Search Documents

By M. S. Seehra, V. S. Babu

"INTRODUCTION The accurate determination of the free silica index in coal mine dusts is an important requirement because severe health hazards are believed to be associated with the inhalation of respirable-sized silica particles.1-6 Free silica refers to the three polymorphs of silica (Si02)viz., quartz, cristobalite, and tridymite-although quartz is usually the dominant form in most mine dusts.6 The free silica index is the concentration in micrograms of free silica in air per m3 of air sampled corrected to standard conditions of 25°C and 760 mm/Hg, the present MSHA (Mine Safety and Health Administration) limit on time-averaged basis being 100 µ.g/m 3 for coal mines. A recent review7 has concluded that quartz, cristobalite, and tridymite particles impart nearly equal long-term hemolytic damage when compared on a per unit surface area basis.At present, two experimental methods-viz., transmission infrared spectroscopy (TIRS) and x-ray diffraction (XRD)-are commonly used for the determination of silica concentrations in mine dusts. In TIRS, which has been adopted by MSHA and is commonly called the P7 method, the silica absorption band near 800 cm - 1 is used for quantification. However the mineral kaolinite, which is commonly present in mine dusts, also has absorption band, albeit weaker, at 800 cm- 1• To correct for this interference, one uses the stronger 915-cm -1 band of kaolinite to determine the concentration of kaolinite, and the kaolinite contribution to the absorbance at 800 cm-1 is then determined from a calibration curve, leading to the determination of silica by subtraction. In the XRD technique, usually an internal standard such as CaF 2 is used to determine the concentration of silica from line intensity measurements. XRD has the added advantage that concentrations of quartz, cristobalite, and tridymite can be determined.8•9 In an exhaustive study on the precision of the techniques ofTIRS and XRD for monitoring worker exposure,9 the conclusion has been reached that both methods measure silica within 253 of the ""true"" value 953 of the time in a single laboratory."

Nov 1, 1995

By Robert J. Evans

Reclamation costs were estimated for 20 coal surface mining operations in the Appalachian and Midwestern Coal Supply Districts (these two districts were divided into three multi-State regions). The cost data were obtained through onsite observations, interviews with mining company personnel, and the authors' cost estimating procedures. The cost data are presented in terms of dollars per acre, dollars per ton of coal produced, and dollars per cubic yard of overburden moved during backfilling. The reclamation process is divided-into three cost categories: Premining planning, backfilling, and revegetation. The average total reclamation costs for the three regions are $2.77 per ton of coal produced and $8,168 per acre. As the result of comparisons of reclamation costs by region, by mining method, by slope, and by size of operation, the most important reclamation cost difference is between area mining methods ($1.73 per ton) and contour mining methods ($3.81 per ton). The Federal Bureau of Mines conducted this study to determine as accurately as possible the actual costs involved with the reclamation of coal surface mined land done in conjunction with active mining operations.

Jan 1, 1975

By Eugene Frey

The Romur is one of several properties in the Copper Mountain mining district, Fremont County, Wyo., that contain scheelite deposits. The district lies on the southern slope of the Bridger Mountains, 18 miles northeast of Shoshoni and 15 miles from the rail point at Bonneville on the Chicago, Burlington & Quincy Railroad (figs. 1 and 2). The tungsten deposits occur in a zone of pre-Cambrian schists and gneisses that have been cut by numerous basic dikes and granite pegmatite dikes. Scheelite occurs in lenses and pods that lie parallel to the foliation and bedding in the metamorphic rocks. The more important deposits are found in a lime-silicate rock consisting primarily of zoisite but with small quantities of quartz and carbonate. Scheelite was found in December 1941, and the area was mapped by the U. S. Geological Survey early in 1942. In November 1942 the Bureau of Mines commenced work on the Stardust-Comet group for the purpose of developing reserves for war requirements. The initial work consisted of driving an alit in the ore zone a distance of 109 feet. This zone was sampled during the progress of the work, and subsequently surface and underground exposures on adjoining properties also were sampled (figs: 5, 6, 7, and 8). One hundred twenty-four samples were obtained. Sample and assay data are shown in tables 2, 3, and 4.

Jan 1, 1950

By H. E. Powell

Magnetic susceptibilities were determined by the Bureau of Mines fur 19 cobalt- and nickel-bearing minerals and for a suite for synthetic cobalt-nickel diarsenides analogous to the rammelsbergite and safflorite series. Relations between susceptibility and composition were found to be nonlinear for both impure natural minerals and pure synthetics.

