Search Documents

By Natesa I. Jayaraman

This report describes recent improvements the Bureau of Mines made in the design of its shearer-clearer water-spray system for dust control on lonwgall shearer faces. The improvements were based on findings from a field survey of six mines and laboratory test results. The report in-cludes information on installation and use of the improved shearer-clearer system and describes a field installation and 3-week underground test of the system. The improved shearer clearer, like its predecessor, reduces dust concentrations in the shearer operator's walkway by splitting the airflow on the upwind side of the shearer and confining the dust cloud to the face side of the shearer. The improved shearer-clearer system utilizes more practical-mounting locations for the water sprays and requires less water consumption. In the underground test, the improved system maintained the clean-air split in the walkway up to 40 ft downstream from the shearer. To further improve dust suppression, cooling-water manifolds were relocated into the loading zone. The laboratory and underground tests showed that the improved shearer-clearer system and the techniques described can significantly reduce the respirable dust exposure of shearer operators from shearer-generated dust.

Jan 1, 1985

By Alvin Schallis

Of all the uses for dolomite that depend on its magnesia content, perhaps the most important is its use in basic refractories. The quantities of dolomite (including both that used as crude and that calcined before use) sold or used for refractory purposes by producers in the United States for 1920-41, inclusive, are shown in figure 1. As can be seen from the chart, the utilization of dolomite as a basic refractory is far from new; it was, in fact, the first basic refractory used extensively in open-hearth steel furnaces. After large deposits of magnesite were opened in Austria-Hungary, the use of dolomite in the open hearth declined somewhat, only to be actively revived during the World War of 1914 to 1918, when supplies from Austria were shut off. The use of dolomite as a refractory in the steel industry again declined slightly for a brief period after the Armistice, but subsequently its use has tended steadily to increase, latest statistics indicating that more dead-burned dolomite is used per ton of open-hearth steel now than during the World War of 1914 to 1918. Despite fluctuations in consumption, dolomite has continued to be by far the most widely used basic refractory material. The following table, showing the quantities of basic refractories consumed in the manufacture of steel, the principal outlet, indicates the relative importance of dolomite. The chief reason for the widespread use of dolomite as a basic refractory is its relatively low cost. Its abundance and the proximity of the deposits to the steel industry (see fig. 2) afford every incentive to enhance the desirable physical properties of dolomite refractories and to ameliorate certain of their less desirable characteristics. The present emergency, with its huge demands upon the steel industry, has lent further impetus to the work of improving dolomite refractories.

Jan 1, 1942

By James A. Browning

Following an unsuccessful attempt earlier in the program to develop and market a drill channelling machine, we have designed and tested a new continuous channelling method which reduces operating sound levels to below 100 db. This new method relies on a small diameter oxygen-enriched burner to produce narrow channels. Sound intensities are reduced substantially compared to conventional channel widths. They are further reduced by a water spray directed immediately above the flame. Baffles placed along the top of the channel will reduce sound levels to below 90 db. Cutting rates are greater than those of existing channelling burners with costs per unit of channel area substantially reduced for those cases where oxygen costs are reasonable.

