Search Documents

By G. Walsh, L. Wolkovitch, A. Savage, V. Romero, T. Zimmerly, G. Imahara, J. Hyneman, K. Byron, D Tapster, S. Belleci, J. Metzger, M. Stanley

Testing was conducted at the Energetic Materials Research and Testing Center for the MythBusters on three separate occasions. This testing included (1) an experiment designed to create diamond from graphite using the shock and pressure of a detonation, (2) the flattening of a car using a steel plate driven by a rocket sled, and (3) the bifurcation of a car also using a rocket sled. All tests were successful; diamond was produced following the detonation of ANFO, and extracted from a graphite / cobalt matrix. A plate was accelerated to 646 mph (1040 km/hr) using a two-stage sled system loaded with 5” (12.7 cm) high velocity aircraft rockets (HVAR) into a car, which was subsequently demolished. Finally, a steel wedge was pushed to 541 mph (871 km/hr) by a one stage sled using HVAR rockets, and was able to cleanly cut a target car in half.

Jan 1, 2010

By Dadan Munawar, Benny Gunawan

Blasting at Sebesi in Central Tutupan Pit area in South Kalimantan, Indonesia is planned to be using emulsion, where used oil makes up 50% of the total emulsion fuel. The significant amount of used oil from various mining operation units had been of deep concern since it might be reused to implement environmental programs by substituting 50% of fuel with used oil in emulsion, thus decreasing fuel consumption and increasing efficiency by reducing fuel cost. Used oil must pass laboratory test to meet the Indonesian National Standards (SNI) No. 7642:2010 of used oil specification. Other considerations include the location which is adjacent to the mine office facilities with a radius of <1,750 meters (5,741 feet). Thus, appropriate methods must be performed to meet the SNI No. 7571:2010 of vibration threshold in order to implement safe blasting technique and prevent potential damage.

Jan 1, 2015

By Farshad Rashidi Nejad, Ali Asgari, Sanaz Norouzi

Blasting is known as the first step of rock breakage in mines. An indication of the importance of blasting is that more than 1 billion kg (2.2 billion lb) of explosives are used annually in Australia and 3 billion kg (6.6 billion lb) in the United States for rock breakage, more than 85% of which is used in the mining industry. The notion that blasting, as the first step of comminution, plays a significant role in crushing and grinding energy consumption is not an unfounded thinking. It can be noted that the comminution electrical energy consumption decreases in these ways: First, if the feed size to the primary crusher is decreased, less energy will be required to crush the ore to the same product size. Second, a decrease in work index (Wi) related to additional macro fracturing and micro fracturing within individual fragments.

Jan 1, 2015

By Marion Smith, Thomas M. Keevin, Dennis G. Wright, Gregory L. Hempen, Joel B. Gaspin, Thomas L. Linton, Gregg R. Gitschlag

"A Natural Resources Working Group, within the International Society of Explosives Engineers, reviewed published environmental effects data, identified data gaps, and prioritized data collection needs relative to underwater explosive use. Six groups of organisms were reviewed: 1) aquatic plants, 2) aquatic invertebrates, 3) fish, 4) amphibians, 5) reptiles, and 6) marine mammals. Studyrecommendations included: conducting basic research to determine the relationship between pressure waveform and mortality where little or no data exist (e.g., aquatic plants, fish, amphibians, reptiles, and marine mammals) and conducting narrowly defined studies where adequate data have been acquired (e.g., aquatic invertebrates). The goals of the recommended studies are to develop the relationship between pressure waveform and mortality/damage in order to construct mortality models. Development of comprehensive mortality models would be extremely useful to the blasting community for assessing environmental impacts and developing strategies for reducing impacts from explosives used underwater."

Jan 1, 1999

By Travis Watts, Chris Prater, G. T. Lineberry

Moving overburden at minimal cost is becoming increasingly important to coal mining companies throughout the U.S. The coal market is currently doing well, with an average spot coal price for Central Appalachia product (12,500 Btu, 1.2 SO2) standing at $62.00 for the week ending November 11, 2005, so it is at this time that companies stand to achieve healthy rates of return on their investments. Cast blasting is one method of blasting used effectively by some surface mining operations. This method allows most of the overburden to be removed and placed (cast) directly in the spoil pile by the use of explosive energy. With the proper design of a cast blast, a high percentage of overburden material can be directed into piles without the use of earthmoving equipment, hence increasing production and lowering the cost associated with overburden removal.

Jan 1, 2006

By P. E. Hoffman, Joshua Ph. D.

