Search Documents

By R. Xie, J. Liu, Y. Zhu, Y. Li

The surface chemistry features of spodumene and feldspar were investigated by XPS, zeta potential measurements and first principle calculation. The results indicated that the zeta potential of feldspar was more negative than that of spodumene. The most possible active sites on spodumene and feldspar were Al sites and O sites. However, the number, type and activity of these sites were different. The flotation behaviour of five new collectors (cationic collector decyloxy-propyl-amine (DPA), anionic collector α-bromododecanoic acid (α-BDDA), N-Dodecyliminodiacetic acid (DIDA), and mixed collector DPA-BDDA and DPA-DIDA) were investigated through micro flotation experiments and analysed based on the surface chemistry features of spodumene and feldspar. The results revealed that cationic collector DPA processed a high collecting capacity for both minerals. The highest recovery of spodumene and feldspar was 91.60% and 95.30% respectively. The anionic collector α-BDDA and DIDA showed poor flotation behaviour. The recovery of spodumene and feldspar when using α-BDDA as collector was less than 5% and when using DIDA as collector was less than 1%. For the mixed collector DPA-BDDA, the recovery of spodumene and feldspar was 82.27% and 32.61% respectively at pH 4.5. For mixed collector DPA-DIDA, the recovery of spodumene and feldspar was 35.69% and 9.08% respectively at pH 5.8. The results indicated that the cationic collector had high collecting capacity, but low selectivity. The collecting capacity of anionic collector for spodumene and feldspar was poor at the same concentration compared with cationic collectors. Mixed collector DPA-BDDA showed good flotation behaviour and selectivity on spodumene. The ―COO- in mixed collector might improve the selectivity. However, too much ―COO- would increase the electrostatic repulsion, which might cause low selectively and poor recovery. Keywords: Spodumene, feldspar, surface chemistry features, mixed collector, flotation

Jan 1, 2020

By Turgay Gurun

"Digital simulation can be used as an analytical tool to optimize the design of crushing plants without need for large-scale experimental programs.General mathematical description of a crushing operation permits the simulation of a crushing plant flowsheet under various operating conditions. The process model encompasses multistage open- and closed-circuit crushing of hard and soft rock. Crushing balances are analyzed in the light of crusher and screen performance and a comparison of different closed-circuit arrangements is made in terms of process and layout criteria.The simulation model allows comparison of process alternatives to be made in terms of equipment selection and capital and operating cost estimation. It thus provides the pertinent practical information to maximize plant efficiency, and to minimize expenditures in such items as equipment, structures, power consumption, and so on."

Jan 1, 2014

The two methods for calibrating the parameters K and (alpha) for use in Gy’s equation for the Fundamental Sampling Error (FSE)–, Duplicate Sampling Analysis (DSA) and Segregation Free Analysis (SFA)–, are described in detail. A case study using identical broken reef material from a Witwatersrand-type orebody was calibrated using the DSA and SFA methods and the results compared. Classically, the form of Gy’s equation for the FSE raises the nominal size of fragments given by dN to the power of 3. A later modification of Gy’s formula raises dN to the power (alpha), the latter term being calibrated with the coefficient K in the DSA and SFA methods. The preferred value of for low-grade gold ores used by sampling practitioners in the mining industry is 1.5. A review of calibration experiments for low-grade gold ores using the DSA and SFA methods has produced values of K that vary between 70 and 170 and values of in the range 0.97 to 1.30. The average value for is shown to be 1, rather than 3 as originally proposed in the classic form of Gy’s equation or the industry-preferred 1.5. It is suggested that for low-grade gold-bearing ores the equation for the FSE should raise dN to a power of 1. Such an equation for the variance of the FSE greatly simplifies the characterization of gold ores, now requiring only the calibration of K for a given mass and established fragment size. The implications of the simplified equation for the heterogeneity test are that, provided the fragments have been screened to within a narrow size range, any particular size will return a value for K that is acceptable for use in the sampling nomogram.

