Search Documents

By R. W. Freedman

The gas chromatographic method, devised by the Bureau of Mines for analyzing routine mine air samples, was compared with the infrared method used for confirmatory determination of methane in mine air. While maintaining the specificity of the infrared method for methane determination, the gas chromatographic method is more precise, much more rapidly performed, and more convenient.

Jan 1, 1968

By Foster Fraas

In the separation of a component from a mixture , two fractions are obtained , one containing a high - percentage composition of the component and the other a low - percentage composition . The high - percentage fraction is frequently called the concentrate and the low - percentage fraction the tailing . In many separation processes the recovery is not complete , and the composition of the concentrate decreases as the recovery of the component, which is concentrated , increases . It is this particular class of separations to which this paper is confined .

Oct 1, 1942

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which type of plant utilizes more than the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which credo oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining.

Jan 1, 1935

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel.oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which typo of plant utilizes more thou the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which crude oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining. Although no outstanding technical developments of a fuel-saving nature were made in 1934, some progress undoubtedly was recorded. Heat exchangers, an effective fuel-saving device, wore enlarged, and some refiners now take off several cuts before the crude reaches the pipe stills. The total capacity of pipe stills increased 2.5 percent in 1934, and many of the less efficient shell stills were torn out.

Jan 1, 1935

Improve the reliability and accuracy of subsurface images using constrained tomography with enhanced ray-tracing capabilities. Background Geophysical tomography is a technique for imaging the structure of a rock mass using seismic or radio waves, in the same way that medical CAT scans image human tissue using X-rays. Tomography has found numerous practical applications related to mining, including lithologic and structural characterization, fracture detection and fluid monitoring, void detection, and evaluation of stress state and integrity of mine structures. Problems Two fundamental problems have largely prevented geophysical tomography from enjoying the tremendous success achieved by medical tomography. The first is a consequence of practical limitations on the placement of sources and receivers of wave energy: ideal resolution can be attained only when the region being imaged is entirely surrounded by sources and receivers, so that it is crossed by rays traveling in all possible directions. When such coverage is impossible or impractical, the inversion becomes underdetermined: there id not enough information in the measured data to provide a mathematically unique solution. The second major problem in geophysical tomography is the necessity for detailed ray tracing. Commercial software, as well as previous U.S. Bureau of Mines (USBM) software, employs a ray-shooting algorithm that may be unable to model some ray paths when velocity contrasts are larger than about 100%. These ?shadow zones" result in loss of data and degradation of reconstructed images.

Jan 1, 1994

By Sean Gallagher, Christopher A. Hamrick, Arnold C. Love

Twelve subjects participated in an investigation of the biomechanical stresses of asymmetric lifting in stooped and kneeling postures. Three factors were manipulated in this study: Posture (stooped or kneeling), height of lift (35 or 70 cm), and weight of lift (15, 20, or 25 kg). Subjects were required to lift or lower a box every 10 seconds for a period of 2 minutes. Electromyography (PIG) of eight trunk muscles was collected during a lift in this period. The PIG data, normalized to maximum extension and flexion exertions in each posture, were input to a biomechanical model and used to predict compression and shear forces at the L, level of the lumbar spine. Results from the EMG-driven biomechanical model indicated that compression was greater when lifting to a higher shelf (p < 0.001), and indicated a significant interaction between posture and the weight of the lifting box (p < 0.01). Peak lateral shear was not significantly affected by any main effects or interactions (p < 0.05). Anterior shear was increased with increasing height of lift (p < 0.001), and also by the posture x weight interaction (p c 0.01). A multivariate analysis of variance (MANOVA) indicated a complex relationship for recruitment of the eight trunk muscles, with the triple interaction being significant (p < 0.001). The results of this investigation will be used to evaluate safe loads for lifting in these restricted postures.

By Oliver Bowles

From the most remote periods of civilization stone has been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns), or single markers, to great obelisks and pyramids or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1650 at an estimated cost of $50,000,000 or more and is today an object of unusual interest for travelers. Other magnificent memorials both ancient and modern are to be found in many lands. No sharp line can be drawn between buildings and monuments, because the larger types of memorials such as the Bok Singing Tower, Lincoln and Jefferson Memorials, and mausoleums of various types have features in common with buildings. However, great care must be exercised in selecting a site for a quarry that will produce acceptable monumental stone because appearance as well as quality is of prime importance. The deposit must be of uniform texture and attractive color and must be notably free of knots, hairlines, impurities, incipient seams, or other defects. Many memorials are of polished stone, and spots or streaks that might be virtually Invisible on a natural rock face will appear distinctly on a polished surface. Hence, stone to be polished must be selected with unusual care. However, less flawless stone may be used for hammered surfaces.