The Institute of Makers of Explosives (IME) led a post-detonation debris collection project in conjunction with a large AN railcar detonation conducted by the Department of Homeland SecurityTransportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in the IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk) Quantitative Risk Assessment (QRA) tool. The test also provided valuable data about AN detonation characteristics when it is driven to detonation. The test took place at the Utah Dugway Proving Grounds (DPG) on April 27, 2018 and the debris collection was conducted the following two weeks with an average of 20 persons per day and an approximate total of 1,400 manhours. This paper details the collection efforts, challenges, and lessons learned. It also presents some of the initial findings relating to the debris distribution.

Jan 1, 2019

By Allan King

Ammonium Nitrate (AN) is most commonly encountered as either a prilled solid or a highly concentrated aqueous solution, with or without organic ( e.g amine) nitrates. Under certain conditions of fire exposure involving prilled or solid AN, the molten state can be formed. The shock sensitivity of the molten material at temperatures greater than 220 Celsius has been found to be much higher than that of the prilled or solid form. Molten AN can be a precursor to events leading up to explosion of a bulk prill storage pile as a result of fire exposure. The explosion hazards presented by molten AN are a function of two factors; 1) its shock sensitivity and the deflagration to detonation ( DDT ) properties of the molten material, and: 2) the ability of large masses of unfueled prilled AN to be initiated and detonate. This paper presents the results of tests designed to determine the shock initiation and DDT properties of the solid ( prilled ) and molten AN.

Jan 1, 2008

By Chuck Kliche, Bill Clements

This paper relates some of the experiences, good and bad, of blasting adjacent to residences of the primary author during his 15+ years of field blasting in the Northern Great Plains region. During this highly-rewarding blasting career, the author has become aware of two major issues in residential blasting: 1) What we call “Risk/Reward Ratio.”Some questions that must be asked by the blaster prior to taking on any blasting job include: - Can we eliminate or minimize the risk? - Is the reward worth the risk? - Do I have a measure of “nervous confidence” about the shot? 2) Public Relations. Two key elements to public relations are: - Notification - Education All the education in the world to the adjacent populous of what’s happening, of blasting in general, or of what to expect from the blasting does little good without notification. Good public relations is a key to controlling the cost of liability in a litigious society.

Jan 1, 2009

By Lon D. Santis

The Code of Federal Regulations Title 30, Parts 56, 57, 75, and 77 require that detonators and explosives be separated by four inches of hardwood or equivalents when transported together in mines. This standard was developed to protect the explosives from initiation by the more sensitive detonators. The research reported here is an attempt to quantify the fire protection offered by four inches of red oak and other materials. Boxes with a volume of 6.75 cubic feet were made from four-inch thick rough green oak (RGO), two-inch thick RGO plied, two-inch thick #1 common (dried) red oak plied, and a metal/plywood composite. These and boxes meeting the Institute of Makers of Explosives' (IME) Safety Library Publication No. 22 were tested in bonfires. The boxes were instrumented with thermocouples, filled with detonators, and placed over a kerosene fire imparting about 16 kilowatts per square meter heat flux for up to 3 hours.

Jan 1, 1997

By Calvin J. Konya

Backbreak behind the last row of boreholes can be a significant problem for blasting operations. Backbreak will interfere with the proper drilling and execution of the subsequent shot and can produce well defined boulders, which will not be broken by the subsequent shot. In order to determine the effect of timing on backbreak, a full scale blast with 6 1/2 inch boreholes was used to test the effects of timing. The test site was a quarry which had suffered from severe backbreak regardless of the blasting pattern or explosive used. One half of the production blast was loaded and initiated using the current technology at the quarry, the other half of the blast was deliberately timed in such a manner as to minimize backbreak. The timing was such to allow for ground movement in one row before the subsequent row fired. The test results proved that the amount of backbreak and flyrock could definitely be controlled with the selection of the proper borehole timing.

Jan 1, 1987

By Michael Louis, Charles Dowding

Concern over construction vibration-induced cracking has led to development of a new approach to vibration monitoring called autonomous crack measurement (ACM) and illustrated in Figure 1. This paper describes the concept as well as sensor performance in the first test house fitted an ACM system. Response of three cracks in this concrete masonry unit (CMU) house was measured as part of the system verification. ACM employs a single sensor that measures both weather-induced micrometer changes in crack width and those produced by habitation and ground motioninduced vibration. This comparison is displayed in real time via the Internet without human interaction. Graphic display through the Internet provides a new pathway for communication with the public. Such visual comparison of changes in crack width provides a simple alternative to the present system of comparison of measured and allowable vibration time histories. Measurements reported herein show that weatherinduced response of cracks is greater than that caused by presently allowable construction-induced vibration.