Jan 1, 2017

By J. A. L. Napier

It has been established that significant time-dependent stope convergence may occur over time periods of hours and days in certain hard-rock gold and platinum mines. The source of this time-dependent behaviour appears to be associated with both pre-existing discontinuities and with mining-induced fractures that form near the stope face. These induced fractures may be associated with blasting processes and may also be formed in response to high stress concentrations in the unmined regions immediately ahead of the stope face. In shallower platinum mining operations, time-dependent behaviour is, however, observed to be much less marked unless some form of specific mining-induced fracturing occurs. One particular case of considerable interest is the time-dependent behaviour that is found to be associated with the formation and deployment of crush pillars. The purpose of the paper is to present a simple limit-equilibrium computational model of this behaviour that is sensitive to both the formation sequence and the size of planned crush pillars in a mine layout. This model provides a useful means to optimize the sizing of crush pillars, and at the same time may be used to identify potentially hazardous circumstances in which pillars may not crush in a stable manner.

Jan 1, 2012

By R. D. Alorro, B. Tadesse, E. Aghaei

Cinnabar (HgS) and native mercury (Hg) are the most common naturally occurring forms of mercury found in most gold ores subsequently released into the environment during processing. Mercury and its compounds are extremely toxic and recognised as serious health and environmental hazards. This research investigates the possibility of mercury (Hg) removal from waste solutions from gold processing using iron-aluminium (Fe-Al) bimetallic particles. The synthesis of Fe-Al bimetallic particles using zero-valent aluminium and ferric chloride as precursors were performed following the optimisation of influencing factors. The presence of both metals in the prepared bimetals was confirmed by XRD analysis. The experiments for mercury removal by bimetals were designed using the central composite design and Minitab software based on two variables including contact time and adsorbent dosage. The best result of Hg(II) removal (>90%) was achieved using 4 g/L bimetals and contact time of 75 min. However, the statistical analysis of results indicated that these parameters have only a minor contribution to the removal of Hg(II) by Fe-Al bimetals. Higher bimetal dosage and contact time resulted in a higher Fe dissolution from the Al surface which can be attributed to the presence of nitrate (# $) ions in the solution. However, adding 0.1 M NaCl to the Hg solution had a positive impact on Hg removal by improving the conductivity and electron transfer within the solution. The Fe-Al bimetallic particles are promising substances for further testing of Hg removal from gold processing waste solutions with different conditions and constituents. Keywords: Mercury removal, gold processing, Fe-Al bimetals, optimisation

