Search Documents

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Khaled Mohamed

Resin-grouted bolts serve as a crucial means of stabilizing yielded coal ribs in underground coal mines. A comprehensive investigation into their efficacy was undertaken by a collaborative effort between the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST). This study involved pull-out tests in multiple locations, including six coal mines and the NIOSH research mine. A total of seventy-three (73) tests were conducted, of wide range of anchorage lengths, ranging from a short encapsulation length of 0.305 m to a fully grouted encapsulation length of 1.524 m. The test findings indicate that when short encapsulation bolts are installed at high rotation speeds, their anchorage capacity is significantly reduced, leading to failure at the bolt-grout interface. Conversely, when these bolts are installed at lower rotation speeds, they exhibit greater capacity, with failure occurring at a higher anchorage load equivalent to the yield load of steel rebar. No matter what the rotational speeds were used during bolt installation in this study, the fully grouted bolts consistently experienced failure at the ultimate load of the steel rebar. Most of the tests carried out on partially grouted bolts with anchorage lengths of 0.610 - 0.914 m have shown behavior patterns like the fully grouted bolts, although exhibiting reduced stiffness. The outcomes of this research offer a profound insight into the ways in which resin-grouted bolts enhance the stability of coal mine ribs.

Feb 1, 2024

By M. Govinda Raj, S. Sridhar, M. Aruna

Hand-transmitted vibration (HTV) exposure is associated with various health risks for operators of mobile mining equipment (MME). The case–control research was conducted to determine the musculoskeletal disorder (MSD) risks associated with exposure to HTVs in the exposed (case) and non-exposed (control) groups. HTV readings were measured at the interface between the hand and the steering device using the SV 105B triaxial hand accelerometer connected to the SV106 human vibration analyzer involving 40 MME operators in accordance with ISO 5349:2001 guidelines. A questionnaire survey was also carried out among both the study groups using Cornell Musculoskeletal Discomfort Questionnaire. The European Union's 2002/44/E.C. was used to assess the health risks posed to the MME operators. Twenty-eight out of the 40 MMEs were generating HTVs exceeding the stipulated daily limits of vibration, putting 70% of the operators at increased risk for developing MSDs. The case group was found to have an elevated risk of exposure with odds ratio (OR) 7.56 (95% confidence interval (CI), 1.159, 49.39) and OR 12.80 (95% CI, 2.436, 67.285) times more likely than the control group to suffer discomfort in the left shoulder and left wrist, respectively, indicating increased risk of exposure to HTV. Additionally, cases had elevated risk associated with exposure to tobacco, OR 9.35(95% CI, 1.856, 47.129) compared to those who did not use tobacco. MSDs were more prevalent in the case group compared to the control group. This observation was validated by the field investigations and the responses of MME operators to the questionnaires.

Aug 2, 2022

By N. Iverson, E. Haft, V. T. McLemore, M. Woodard, E. Owen

Present and emerging technologies are renewing interest in domestic rare earth elements (REE) production. REE deposits throughout the North American Cordilleran alkaline-igneous belt are being re-examined for their economic potential. In New Mexico, the mineral deposits found in this belt are associated with Eocene–Oligocene alkaline to calc-alkaline igneous rocks. Four areas in New Mexico have been examined for their REE potential. The chondrite-normalized REE patterns are similar for all four districts, even though different REE minerals are found. Crandallite, xenotime, bastnäsite and brookite are found in fluorite veins and carbonatites at Laughlin Peak. Bastnäsite was extracted during fluorite processing from 1954-1980 from the Gallinas Mountains, where samples as high as 8% total REE are found in fluorite veins. Other REE minerals include agardite, parasite, xenotime, and monazite. Allanite, thorite and as much as 8133 ppm total REE are found in fluorite veins in the Capitan Mountains. In the Cornudas Mountains, exploration along the outer edge of the Wind Mountain nepheline syenite laccolith and within phonolite dikes, plugs, skarns and carbonate-replacement deposits in Chess Draw contain as much as 3110 ppm TREE, hosted in eudialyte, monazite, bastnäsite, and calciocatapleiite.