Jan 1, 1955

By D. G. Kesterke

The electrolytic reduction of uranium dioxide to molten uranium in fluoride baths at approximately 1,200° C was demonstrated. Electrolyte constituents were BaF2, UF4, and either MgF2 or LiF. Preliminary laboratory-scale experiments were made in which the uranium oxide was added continuously for 3 to 5 hours to the cell during electrolysis. Over 1,000 grams of metal of 99-8 percent purity was made in some tests, Major impurities were aluminum, barium, iron, silicon, carbon, and oxygen. The effects of cell design, geometry, and bath composition were investigated. Electrode arrangement was the most important factor in cell performance.

Jan 1, 1963

By Arnold B. Hubbard

This report describes a method of concentrating the insoluble organic material (kerogen) in a rich Colorado oil shale without any apparent alteration of its original chemical form. The method involved treating finely pulverized shale with dilute acetic acid at room temperature to remove the carbonates, which act as a cementing agent for the shale, and cause the shale particles to partly disintegrate into the organic and inorganic components. The acid-treated shale then was centrifuged in different liquid mediums ranging from 1.4 to 1.15 gravity to effect a mechanical separation. From a Colorado oil shale containing 48.0 percent ash, kerogen concentrates containing 43.3 to 8.7 percent ash were obtained. The carbon:hydrogen ratios of the kerogen in the original shale and the different concentrates were essentially the same. The oil:kerogen ratios calculated from Fischer assays of the above samples were essentially the same, regardless of the organic or inorganic contents. This was also true of the assay water:kerogen ratios of the same samples. These data indicate that no significant change occurred in the kerogen during the concentration process.

Jan 1, 1952

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By A. W. Ambrose

A few years ago, (March 3, 1915) Congress passed a law providing for the establishments of ten mining experiment stations under the supervision of the Bureau of Mines. In 1917 the Secretary of the Interior decided that one of these stations should be devoted to Petroleum, and in the early part of 1918, approved the establishment of the Petroleum Experiment Station at Bartlesville, Oklahoma, upon the condition that the city furnish the site for the buildings and guarantee $50,000. for the erection of the buildings. A building site of 5 acres and the necessary building fund was furnished by the Bartlesville Chamber of Commerce.The buildings consist of an administration and laboratory building, both of brick construction. The former is a two-story structure of eight rooms. A large room occupying over half of the main floor is devoted to the library, reception room, and clerical force. The remaining rooms comprise a drafting room and six offices occupied by the staff assigned to this station. The laboratory is a one-story brick building and contains a well-equipped chemical and physical laboratory, also a machine shop and mechanical laboratory. In addition to the main buildings there now are on the property an experimental refinery, a blue-print house, and a store house. These latter buildings are all of sheet-iron construction.

Oct 1, 1920

By Leslie H. Sharp, Martin J. Gavin

Those of the oil-shale operators in this country who are sincerely attempting to make a real industry out of oil-shale developments, are anxious to obtain fundamental data on the retorting of oil-shale; particularly as regards the effect of certain variable factors in the process of retorting on the quantity and quality of products yielded from oil shales when they are subjected to destructive distillation. From careful examination of a con siderable number of suggested processes for treating oil shales and the con flicting ideas on which they are designed, it seems probable that accurate information of a fundamental nature is highly essential to the successful establishment of an oil-shale industry in this country. . Accordingly, the United States Bureau of Mines, in cooperation with the State of Colorado, is undertaking to furnish some definite and impartial information of this type through investigations now under way at the University of Colorado, Boulder, Colo. A retort for the distillation of oil from oil shale has been designed and installed, together with the necessary auxiliary equipment for controlling and determining variable factors of distillation, and for recovering and de termining the quantity and quality of the products yielded from the shales. The retort is of such a nature that conditions of retorting can be accurately . and completely controlled, and varied at will. It is not designed as a com mercial retort, but only for research purposes. A testing laboratory with equipment necessary for the examination of the shales, physically and chemic ally, and the products yielded by them, has also been fitted up . The material used in the investigations is oil shale obtained from the DeBeque, Colorado, shale field. It yields on distillation in the Bureau of Mines testing apparatus, about 42 gallons of oil to the ton, and is there fore a fairly representative sample of the shales that probably will be first worked in Colorado. The shale used will be as uniform as possible in character and oil yield and will all be obtained from the same seam at the same point, in order to avoid the introduction of unnecessary variable factors in the tests and to render results strictly comparable •