Jan 1, 1967

Introduction The NIOSH Office of Mining and Construction Safety and Health Research has redesigned its Mining Safety and Health Web topic page. The updated page incorporates a significant amount of new safety and health information, plus an improved layout to better serve stakeholder needs. It also provides back-ground information about the NIOSH Mining Research Program, including research awards, core competencies, unique labs, community and educational outreach, and a brief discussion of how the research program is structured. The new Web topic page can be found at www.cdc.gov/niosh/mining. "Search" Feature The redesigned Web topic page features improved search capabilities. The "Search Mining" feature on each page lets you search only the NIOSH Mining Safety and Health Web topic page. The user can still search the entire NIOSH Web page by using the "Search NIOSH" option. New Safety and Health Topics Developers expanded the "Safety and Health Topics" and reorganized the site to make it easier to find information. Each topic link now has a significant amount of new and updated information, as well as links to related topics of interest. Safety and health topics include dusts, diesel exhaust, hearing loss, contact with electric current, fires, explosives, ventilation, emergency management, new and older workers, and education and training. All topics can be accessed from the home page (Figure 1). Publications Although the Web topic page highlights many of the most requested publications on the safety and health topic links, you can find a complete list of downloadable publications as well. More than 600 mine safety and health publications are now downloadable from the page. Short summaries let the user quickly identify publications of interest. Products The updated Web topic page offers more than 120 NIOSH mine safety and health products, including training exercises, toolbox talks, videos, computer software, guides, and checklists, many of which are downloadable. If not, instructions are given on how to obtain copies. Some of our products include: • Software to analyze horizontal stress, design pillars for longwall mines, and select roof bolts for ground control. • Educational software including the Hearing Loss Simulator, which simulates the effects of noise and aging; and Coal Country, which teaches children about coal formation, mining techniques, and everyday uses of coal. • Utility software including the HazCom Helper software to assist individuals in writing a HazCOM plan, as required by the Mine Safety and Health Administration (MSHA), to track hazardous chemicals at their mine sites. • Guides for troubleshooting roof support systems, under-ground workstation design, and seating design. • Training exercises and videos that can be used for safety training. Data and Statistics General mining statistics are used by a wide variety of stakeholders. The NIOSH Mining Web topic page offers statistical graphs, tables, maps, fact sheets, and other publications that document the mining population, injuries, fatalities, diseases, and occupational exposures for all mining commodities. If users prefer to analyze data themselves, downloadable files of MSHA data are available. These cover employment, production, injuries, fatalities, and accident data from 1983 to the present and are available in both SPSS® and dBASE® formats.

Jan 11, 2005

By Robert S. Sanford

In April 1948, the Bureau of Mines was requested to evaluate the graphite deposit' known as the Benjamin Franklin and Just mines in Chester County, Pa. After preliminary investigation, it was recommended that the Bureau core-drill, trench, and sample the deposit and make beneficiation tests on the ore. During the first and second World Wars, flake graphite was in short supply, and a number of deposits in the United States were exploited. In 1942, the Defense Plant Corporation, through its lessee, the Benjamin Franklin Graphite Co., purchased 70.263 acres of graphite-bearing land and built a complete mining and milling plant with a capacity of 300 tons of crude ore per 24-hour day at a cost of $426,250 (Plancor No. 1254).

Jan 1, 1949

By A. T. Coumbe

During 1953-55, 31,105 miles of pipe for transporting crude petroleum and refined products was laid in the United States, a total slightly below that of the prior 3-year period, according to data compiled by the Bureau of Mines, United States Department of the Interior. The added mileage consisted of 22,571 miles of new pipe, representing about 2,163,807 tons of steel, plus 8,534 miles of secondhand pipe, equivalent to about 419,849 additional tons of steel. During the 3-year period, 13,069 miles of pipe was taken up. By January 1, 1956, the Nation had 188,540 miles of pipeline, an 11-percent gain over the 1952 total of 170,504 miles. The greater use of larger diameter pipelines indicated in recent surveys has continued, as the mileage for sizes 12 inches and over increased from 13 percent of the total mileage at the close of 1952 to 16 percent 3 years later. Crude-oil trunklines 12 inches and over in diameter gained 24 percent during 1953-55, and these larger lines represented 30 percent of the total mileage compared with 25 percent at the close of 1952. Furthermore, the mileage for crude-oil lines less than 12 inches in diameter declined 2 percent and made up only 70 percent of the 1955 total against 75 percent n the previous survey. Product Lines 8 inches and over increased 43 percent from 1952 through 1955 and composed 70 percent of the total mileage compared with 66 percent in 1952.