Jan 1, 1981

By BUREAU OF MINES

In 1948 the United States became a net importer of oil. Coupled with an unpre- cedented domestic production of 5,900,000 barrels daily, imports approximating 500,000 barrels made available a total supply of 6,400,000 barrels a day. Thus, by herculean effort, the oil industry was able to meet an extraordinary demand at home and, in addition, to ship abroad almost 400,00 barrels daily of petroleum and products. The country's oil position now differs greatly from that prevailing at the be- ginning of World War II. Then, actual oil production averaged about 4 million bar- rels a day, and productive capacity probably was greater than 5 million barrels a day. As the demand of the military and industrial machine grew with the rising tempo of the drive toward victory, the United States not only met its own needs but pro- duced about two-thirds of the total oil requirements of the Allied Nations, excluding Russia. As a people, we can be deeply grateful that the Nation's petroleum resources were adequate and sufficiently developed to support such a tremendous effort. Even in those critical hours when immediate needs were the paramount issues, a prudent Congress paused to contemplate the importance of an assured long-term supply of liquid fuels. From these deliberations came the Synthetic Liquid Fuels Act of 1944, which authorized research and development work on new sources of oil coal, oil shale, and agricultural and forestry products. ce World War II, a civilian demand for 6 million barrels of petroleum prod- ucts has become the order of the day every day. By drilling as many as 39,000 new wells a year, the production rate has been increased enough to meet domestic require- ments by a bare margin. Some imports were necessary, however, to fill both domestic and foreign demands, and these doubtless will increase. Is this policy of exploration within the United States and the development of oil in foreign countries adequate insurance for the fulfillment of our future national needs? This question has two aspects one purely civilian and economic in character and the other significant from the standpoint of our national defense. There are now approximately 4,000 producing oil fields in this country. At first thought, it would appear that production could decline in a considerable number of these fields without materially affecting the over-all daily output. However, 48 percent of the oil comes from only 111 major fields which contain 50 percent of the total proved domestic reserves. It is apparent, then, that the flow from large fields - having proved reserves of 100 million barrels or more each must be sustained if daily production is to be kept at the present levels. Essentially, this means that new major fields must be discovered about as rapidly or perhaps more rapidly than the older ones lose productive capacity. From 1940 through 1947, only eight major fields with estimated reserves of more than 100 million barrels each, were discovered and proved - an average of one such field a year. The total estimated reserve of these eight fields was less than 1 year's supply at the present rate of use. As drilling continues, some existing fields ultimately will prove reserves larger than those now known. Without a pronounced increase in the num- ber of major discoveries, however, the prospects for increasing our present productive level are not encouraging. Any gap that appears between domestic productive capacity and demand could be filled with supplies from proved oil resources abroad. Assuming cheap pipe-line and tanker transportation to the United States, freedom from exorbitant taxes and charges

Jan 1, 1949

By Robert J. Timko

Because of leakage through and around permanent stoppings in underground mines, more air must be forced into a mine than would otherwise be required for ventilation. As power costs increase, costs resulting from air leakage add increasingly to the operating costs of mining. The Bureau of Mines evaluated four different stopping construction techniques based on the ideas that (1) airtightness could be enhanced by brushing rather than troweling on mortar sealant and that (2) modified mortars (mortars containing glass fibers and other additives for increased strength and adhesion) would improve sealing performance. Air leakage tests comparing conventional to modified stoppings were done when the stoppings were built, after 6 months, after 1 yr, and following simple maintenance. It was found that stoppings can be built and maintained better if-- The area where a stopping is to be built is properly prepared. Stoppings are constructed using the techniques devised by the Bureau. Stoppings are periodically examined for leaks. Stoppings found to be leaking, especially at the perimeters, are resealed.

Jan 1, 1983

By K. C. Dean

Horizontal and vertical air classification systems were tested individually and in simulated tandem use for the recovery of ferrous and nonferrous metals and of other noncombustible and combustible products from shredded urban refuse. The horizontal air system with a larger tonnage throughput was used to obtain preliminary separations, and a smaller capacity vertical system was used as a cleaning device. Air elutriation, magnetic separation, and screening of shredded minus 6-inch municipal refuse recovered 92 percent of the metal in a relatively clean iron product contaminated only by adhering coatings or entrapped materials, recovered 97 percent of the combustibles in a 97-percent combustible product, and rejected 88 percent of the nonmetal noncombustibles. Cleaning of the preliminary combustible fraction produced a 98-percent paper product while rejecting other combustibles (plastics, rubber, textiles, etc.) into a 94-percent combustible product. Retreatment of the preliminary noncombustible fraction produced a relatively clean glass product.