Jan 1, 2020

2nd CONGRESS OF THE INTERNATIONAL SOCIETY FOR ROCK MECHANICS The 2nd Congress of the International Society for Rock Mechanics will be held in Belgrade, 21-26 September, 1970. The Congress will include: working sessions, study tours, receptions, excursions introduced in the working sessions and post-congress excursions and special programme for accompanying persons. Anyone interested in rock mechanics and its applicarion may take part in the 2nd Congress. Official languages of the Congress are: English, French and German. Simultaneous translation service will be provided during the Congress. All the correspondence concerning the 2nd Congress of the International Society for Rock Mechanics should be addressed to: Sekretarijat 2. kongresa Medjunarodnog drustva za mehaniku stena Institut za vodoprivredu "Jaroslav Cerni" Bulevar vojvode Misica 43, Postanski fah 530 Beograd - Jugoslavija NINTH INTERNATIONAL SYMPOSIUM TECHNIQUES FOR DECISION MAKING IN THE MINERAL INDUSTRY The Symposium which is to be held in Montreal during the week of June 14-19, 1970, follows the Computer Symposium held in Salt Lake City this year. The purpose of the Symposium is to define the role of decision making techniques within the mineral industry and to stimulate the development of specific applications. The subject of the Symposium-mathematics, operations research and computers as applied to the mineral industry-allows a complete picture of the mineral industry in its public policy, corporate, financial and technological environment to emerge. This is another of the series of symposia on this and related subjects started in the early 1960's at the University of Arizona. Sponsorship has included a number of Universities and the Society of Mining Engineers of the American Institute of Mining. This 1970 symposium is the first to be held outside of America, and is being sponsored by the Canadian Institute of Mining, McGill University and Ecole Polytechnique. A number of delegates from South Africa have participated in these symposia and several have already arranged to attend this symposium in Montreal. Enquiries should be directed to: Secretariat, The 9th International Symposium, Department of Mining Engineering, Ecole Polytechnique, P.O. Box 50l, Snowden, Montreal 248, Quebec, Canada. 24th INTERNATIONAL GEOLOGICAL CONGRESS This Congress is to be held in Montreal, Canada, from August 21 to 30, 1972. A very detailed and extensive programme has been proposed, and includes a number of excursions. Copies of the first circular are obtainable from: The Organizing Committee, 24th International Geological Congress, 601 Booth Street, Ottawa 4, Ontario, CANADA. SYMPOSIUM ON THE RECOVERY OF PYRITE The proceedings of the Symposium on the Recovery of Pyrite, held in Johannesburg on 12th to 13th June 1969 are now available. Copies may be ordered from the Secretary, S.A.I.M.M., P.O. Box 61019, Marshalltown, Transvaal at a cost of R10.00. Papers and addresses presented at the Symposium were: Opening Address by Mr J. K. E. Douglas (President). 'The world sulphur position,' by W. C. J. van Rensburg (Member). 'The South African sulphur position,' by D. L. Taylor (Member). 'The recovery of pyrite at Government Gold Mining Areas Limited,' by R. J. Westwood (Member), G. S. Stander (Affiliate) and H. R. Carlisle (Member). 'Recovery of pyrite concentrates from colliery-waste discards-A preliminary assessment,' by W. A. Gilbert (Visitor) and E. A. Nugent (Member). 'The role of pyrite in upgrading the uranium content of Witwatersrand conglomerate ores by means of the heavy-medium separation process,' by D. J. Tutt (Associate Member). 'Pyrite recovery by jigs at Durban Roodepoort Deep Limited,' by E. J. Dominy (Affiliate), F. Diamond (Affiliate) and A. D. Graham (Affiliate). 'The storage of pyrite concentrates,' by Joan C. Campkin (Visitor) and P. J. Lloyd (Member). 'The flotation plants of the Anglo- Transvaal Group,' by L. A. Bushell (Member). 'Pyrite flotation with amines and cyanidation of the products,' by E. H. D. Carman (Member). 'Gold recovery by cyanidation from mill products obtained after pyrite flotation,' by P. G. Mrkusic (Graduate), M. Sciarone (Visitor) and H. E. Simonsen (Visitor). 'The influence of sulphydral and cationic flotation reagents on cyanidation of native gold,' by K. G. Ashurst (Visitor) and W. P. Finkelstein (Member). 'Laboratory tests on the flotation of pyrite from Witwatersrand gold ores by cationic collector,' by J. Levin (Member), and M. L. Veitch (Visitor). Closing Address, by Dr R. E. Robinson (Director, National Institute for Metallurgy).

By L. M. Tavares, H. A. Petit, P. P. Cavalcanti

Iron ore pellets experience degradation during handling due low energy impacts and stresses. These impacts lead to volume or surface breakage of the pellets, creating fine particles that accumulate along the process. Some of the particles are in contact with the air and are dragged as dust into the workplace or into the atmosphere. The aerodynamic size of the particles allows them to be potentially inhaled by the workers or to be carried to nearby communities. Dust emission becomes critical at specific locations, such as transfer chutes and stockpiles. This work models the dust generation that occurs in an iron ore pellet stockyard using a methodology that combines experiments to quantify the degradation of the pellets to mathematical modelling of the dust emission mechanisms in the stockyard. First, laboratory tests were used to characterise the amount of mass and the particle size distribution of the dust generated by degradation under controlled conditions. Second, the flow over a stockpile of an iron ore pellet company was simulated with the aid of computational fluid dynamics (CFD) simulations. Third, semiempirical equations linked the data generated by simulations and laboratory tests to estimate the dust emission in the stockyard. Finally, results were validated with measured field data, obtained with a novel online measurement tool. Results suggest that the approach is able to predict dust emission with sufficient accuracy and can be used for further implementation in the management of operations and decision making in order to reduce the environmental impact of the process. Keywords: Iron ore pellets, abrasion, dust emission, mathematical modelling