Jan 1, 2003

By Virgil J. Stachura, Larry R. Fletcher

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine which resulted in smoother highwalls. The highwalls were smoother due to reduced overbreak and inherently safer due to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delay intervals which changed the effective delay pattern geometry and the direction of burden movement. Three combinations of blast delay intervals in the highwall holes were tested: 1) 50 ms longer than the nominal design, 2) 50- and 100-ms longer delays in the nearest two rows that form the highwall, and 3) 100 ms longer than the nominal design. The mine's nominal blast design was a flat vee formed by 17-ms surface delays between holes and 42-ms surface delays between rows, with 200-ms in-the-hole delays. All three test designs produced highwall improvements over the nominal design with only occasional exceptions because of geologic variations.

Jan 1, 1985

By Earl C. Hutchison, Gene Smith

Extensive blasting was required to construct an underground tunnel for a 90 inch sewerage relief line. The tunnel and required excavation extended under an upper middle-class residential area in Atlanta, Georgia for more than a mile and a half and required the use of more than a half million pounds of explosives in the immediate vicinity of houses and residential apartments valued at more than 16 million dollars. Other houses and property valued at more than 80 million dollars were within range to claim blasting damages. An effective blasting damage control program was carried out which limited the number of blasting damage claims to less than 2-1/2% of the total number of potential claims. All but three of the small number of blasting damage claims which were made were effectively denied without any resulting legal actions and less than $3,800 was paid for settlement of the three claims.

Jan 1, 1981

By Lyall Workman, P D. Katsabanis

Energy released by the explosive is typically partitioned in brisance, heave and losses. The fact that energy released in the P-V expansion curve below a certain point is lost has resulted in the concept of available energy. Through simple calculations it is shown that energy released at pressure levels thought to be low, amounts to a significant proportion of the total energy value. Furthermore, throw calculations indicate that the assumed loss of that part of energy does not justify practical results. Loss of energy at the low pressure levels may also not be justified from the fragmentation point of view as pressure levels below 1 kbar are enough to extend radial fractures around a borehole. Finally the equation used for the P-V behaviour of the explosive gases is important in throw calculations. Simplified approaches may not reproduce the performance of the explosive which is not characterized only by its energy content.

Jan 1, 1998

By Larry R. Fletcher, Virgil J. Stachural, Matthew N. Plis

The Bureau of Mines is conducting research on blasting methods that reduce highwall overbreak and the associated rockfall hazards. This paper presents the results of a series of tests to improve presplitting at a western surface coal mine. Reductions in overbreak were achieved by decoupling and/or repositioning the main explosive charge in the 10-5/8 inch presplit blastholes that formed the highwall. Blast designs are presented by the authors for 1) repositioning the explosive charge from a weak rock layer to a stronger rock layer, 2) decoupling with cardboard tubes in the toe region, and 3) suspending bagged powder at intervals along the length of the blasthole. About the same total quantity of explosives was used in all three test designs. It was readily apparent from periodic visual examination and photographic surveys of the highwalls that the amount of rockfall was reduced, and with a longer delay before rockfalls began, in all test areas.

Jan 1, 1991

By Jack Eloranta

Transmission of sound through the atmosphere is affected by local conditions. Anecdotal accounts of the sound of cannon fire traveling great distances go back to the Civil War. The Royal Society published a paper near the turn of the century concerning the reports from the cannons fired in London at the funeral of Queen Victoria. Early computers were used by the U.S. Army at Aberdeen in Maryland in the 1950’s to model airblast problems during munitions demolition. Today’s blaster has to have access to weather information beyond a simple local forecast. Surface winds, winds aloft and temperature profiles have a dominant role in neighbors reaction to blasting. Many ground vibration complaints are really airblast complaints. Blasters who maintain ground velocities under . 1 inches/ second are often perplexed by complaints from distant neighbors, even when local monitoring shows airblast to be under 110 dB. This paper will help the blaster identify warning signs of high airblast conditions.

