Search Documents

By C. R. Stephan

The Mine Safety and Health Administration's (MSHA) Ventilation Division continues to evaluate proposed explosion-resistant seal designs. There are currently eleven specific designs for explosion-resistant seals that are suitable for construction in underground coal mines. Seal construction in operating mines must be equivalent to those constructed in the Experimental Mine during the explosion testing program. Accidental failures of seals have occurred due to explosion pressures below 138 Kpa (20 psi). The possibility exists that the failed seals were not properly constructed. Also, conditions in the vicinity of the seals may change. Water may accumulate against the seals, heave or sag may cause detrimental effects on the seals, and sloughage of the ribs may negate hitching. If seals are not properly installed or maintained, they could fail when subjected to explosion pressures. If seals fail for any reason, the possibility exists for explosion propagation throughout large areas of the mine. There could be catastrophic consequences to an event of this nature. This report will present a limited discussion on the construction of each of these seals and will address related issues.

Jan 1, 2001

By E. Cho

Illinois No. 6 coals of IBC 101 and IBC 112 were treated in solution with sodium hypochlorite to remove their sulfur contents, especially organic sulfur. The lab experiments were conducted in two steps of leaching at room temperature and hydrolysis at 90oC. The removal of organic sulfur from IBC 101 was by 37.8% while that from IBC 112 was only 13.7% under their respective optimum conditions. This large difference in organic sulfur removal is considered to be due to difference in concentration of surface total acid group, 3.14 vs. 0.88 mmol/g of coal.

Jan 1, 2007

By A. L. Anderson, J. T. Rybock

Lime, soda ash and similar precipitants have been the industry standard for treatment of acid rock drainage (ARD) because of their proven ability and low per-gallon operational cost. However, these methods carry serious environmental drawbacks and high life-cycle costs. KEECO’s Silica Micro Encapsulation (SME) technology has all the positive characteristics of conventional ARD-treatment systems but none of the drawbacks. SME achieves highly effective treatment in a single step, provides options for ARD prevention and recovery of metals, requires lower capital expenditures, generates smaller volumes of higher-density sludge, consistently passes leach tests, and eliminates long-term liabilities associated with potential metal remobilization and hazardous waste landfilling.

Jan 1, 2000

By Daniel J. Dobbels, Eric R. Drooff, James R. Wheeler

Construction of Boston’s C11A1 Section of the Central Artery (I-93)/Tunnel(I-90) Project beneath the existing MBTA Red Line Subway at South Station required excavation to depths in excess of 33.5 m (110 ft) through permeable sand and gravel subject to almost 27.4 m (90 ft) of hydrostatic groundwater pressure. As tacked drift tunnel underpinning system was designed to provide positive support to the active station prior to mainline tunnel construction. As part of this system, a permeation grouting program was developed to facilitate tunnel excavation. This paper describes the design and implementation of the grouting program, in sit testing, and the overall performance of the grouted soil mass.

Jan 1, 1999

By J. W. Craven, M. Katom, K. M. McCaffery

At Ok Tedi, ore type and SAG feed size distribution vary widely and frequently. This makes control of the SAG mills by application of the power/pressure relationship difficult. Power logic has traditionally been conservative due to power spikes associated with rapid size distribution changes. A new expert system was installed in early 2000. The system incorporates multiple state fuzzy logic to deal with frequent and radical ore type and size variations, along with monitoring of motor temperatures. A short term power spike no longer warrants immediate radical action. This has resulted in increased mill throughput and improved circuit stability.

Jan 1, 2001

By Ali Ahmadi, Andreas Rausch, Angela Binder, Stefan von der Mark, Dhananjeyan Jeyaraj, Jana Thomas, Nils Nöther, Stefan Wittek, Thomas Ulrich, Eleni Gerolymatou, Mario Kolling, Helmut Mischo, Michael D. Martin, Tugba Sen, Jens-André Paffenholz, Erik Farys, Oliver Langefeld, Wilfried Ließmann

This paper outlines the MOVIE project, which is dedicated to the development of a digital twin for an underground laboratory at the research and education mine “Forschungs- und Lehrbergwerk Reiche Zeche” in Freiberg (Germany). Data from induced rock deformations and temperature fluctuations is collected using fiber-optic sensors. The objective of the project is to establish a virtual laboratory for real-time analysis of the interactions between geology, geomechanics, geometry and ventilation. This will be achieved by integrating models from these disciplines with artificial intelligence, creating a sophisticated hybrid model. The insights gained will enhance safety and efficiency in mining through improved digital planning options, ultimately contributing to more effective resource management and operational decision-making in different mining environments.