Jan 1, 2020

By N. Birtek, R. P. King

The washability characteristics of fine South African coals were measured and were found to be well characterized by an M-curve having the equation Z = aQb exp(cQ) x dQ, where Z is the ash content per 100 units of total feed and 0 is the mass yield. Parameters a, b, c, and d were determined for 23 different samples of coal from important coal seams in the main South African coalfields in the size range 0,0025 to 1 mm. The relationship between ash content and relative density was determined and correlated by means of two linear relationships. This characteristic behaviour was explained in terms of the liberation of macerals and the different association between the mineral mater and the two major macerals vitrinite and inertinite. The results obtained in this study can be used to calculate the expected performance of an ideal separation process, and can also be used as input for the simulation of real beneficiation plants. An example is worked through in detail to illustrate the method of calculation.

Jan 1, 1990

By T. Bezuidenhout, J. D. Visagie

In recent years the requirements for a barrier system between the waste body of tailings storage facilities (TSFs) and the natural ground (NG) has necessitated the use of HDPE-lined TSFs in South Africa and other countries. The addition of an HDPE liner creates an interface between, inter alia, the tailings and surrounding soils on the footprint of the TSF. It is known that low-strength materials beneath slopes can cause slope instability. One method which can theoretically mitigate this instability of a lined TSF is the addition of stability bunds along the footprint of the TSF. Altering the profile of the footprint to include slope changes which oppose the direction of the failure creates passive slices in a limit equilibrium analysis. The passive slices actively oppose the movement of active slices, resisting the mobilization of tailings, thus greater active slice forces are required to develop a failure surface running along the liner interface. Two scenarios are presented and compared. The first scenario retains the ground profile unaltered and the second scenario includes stability bunds along the ground profile. An in-depth assessment is made of the interslice forces and the interface shear stresses for each scenario. The theoretical background is discussed in greater detail to determine the mechanisms of reinforcement provided by the bunds.

Jun 2, 2022

By DeVerle P. Harris, David E. Euresty

"Potential metal supply refers to metals to be produced from as yet unknown deposits. Naturally, to measure potential supply requires, among other things, inference to the number of deposits, their tonnage, and their grade Thus, probability distributions were constructed for each 400-square mile cell in Northern Sonora, Mexico. A computer system was developed that simulated the occurrence of deposits for each cell, exploration for the deposits, and their exploitation. Evaluation was performed for each deposit by discounted cash flow analysis.An objective of this study was to explore the effect of the transportation network and required road or railroad construction upon potential supply. Consequently, the evaluation system was designed to consider the spatial location of a simulated deposit to the existing transportation network and the market destination. The construction of linkages to connect the deposit to existing transportation arteries as well as the carrying of the concentrates to the intended market were simulated. in terms of cost. The selection of the path took into account the existing terrain. This was done by digitizing topographical maps and representing the topography of the area by an orthogonal grid of elevations. The optimum route was selected by dynamic programming, meeting a prescribed gradient constraint. The potential supply of each cell was determined, allowing for the infrastructure effect."