Feb 1, 2023

By Xinghai Lei, Nan Wang, Xiangyang Jin, Yuqi Ren, Yang Li

The upward mining method, as an effective mining method, is widely employed in close-multiple coal seams to extend the service life of coal mines and improve the recovery rate of residual coal resources. However, the upward mining feasibility of the upper coal seam is related to the height of caved zone of interlayer strata after lower coal seam extraction. Therefore, it is extremely important to determine the height of the caved zone after the lower coal seam. The No. 9 coal seam (upper coal seam) and the No. 12- 1 coal seam (lower coal seam) in the Qianjiaying coal mine are selected as the research object. The characteristics of the interlayer strata structure field, fracture field, and subsidence field are studied using UDEC numerical modeling, in which the height of the caved zone is gotten after the No. 12- 1 coal seam extraction. Furthermore, the height of the caved zone is verified by onsite detection of GPR and BTVI. In the numerical modeling, the height of the caved zone is 19.6 m. And the height of caved zone is 14.7 m and 15.4–21.2 m, respectively, by using the onsite detection of GPR and BTVI. The heights of the caved zone onsite detection results are consistent with the numerical modeling result. The No. 9 coal seam is always located above the caved zone after the No. 12- 1 coal seam extraction. Consequently, the upward mining of the No. 9 coal seam is feasible.

Jun 28, 2023

By Ben W. Burdett

The operation of an electrolytic refining tank house is an art as well as a science. If the electro-refining industry is to progress, a better understanding of the refining process is necessary. This would help to reduce the amount of training necessary to produce competent tank house operators who, in turn, would be able to increase both quantity and quality of the tank house product. To aid in understanding this process, quantitative relationships between the critical tank house variables must be established. The inherent major contributor to inefficiency in most tank houses is short circuits. By quantifying the effect of short circuits on each of the other variables in the system, as well as their effect on over- all system performance, better decisions regarding manpower allocation can be made. Current distribution under short circuit conditions, which has always been somewhat of a mystery, can be studied in detail. The relative importance of electrolyte balance, proper anode-cathode spacing, low contact resistance at points of electrical connection, and other system variables can be determined, With a better understanding of these variables, the steps necessary to increase current efficiency are more easily defined. Relationships between most of these variables are described in qualitative terms in the literature, but quantitative relationships between tank house variables have never been established. A realistic mathematical model of the tank house could be used to test the effect of variations in a single variable on other variables in the system, and thus define the quantitative relationships between tank house variables. It is not the purpose of this paper to establish these relationships, but to describe a recently developed model that can assist in their establishment. A computer program implementing this model has been applied to examine the effect of short circuits on overall current distribution. Some of the results are given here as examples of the utility of this program.

Jan 1, 1973

By R. Venugopal, V. K. Saxena, S. K. Tripathy

"This study was carried out to understand the impact of variation in material morphology on the efficacy of microwave pretreatment. Three different types of mineral matter – coal, iron ore and manganese ore – were treated with microwaves at different energy levels, from 180 to 900 W, for different time durations of one to five minutes. The treated samples were subjected to microscopic, milling and liberation studies. Coal is a porous and amorphous material with low dielectric constant, and grinding of the microwave-pretreated coal samples resulted in an 18.18 percent reduction in the 80 percent of passing particle size, or d80, and a 17.1 percent increase in carbon recovery. The microwave-pretreated soft and friable manganese ore samples showed a 47.82 percent reduction in d80 during grinding and higher manganese recovery of 42.46 percent during liberation analysis. The microwave pretreatment and milling of hard and banded iron ore reduced the d80 by 20.83 percent, but no improvement was observed in mineral liberation. Coal showed better results during treatment at lower energy levels of 180 W for one to three minutes, whereas the minerals needed higher energy of 900 W for five minutes. Particle size analysis indicated rapid size reduction up to an energy input of 25 Wh. This effect diminished with increased energy input.IntroductionComminution is an important unit operation in mineral processing plants for the purposes of size reduction and mineral liberation. But most comminution technologies are energy inefficient and only a small amount of energy is consumed in real size reduction, with the rest wasted. High-grade mineral resources have been exploited on a large scale for the last century, and the upgrading of low-grade resources is now required to fulfill the needs of industry. Pretreatment methodologies for comminution will play a crucial role in the upgrading of low-grade mineral resources. Researchers have studied various pretreatment methods to develop an energy-efficient and techno-economically viable solution to improve mineral liberation and product fineness with minimum energy consumption. Most of these studies were focused on the use of chemical additives, thermal, ultrasonic and microwave treatment, and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Gaete-Garreton, Vargas-Hermandez and Velasquez-Lambert, 2000; Wilson et al., 2006; Kumar et al., 2010; Wang, Shi and Manlapig, 2011; Singh et al., 2012)."