Jan 1, 2000

By FM Murray

SAFEX International is a global organisation with more than 85 members, all of whom are manufacturers of explosives. On joining each member signs a declaration saying that they are willing to exchange information with regard to any accidents or near misses they may have in order to prevent the recurrence of the incident. SAFEX International was formed 50 years ago in Europe and has now built up a database of more than 700 accidents in the explosives business. Once every three years, an International Congress is held in which members address specific safety themes associated with the explosives industry, and also give details of "what went wrong?", "why?", and lessons learned. The next Congress will be held in Amsterdam between the 29th May and the 1st June 2002. This paper describes the operation of SAFEX International, which is dedicated to the international exchange of experience on industry connected accidents of the explosives business.

Jan 1, 2002

By Marco Antonio Falquete

Conventional detonators and blasting caps make use, as igniters, of flame-shock-, andfriction-sensitive primary explosives, such as lead azide, lead styphnate, mercury fulminate, etc, most of them severe toxic and environmental contaminants. Sensitivity of primary explosives is one of the main causes of injuries and fatalities in explosives industry and in field applications. Intense research for a reliable, safe, and environmental-friendly non-primary-explosives detonator was conducted by the industry in the last years. A new detonator is presented, containing no primary explosive, employing only environmental-friendly substances while keeping reliability of performance. A series of performance tests is executed in prototypes of different output energies, including initiation by flame, shock tube, thermo tube (IBQ’s proprietary spark-generating tube, presented at 2005 ISEE Conference), energy transfer reliability, and extreme environmental conditions (according to MIL-STD 331B, test C1 standards). Results are compared, when pertinent, with standard blasting caps of different energy outputs, and with standard primary explosives.

Jan 1, 2007

By Stephen Mansfield, Nathan West, El Khalil Seyed

In October 2017, a multi-bench failure occurred in the east wall of the Guelb Moghrein copper and gold mine in Mauritania. The failure extended 100 m (328 ft) vertically and horizontally and resulted in the sterilisation of ore, but no equipment or personnel were put in danger. The remediation plan successfully removed the failed material and the cutback resumed to a modified pit design, leaving ore reserves behind. In 2021 after completion of mining in another part of the pit, a plan was formulated to develop a narrow cutback behind the failed wall and recover the sterilised ore. Infill drilling defined a resource of approximately 2.9 Mtonne (3.2 Mton) of ore at 0.78% Cu and 0.67 g/t Au at a strip ratio of 5.5:1. The high strip ratio meant that it was necessary to mine thirteen benches of waste, or 156 m (512 ft) vertically, over a two-year period before reaching the first ore, with the cutback only being economically viable if all ore could be depleted at the end of the third year. The high economic risk of the project required a holistic approach to mitigate the risk of another wall failure, by addressing the following areas: 1. Pit Design: with help from an external Geotechnical Consultant, the pit design was optimised to include increased factors of safety, reduced stress points, lower overall slope angles and straight lined walls were replaced with curved walls. 2. Geotechnical Management: the site Geotechnical Superintendent worked closely with an external Geotechnical Consultant to better understand the structural geology. Slope monitoring was improved through an expanded network of prisms, regular in field inspections and the use of a slope monitoring radar. 3. Drill and Blast: new drill and blast designs were developed from first principles, consisting of production, wall control and presplit designs. Blast master polygons and bench development sequences were developed with consideration of the structural geology and the influence of the initiation designs. 4. Mine Operations: improving operational discipline was a critical factor that ensured the accurate execution of drill and blast designs and excavation to bench levels and pit limits. This holistic approach has enabled the safe development of the cutback down to the 936 RL (relative level), two benches below the point at which the previous wall failure occurred. Extraction of ore has occurred from the 960 RL, and due to faster than planned excavation rates, the cutback is expected to be completed ahead of schedule.

Jan 21, 2025

By Paulo Couceiro, Manuel Lopez Cano, Carlos Rodgriguez Calvo

Apart from its difficult execution, underwater blasting is one of the most critical operations of the blasting techniques; mainly because of the ground vibrations - normally associated with low frequencies -, destructive hydraulic shock waves, the difficult coordination, and high costs. To solve these challenges during the underwater blasting on the expansion program for the Panama Canal “Widening and Deepening of the Pacific Entrance and the South approach Channel to the Third set of Locks of the Panama Canal”, a new method to blast using bulk explosive, developed by MAXAM, was used. The project was successfully executed, and more than 800.000m3 were blasted in less than 5 months, jointly with the biggest underwater drilling platform ever build, the Yuan Dong 007, with ten hydraulic drills on board guaranteeing a high production, excellent fragmentation result, total control of the vibration levels, no complain of the neighborhood surrounding the area of the project and simple local logistic due to the classification of the main product used (an oxidizer classified as 5.1). That was finally sensitized down in the hole.

Jan 1, 2011