Jan 1, 2014

By J. Mulenshi, J. Rosenkranz, P. Khavari, S. C. Chelgani

The geometallurgical concept has mainly been applied to primary ore deposits, starting from ore characterisation to the economic optimisation of the mining operation. However, as primary ore resources are becoming depleted and lower in grade, alternative sources need to be explored and a question of adaptability of the geometallurgical approach to the secondary resource repositories arises. The particle size distribution, chemical and mineralogical compositions of the Smaltjärnen historical tungsten tailings from physical separation in Yxsjöberg, Sweden were studied using drill core samples collected from different locations within the tailings repository in order to assess the amenability of the tailings to reprocessing. The tailings are dominated by the –600 to +149 μm particle size fraction. This fraction contains most of the elements of interest (W, Cu, S, Sn, Zn, Be, Bi and F) hosted by scheelite, chalcopyrite, pyrrhotite, cassiterite, danalite (both Zn and Be), bismuthinite and fluorite, respectively. The particle size distribution and mineralogical composition vary across the repository, suggesting a possible existence of geometallurgical domains, which require further assessment to evaluate metallurgical performance. Keywords: Historical tailings, tungsten, scheelite, geometallurgy, characterisation, mineralogy, reprocessing

Jan 1, 2020

By N. F. Dawson

Recovery of a chromite concentrate from UG2 flotation tailings streams, of a grade suitable for further pyrometallurgical treatment for the production of ferrochrome, has certain specific challenges not only by virtue of the decoupled nature of the primary PGM recovery process and secondary gravity based chromite recovery circuits, but also because of intrinsic variations in the nature of the ore and its mineral composition. Variability in the ore, together with upstream process dynamics, creates a challenging environment in which to achieve optimal recovery of a gravity concentrate with accurate grade control. This paper examines certain inter-relational aspects between the ore gangue and chromite mineral types, the influence of the primary PGM extraction circuit and secondary chromite extraction activity as applied specifically to UG2 ore against a background of actual plant experiences and circuit configurations applied in order achieve a suitable quality of chromite concentrate.

Jan 1, 2010

By B. Friedrich, A. Birich

Gold has been a metal of special importance for mankind for several thousand years. Its outstanding chemical resistance is an important property of this noble metal, but becomes a disadvantage when it comes to gold recovery. The established processes are based on highly aggressive and toxic reagents. Different alternative leaching reagents with a significantly lower toxicity proved to be promising alternatives in the last decades. Major research activities in this field focused on gold ores, so that leaching of secondary resources were not described sufficiently. Based on literature research and extensive experimental investigations, a reagent assessment was conducted for hydrometallurgical gold recovery from electronic waste. It was found that besides thiourea and halides, thiosulfate in particular represents an alternative of major relevance. A variety of different electronic waste (e-waste) specimens were investigated to identify suitable leaching conditions. As a result, an almost complete and selective gold recovery in less than 48 hours from different electronic waste types and components was achieved by thiosulfate leaching. Within the experiments conducted, it was found that the leaching behaviour of cyanide alternative lixiviants differ strongly from leaching of primary ores. Keywords: Gold leaching, cyanide alternative, thiosulfate, electronic waste

Jan 1, 2020

By I. H. Clark

A variety of backfills is presently being placed in different gold mines. The backfills are pumped as slurries to stopes where they are discharged into some form of retaining paddock. The effectiveness of fill as a support medium will depend on a number of factors. These can largely include (i) inherent properties of the material, e.g. particle size, shape, distribution and com- position, and (ii) conditions of placement. The terminology required for describing backfills is introduced, and the various laboratory-measured properties are presented for a variety of fills. Finally, the properties of the fills as they are placed underground are discussed.

Jan 1, 1988

By H. Brüggemann

The exploration of deposits generates geological data which are suitable for creating a preliminary tectonic and stratigraphic model. Linked with the topographical map and analysis data from exploration drillings, this information forms a numeric representation of the deposit. The following example demonstrates an expert system which connects chemical quality requirements and quarrying criteria, and develops a quarrying strategy based on the calculated model. Additional constraining factors like process technology, quarrying methods, landscape protection regulations, etc. are included. The goal is to guarantee a long-term, homogeneous material flow from the quarry at acceptable production costs - even in the case of an extraordinarily inhomogeneous deposit. In order to fulfil this requirement it is necessary to consider a large number of rules, criteria and instructions which can be structured as an expert system and programmed with LISP at a comparably low cost. The chosen strategy is not necessarily final, but can be changed any time by altering or varying the framework of conditions. The output consists of a block-working sequence which best satisfies the set requirements for appropriate points of quarry opening.