Jan 1, 1956

By M. R. Geer

The use of the cyclone as a dense-medium cleaning device was first described by Driessen6/ in 1945, after development of the process in the Netherlands during the German occupation of World War II. A pilot plant was built in the Netherlands soon thereafter, and the first commercial plant was built in 1948. By 1958, 18 plants were operating or under construction.7/ Thus, economic factors in Europe, where the high cost of coal places a premium on efficient cleaning, dictated rapid adoption of the cyclone. American reception of the process differed. The Bureau of Mines presented the results of its own small-scale cyclone experiments in 1946;8/ showing a sharp separation between coal and impurity; adoption by industry now is taking place. There is now much greater emphasis on the efficient cleaning of fine coal, and the first American cyclone plant has begun operating; others are planned or under construction. With the present interest in improved treatment of fine coal, the Bureau of Mines felt that additional performance data on the cyclone would be helpful to industry. Therefore, a complete, open-circuit pilot plant was built to make cleaning trials on American coals covering a wide range of washability characteristics. Five raw coals and one middling product were included in the investigation, and each was cleaned at several densities; 17 cleaning trials are reported.

Jan 1, 1961

By M. R. Geer

Samples of coal from six beds in the Roslyn-Cle Elum field of Washington were subjected to float-and-sink tests to determine their amenability to the production of high-ash boiler fuel for on-site power generation. Grindability tests and analyses of ash were made. All of the coals would require some degree of cleaning to insure a product of 25 percent ash. With two of the coals the entire size range would have to be washed. With the other four, it would suffice to clean only the coarse coal and bypass the raw fines.

Jan 1, 1965

By R. Hogg, T. F. Dumm, L. G. Austin, M. Yekeler

"Dedicated to Professor Kurt Leschonski on the occasion of his 60th birthdayAbstractThe kinetics of batch grinding quartz from a feed of 600 by 425 Jim to a product of 80% less than 10 µm have been determined using screening and laser diffractometer sizing for size analysis. The specific rates of breakage decreased by a factor of about three when the material became less than about 100 µm in size, but the primary breakage distribution function also changed to give proponionately more fine material, so that the grinding efficiency expressed as the development of surface area (B.E:T.) per unit of energy input did not decrease. Analysis of the shape of the particles in the 2S x 38 µm size range showed that particles of this size produced by roll crushing or by 8 minutes of grinding of a 42S x 600 µm feed were not different but at long grinding times the particles were rounded. This suggests that the breakage mechanism changes to give more chipping and abrasion and less disintegrative fracture. As the material approached the ultrafine size range it adhered to the mill case and there was no further size reduction. However, a technique for striking the mill case to dislodge the particles was successful in allowing further grinding to 400Jo by weight less than 2 µm.1 IntroductionIt has long been known that it is difficult to accomplish ultrafme grinding in a tumbling ball mill. It has been reported [12, 13] that there is no further size reduction after some hours of grinding cement clinker in laboratory ball mills. Austin and Bagga (1] and Shah and Austin [16] have given an analysis of the kinetics of dry grinding in a laboratory ball mill, introducing the concept of a slowing-down factor K, which is the ratio of the specific rates of breakage at some long time of grinding to the normal specific rates of breakage. They showed that this factor decreased as fine material accumulated in the mill charge. Cottaar and co-workers [8-10] showed that the movement of solid in a dry laboratory ball mill was influenced by the fineness of the solid and by the presence of air, and that evacuation of air from the mill caused particle sedimentation and low rates of breakage.The concept of the slowing-down factor has also been used in wet grinding [17, 18]. At very .high slurry concentrations it appears to be correlated with a steady decrease of mill power caused by the build up of a layer of deposit sticking to the mill case. This reduces the effective mill diameter and, eventually, the balls start to adhere in the layer and centrifuge. A decrease of mill power always indicates less lifting and tumbling of the media and, hence, less breakage. However, slowing-down of breakage rates was also observed at lower slurry concentrations where there was no change in mill power."

Jan 1, 1990

By A. W. Khair, S. J. Jung

"A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.1. INTRODUCTIONMuch research in the past has been done on energy requirements and mechanism of energy dissipation for ideal rock fragmentation in cutting process. However the mechanisms of energy dissipation or failure criteria for rocks in cutting process in order to evaluate the efficiency of energy requirements in specific rock fragmentation is not well understood. The formation of a crater in rock under the impact blow of a bit has been observed experimentally (Hartman, 1959). It is known that directly beneath the edge of the bit the rock is crushed into fine powder, toward the sides of the crater it chips out into relatively large fragments. (Sikarskie & Cheatham, 1973). Singh et al. (1967) investigated the cratering process under the two different conditions of static and dynamic loading. They found that the amount of energy consumed per unit volume of crater is unequal for the two different loading conditions. A complex network of fractures often extends downward and laterally into the rock below the bit. The surface of the specimens showed that the dynamic loading damaged larger area then the static loading."

