Search Documents

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014

By H. W. Gao

During the last decade, the feasibility of applying the in situ leaching technology to the recovery of copper from deeply buried deposits containing chalcopyrite has received much attention.(1-4) The major incentive for using this technology is that under certain circumstances, copper in deep underground deposits, which cannot be mined economically by conventional means, can be recovered economically. Basically, this technology involves rubblization of the deeply buried copper ore body followed by in-place leaching of the rubblized copper ores. Rubblization of the ore can be achieved by some suitable method such as the use of block caving mining. The rubblized chimney is then filled with water until the original water level is reached. Leaching occurs when the eater saturated with oxygen is introduced into the chimney- and flows through the fractured rock masses and within pores of rocks. As the dissolved oxygen oxidizes the primary sulfides, heat is generated. Because of low conductivity of the surrounding rocks, the generated heat is able to raise the temperature of the chimney. The increase in the temperature of the chimney and the relatively high content of dissolved oxygen in the leach solution under high hydrostatic pressure will result in an enhanced dissolution of the primary sulfide minerals. To ensure a successful application of the in situ leaching technology, a complete understanding of the effects of the ore particle size distribution, ore grade mineralogy, temperature, pressure, lixiviant concentration, pH, etc. on the rate of copper recovery is necessary so that copper can be recovered efficiently and the amount of copper extracted can be predicted. These can be achieved through mathematical modeling of the in situ leaching process and conducting laboratory tests. In this paper we will present a mathematical model that simulates the in situ leaching process as depicted in Figure 1. To model this process properly, not only the 'kinetic and thermodynamic aspects of leaching chemistry must be known, but the effects of heat generation, the physical aspect of fluid flow and other related multicomponent transport phenomena must be considered. Furthermore, since most factors involved in the leaching process change with time, a leaching system must be described using unsteady state equations.

Jan 1, 1981

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluated the effect of bucket orientation and operating parameters on resistive forces and penetration for rubber tire loaders. The work used a 1:16 scale LHD model to test a rubber tire loader (RTL) bucket operating at different levels of tractive effort, speed, digging height, and rake angles in a full factorial design experiment. The work repeated the test on two different muck piles with different particle sizes and used generalized regression modeling to test the association of rake angle, tractive effort, speed, and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort, and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle, and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The observation that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces is a novel contribution that enhances our understanding of RTL loading. The results also show that the effect of speed, tractive effort, and height above the floor all change with changes in particle sizes. This work adds to the literature on the effect of rake angle, height above the floor, tractive effort, and speed on penetration and resistive forces for rubber tire loaders.

Aug 24, 2020

By Todd Clarke, Ralf Winterberg

For more than a decade the tunneling industry has explored the potential and benefits of macro synthetic fiber (MSF) reinforced concrete solutions for precast tunnel segments. Parallel to industry investigations, academic research is being undertaken to better understand this material when subjected to the typical loads expected during mechanized tunneling. This paper investigates the performance of MSF reinforced precast concrete tunnel segments by means of an experimental program comprising testing of full-scale tunnel segments. The presentation of the satisfactory results of the experimental testing regime will be complemented by a brief case history from a successfully executed project—an America’s First.

Jun 13, 2021

By M. Misra, I. A. H. Schneider

The flocculation of -38 pm calcite, hematite and kaolinite aqueous suspensions by the yeast Candida parapsilosis and products derived from rupture of the microorganism was studied. Flocculation of hematite suspensions by the microorganism and its derivatives readily takes place between pH 2.8 and 11.4. Maximum flocculation occurs at about pH 6.5. Flocculation of calcite suspensions by the microorganism and its derivatives readily takes place between pH 7.0 and 11.8. Maximum flocculation occurs at about pH 10.0. Flocculation of kaolinite suspensions was less than that for the other two minerals. However, a soluble fraction derived from the rupture of the organism functioned as a good flocculant for the mineral, albeit at an increased concentration, between pH 2.6 and 11.5. Maximum flocculation occurs between pH 6.8 and 7.2. An attempt is made to relate the behavior of the various systems to the surface characteristics of the minerals and the surface and chemical properties of microorganism and its derivatives. Experimentation used to evaluate the flocculation includes actual flocculation tests, microelectrophoresis measurements and scanning electron microscopy.