Jan 1, 2017

By M. Fan, Z. Long

"This paper presents some studies on recovering valuable elements from Chinese coal by-products, including coal combustion fly ash, stone coal ash, and coal flotation tailings. Both commercialized technologies and economic potential recovery methods are described in this study. Magnetically stabilized air-dense medium fluidized bed separation, tribo-electrostatic separation, froth flotation, and hydrometallurgical methods are discussed in recovering various valuable elements in Chinese coal by-products from different coalfields. These valuable elements include iron, carbon, aluminum, rare earth elements, lithium, gallium, germanium, uranium, titanium, scandium, silicon, vanadium and phosphorus, etc. The ultimate goal is to fully utilize all valuable elements in coal by-product. Each component within coal by-product should be efficiently segregated to its highest value. INTRODUCTION Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium, and phosphorus, etc. These coal-associated elements are significantly enriched in coal combustion by-product fly ash because of majority of main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main elements oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China, and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary widely due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides, and unburned carbon."

Jan 1, 2017

By I. Mikov

Established in the 60-ies, the Zlatna Panega quarry is a cement raw materials quarry supplying 95% of the needs of the Zlatna Panega Cement Plant with limestone, marl and other silica-aluminates. The two major types of raw materials are formed by accordingly dipping strata of Upper Jurassic limestones and lower Cretaceous marls. Between them there is a ?transition-zone? or ?contact-zone? of a high-silica content layer, about 5-m thick, defined as ?flint? by investigations including spot sampling throughout the quarry. For many years this ?contact-zone? layer was neglected due its negligible thickness. Further, with the increasing demand on the quality of the raw materials feed to the Plant and the focus on variability of the chemical and mineralogical components, it was decided not to mine any of the parts of the quarry contaminated by this material, for about three years. The latter had an impact on the availability of operating benches that could result in a substantial decrease in the total recoverable re-serves of Zlatna Panega, particularly with respect to marls. There were considerations for resorting to a partial, selective excavation of the quarry pit with a reduced lifetime for the lime-stones and re-opening of an other (currently in-active) marl quarry at a distance of 6 Km from the Plant. The Quarry Team of the Zlatna Panega quarry was assigned to study the problem. The ?contact? layer was duly confirmed with systematic geological (including mineralogy) studies, statistical analysis of available data, surface sampling and shallow exploration drills, resulted into distinguishing a third type of reserves and their credible subsurface delineation by means of geological 3-D modeling and quarry design. A new quarry design was finally elaborated with a view of providing flexibility in mining, utilization of the total volume of all available reserves and maximizing the mine life of Zlatna Panega quarry. An industrial test took place in December 2005, by using the contaminated parts of the quarry (co-mining of the ?contact-zone? materials) at a contribution of 15-20% in the raw materials mix, as dictated by their contribution in the total recoverable resources of the quarry. The purpose was to investigate the viability of this solution ? in line with improved quarry planning ? without compromising the quality of cement production and the efficiency of Plant Operations. Results were overall successful.

Jan 1, 2006

By Franziska Wolf, Rainer Ellmies, Helmut Mischo

"Mining is an important part of the economy of Namibia. In 2016, 11.1 percent of the GDP was the result of mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists of an underground mining operation.The global annual production of fluorspar is approximately 5.4 to 6.3 Mt (6 to 7 million st) (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu has produced on average about 45 kt/a (50,000 stpy) in recent years (U.S. Geological Survey National Minerals Information Center, 2015).The Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an openpit mine with four individual pits (A-D) since 1980. In 2014, the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently, Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village.The intent is to develop a concept for the further underground development of the mine. There are still about 6.3 Mt (7 million st) of measured resources left in the deposit, with an average grade of 27.5 percent CaF2. This study focuses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged.For solving the task to design the mine, a site visit for data collecting was conducted. Resource estimations were calculated based on existing drill data, and consequently, block models were created. The development of the mine design included the selection of the most suitable mining method, mining technology and mine organization. Moreover, some economic considerations are pointed out, followed by a profitability assessment."

Jan 2, 2018

By A. Juganda, F. WILSON, H. PINHEIRO, N. SANDOVAL, J. F. Brune, G. E. Bogin Jr.

To evaluate methane explosion hazards in longwall coal mines, a CFD model was developed along with a 1/40th-scale, optically accessible model of an underground longwall coal mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met for accurately representing the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure, and gas concentrations. This research will help develop strategies for methane monitoring that prevent methane ignitions and explosions in longwall coal operations.