Jan 1, 1971

By D. S. Kingery

Investigations over several years have disclosed that the principal manners of occurrence of shuttle-car injuries are in order: 1. Victims in contact with roof or crossbars. 2. Victims in contact with ribs or timber legs. 3. Victims falling from, or jerked from, shuttle cars. 4. Victims in contact with overhanging brows or protruding pine for pin timbers, or water lines. 5. Contact with persons or collisions with parked equipment. 6. Victims injured by roof falls or falling timbers caused by knocking out roof supports with shuttle cars. 7. Victims injured by runaway shuttle cars. 8. Victims injured while loading or unloading timbers or other materials from shuttle cars. These recurring types of shuttle-car accidents reflect the physical conditions of the working sections, certain safety deficiencies in shuttle-car maintenance and design, and unsafe practices by operators.

Jan 1, 1952

By Nicholas Kyriazi

The Bureau of Mines has been developing breathing and metabolic simulator technology since 1970. Breathing simulation has been widely achieved throughout the world and used in the testing of open-circuit breathing apparatus, but satisfactory metabolism simulation has not been achieved. This situation required that the testing of closed-circuit breathing apparatus, which are the only type used in mines, be done using human test subjects. The goal was a machine that could accurately simulate both the breathing and the metabolic functions of a human being for testing of closed-circuit breathing apparatus. The advantages of using such a machine instead of a human being for testing respiratory protective devices lie in its ability to quantify metabolic input, its repeatability, and the lack of a need to deal with the vagaries of human subjects. This report will describe the breathing and metabolic simulators that have been developed and used by the Bureau over the past 15 yr.

Jan 1, 1986

By W. E. Anable

The Bureau of Mines studied the purification of commercially available yttrium by melting it in a 100-kw electron-beam furnace. Button-scale melts were made to determine the ultimate purification that could be attained by melting yttrium at 1,733° to 1,770° C at low pressure (0.05 to 0.1 micron) for 1 to 120 minutes. In addition, numerous melts were made to study the effect of doping yttrium with carbon, 17 selected metallic additions, and 3 compounds. Except for nickel and zirconium, the metallic impurities in yttrium were lowered significantly on extended treatment; silicon was lowered only slightly. The nonmetallic impurities} oxygen, nitrogen, and carbon, were not lowered except on short exposures. In isolated instances, the oxygen content was lowered from 5,860 ppm to about 5,000 ppm. In most instances the carbon con-tent was lowered from 545 to about 220 ppm in 20 minutes and then increased again. It was concluded that yttrium cannot be purified by direct heating or by the doping technique employed.

Jan 1, 1965

By R. P. Vinson

The Bureau of Mines evaluated two real-time light-scattering dust monitors by measuring their response to Pittsburgh Seam coal dust and Arizona road dust (ARD). Both monitors, the model PDS-l, a personal dust sensor, and the model PCD-l, a digital dust indicator, are made in Japan by Sibata Scientific Ltd. Tests were conducted inside a laboratory aerosol chamber designed to maintain a uniform spatial distribution of the test dust. PDS-l and PCD-l measurements of concentrations for each test dust were averaged over 4-h test periods and compared with simultaneous gravimetric measurements. Both dust monitors responded linearly with mass concentration with both coal dust and ARD. However, the linear response of the PDS-l differed from that of the PCD-l for both dusts.

Jan 1, 1987

By Charles L. Ross

A successful placer mine is being operated by the E. T. Fisher Co. on Rock Creek in the South Pass mining district at Atlantic City, Wyo. About 2,800 cubic yards of gravel is dug daily by a gasoline-driven dragline shovel with a 1 1/4-yard bucket and washed in a movable plant with a gold-dredge trommel and standard-dredge sluice boxes; the total cost is about 12 cents per cubic yard. The gold-bearing gravel occupies a narrow valley between two low ranges, of hills. The ground is covered by brush and willows, which are cleared of in the fall by burning after the leaves have dried. The elevation at the mine is 7,600 feet above sea level.