Jan 1, 1994

By J. G. Groppo, A. E. Bland, B. K. Parekh, W. F. Stotts

Many coal preparation plants discard fine coal (generally minus 100 mesh) because it is difficult to beneficiate economically. At the Kentucky Energy Cabinet Laboratory (KECL), the waste streams from several Kentucky preparation plants were evaluated for cleaning with counter-current column flotation. A series of performance evaluations were conducted using a 0.05 m (2 in.) internal diameter (I.D.) 7.9 m (26 ft.) high laboratory column. The objectives of these tests were to assess the performance in terms of recovery and percent ash in clean coal and to optimize the operating parameters relative to combustible recovery and grade. Refuse streams containing 30-50 percent ash were upgraded to 2-8 percent ash with Btu recoveries of nearly 90 percent. A pilot scale column flotation cell was installed at the Bell County Coal preparation plant. This pilot plant utilized a 5.79 m (19 ft.) high and 0.15 m (6 in.) I.D. column to verify the performance data of the 0.05 m (2 in.) I.D. column for two different waste streams. Performance evaluation and pilot plant testing results related to scale-up are discussed.

Jan 1, 1988

By G. Bylapudi, A. Bhagwat, K. Mondal, A. J. S. (Sam) Spearing

Minimizing the effects of corrosion improves the long-term performance of the rock anchors and ground control systems in underground mines, which is fundamental for safe operation over the design period. The primary objective of this study is to explain the problems due to stress corrosion cracking (SCC), strain-induced corrosion cracking (SICC) and other forms of corrosion, and why the mining industry’s ground control professionals should take this into serious consideration. It is important to clearly determine the kind of SCC mechanisms that causes roof bolt failures in order to suggest the necessary action plan to mitigate or eliminate the possibility of the cause. Pertinent literature and studies around the globe on this complicated subject are reviewed. The secondary objective is to encourage the use of corrosion-resistant ground control products in the underground mining industry in areas of high corrosion potential. Characteristics of SCC on high strength steel are also reviewed. The literature and preliminary studies to date indicate that research work is necessary in United States.

Jan 1, 2015

By Ahmet Tezcan, Zeki M. Dogan, Yalçin Kaytaz

Autogenous grinding in Turkey was first applied to quartzite where the mill is grate discharge type with an internal diameter of 2.99 m, having a length of 3.20 m and a capacity of as to 11.0 tons per hour. The second autogenous grinding was applied to a copper ore at Murgul Cakmakkaya Flotation plant of (KBI) Black Sea Copper Works having three mills 26 feet in diameter and 10 feet in length in close circuit with hydrocyclones. Recently, alterations were made in grinding circust by adding pebble mills. Furthermore, rubber liners and lifter bars were introduced pebble extractor and classifier were new features in the primary mills and circulating load was reduced by 20-50 tons per hour. At the end of these charges, capacity of each mill line was increased to 48 tons per hour with a full capacity of more than 9000 tons per day. Thirdly, autogenous grinding has been executed successfully on the slags of Samsun Smelting Plant of (KBI) Black Sea Copper Works with a mill of 20 feet in diameter and 6 feet on length having pebble mill following autogenous grinding.

Jan 1, 1992

By Rudolph K. Hoagberg

Silica sands, primarily in coarse size ranges, are used to prop open fissures or voids created in the bedrock by hydraulic fracturing. This procedure increases the flow of gas or oil or other fluids through the bedrock. The sands used must meet various specifications relating to their physical and chemical characteristics; these characteristics are in turn related to the geologic provenance of the sand deposit. The Jordan Sandstone, a Cambrian formation which is exposed in Minnesota and Wisconsin, meets the specifications of a proppant sand by virtue of its depositional history and its sedimentary properties.