Feb 1, 2025

By C. R. Hairfield

With ever rising energy costs, it is increasingly important for mines to operate with energy efficiency. As a large portion of a mine?s energy consumption is often attributed to the operation of mine ventilation fans, maintaining an efficient ventilation system is a critical pro-active way for mining companies to reduce power costs. A common way to measure a mine?s ventilation system efficiency is to calculate the volumetric efficiency, which is simply a calculation of the percentage of total mine air that is usefully employed for production. The purpose of this study is to document a nationwide comparison of the volumetric efficiency of U.S. underground coal mining operations. The results will aim to show just how efficient today?s coal mine ventilation systems are and what factors may be causing their various efficiencies and inefficiencies.

Jan 1, 2009

By Trevor R. Ellis

The extractive industries addition to the International Valuation Standards (IVS) is scheduled for publication in the next edition of the IVS book in January 2005. This will provide guidance for valuation of minerals and petroleum industry assets of all types for all appraisal uses. It will provide asset valuation support to the International Financial Reporting Standards for the stock markets of the world, and a global umbrella standard which can be supplemented for local needs by institutes and regulators. This paper discusses implementation of the IVS within the minerals industry and important issues that the industry should confront.

Jan 1, 2005

By B. Oraee

Tunnels as any other structures are affected by different loads and stresses. Generally, the loads on tunnels consist of both static and dynamic loads. These loads must both be considered in the tunnel design process. In this paper, the stability state of Jiroft water-transform tunnel is evaluated. Firstly, the in-situ stresses and then using Kirsch?s equations the induced stresses due to static loads in walls and crown of tunnel are calculated. Consequently, the strain caused by probable earthquake without considering the interaction between the concrete lining of tunnel and rock mass using seismic analysis is calculated based on free-field deformation. When the strain is determined, the simplified method of closed-form solution, Wang?s equations and Penzien?s equations are used to estimate the applied forces on the tunnel due to earthquake such as axial force and bending moment on a tunnel section taking into account the interaction of the tunnel concrete lining and rock mass. Results of this study show that the loads applied to the tunnel as a result of earthquake waves can be affect the stability of underground structures, especially long structures such as tunnels.

Jan 1, 2011

By Katzer R. Klimpel, J. Sewell

Dr. Roussey Roussev The use of chemical additives on grinding is of significant importance considering the high energy consumption of grinding processes. My research indicates that the dispersant approach explains the effects, in this particular case of wet grinding. Further, the dispersant approach combined with torque measurements give the possibility of clarifying the mechanisms involved when using grinding aids. I find the conclusions derived from the data obtained to be correct and useful for grinding. In general, I agree with the explanations. However, I would like to discuss several additional points that I consider to be important, and in the same time to mention some of my own results from investigations similar to those presented in the study under discussion. The "bed volume concept" and the change of slurry viscosity explain adequately the data plotted on fig. 3, in conjunction with Figs. 1 and 2. However, the significant increase of the average torque in the case of 83% solid with XFS-4272 introduces the necessity of establishing the optimum of percent solid when dispersant is used. For example, the optimum percent of solid for different materials varies. One of the reasons is the material's mass density. On the other hand, it is necessary to determine the concentration of the chemical used. Because of this, it would be interesting to know how the cited concentration was selected. The supportive discussion and verification by Dr. Roussev, with results similar to that of the paper, is appreciated. I will try to answer the additional questions he has raised. To begin with, the mill was fitted with six lifters of approximately one-quarter inch height. There has been extensive lab and plant level work to understand downstream influences of using dispersants like XFS-4272*. In sulfide ore processing, which is the area in which most industrial scale testing has been performed with this approach, neutral to positive influences have been observed. For example, positive effects (e.g., increased recovery) have been noticed in flotation operations involving ores that have a tendency to produce excessive slimes upon grinding. (1) Also, the use of a dispersant has been shown to demonstrate a positive influence on classification by improving the sharpness of separation and preventing a decrease in d50 value that usually accompanies increasing flow rates to classifiers.(2) The biggest potential downstream problem is in thickening, which at the dosages involved, has not been a problem in plant scale usage. The commercial price of dispersants like XFS-4272 is quite variable depending on source, concentration, etc, but a typical cost of XFS-4272 to achieve a 10% increase in throughput in industrial mills has been between 20 and 35- US per ton of feed ore (1981).