Jan 1, 1935

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 6 Listing The following is a listing of the Mine Evacuation Simulation Program

Jan 1, 1976

By L. Mallett

The changing demographics of the mining industry make successful passing of knowledge and skills to the next generation critical. Training methods and technologies are being developed to meet this need. Twenty years ago classroom training was largely a one-way transfer of knowledge through instructor lectures. In contrast, instructors today can use virtual reality technologies to guide trainees as they fully participate in learning experiences. Trainees can interact with the virtual work environment, co-workers, and equipment without being exposed to workplace hazards. The speed of advancement in mine safety, health, and production training shows no sign of slowing in the next 20 years. Researchers at the National Institute for Occupational Safety and Health have studied and participated in the evolution of miner training. A look at training materials they have created in the past and those they are currently developing reveals changes in methods and technologies over time and also key characteristics which have remained constant. Possibilities for the future can he discussed in the framework of an implementation of virtual reality in new miner training sessions. The example computer-based training package teaches new miners to read mine maps and provides opportunity to practice navigation skills in a virtual mine. With this 'serious game', trainees experience the look and feel of moving through an underground coal mine while in the safety of their classroom. During field-testing in 2007, trainees and instructors responded very favourably to this new way of learning. The software was usable by mine trainers with even limited computer expertise and could be installed on the affordable computers they were using for their more traditional slide presentations. The Underground Coal Mine Map Reading Training's foundation on past successful development strategies and its acceptance by today's instructors and trainees provide valuable lessons for developing training materials, strategies, and technologies for mining's future.

Jan 1, 2009

By David M. Hyman

The Bureau of Mines has developed two experimental designs for deter- mining the volumes and relative proportions of the various gas species, particularly methane (CH4), occluded in rock salt. To date, the rock salt samples analyzed have been relatively small (400- to 1,000-gram) grab samples from Louisiana Gulf Coast domal salt mines. The results obtained are comparable to results in Polish domal salt mines, in terms of occluded gas volumes per mass of rock salt. The notable difference between the Louisiana and Polish occluded gas mixtures is in the relative proportions of the individual gas species. The two methods used by the Bureau are ballmill crushing and dissolution. Of the two, the dissolution method appears to be more versatile because it can be performed in situ. The relevance and applicability of data on the occluded gas contents of rock salt are dependent on sample size, sample collection method, geologic context of the sample, and the correlation with gas emissions that occur as a result of mining-induced fractures and pressure differentials.

Jan 1, 1982

By F. J. Palumbo

Effective recycling or disposal of flue dusts is a continuing problem for copper, brass, and bronze smelters. Over 300,000 short tons (st) of dust is generated annually by U.S. secondary copper, brass, and bronze smelters. The Bureau of Mines has developed an alkaline leach method for recovering metal values from copper converter flue dust containing zinc, tin, lead, and copper. The dust was leached with a hot solution of ammonium chloride and ammonium hydroxide to solubilize ZnO. All of the tin (as Sn02) and the metallic copper, lead, and zinc, as well as possible insoluble compounds of each, report to the residue. Dissolved copper and lead salts are removed from the leachate by cementation with granular zinc. Zinc oxide is precipitated by diluting the leachate with water. The tin-rich (9.8 pct) residue has a ready market. The cement product is recyclable to the smelting operation. The ZnO is at least 97 pct pure and has potential marketability.

Jan 1, 1985

By E. R. Rodriguez

Improved practice resulting from recent changes in the method of supplying compressed air and in pneumatic drilling equipment used in secondary drilling and in development work at the Morenci mine of the Phelps Dodge Corp., has resulted in improved safety conditions, as well as in a reduced cost per foot of drilling. A large stationary compressor installed outside the mining area and the compressed-air pipelines in the mine were replaced by portable compressor units. A self-propelled, self-contained drilling unit was obtained for drilling large footages where short moves were involved. Large wagon-drill units were replaced by faster and lighter drill machines and conventional bits by carbide insert bits. The safe practices employed in air drilling and in the related blasting and scaling operations have contributed to an excellent safety record at this mine. The complete sets of instructions listed in the company codes of safe practice aid materially in training employees.

