Search Documents

By C. D. Harrison, J. W. Parkinson

This paper compares the ash slagging potential of Illinois No. 6 seam coal as raw coal, as commercially cleaned coal processed in a baum-jig plant, and as coal cleaned to a reduced ash specification at the Electric Power Research Institute's (EPRI) Coal Cleaning Test Facility. The comparison is based on ASTM ash fusibility data, a slagging index, gravity fractionation analyses of critical mineral matter compounds, and comparative pilot combustion tests. The first three grounds of comparison are laboratory data. The final comparison involves burning about 13.6 t (15 st) of each coal at Conoco's 4.40-kW/h (1.5 million-Btu per hr) test combustor. The evidence of these four comparisons indicates that lowering the ash specification of coal before combustion can significantly improve the ash slagging characteristics of Illinois No. 6 seam coal.

Jan 1, 1987

By David R. Hargis

Large-scale groundwater withdrawals are necessary to depressurize a confined aquifer system allowing the dry open-pit mining of the overlying phosphate ore. The extent of the existing and planned groundwater development led to the establishment by the State of North Carolina of Capacity Use Area No. l. Groundwater use in the Capacity Use Area is regulated by a permitting system. A two-dimensional finite-difference ground- water flow model was developed for North Carolina Phosphate Corporation. The aim of the model is to aid the Corporation in matters relating to permitting by serving as a predictive tool. The model can be used to project regional water level impacts resulting from various scenarios of depressurization pumping.

Jan 1, 1983

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

The main aim of this work is to evaluate whole-body vibration (WBV) of dozer operators based on three sitting postures (i.e., with 15° lean forward inclination posture, vertically erect posture with no inclination, and with 15° lean backward inclination posture) in Indian surface coal mines. A seat pad tri-axial accelerometer was used to collect WBV data from six dozer operators for three different sitting postures. Results showed that except for Dozer-1, 2, 4, and 5 operators during lean forward sitting posture and Dozer-4 operator during vertical erected posture, no other dozer operators have exceeded an exposure limit value (ELV) of 1.15 m/s2 in any of the considered sitting postures. Similarly, the vibration dose value (VDV) based on exposure action value (EAV) of 9.1 m/s1.75 has surpassed for all the dozers. But no dozer operator has exceeded an exposure limit value of 21 m/s1.75. The outcome of the study infers that based on “above health guidance caution zone (HGCZ)” for daily vibration exposure, i.e., A(8) measurements, for the operator sitting in lean backward postures the vibration amplification was reduced by 32.89% less compared with lean forward posture and 16.23% less when compared with vertically erected posture. Similarly, based on VDV(8), the exposure to vibration for the lean backward posture was reduced by 33.34% when compared with lean forward posture and 17.11% less when compared with vertically erected posture. Based on the above observation, it is concluded that lean back inclination with a trunk flexion of 15° is a favorable sitting posture, as it exposes the dozer operators to minimum vibration.

By S. Hamm

Elevated total dissolved solids (TDS) content in waters downstream from surface coal mines in Central Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and ICP-MS was used to determine how leaching conditions affected release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that, for certain spoil materials, SC in leach column effluent was effectively reduced when spoil was leached first with acidic rainwater followed by ambient rainwater (vs. ambient rainwater leaching alone). This suggests that accelerated leaching might aid in long-term stabilization of some materials.

Feb 23, 2014

By S. P. Winkelmann

The expansion in gold production in the Carlin 'Trend over the last few years has been one of staggering proportion. To increase gold production while minimizing capital requirements and providing for the safe and efficient mining and processing of ores has required a tremendous effort by the Mine Engineering group at Newmont Gold. This paper discusses the organizational changes implemented to effectively deal with a full range of engineering problems and how the Newmont Gold Mine Engineering group dealt with these problems. Specially developed computer software and their applications will be explained. Improvements in the techniques used in converting geologic resources into reserves, and in scheduling the mining of multiple pits to feed multiple processing facilities, as well as ore control procedures are presented. Current mine engineering practices are discussed.