Jan 1, 1980

By T. Karalis

Perlite is a generic term for naturally occurring siliceous rock. It is a form of natural volcanic glass the main constituent of which is amorphous silica (70-76%). Perlite, when heated rapidly to its softening temperature range, expands from four to twenty times its original volume, due to the presence of 2-6% ?combined? water, in a manner similar to popcorn as the H2O molecules vaporize and create countless tiny bubbles, which account for its exceptional physical properties: light weight (30-150 kg/m3), low thermal conductivity, cellular structure, in general. These properties make perlite adaptable for numerous end-uses, which can be distinguished into 2 categories: Expanded perlite applications in: a) Construction Materials market (e.g. Acoustical Tiles, light-weight insulating Mortars, self-levelling Concrete), b) Agriculture (e.g. Hydroponics), c) Food and Chemical industry (e.g. Filtration Media, Filler, etc.), d) Insulation and Heat resistance technology (e.g. Cryogenic vessels, Refractory Bricks, etc.). Unexpanded Graded perlite applications in: a) Phosphoric Fertilizers industry (additive in H3PO4 production), b) Foundry technology (slag-aid, insulating and heat resistance agent).

Jan 1, 2006

By K. M. Mohamed, R. K. Zipf

The shear strength properties of generic cement foam material and cement foam/concrete interfaces were examined at three testing scales. In laboratory direct shear tests on specimens with average shearing area of 0.006 m2 (10 in.2), the cement foam material had average peak and residual shear strengths of 0.88 MPa (128 psi) and 0.39 MPa (56 psi), respectively. Depending on the concrete strength, the cement foam/concrete interfaces had peak and residual shear strengths ranging from 0.71 to 0.81 MPa (103 to 117 psi) and from 0.27 to 0.29 MPa (39 to 42 psi), respectively. In laboratory direct double shear tests on specimens with average shearing area of 0.084 m2 (130 in.2), the cement foam/concrete interfaces had average peak and residual shear strengths of 0.17 to 0.30 MPa (25 to 44 psi) and of 0.11 to 0.23 MPa (16 to 33 psi), respectively. In large shear tests of simulated cement foam seals with the Mine Roof Simulator (MRS) test frame, cement foam/concrete interfaces with shearing area of 1.486 m2 (2,304 in.2) had average shear strengths of about 0.08 and 0.16 MPa (11 and 23 psi) along the roof and floor interfaces, respectively. The average shear strength through the cement foam material was 0.38 MPa (55.3 psi). Finite element analysis of the large seal tests and the back analysis of the shear strength of full-scale cement foam seals conducted at the NIOSH Lake Lynn Laboratory confirmed shear strength of about 0.14 MPa (20 psi) along the seal/rock interfaces. The study concluded that the structural analysis of cement foam seals should be based on their residual shear strength determined from small laboratoryscale tests of the cement foam/concrete or rock interface and not be based on their peak strength.

Jan 1, 2014

By J. Iannicelli

Kaolin, normally an inert filler when compounded with polymers, is converted into a strongly reinforcing pigment by prereaction with certain functional silanes. Modification of kaolin with amino and mercapto silanes allows it to form crosslinks and confers significant improvements in modulus, abrasion resistance, compression set and other physical properties of a broad range of polymers.