Jul 1, 1920

By J. B. Gayle

This investigation was conducted by the Federal Bureau of Mines to compare the selectivities of diverse flotation reagents and also of flotation and float-sink methods of separation. Flotation tests, using sodium chloride, an alcohol-type frothing agent, and a kerosine-pine oil mixture as reagents, were made on seven coking-coal samples representing four different beds. The results indicated equivalent selectivities relative to sulfur rejection when entrapment effects were minimized by recleaning the various products. Selectivities relative to ash rejection were also equivalent for some coals; for others, the selectivities of the reagents tended to increase in the order sodium chloride, alcohol-type frother, and kerosine-pine oil. Float-sink tests on these same coals generally gave results indicating better selectivities than those obtained in flotation tests at comparable levels of recovery.

Jan 1, 1960

By Byron M. Bird

"The prevailing practice of washing unsized coal, 1/2-inch and finer, to 1/8-inch and finer, on a table is subject to certain limitations which are commonly overlooked. In some instances good results are obtained by this method, but often the opposite is true and the efficiency of the washing operation is low. Although the separation taking place on a concentrating table is not fully understood, the actual distribution of particles of various sizes and specific gravities was determined a number of years ago by ore-dressing investigators. Hence this paper consists of an analysis of an old problem by new methods. The experimental data on which the discussion is based were obtained in the course of coal-washing investigations conducted by the U. S. Bureau of Mines at the Northwest Experiment Station in cooperation with the University of Washington and with certain coal operator: of that State.Experimental WorkThe general method of study has been to take a large number of zonal products from the table, and separate them according to specific gravity and size into their component parts. The table used is one of the standard commercial sizes with a diagonal deck. The coal to be washed is split into representative portions, which are stored in separate bins. One portion is used for ""timing as"" the table; the products are collected continuously in the same turned to the feed bin, and thus a closed circuit is completed. When the despite conditions on the table are obtained, coal is fed from one of the re. After the table is operating smoothly the entire product is minute; such a sample is sufficiently large to represent accurately the work of the table and at the same time to minimize the effect of beginning at the end next to the head motion, separate samples are made for each foot along the edge of the deck."

Jun 1, 1926

By Martin H. Stanezyk

The Bureau of Mines investigated leaching of selected copper sulfide minerals and a composite of impure flotation concentrates at elevated temperatures and pressures with ammoniacal solutions. Copper 1 (tractions of 96 percent were obtained by leaching chalcopyrite at 75° C under oxidizing conditions for 60 minutes. An extraction of 99 percent of the copper contained in the composite concentrate was obtained by leaching the product for 90 minutes at 75° C. In tests of bornite, chalcocite, and covellite, 90 to 97 percent of the copper was extracted at 20° C provided an 8-hour reaction period was used. At 75° C essentially complete dissolution of the copper from these three minerals was accomplished in 60 minutes. Additions of ammonium sulfate to the leach solutions were required to obtain high-percentage extractions of the copper from bornite, chalcocite, and covellite. Although ammonium sulfate was not required when digesting chalcopyrite, copper extraction was enhanced and less free ammonia was required when ammonium sulfate was added to the leach pulps. The chemistry of leaching copper minerals was studied. It was C, termined that chalcocite altered to covellite as one step in the dissolution When leaching iron-bearing copper sulfides, hydrated iron oxide formed on the mineral surfaces, indicating that a diffusion process prevailed. No evidence of covellite was detected.