Jan 1, 1990

By A. J. Basu

Geotechnical design plays a key role in mine design. I A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches I) judgmental, based on observational and experiential facts, 2) empirical, based on empirical design formulae, and 3) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools was addressed earlier (Basu and Kuruppu, 1995). The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing structures applicable to mining geomechnics. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis application in excavation design.

Jan 1, 1996

By Alfred G. Hoyl

The author, in exploring a virgin area vertically in two known ore shoots requiring decline shaft sinking, drifting, crosscutting and diamond drilling, chose to use electric, electric hydraulic, and diesel rubber-tired equipment. A rebuilt hoist, and electric hydraulic shaft shovel (mucker), hydraulic sinking drills, single boom electric hydraulic jumbo, electric hydraulic LHD, and electric hydraulic diamond drill were used successfully. Slides of the equipment and its use are shown. The advantages and disadvantages of the equipment are discussed, together with costs and production.

Jan 1, 1984

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner?s cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutterhead, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head?s effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner generally improved air quality at both sampling locations to varying degrees in some, but not all, mines when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By D. D. Schlepp

There is a continuing debate about the influence of circulating load and classifier efficiency on the capacity of the circuit. Specifically, the effects of preferential classification, bypassed fines, and the sharpness of classification will be examined. Horizontal cyclones have also proven to be very successful in a number of operations but their impact on the circuit capacity has not been clearly defined.

Jan 1, 1990

By S. K. Nicol

The results of column flotation tests conducted on a bulk sample of ultrafines discarded from the fine coal desliming cyclones at the Riverside coal preparation plant of Theiss Dampier Mitsui Coal Limited are presented. A 9% ash concentrate was obtained from a 51% ash ultrafine feed at 75-80% recovery of combustibles in a single stage of column flotation. From this result it is predicted that installation of column flotation at Riverside would lead to the annual recovery of additional coal worth $US5.1M. The operating conditions for coal and copper column flotation are compared and some differences which may result in a variation in column design are noted.

Jan 1, 1987

By C. L. Lin

The characterization of rare-earth resources in 3D is now possible using high-resolution X-ray microtomography (HRXMT) to describe ore texture and mineral phase composition. In addition, detailed texture analysis, including grain exposure and mineral association, can be described. Preliminary examination of a sample of Mountain Pass ore is reported to describe the spatial distribution of the mineral phases (calcite, barite and bastnaesite), particularly the grain size distribution of bastnaesite. The examination includes analysis of selected particle size classes to determine the appropriate size for liberation of the rare-earth mineral bastnaesite. Good liberation is expected to be achieved if the material is ground to a top size of -150 µm.

By R. G. Reddy

Viscosities of Feo-SiO2 slags were calculated using the previously developed structural based model. An expression was derived using hole theory and the atomic pair model to relate the NO0 and temperature to the viscosity. The deduced equation n=4.9x10-9 T1/2 NO0 exp (E/RT) poise was successfully applied to predict the viscosity of FeO-SiO2 slags in the composition range of 0.1 < XSiO2 < 1 for several temperatures. The calculated data agrees well with the experimental viscosity data.

Jan 1, 1991

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By Meng Li, Hao Nie, Weitian Ding, Mamdouh Omran, Ying Li, Yao Ge, Yaowei Yu, Abourehab Hammam, Lei Zan

This study examines the isothermal and non-isothermal reduction behaviors of iron ore compacts in a pure hydrogen atmosphere and compares the results obtained during the reduction process by CO. The different phases accompanying the reduction reactions were identified using X-ray diffraction (XRD) and its morphology was microscopically examined. In isothermal experiments, temperature plays a significant role in the reduction process. At any given temperature, the reduction rate during the initial stages is higher than that during the final stages. The reduction rate in H2 atmosphere was faster than in CO gas. The comparison of activation energy values suggested that reduction with H2 is more efficient thanwith CO. At the same temperature, the time required to achieve a certain degree of reduction was lower when using H2 gas than CO atmosphere. In non-isothermal tests, the heating rate has a significant effect on the reduction rate and reduction extent. At the same heating rate, the degree of reduction was higher in H2 atmosphere than in CO gas. Based on experimental data, the parameters of reaction kinetics were deduced by application of model-free and model-fitting methods. The reduction in H2 atmosphere was controlled by nucleation model (Avrami-Erofeev model), while the CO reduction reaction was controlled by gas diffusion.