Jan 12, 1982

By L. M. Litz

In reply to Mr. DeVries comments on my paper, I would like to say that it is true, as pointed out by Mr. DeVries, that under some special conditions, the use of high concentrations of hydrogen peroxide might provide higher short term in-situ …

Jan 1, 1982

By F. Habashi

Siberia, a vast country rich in mineral resources and a large number of different ethnic groups. To the east of Lake Baikal is Buryatia with capital Ulan Ude. The Buryat are closely related to the Mongolians. Ulan Ude is connected to Ulaan Baatar (Ulan Bator) the capital of Mongolia by train – a 26 hours trip. Getting a visa to Russia is not a simple case. Visits to metallurgical research laboratories, Lake Baikal, and historical museums are enriching experience.

Jan 1, 2006

By James E. Lawver

During 1981 the Florida phosphate industry produced more than 43 million metric tons of phosphate rock - about one-third of the entire world production and also generated nearly an equal amount of waste clay and waste clay-sized product that requires dewatering and disposal. The material balance of solids and water for a typical Florida phosphate mining operation is shown in Figure 1. Historically, the industry has impounded clay waste (about 60% below ground and 40% above ground) in earthen dams, often as large as 800 acres and occasionally greater than 60 ft. high. The dams have served the triple purpose of: 1. Dewatering initial 3% solid waste clay for process water re-use. 2. A reservoir system to minimize water discharge from the mining area and to capture and store rainwater thus minimizing deep well pumping requirements. 3. The ultimate densification and storage of waste clay.

Jan 1, 1983

By K. Kovári, G. Anagnostou

Slurry and EPB-shield tunnelling have been successfully applied worldwide in recent years. Under extremely unfavourable geological conditions, however, face instabilities may occur. The present paper aims at a better understanding of the mechanics of face failure. For the case of slurry shield, attention will be paid to the time-dependent effects associated with the infiltration of slurry into the ground ahead of the face. Related topics, such as the stand-up time and the effect of the excavation advance rate, will be discussed. In the case of an EPB-shield, a distinction will be drawn between fluid-pressure and effective pressure in the chamber. The effective pressure can be visualized as a “grain to grain” contact pressure between the muck and the ground at the face. The water pressure in the chamber reduces the hydraulic head gradient in the ground and, consequently, the seepage forces acting in front of the face. The face is thus stabilized both by the direct support of the pressurized muck and by the reduction of the seepage forces in the ground. The paper includes normalized diagrams which allow the assessment of tunnel face stability.

Jan 1, 1997

By R. M. G. Machunter

Computer models of metallurgical circuits are extensively utilised in design, and prediction of overall plant separation performance. As always, in the final optimised flowsheet design there is a compromise between the recovery of values and grade of the circuit output. This paper mathematically examines various circuit options for the generation of a heavy mineral concentrate from a generic mineral sands wet concentrator plant. Based on data derived from testwork, any particular mineral sand has a unique release curve describing the separation performance of the heavy mineral suite. Models are constructed that combine particular stage output streams as feed to other stages in various configurations. The ramifications of each option are discussed and reasons why one particular option is selected over the others examined.