Jan 1, 1989

By Stella Sigler

This publication contains analyses and related source data for 153 natural gas samples from 16 States. Of the total samples, 149 were collected during calendar year 1993. The remainder were collected earlier, but releases granting permission to publish were not received until 1993. None of the analyses have been previously published in annual reports. All samples were obtained and analyzed as part of U.S. Department of the Interior, U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1994

By L. A. Johnson

This Bureau of Mines report presents the analysis of three cores from the Asphalt Wash area of the P.R. Spring tar sand deposit of northeastern Utah. Two tar sand zones are indicated in the Asphalt Wash Area. Total net thickness of the tar sand ranges from 23 to 39 ft, with occurrences between 56 and 263 ft in depth. The sand has average porosity of 24.7 pct of bulk volume, average permeability before and after extraction of 87.5 and 596 md, respectively, and average oil saturation of 58.1 pct of pore volume. Oil gravity averages 10.9° API.

Jan 1, 1975

By D. A. Reynolds, A. C. Fieldner, S. H. Katz

"03-01-192403-31-2019RI 2591 - Reports of Investigations - Department of the Interior - Bureau of MinesBureau of MinesPittsburgh Experiment Station American Society of Heating and Ventilating EngineersU.S. Public Health ServicesTucson Experiment Station Introduction.""Carbon monoxide self-rescuers,"" or simply ""self-rescuers,"" are pocketsize gas respirators which protect the wearer from air contaminated with poisonous carbon monoxide gas. On March 6, 1924, the Bureau of Mines approved the ""M.S.A. self-rescuer’ manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa., after the M.S.A- self-rescuer bad passed all the tests and requirements of the Bureau's Schedule 14A4.The purpose of the self-rescuer is to help miners to escape from mines in which fires are burning or explosions have occurred, by providing protection from carbon monoxide for at least one half-hour. The self-rescuer can be used similarly by workers above ground who may through accident become surrounded or entrapped by atmospheres containing carbon monoxide.no hazards threaten the miner, who escapes serious injury by fire or violence in a large mine fire namely, ( 1) asphyxiation by poisonous carbon monoxide gas; and (2) suffocation by insufficient oxygen to support life. In order to save himself, the miner must either erect a barrica4e5 against afterdamp and wait restoration of ventilation and rescue or take a long chance at getting out of the mine through entries not permeated by afterdamp.. The self-rescuer removes the hazard of carbon monoxide poisoning for one half-hour or more, and accordingly greatly increases the miner's chance of saving his life.This paper describes the construction and details of the M.S.A. self-rescuer as approved by the Bureau of Mines, and discusses its performance under test condition"

Mar 1, 1924

By M. R. Geer

Three coals from the Wilkes on - Carbonado district of Pierce County , Washington , were subjected to washability analyses to estimate the amount and quality of washed coal obtainable . Because the coals were unusually difficult to clean , the washability examinations were supplemented by table tests , tests in dense - medium cleaning units , and flotation tests . None of the coals could be reduced to the desired 10 percent ash by tabling and the response to flotation by two of them was poor . Dense -medium treatment provided coal of the desired quality , but with the most difficult coal the recovery efficiency was lower than usual .

Jan 1, 1964

By W. W. Adams

Three hundred and twenty-eight mines and quarries, representing 36 States, took part in the twelfth yearly accident-prevention contest conducted by the United States Bureau of Mines and known as the National Safety Competition. Four underground mines and one open-cut mine (which represents the quarry and open-cut mine group), each the leader in its group, were awarded the ?Sentinels of Safety? trophy. Relative standing in the contest" was determined by the number of days lost from accidents in proportion to the total number of man-hours worked. Since 1925, when the National Safety Competition was inaugurated, an increasing interest has been taken in it by mining and quarrying companies as a means of stimulating mine and quarry safety by competition among similar plants. Each participating plant can, on a basis of its standing and record in the contest, determine to what extent its safety program is succeeding or to what extent it needs strengthening. With this information, each company that has a low standing in the contest can intensify its safety-promotion efforts the following year to obtain a? lower rate and possibly win the trophy or achieve honorable mention in the competition. Except for 1929, the National Safety Competition of 1936 represented more man-hours of employment than any other year since the yearly contests began.