Jan 1, 1990

By D. M. Hausen

Carbonaceous gold ores are ubiquitous to virtually all of the Carlin-type gold deposits along the Carlin gold belt in north central Nevada, representing the unoxidized "zones" of presumably extinct thermal spring systems of mostly Tertiary age. A period of subtropical weathering resulted in deep sub-lateritic zones in most deposits to several hundred feet below surface. Carbonaceous ores below this supergene profile of weathering have been investigated by various methods, including petrographic study, standard geochemical and organic carbon analyses, carbon and hydrogen isotopic ratios, electron-spin resonance spectra, infrared spectra, and DTA techniques. Results have been integrated with recent findings by other investigators utilizing fluid inclusion and thermal brine data to indicate a first phase hydrothermal solution temperatures and pressures at a minimum depth of 6 km under normal geothermal gradient. This phase resulted in the quartz-barite-calcite vein filling of the host rocks. Gold mineralization took place later at shallower depths. Primary organic material in carbonaceous ores from the Carlin and other mines appears to be a pyrobitumen residue derived from an old oil pool that had been heated by the thermal solutions, and from which the light hydrocarbon fractions were removed. Some of the bitumen was remobilized along silicified veinlets in the ore, but its role in the emplacement of the gold, itself, is not clear. The gold was localized submicroscopically in fine pyrite, mostly in framboids, and as fine metallic particles, but does not appear to be concentrated within the carbonaceous matter per se. However, reducing conditions associated with bituminous residues are believed to have been favorable for gold deposition.

Jan 1, 2013

By Carl Erickson

The term shortwall mining is somewhat of a mis¬nomer. It may infer a longwall mining system, but of much shorter face length. Actually, continuous pillar mining is a more descriptive term. Coal is mined using a continuous miner as would be done in pillar extrac¬tion, but with the addition of roof supports to control the caving. Face length on such a system typically is 46 to 61 m (150 to 200 ft). The coal is cut in front of the roof supports in the same direction as with a long¬wall shearing machine or plow, but it is mined with a continuous miner and shuttle cars of the same type as used in continuous mining. ROOF SUPPORTS Roof supports for shortwall mining must be con¬siderably larger than those used for longwall mining because of the additional roof to be supported by the wider 2.6- to 3.4-m (81/2- to 11-ft) cut of the continuous miner. Capacities of shortwall chocks in current use vary from about 454 to 726 t (500 to 800 st). The higher capacity as compared to longwall roof supports is needed primarily because of (1) the greater support length, hence more roof weight, and (2) the presence of draw slate in the eastern coal seams, where shortwall is being used. The most popular shortwall support currently used is the four-leg 590 t (650 st) model. This support is shown in Fig. 1. The price of this support is approxi¬mately $25,000 each. As shown in Fig. 1, the shortwall chock incorporates an unusually long forward bar that has an additional hydraulically operated extension bar to provide face support for the wide miner cut. METHOD OF OPERATION Mining Sequence In shortwall mining, two or three (depending upon the chock design) move up cycles of the chock are needed because of the miner cut width. Fig. 2 depicts the five steps required to complete the move of chock and spill plate using a miner that takes a 3.3-m (10-ft,

Jan 1, 1982

By Zibo An, Yong Hu, Hao Zhang, Hong Cao, Jun Xue, Zhen Luo

Phosphogypsum (PG) is a by-product of solid waste produced by the phosphate chemical industry. Owing to large emissions and massive storage issues, it causes a potential threat to our environment. Hereby, a method based on the precipitation and crystallization properties of calcium phosphate-magnesium ammonium phosphate (CP-MAP) followed by its adsorption on active solid waste powder is used as the main principle to treat PG harmlessly. The treatment process and its influencing factors for orthogonal experiments along with the associated environmental safety have been studied in detail. The results showed that this method could simultaneously remove soluble phosphorus and soluble fluorine from PG. When ACP, FA, HBM, and Ur were added to PG at a dosage of 3%, 13.5%, 0.04%, and 0.04%, respectively, the residual phosphate and fluoride contents was 0.061 mg/L and 0.856 mg/L respectively in the PG leaching solution. Compared to state-of-the-art approaches, this method exhibited higher efficiency in removing phosphate and fluoride. Most importantly, this method does not cause any secondary pollution in the process, thereby showing a novel application in large-scale industrial treatment.