Jan 1, 2005

By Earl L. Rau

At the present time, whether an electric utility uses high-sulfur coal is largely determined by geographical location, clean air legislation, and the age of the power plant. Acid rain legislation may well be the new force to change the use of high-sulfur coal. A number of coal papers were presented at the SME Fall Meeting in St. Louis, MO, Sept. 1986. These papers discussed high-sulfur coal in relation to its economics, trends and prospects, value of cleaned coal, and coal-cleaning technology. The Clean Air Act of 1970 required the reduction of SO, emissions from most stationary electric-generating plant to 0.5 kg (1.2 lbs) SO2, per million Btu of heat input. It was possible for many plants to utilize lower-sulfur coal or a mixture of high-sulfur and low-sulfur coal to meet this emission requirement. This 1970 act greatly increased the use of low-sulfur western coal. The 1978 amendment to the Clean Air Act required all new plants to use Flue Gas Desulfurization (FGD) to meet a requirement of 70% reduction of potential SO2 emissions to 0.3 kg (0.6 lb) SO2 per million Btu of heat input. With the requirement to use FGD, there was little or no demand for low-sulfur western coal in new eastern power plants. If' new acid rain legislation is enacted, it likely will require sizeable reductions in SO2, emissions by existing coal users. There might then be a shift to greater use of low-sulfur coals. The low-sulfur coals could come from either western or eastern mines or from cleaned eastern coals. Economics will dictate the approach older power plants will take to meet new regulationsuse FGD or low-sulfur coal. Coal use for electric power generation has changed from 1970 to 1985. Table 1, (Land, preprint 86-333) shows the change. The table shows that in 1985, US utilities used about 255 Mt (280 million st) of high-sulfur coal. Some 45 to 54 Mt (50 to 60 million st) of high-sulfur coal is being used in plants equipped with FGD and most of this use is in eastern states. This leaves 200 to 209 Mt/a (220 to 230 million st) of high-sulfur coal being used without FGD treatment. These plants are at risk if acid rain legislation is passed. Most of these plants are in the east and are more difficult to supply with low-sulfur coal. Estimates range from $20 to $30 billion capital investment and from $5 to $9 billion dollars per year operating costs to reduce SO2, emissions from those old medium-to-high-sulfur coal-burning plants. G. W. Land, (preprint 86-333), also presents tables relating to power generating costs and coal types. The author's tables are extracted from Land's tables IV and V. Table 2 here presents costs for a new plant. This includes the impact of different heat rates, fuel costs, fuel qualities, operating and maintenance costs, labor costs, and waste disposal costs. Table 3 compares estimated costs to retrofit an older plant with a limestone scrubber versus switching the same plant to low-sulfur eastern or western coal. Costs of switching include upgrading the electrostatic precipitator and - with western coal - costs of derating. Bhagwat, (preprint 86-325), details the trends in high-sulfur coal markets from 1974 to 1984. He also gives some prospects for high-sulfur coal markets, 1984 to 1994. The prospect depends mostly on whether acid rain legislation is enacted. By 1994, if New Source Performance Standards (NSPS) continue to be applied, high-sulfur coal demand from six mid-west and eastern states is expected to increase by 27 Mt (30 million st). • L. A. Khan and J. W. Baxter, (preprint 86-373), discuss several coal cleaning technologies such as froth flotation of fines, bulk oil separation and oil agglomeration, oil agglomeration/flotation, and air-floc flotation. ? (Space limitations preclude listing references. A complete list is available from the author.)

Jan 1, 1987

By K. Vatterrodt

Thallium is not significantly removed from mining influenced water (MIW) through conventional treatment in hydroxide precipitation plants. We experimentally investigated modifications to hydroxide precipitation schemes to concurrently remove thallium. Our goal was to determine cost effective and efficient hydroxide precipitation process modifications for thallium removal. Strategies for removal targeted multiple mechanisms including sorption, co-precipitation and/or oxidation of monovalent thallium. Modifications were tested in batch and included oxidant evaluation and the role of manganese. Removal of thallium was enhanced by the addition of permanganate as well as oxygen by aeration. In addition, contact with retained solids and the initial manganese concentration played an important role in the extent of thallium removal observed. This paper reports on our findings and discusses the implications in the removal of thallium with minor modifications to the hydroxide precipitation process.

Feb 27, 2013

By Bodo Peinemann

For more than 35 years Lurgi has been providing its fluid bed roasters on a world­wide basis. The current total annual capaci­ty of the 250 Lurgi roasters approaches 26 million mt of sulphide minerals, including gold-bearing flotation pyrite concentrates. While the stationary fluid bed has been uti­lized for roasting exclusively, Lurgi has now commercially introduced its Circulating Fluid Bed (CFB) technology for gold roasting in a successful effort to maximize gold re­covery.

Jan 1, 1990

By S. K. Singh

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

By S. K. Singh, P. R. Sheorey

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999