Jan 1, 1987

By K. Isaac, S. O. Bada

This research focuses on the co-firing of discard coal with refuse-derived fuel (RDF) to utilize this abundant resource in South Africa for energy generation and reduce the volume of waste disposed of at landfills. The potential of a coal with a high ash content (> 40%), which is a grade used in some power stations in South Africa, and its combustion compatibility with two different RDFs in terms of emission reductions has been established. Gaseous emissions and ash residues from the combustion and cocombustion of the coal, two different RDFs and coal/RDF blends of different proportion were analysed. One of the RDF samples contained mostly paper (PB) and the other mostly plastic (PL). Co-combustion ash from the discard coal and RDFs showed a decrease in chloride and alkali metal contents as the coal ratio in the blend increased. The slagging propensity of the co-fired blends was found to be very low, while the propensity for fouling decreased from high to medium for all the blends with < 75% RDF. Cocombustion of RDF with coal showed a decrease in SO2 emissions from 387 ppm (discard coal) to 50 ppm for the sample containing 25% coal discard plus 75% PL. A 15% PL to 85% coal blend also reduced NOx emissions from 145 ppm (100% PL) to 88 ppm. The lowest CO2 emission observed was 6000 ppm for the blend of 85% discard coal plus 15% PB. It was established that the most favourable fuel blend that can produce the lowest sulphur emissions if used for power generation is the 25% coal discard plus 75% PL sample.

Aug 2, 2022

By T. Szendrei, S. Tose

The generally accepted view in rock blasting is that the sources of energy for the fracture and movement of rock reside in the shock wave and gas action resulting from the explosion, and yet the mechanisms by which these sources interact with the rock have remained unclarified. It has also been noted that up to 50% of the work capacity of an explosive released in a blast cannot be accounted for by field measurements of energy partitioning. In this study, we describe a physical model that details the response of rock to both shock wave and gas action. An analytical model based on momentum conservation is derived to describe the dynamics of shock-driven expansion of the blasthole. Radial expansion of the hole is the key parameter that permits the derivation of the following characteristics of rock response to shock loads: hole expansion time; volume of displaced rock; energy consumed per unit volume; expansion energy efficiency; stress wave pulse length; gas pressure in enlarged hole. Soon after the completion of hole expansion, the shock wave degenerates to an elastic stress wave that runs through the burden. Blasthole expansions of between 50% and 300% of diameter are completed in under 1 ms and, depending on rock properties, consume 32% to 42% of the detonation energy or about 55% of the available mechanical (Gurney) energy. Gas pressure in the enlarged holes in five rock types is between 35 MPa and 650 MPa, and drives the mass movement of burden rock.

Oct 9, 2024

By R. S. Sarracino, M. J. Louw, S. M. Vather

Two detonation models, IDeX for ideal VOD and CPeX for non-ideal VOD, were used to predict the velocities of detonation (VOD) of five explosives: ANFO, a bulk emulsion, and three repumpable emulsions (R100 Gold, R100 Diamond, and R105). The theoretical VODs were compared with the in-hole VODs of the explosives, and the predicted and actual values were found to be within experimental error for ANFO and the bulk emulsion. The results were not consistent for the repumpable emulsions. The discrepancies can be explained as being due to variations in mining and loading practices. The results show that the detonation models can be effective tools in predicting the behaviour of explosives in different diameters and rock confinements, provided that the user is aware of the factors that can affect the optimal usage of explosives and equipment.

