.05m x 3.05m) and 12 Ft, 6 In x 14 Ft (3.81m x 4.27m) grate discharge wet grinding ball mills. Magma Copper's savings in power and grinding balls justified conversion of more than half of their twenty-six ball mills to the ESL system.1,2 The ASL system was provided by the Capitol Castings Division of Midland Ross Corporation, the exclusive licensee for such conversions. Capitol Castings proposed the following as expected benefits from installation of an ASL system in an 18 Ft x 21 Ft (5.49m x 6.40m) overflow discharge wet grinding ball mill at the Pinto Valley Operation of Cities Service Company: "(a) Reduction of power consumption per ton of ore milled = 12%, (b) Increased throughput = 6%, (c) Reduction of ball consumption = 6%."

Jan 1, 1982

By M. C. Roberts

The material composition of product is defined as the quantity of metal used per unit of product manufactured during a year. This ratio measures the efficiency of converting a ray material into final products. The material composition of product has shown steady and persistent declines over time for most metals and materials. This tendency demonstrates the continued improvements in manufacturing technology, resulting from substitutions of other materials and improvements in production efficiency. The purpose of this paper is to study trends in the material composition of product to reveal the impact of advanced materials on the use of traditional metals.

Jan 1, 1990

By N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities for the year 2015 draws upon information from industry sources, published literature, SNL Metals & Mining (SNL) (Charlottesville, VA) database and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry, and presents analyses of exploration activities performed by the mineral industry.Three types of information are reported and analyzed in this annual review of international exploration: budgetary statistics expressed in U.S. dollars provided by SNL; regional and site-specific exploration activities that took place in 2015 as compiled by the USGS; and regional events that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources were used to develop commodity and regional compilations, statistics may vary depending on the source and type of data that are being reported.The SNL data summarize planned company budgets for worldwide exploration activities in 2015 for 24 nonfuel mineral commodities and metal alloys and are based on company surveys. Surveys focused on precious metals (gold, platinum-group metals and silver), base metals, (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (bauxite, chromite, iron ore, manganese, phosphate and potash), and other commodities (diamond, graphite, heavy-mineral sands, lithium, niobium, rareearth elements (REE), tantalum, tungsten and uranium).USGS data compilations and analyses are based on information provided by USGS mineral commodity and country specialists, as well as industry contacts and published trade journals. The USGS data summarize exploration site data collected for more than 80 minerals and materials, with a focus on base metals, diamond and precious metals. The USGS analyzed available information to assess the level of exploration activity in 2015 and to report trends in mineral exploration activity for the period 2005 through 2015. These analyses identify where mineral exploration is occurring by commodity and region and the intensity of activity that is taking place in each region for selected mineral commodities, and determines those factors that most affect changes in exploration activity."

May 1, 2016

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971

By M. Morrongiello

The Kalgoorlie Consolidated Gold Mines Fimiston Open Pit is mining through a dense network of disused level workings and stopes of varied sizes and orientations. This study investigated the interaction between underground workings and the pit slope stability, in particular for the ultimate pit depth of over 600 metres. Parametric analyses were conducted on the structural and rock mass properties in order to provide realistic input. Several cases in both 2D and pseudo 3D using UDEC were modeled and analyzed to investigate the performance of the rock mass at various mining stages. The concept of equivalent property factor was also introduced to model the 3D behavior using 2D models. Based on the modelling results, the possible failure mechanisms and deformation of the pit walls were assessed. Factors of safety have been derived for the pit slope at different mining stages using the strength reduction technique. The modelling results agree well with pit performance monitoring results to date. The concept and results presented in this paper could be a useful reference for operations with similar circumstances and stress regimes.

Jan 1, 2005

By Joseph P. Sobanski, Michael P. Bruen

The North Branch tunnel segment of the Tunnel and Reservoir Plan Mainstream System consists of 14,075 m (45,885 ft) of 9.2 m (30.2 ft) finished diameter and985 m (3,232 ft) of 2.5 m (8.25 ft) finished diameter concrete lined rock tunnels. The TBM mining and concrete lining methods used in completing this $166million project differed from “typical” TARP construction methods in that a two-stage concrete lining was placed and the lining was initially placed concurrently with TBM mining as a two pass system in the same tunnel segment. For the main tunnel (9.85 m diameter), TBM mining averaged 24 m/day (79 ft/day), excluding downtime associated with two main bearing changes, and the concrete lining placement, averaged 117 m/day (380 ft/day) and 53 m/day (174 ft/day) for the invert and arch segments, respectively.