Aug 15, 2022

By J. N. Hartley

Uranium mill tailings, waste products of uranium extraction, contain hazardous constituents that if released into the atmosphere and groundwater could threaten our health and environment. To provide for safe disposal and control of these tailings, Congress enacted the Uranium Mill Tailings Radiation Control Act of 1978 (Public Law 95-604). Subsequently, the Environmental Protection Agency (EPA) established standards for tailings disposal that limit radon emission into the air to 20 pCi m-2s-1 on an annual average basis (EPA 1983). The design life of the impoundment is to be 1000 years where practicable, but 200 years at least. To facilitate the design of containment systems that will meet the EPA standards, the Nuclear Regulatory Commission (NRC) and the Department of Energy (DOE) are sponsoring research at the Pacific Northwest Laboratory (PNL)* to develop the necessary technology. Earthen and asphalt materials have been evaluated for use as radon barriers (Hartley 1983) and as liners to minimize leaching (Buelt 1983). Herbicide and rock barriers against biological intrusion have been evaluated (Cline 1982). Surface stabilization techniques have been investigated to maintain the long-term effectiveness of a containment system that must be protected from wind and water erosion, chemical and physical degradation, and biological disturbance.

Jan 1, 1984

By Rongdong Deng

A tower-like magnetic system comprising eight permanent magnets was installed at the center of a flotation column to separate chalcopyrite and pyrrhotite minerals. A cyclonic flotation was installed within the underpart of the column to separate the pyrrhotite from the gangues. A three-product magnetic flotation column was fabricated to create a magnetic field and a cyclonic zone. The products were Cu concentrates, pyrrhotite concentrates and tailings. The theoretical magnetic field strengths and the magnetic forces were calculated. The results of the flotation experiments showed that the Cu grade increased from 14.20% without the magnetic field to 26.40% in the presence of the magnetic field and that the S grade in the pyrrhotite concentrates increased in the presence of cyclonic flotation. The separation efficiency of this magnetic flotation column was evident. Therefore, this three-product magnetic flotation column may have a potential application, due to its high separation efficiency.

By J. Philip Neal

Feldspar is no example of special mineralization in isolated spots: it can usually be found within a mile or so of almost anywhere. Along with silica sand, it is a major part of our world's total mineral composition. This fact imparts to it an economic status different from a sulfide ore, or potash, or phosphate. While every feldspathic "stringer" does not possess economic potential, the generous distribution does yield a high statistical frequency of good feldspar ore bodies: the adjective "good" being subject to some flexibility of interpretation. The strong chemical bonds of this alkali aluminum silicate give it certain use advantages, but under present technology its individual elements cannot practically be separated to create aluminum, potassium, sodium, silicon - or their oxides. Its present uses rely upon chemical inertness - as in fillers; and on its physical melting characteristics and their effect in glass, enamel, or ceramics.

Jan 1, 1973

By J. G. Groppo

A series of performance studies have been conducted using counter-current column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia and utilized a 0.15m (6 in.) I.D. column that was 5.79m (19 ft.) high. The refuse streams tested included both thickener feed and classifying cyclone overflow with a typical size distribution of 100 mesh X O. The percent solids of the column flotation feed varied from 1.5 to 15% while the ash content ranged from 30-60%. The concentrates produced contained 2-10% ash with BTU recoveries of nearly 90% using 0.12-1.25 kg/ton (0.25-2.5 lbs/ton) fuel oil and 0.12 kg/ton (0.25 lb/ton) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from 7 different seams are discussed as well as scale-up relationships utilized to design a full scale installation presently in operation.

Jan 1, 1990

By Andrew McGrath, Geraldine Lyons, Sarah Barcelona

In the dynamic and challenging modern industry landscape, understanding and unleashing the true role and contribution of technical teams is crucial to business success. The cyclical nature of industries has led to shifts in the technical professional’s place within the organization and the technical skills that are desired most. This paper reframes the pivotal role that technical professionals play within complex operating assets to maximize value and realize full potential. This investigation focuses on the Rio Tinto Kennecott Technical group’s cultural journey, which is underpinned by an investment in its people. The conflict between legacy industry beliefs and the necessity for cultural change emerges. This is illustrated by a deep dive into the evolving case study of Kennecott’s Bingham Canyon Open Pit Mine Technical team. Here, a multi-faceted approach to cultural change is helping to unlock the team’s contribution to the life extension of an aging asset. Guided by a vision and strategic roadmap, this approach is part way through a 5-year implementation period and is yielding encouraging business outcomes.

Feb 1, 2024

By A. L. Ling, A. K. Janzen

"Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software and water quality calculations provided by PHREEQC, and is well-suited to modeling parameters of interest in the mining industry, especially metals and sulfate. Physical processes such as membrane separation and greensand filtration are modeled by defining mass rejections for each parameter and flow routing based on vendor projections and bench- or pilot-scale equipment testing. GoldPHREEQC models chemical precipitation processes such as HDS metals removal and gypsum precipitation by (1) performing surface-aging and solubility calculations in PHREEQC and (2) using the GoldSim framework to direct supernatant and precipitate to subsequent process steps. Users can apply this modeling framework to predict effluent water quality, chemical requirements, sludge production, and required equipment capacity to support design, troubleshooting, and cost estimating. INTRODUCTION Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software (1) and water quality calculations provided by PHREEQC (2), and is well-suited to modeling treatment of parameters of interest in the mining industry, especially metals and sulfate. GoldPHREEQC can also be applied to other water treatment scenarios using inorganic reactions and processes. The GoldPHREEQC model framework moves water and mass between specified model nodes and calculates specified reaction and water quality outcomes. It can be organized to provide flow, load, and concentration information for each location, including effluent and byproduct streams, and outputs can be adapted to include power and chemical costs."