Jan 1, 1937

By S. J. Page, W. E. Wallace, P. Bolsaitis, D. Eppelsheimer, M. J. Keane, J. Poston, J. Harrison

"Respirable-sized dust particles from a clay mine and mill were examined for aluminium and silicon content by scanning electron microscopy-energy dispersive X-ray analysis at incident electron energies of 5--20 keV. Most of the high silica content particles, those which had a silicon to silicon plus aluminium signal fraction, measured at 20 ke V, of0.9 or greater, showed a decrease in the silicon fraction of signal with decreasing incident electron energy, down to values of between 0.6 and 0,8 at 5 keV: this decrease was a function of particle size and composition. Simple models for silicon fractiol) of signal vs incident electron voltage suggest this behavour is due to a heterogeneous particle structure in which an aluminosilicate coating occludes the surface of a silica particle core. The coating survives incubation in a major component of pulmonary surfactant.INTRODUCTIONMINING and some other dusty workplace atmospheres are monitored for respirable dust and quartz dust for purposes of occupational health protection, respirable quartz dust being a known cause of pulmonary disease. Respirable quartz exposure data are acquired also for epidemiological research on the correlation of pulmonary disease prevalence with respirable dust composition and concentration. For these purposes quartz content often is measured on collected dust samples by X-ray diffraction or in spectroscopy. Scanning electron microscopy-energy dispersive X-ray analysis spectrometry (SEM-EDX) is also used. The first two methods measure the bulk composition of a multi-particle dust sample; SEM-EDX measures the elemental composition of single ·particles. These methods as typically applied, including SEM-EDX with a 20-30 kilo-electron volt (keV) electron beam accelerating potential, do not distinguish homogeneous distribution of impurities in a particle from possible heterogeneous surface distribution. These measurements of quartz content are not always accurate predictors of the prevalence of dust-induced disease (ROBOCK and BAUER, 1990), which implies that the biologically available quartz surface may not be equivalent to conventionally measured quartz content of respirable dust in some exposure settings. Using a minor modification of conventional scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) protocols on samples of settled and airborne dust from a clay mine and mill we have detected heterogeneity with depth for aluminium impurity in high silica content particles, indicating that some of the quartz or 'free silica' respirable particles of the dust are aluminosilicate occluded. Coatings were not removed by incubation of the dust in a surrogate pulmonary hypophase surfactant fluid."

Jan 1, 1990

By H. B. Brunot

A complete list of permissible mine equipment , tested and approved by the Bureau of Mines previous to January 1 , 1947 , was published as Information Circular 7432.27 A list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar year 1947 was published as Information Circular 7465.3/ The present list supplements Information Circular 7432 and includes all of the equipment approved during the calendar years 1947 , 1948 , and 1949. It therefore supersedes Information Circular 7465. The list also includes an appendix ( No. 2 ) giving the symbol that must be used by every cable manufacturer in marking trailing cables that have passed the test for flame resistance as stated in the amendment of October 21 , 1947 , to Schedule 2E . The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification . Thus , Information Circular 7432 showed six air compressors on the active list ; five additional compressors , Nos . 7 to 11 , inclusive , in this category were approved during 1947 , 1948 , and 1949 . Several items that were listed in Information Circular 7432 have been repeated in this circular where it was necessary to show that approvals of such equipment were extended to cover an additional voltage rating or other changes . Equipment listed in these circulars is approved by the Bureau of Mines only when found , upon inspection and test , to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal -mining industry . The use of such equipment in mines known to be gassy , as well as in those that may become so , is earnestly recommended in the interest of safety . This circular is published so that the industry may be kept informed as to the many types of machines , devices , and lamps that are available for reducing explosion and other hazards incident to coal mining . This circular and Information Circular 7432 give the complete list of permissible mine equipment that is available under the various classifications .

May 1, 1950

By Frank J. Wiebelt

The Veta Chica and Cerro Colorado chromite deposits of the McGuffy Creek area, Siskiyou County, Calif. were selected as worthy of investigation by the Bureau of Mines in accordance with the Strategic Minerals Act of 1939. These were two of many chromite deposits examined by engineers of the Bureau of Mines during their extensive wartime mineral examination and exploration campaign. Exploration by the Bureau of Mines consisted of 2,234 feet of diamond drilling, surface trenching, and sampling during the months of May and June 1942.

Jan 1, 1949

By R. G. Knickerbocker

[The Electrornetal~.1~~1c~.l T,:tt31~tn~ir of the Bureau of Miner,, 3oulder City, !.Tev. , invsst:'.~:es 1:h .-inc.z-.l ci.c;,oritr, in 51-3 regon around Boulder Dam, i~d. this papei- ?i*esmt; tvr) cl-c~;ef.o!~~ilcinl;$ of n s5siqn of atufiies on boron ninerala GB~O 3;; tlir t ~t;s?,Lo:]

Jan 1, 1940