Jan 1, 1999

By John M. Arnold

Several years ago it became apparent to some of our people that; there was developing a very definite need for largee coal reserves in the West to satisfy- the need for fuel for the furnaces of electric generating plants with the rapid development of, the West, of both population and industry, it was impossible for hydro-electrics plants to keep up with the ever increasing demand for electricity. In 1960, Mr. E. R. Phelps, then associated with the engineering department of Peabody Coal Company, began a search for and development of coal deposits in the very remote northeast section of Arizona near the village of Kayenta. Travel to this section of the country was not easy even at this late date, and it was an eight hour drive from Farmington, New Mexico to Kayenta, Arizona, a distance of some 130 miles. The trip was over roads that even' a-horse and wagon had trouble negotiating and a four wheel drive vehicle was about the only type of transportation that could satisfactorily traverse these roads, as testify many badly beaten sedans and coupes that tried it. Since that time a very excellent road has been constructed from Shiprock; New Mexico to Cameron, Arizona where it junctions with another excellent road that runs north to Page, Arizona and the Lake. Powell area and south to Flagstaff, Arizona on highway 66. Kayenta is a small village nestled at the foot of the Black Mesa near its northeast extremities. The coal deposits of interest were on the surface of the mesa. This location presented another problem, as the only trail to the top of the mesa was intended for walking, horseback, or a brave soul In a horse and wagon. Once again the four wheel drive vehicle was about the only answer. To reach the coal deposits you must climb the mesa, which is vertical ascent of some 1,500 feet, and then proceed southward into the bowl of the mesa with an ensuing descent of some 1,000 feet, finally coming to an elevation of 6,500 feet, at which elevation the coal outcrops become apparent.

Jan 1, 1969

By K. Ananthpadmanabhan

Hydrolyzable surfactants such as fatty acids and amines undergo, in addition to micellisation and precipitation, various associative interactions in aqueous solutions to form ion molecular complexes such as acid-soap, dimers etc. depending upon the solution conditions such as pH. The interaction of these collector species with the mineral surface and with other dissolved species in solution will play a significant role in determining the interfacial processes such as adsorption and flotation. Marked differences in the hydrophobicity imparted to the mineral surface depending upon the solution conditions such as Ph can be attributed to possible differences in surface activities of the above complexes. This aspect of solution chemistry of flotation systems is discussed here for two widely used collectors namely, oleic acid and dodecylamine. Equilibrium species distribution diagrams based on the available literature .data and on estimates of energy of interactions between molecules, have been obtained for oleic acid and dodecylamine solutions.

Jan 1, 1978

By Caibin Wu, Bin Xie, Jiaqi Tong, Ningning Liao, Chong Zeng

Understanding the energy-size reduction relationship is vital to grinding process; therefore, this paper aims to show the energy-size reduction of magnetite-calcite binary mixture in a laboratory wet conical ball mill. Single magnetite, single calcite, and blended magnetite-calcite mixture at three weight ratios in four particle sizes were ground in a laboratory wet conical ball mill at four grinding time periods. The results showed that the particle size distribution of both fine particles and coarse particles of single and mixture ground product fitted well with the PSD computed by Rosin–Rammler-Benne function. The larger mass percentage of calcite is, the higher t10 of binary mixture ground product is. On the contrary, t10 in the mixture decreases as the percentage of magnetite in the mixture increases. The different breakage behaviors in blended samples are due to the hardness and particle size. The results of calculated ratio of energy absorption factor showed that the calcite consumed more energy in the breakage process of binary mixture than ground alone. The JK size-dependent breakage model based on the t10 method fits all the experiment data, be it generated from pure minerals, mixtures at different weight ratios, or each component separated from the mixture.

Jun 4, 2022

By Nikhil Dhawan, Sanjay Pindar

The limited lifespan, ever-growing demand, and significant lithium and cobalt content are responsible factors for the immediate recycling of discarded lithium-ion batteries. Discharged batteries were dismantled, segregated, and size reduced to recover cathode and anode material. The active cathode material comprises LiCoO2 (65.8%) and LiMn2O4 (34.2%) and was carbothermal reduced with recovered graphite in a microwave furnace followed by water leaching and magnetic separation. A Box Behnken statistical experimental design is used for process optimization. Both cobalt and manganese report to magnetic fraction, whereas graphite and lithium carbonate report to non-magnetic fraction and solution crystal respectively. The final product comprises of cobalt 73% and manganese of 14% with process yield of 36% and saturation magnetization of 76 emu/g.

May 16, 2020