Jan 1, 1956

By Edward F. Divers

Tills U.S. Bureau of Mines report briefly evaluates the advantages and disadvantages of basic dust control techniques presently used by U.S. coal preparation and mineral processing plants. These include ventilation, baghouse-type collectors, wet scrubbers, electrostatic precipitators, source control, sprays, good housekeeping, and personal protection devices. Two specific problems in these types of operations are also considered: dust collector system duct clogging, and control room dust control. Information provided in this report results from dust control research projects conducted by the Bureau at various coal preparation and mineral processing plants over the past decade to reduce workers' dust exposure. These studies indicate that plant ventilation systems normally provide the most cost effective method for dust control. Baghouses and scrubbers were also effective in specific applications, and examples of each are given. In extreme dust conditions, personal protection devices, such as respirators or the dust helmet, can also be highly cost effective.

Jan 1, 1990

By J. P. Coughlin

The U.S. Bureau of Mines has developed a monitoring system that acquires and analyzes data for use in determining the conditions that may precede mountain bumps in coal mines. Based on a UNIX workstation linked to an array of geophones in a working longwall operation, the system captures complete waveforms of microseismic events and simultaneously obtains continuous samples of the voltage levels of each geophone. Event rates and locations are calculated and displayed in real time on the UNIX workstation, which is situated in an underground instrumentation room. These results also are transmitted from the workstation to a display computer near the longwall face. The system runs continuously and has the capability to acquire, analyze, display, and archive microseismic (transient) data and single point data, such as closure and pressure changes, simultaneously.

Jan 1, 1993

By H. B. Brunot, L. C. IlsLey

The chief object of the Electrical Section of the United States Bureau of Mines is the study of causes and means of preventing accidents resulting from the use of electricity in mines . A large part of this work for the last 20 years has been the inspection and testing of mining equipment under the provisions of schedules which give the minimum requirements considered essential for the safety of equipment intended for use at or near the working faces of dusty or gassy mines . During the first few years of this work , particular attention was paid to the explosionproof features of the various accessories such as motors , controllers , and other parts . The knowledge of the essentials necessary for safe designs of enclosures has since been augmented by field experience and by data obtained in testing a large number and variety of designs . With our present knowledge it would seem that a disproportionate stress was placed on making the various enclosures explosionproof , but not enough thought was given to the danger from wiring and connections outside of explosionproof enclosures . The list of equipment that has met minimum requirements for safety and has been approved as permissible by the Bureau of Mines includes storage - battery locomotives , power trucks , drills , loading machines , conveyors , cutting machines , room hoists , pumps , concrete mixers , and rock-dusting machines . The wiring on some of the machines is comparatively simple and sometimes , except for the trailing cable , may be entirely within the explosionproof enclosures . In general , there is outside wiring between enclosures , and on the larger machines the wiring may be extensive and complicated . In considering the safety of wiring for mining machinery , attention must be given the severe service and unfavorable surroundings imposed by mining conditions . Some of the matters that require consideration are : ground . The lack of care of the exterior wiring to be expected in the average mine . The lack of adequate periodic inspection of the wiring . The absence of adequate facilities for satisfactory inspection and repairs under- The severe conditions of moisture , dirt , mechanical injury , and low voltage encountered in mining service .

Apr 1, 1931

By F. W. Hoertel

Tungsten from the hydrogen reduction of WF was vapor - deposited to coat MERM (Material Evaluation Rocket Motor ) graphite and rhenium- lined graphite nozzles . These nozzles have surface configurations that preclude the conventional fabrication of high- density- tungsten liners . Operation at 550 ° C produced selectively placed uniform coatings of specified thicknesses at near theoretical density . An acceptable coating could not be deposited on a beryllia nozzle because of an undesirable side reaction between the substrate and one or more of the products of the reduction reaction .

Jan 1, 1964