Jan 1, 2018

By Layton C. Binon

Exploration budgets are commonly determined by "rules of thumb" such as a percentage of earnings or other fiscal measure. An appropriate exploration budget is the amount needed to achieve the goals of the company. It can be determined by discounting the income expected from achieved goals. Budgets for individual projects are determined in a similar manner except that risk of failure is included in the computation.

Jan 1, 1981

By Prakash Venkatesan, Mehmet Ali Recai Ӧnal, Shaik Saida, Veerendra Singh, Chenna Rao Borra, Manish Kumar Kar

A laboratory-scale investigation of the effect of milling operation and catalyst addition ( K2CO3) on the partial reduction of low-grade pyrolusite ore pellets was carried out using coke as a reductant. Thermogravimetric analysis was used to understand the correlation between milling and catalyst addition parameters with the reduction temperatures. DTG analysis of pyrolusite pellet reduction showed three distinctive peaks associated with a three-step reduction mechanism (i.e., MnO2→ Mn2O3→Mn3O4→MnO). The results showed that the grinding and addition of the catalyst have a significant effect on lowering the MnO2 reduction temperature independently. But maximum reduction temperature drop is obtained when combining grinding and catalyst addition in this work. By 3 h milling and 10 wt% catalyst addition, the reduction temperatures were reduced by more than 200 °C compared to the raw ore pellets. These results obtained from the DTG analysis were further supported by XRD analysis of the reduced samples.

Dec 20, 2022

By S. N. Gurulaxmi, Veerendra Singh

The abstract discusses the increasing consumption of manganese ores and the need to utilize low-grade ores and rejects. The study focuses on developing a low-cost process using a cupola furnace to recover manganese values from these resources. The process involves smelting ore blends to produce high MnO slag and pig iron. The study investigates various factors to improve iron reduction and separation from MnO-bearing slag. The results show that the process can produce slag with MnO > 35% and Fe(t) < 5% using low-grade Mn ores. The process also achieves Fe reduction between 50 and 70%. The cupola furnace offers advantages like low cost and ease of operation, making it suitable for processing low-grade ores and rejects to produce synthetic MnO-enriched products for various industries.

Apr 1, 2022

By Zhenzhong Bian, Ruiyang Zhang, Xiaofeng Zhong, Zhangxuan Ning, Yuanping Zhang, Jie Lu, Airan Zhang

This study addressed the separation and recovery of vanadium(IV), iron, and titanium from synthetic and real leach solutions of vanadium-bearing titanomagnetite using extractant P204 (di-(2-ethylhexyl) phosphate) and P507 (2-ethylhexyl hydrogen- 2-ethylhexyl phosphonate). Based on the speciation analysis of vanadium in sulfuric acid medium, the single-stage extraction efficiency of vanadium, iron, and titanium was 94.21%, 3.45%, and 5.32%, respectively, under the optimal extraction condition of P204-P507 concentration of 15% (v/v), P204 to P507 ratio of 3:1 (v/v), TBP (Tributyl phosphate) concentration of 5%, sulfonated kerosene concentration of 80%, initial pH of 1.8, contact time of 8 min, and phase ratio (O/A) of 2:1. By confirming the predictions of the McCabe-Thiele diagram, a five-stage countercurrent extraction was carried out and the desirable extraction efficiency for vanadium reached 98.13%. The maximum co-extraction coefficient and distribution ratio of vanadium were 2.58 and 26.23, respectively. The stripping efficiencies and concentrations of a vanadium-rich solution by three stages of countercurrent experiments with 20 vol.% sulfuric acid reached 99.14% and 0.58 g/L, respectively, while almost all of the titanium remained in the organic phase. The mechanism of synergistic extraction between hydrogen ions of P–O–H and VO2+ in acidic conditions was confirmed by ATR-FTIR spectroscopy and molecular structure derivation. Besides, the separated impurity ions ( Fe2+) after oxidation, precipitation, and roasting process form a qualified iron oxide pigment with a total iron content of 97.2%.

Apr 25, 2023