Sep 29, 2020

By R. D. Wunder

The Chino Mines Company, a Kennecott-Mitsubishi partnership, located in Hurley, New Mexico, recently completed a $405 million modernization of its mine, concentrator, and smelter facilities. The mine/ concentrator modernization commenced in 1980 and the smelter modernization began during 1982. Modernization of the mine and concentrator facilities involved increasing the mining rate from 98 kt/d (108,000 stpd) to 152.2 kt/d (167,800 stpd). Ore mining was designed to increase production from 20.2 kt/d (22,300 stpd) to 34.0 kt/d (37,500 stpd). A new concentrator was constructed near the mine using semi-autogenous grinding. The new smelter uses the INCO flash smelting process, increasing capacity by 40.8 kt/a (45,000 stpy) to 99.8 kt/a (110,000 stpy) of salable copper.

Jan 1, 1985

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented. Applications in the industrial plant and in the research field are discussed.

Jan 1, 1990

By K. V. Raj, T. Bhowmick

"The control of fugitive dust in high-latitude openpit mines is challenging due to unique atmospheric phenomena resulting in complicated flow regimes as well as atmospheric inversion due to the lack of adequate insolation during prolonged winter seasons. In this study, two idealized (one conical and one trapezoidal) three-dimensional openpit mine geometries were simulated for different seasonal conditions using a computational-fluid-dynamics package from Software Cradle. The airflow was solved by Reynolds-averaged Navier-Stokes equations using the standard kappa-epsilon turbulence model. The concept of particle tracking was used to predict the flow patterns of dust particles. For various climatic conditions and two different pit geometries, fugitive dust particles varying in size, from PM0.1 to PM10, and concentration were generated at various locations and dispersed by the airflows inside the openpit mine. The amount and location of dust particles inside the pit were reported at various time intervals. In the summer season, airborne dust particles were quickly transported outside the openpit domain. In the winter season, however, the development of atmospheric inversion significantly affected the amount of dust retention inside the openpit domain. IntroductionThe computational-fluid-dynamics (CFD) modeling of openpit mines is challenging. In a recent paper (2015), we presented different constraints and challenges in developing a three-dimensional CFD model. In order to obtain realistic results from a simulation, however, appropriate values of various inputs are required. The simulation results of a three-dimensional nonhydrostatic model by Shi et al. (2000) showed that both the mechanical and thermal forces are important mechanisms, controlling the development of the atmosphere inside an openpit mine. Alvarez et al. (2007) used a CFD model for predicting dust dispersions in a medium-sized limestone quarry, and presented several iso-surfaces of varying dust concentrations using ANSYS CFX. A similar study by Torno et al. (2010) introduced a more sophisticated parameterization of the dust sources. Flores et al. (2014) used an OpenFOAM CFD simulation package to simulate and predict pollutant dispersion in an idealized and an actual openpit mine in Chile with an intense insolation condition. The model was simulated for three different conditions: (1) air-advection (10 m/s, or 33 ft/ sec)-driven mechanical turbulence, (2) surface-heat-flux (240 W/m2, or 76 Btu/ ft2-h)-driven thermal buoyancy and (3) both air-advection- and surfaceheat- flux-driven conditions. The results of the simulations showed that the buoyant currents contribute to the removal of a large percentage of the dust particles. The buoyant currents modify the purely mechanical-turbulence- induced flow pattern and reduce the particle residence time, commonly observed in a purely mechanical turbulent flow (nonbuoyant case)."

Jan 1, 2015

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

The Jiboia heavy mineral sands deposit is a new discovery associated with the São Francisco River delta on the northern coast of Sergipe state. The identified resources are part of the much larger mineralized trend. Mineralization is hosted in paleodunes deposited on Holocene marine terraces (Fig. 1). The dunes are up to 30 m above sea level, and mineralization occur from 6 m above sea level upward. The main ore minerals constitute pseudorutile, ilmenite, zircon, rutile and monazite. This work presents a thorough characterization of the mineralogy and granulometric distribution of the Jiboia orebody.

Apr 1, 2024