Aug 29, 2022

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By A. Noble

"Linear circuit analysis (LCA) is a fundamental tool that may be used to evaluate, design and improve the performance of mineral separation. The traditional LCA methodology provides a comparative evaluation of circuit designs purely from the unit interconnections. The quantitative approach uses the analytical circuit solution to evaluate the slope of the circuit’s partition curve at the midpoint. Since the partition slope is often associated with a separation’s general selectivity, this numeric value is used to compare and rank alternative configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. By itself, this value does not account for the relatively high unit dollar value of pure material or the gains and losses in mass yield associated with alternative circuit configurations. Realizing the value in the LCA methodology, but respecting the limitations of the partition slope valuation, the authors have derived two new performance indicators that quantitatively address pure particle misplacement (the Partition Moment of Inertia) and circuit mass yield (the Yield Score). Together, these parameters provide a better indication of separation economics in typical mineral and coal separation systems. Since the two parameters provide independent information on circuit selectivity and circuit yield, a Pareto efficiency, multi-objective function selection approach is proposed for preliminary circuit selection.IntroductionOver the past 30 years, numerous scientific and industrial studies have proposed various mineral processing circuit design methodologies that attempt to optimize the allocation of separation resources within the processing plant. Over this period, the methodologies have undergone various transitions, including the increased inclusion of process models and computationally intensive algorithms, as well as a general shift from a purely technical solution (Lauder and McKee, 1986) to partially economic solutions (Abu-Ali and Sabour, 2003; Cisternas et al., 2014). Today, circuit design is largely driven by flowsheet simulation; however, no consistent design methodology is used across the industry.One intriguing approach for circuit evaluation is linear circuit analysis (Meloy, 1983a). This method evaluates the separation potential of the circuit solely considering the unit configuration and stream interconnections. No preliminary data other than the basic circuit configuration is required to use the approach."

Jan 1, 2015

By H. R. Manouchehri

In flotation practices, as particles become finer, such as smaller than 20 μm, process efficiency declines markedly. Selective agglomeration of fine particles is a technique to enhance the recovery of fine valuable minerals in flotation circuits. Different agglomerating methods have been introduced and tested. One method that has recently received much attention is to make use of magnetic force to aggregate fine particles. A selective aggregation of fine paramagnetic particles, such as sulfide minerals, can be achieved in the high-intensity magnetic field prior to or during flotation. The method is simple, selective and effective for fine particles and has low operational cost, though a minimum magnetic susceptibility for fine grains is required to promote the process. In this paper, the implementation of the ProFlote magnetic conditioning device in Boliden’s Garpenberg old concentrator in Sweden, where a complex massive sulfide ore is treated, is presented and discussed based on Boliden’s Garpenberg plant. The results showed an increase in the flotation recovery of fine valuable minerals. Zinc (Zn) production was increased by between 1,100 and 1,500 t/a, while salable yearly silver (Ag) production was increased by 1,500 kg. The copper (Cu) grade in the final concentrate was increased by 1 percent, while reductions in its Zn and lead (Pb) grades were obtained. Moreover, considerable reduction in Zn deportment to the final tail was observed

By Ernest M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger mines have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1983

By Richard A. Levins

The imposition of non-market regulations, such as the proposed SO2 standards for coal combustion, will typically lead to less efficient (thus more costly) production in a free enterprise system. For the coal industry these increased costs will occur in several ways, among which are mining less accessible low sulfur reserves and transporting low sulfur coal to distant markets. There are, of course, social benefits of reducing the S02 emissions from the use of high sulfur coal. The social benefits include decreased health risks, reduced damages to property, and certain unmeasurable benefits associated with the aesthetic appeal of clean air. Proponents of Federal S02 standards argue that the benefits gained from reduced emissions will exceed the costs borne by the coal industry and society in general in meeting the regulations. The purpose of this paper is to investigate the degree to which costs of meeting future energy demands from coal will change under different sulfur standards. No attempt is made to estimate the benefits of imposing regulations. Specifically, the impact of SO2 standards on the private costs of meeting regional coal demands, the competitive positions of the nation's major coal producing regions, the degree to which strip mining as opposed to underground mining will be feasible, the amount of coal being processed, and the amount of coal transported over major rail routes will be analyzed.

Jan 1, 1976