Jan 1, 1966

This report presents a Bureau of Mines study comparing the construction costs, leakage measurements, and predicted performance of different types of large stoppings built and tested in a room-and-pillar oil-shale mine. The six full-sized structures (30 ft high by 55 ft wide) included both permanent and temporary stoppings and were fabricated using materials ranging from structural steel to coated brattice cloth. Leakage across each stopping was measured at differential pressures ranging up to 1.0 in w.g., using both the brattice window method and sulfur hexa-fluoride (SF6) tracer gas. Blast air pressures resulting from a full-scale face blast of approximately 1,800 lb of ammonium nitrate-fuel oil (ANFO) explosives were measured across two of the stoppings and the pre-and post-leakage rates were compared for all the stoppings. Overall performance of the stoppings for production applications was evaluated using an operational model of a two-panel oil-shale mine. Different combinations of temporary and permanent stoppings were evaluated based upon ventilation performance and construction and operating costs.

Jan 1, 1988

By Raymond B. Ladoo

Toward the end of 1920 , the average grades of ground feldspar offered to the pottery industry were so poor and so generally unsatisfactory that many of the largest consumers decided to take active steps for their own protection . A few of the potters made arrangements to grind their own feldspar , while others asked the Bureau of Mines to make a detailed study of the problem and to suggest methods of improvement . Accordingly such a study was undertaken, the partial results of which are outlined in this preliminary report . The outstanding features of the present feldspar industry which are of interest in this connection are stated below. (1 ) Many grinding companies do not own or control all or even a major part of their sources of crude material , but buy in job lots from many sources . (2 ) There is great need of more adequate engineering and chemical control over mines and mills . ( 3) ~ Out of date , inefficient methods and equipment for mining and grinding are in common use . (4) Little or no cooperation exists between feldspar producers , but on the contrary many feldspar companies are exceedingly secretive . This tends towards (a) preservation of obsolete methods ; ( b ) want of knowledge of the essential features of production , market requirements , and the relation between total milling and consuming capacities of the country; ( c ) inefficient and often mistaken trade practices ; ( d) unprofitable and even ruinous competition in dull periods . (5) The small size of many feldspar deposits precludes maintenance of an efficient organization at each individual mine . ( 6 ) Many of the best deposits of feldspar situated close to railroads are becoming depleted , which results in gradual lowering of grades , and increase in cost for better grades . (7) There is a lack of exact mowledge of the ceramic properties and behaviour of feldspar by some consumers , which results in ( a) purchase of feldspar on the basis of price alone , thus encouraging low production costs at the expense of quality , and ( b) inefficient and expensive cross- hauling of both crude and ground feldspar .

Jan 1, 1922

By W. Dan Walker

In an effort to keep mine hoist accidents to a minimum and to impart to managers and workers the essential elements that enter into safe installation and maintenance of hoisting equipment, the Bureau of Mines presents this Information Circular as a guide. Hoisting of men and materials is an essential operation in many mines and has become so commonplace that some persons are likely to ignore day-to-day inspections or become lax in the operating phases. With proper maintenance and operation, hoists can be exceptionally safe. However, lack of strict attention can invite tragedy or costly shutdowns.

Jan 1, 1961

By Elizabeth G. Baglin

Research was conducted by the Bureau of Mines to determine the feasibility of using electrokinetic densification to dewater Bayer process red mud, magnetic black mud prepared by pressure digestion of red mud in the presence of ferrous sulfate, and magnetic black mud formed by simu-lated Bayer digestion of Jamaican bauxite with added ferrous sulfate. Tests showed that the solids content of presettled muds could be increased from 25 pct to approximately 40 to 48 pct by gravity draining followed by electrodewatering for approximately 48 h. Electrodewatering may not be practical because of increased reagent and processing costs and because the muds must be thoroughly washed prior to electrodewatering to remove dissolved ions and decrease mud conductivities.

Jan 1, 1988

By D. G. Lee

Diesel particulate matter (DPM) often contains small amounts of metal as a minor component but this metal may contribute to adverse health effects. Knowledge of the mechanism for particle formation as well as the size preference of the trace metals is critical to understanding the potential for health concerns. To achieve this, the size and the composition of each particle should be optimally measured at the same time. Single particle mass spectrometer (SPMS) would be the best tool for this objective. In this paper, we therefore will introduce new findings about the mechanism and distribution of the trace metals in DPM, derived from a study where an SPMS was used to analyze freshly emitted DPM. KEY WORDS : Single particle mass spectroscopy, Diesel particulate matter, Characterization, Metal contents

Jan 1, 2006