Jan 1, 1993

By T. Mahlangu Mahlangu, T. Fungene, K. C. Sole

"Although oxygen is widely employed as the oxidant of choice in gold leaching by cyanide, its low aqueous solubility presents some drawbacks in practical application; hydrogen peroxide has therefore been considered as a possible alternative. The aim of this investigation was to study the catalytic decomposition of hydrogen peroxide, which generates an oxidizing intermediate species, and to understand its effect on cyanide destruction. Operating conditions that facilitated the effective decomposition of hydrogen peroxide were established by varying the pH and catalyst type and concentration. The oxidizing intermediate, detected using an indirect technique, was found to be the hydroxyl radical (OH?). OH? is commonly generated in acidic solutions, but this work demonstrated that it is also produced at the alkaline pH values necessary for cyanide gold leaching. The effects of free and complexed iron and copper catalysts on the oxidation and consumption of hydrogen peroxide and cyanide were also investigated. It was shown that the cyano complexes of Fe(II) and Cu(I) are also effective as decomposition catalysts. Hydrogen peroxide concentrations above 0.01 M decreased the free cyanide concentration, which was attributed to the probable formation of the cyanate anion (CNO-). Although cyanide consumption increased due to its oxidation in the presence of OH?, excessive cyanide consumption in the presence of copper was attributed primarily to its complexation by the unstable copper(I) cyanide species. Rate constants for the decompositions of H2O2 and cyanide by ferrocyanide and copper cyanide were calculated; the latter was identified as being a better catalyst. IntroductionLeaching of gold from its ores using cyanide has been employed for well over a century (Habashi, 2016). Addition of cyanide converts the gold into a cyanide complex (Au(CN)2 -) that is soluble in water (Wang and Forssberg, 1990). The leaching reaction can be represented as Equation [1]:"

Dec 1, 2018

By P. L. Crouse

"SynopsisFluorine – in the form of hydrofluoric acid, anhydrous hydrogen fluoride, elemental gaseous fluorine, fluoropolymers, volatile inorganic fluorides, and more – has played, and still plays, a major role in the nuclear industry. In order to enrich uranium, the metal has to be in the gaseous state. While more exotic methods are known, the standard and most cost-competitive way of achieving this is by means of uranium hexafluoride (UF6). This compound sublimates at low temperatures, and the vapour is enriched using centrifugal processes. The industrial preparation of uranium hexafluoride requires both elemental fluorine gas and anhydrous hydrogen fluoride (HF). HF is prepared by the reaction of sulphuric acid with fluorspar (CaF2). Fluorine gas in turn is prepared by the electrolysis of HF. Yellowcake is first converted to uranium tetrafluoride (UF4), using HF, after which the compound is treated with fluorine to yield UF6. After enrichment, the UF6 is reduced to UO2 for use in fuel elements in pellet form.South Africa has the largest reserves of fluorspar internationally, and is the third largest producer after Mexico and China. Fluorine technology has many associated difficulties, because of the reactivity of fluorine and the toxicity of HF. The main barriers to entry into the fluorochemical industry are thus the abilities to produce both HF and F2. Both these substances are produced locally, at the industrial scale, at Pelchem SOC Ltd. Should South Africa contemplate developing its own nuclear fuel cycle as part of the awaited new-build nuclear project, it will be imperative to leverage the existing skills with respect to fluorine technology, resident at both Pelchem and Necsa, for this purpose. This paper summarizes the fluorochemical skills developed locally over the past several decades, and suggests strategies for maintaining the technology base and developing it for the next generation of scientists and engineers.IntroductionFluorine chemistry has always had a very close relationship with the nuclear industry. Although the first mention of fluorspar was recorded in the sixteenth century, and the fundamentals had been well-developed by the Second World War, it was only during the Manhattan Project (Banks et al., 1994), when almost unlimited funds were made available for the large-scale industrialization of fluorine and related compounds, that the technology took off. Expertise in both the chemistry and the engineering aspects of fluorine is essential for the design and running of several of the unit processes in the nuclear fuel cycle."

Jan 1, 2015