Search Documents

By Jorge Cárdenas, Piero Mejía, Diego Gamarra

The present case study details the solution to a complex situation in a mining operation, involving the challenge of expanding the tailings storage facility in high-criticality areas adjacent to electrical rooms that provide continuous power to the entire mining process, including water pumping and drainage systems. For this purpose, blasting is required to prepare the construction areas for the new expansion facilities. Upon deciding to proceed with blasting, a comprehensive engineering assessment was conducted to ensure operational continuity without impacting the process, while generating sufficient fracturing in the rock mass to allow extraction with auxiliary equipment. Support from specialists through the Technical Assistance area was requested, and a detailed evaluation was carried out through advanced studies. Field vibration studies were conducted to define attenuation models and characterize the rock mass in the sector. With this information, simulations were carried out using predictive and probabilistic models with Monte Carlo methods to select delay charges and optimal timing for reducing vibration levels and increasing frequency levels. With these measures, the three blasts conducted near the Gas Insulated Substation room, which had distances ranging from 30 to 100 meters, produced the following results: • Vibrations; The three blasts conducted at distances of 100, 30, and 50 meters recorded vibration values of 5.3, 40.2, and 9.5 mm/s, all of which were below the maximum vibration level of 50 mm/s set by the projects area. According to the USBM RI8507-OSMRE standard, all values for Peak Particle Velocity (PPV) and frequency were below the permissible limits. • Flyrock; Through filming and post-blast inspection, it was confirmed that the ejections were within the safety zone. • Fragmentation; The results obtained showed a maximum overbreak size of 1.5 meters, allowing the broken material to be moved effectively.

Jan 21, 2025

By Drew Martin

In March 2010 the Boral Linwood Quarry, Adelaide South Australia, implemented the blasting contractors Monte Carlo Blast Vibration Model as part of their blast design process. The Linwood Quarry was developing an area where blasting activities were marginally complying with the statutory vibration limits. Compliance to the statutory limits was only being achieved through the use of small blasts (less than 15 000 T (14 763 ton)) at a high cost to the quarry.

Jan 1, 2012

By Gustavo Huerta Valer, Jorge Cárdenas Miranda, Johan Salas Flores

One of the challenges of mining is the optimization of the blasting process, which has an important impact downstream in the processing of crushed ore in the plant, that is why mining companies ensure the results of granulometry obtained from the blasting process through a joint work with companies specialized in the process of loading with explosives.

Feb 6, 2023

By Norman Paley

A blasting project was undertaken at the Teck Alaska Red Dog Mine in 2005 to 2007 to determine the extent that using electronic detonators could increase Semi-Autogenous Grinding (SAG) mill throughput. The results of that project were reported at the 2010 ISEE Annual Conference. This paper is a postscript to that project and provides the fragmentation resulting from the implementation of a 15% pattern expansion using electronic detonators.

Jan 1, 2012

By Lizbeth A. Escobar, Phol M. Llanos, Maritza Y. Avila

The present research develops the estimation of critical parameters such as the distances and times between holes to avoid failure due to dynamic pressure in electronic detonators based on the near-field ground vibration model of Holmberg & Persson and the hydrodynamic model of Neyman.

Feb 1, 2020

By Weiying Zeng, Shouwei Wang, Jinbei Zhong, Xiangdong Meng, Lingtian Meng

"Due to a drainage problem, the Lanzhou to Chongqing high-speed rail line had been out of service during the 2015 wet season, so a drainage tunnel is to be constructed for the line and required to be accomplished before the 2016 wet season. This drainage tunnel is only 5 meters below the line which is in service, therefore blasting vibration needs to be strictly controlled. This paper introduces all theapplied blasting methods, parameters and detonation throughout the entire project, finally bringing in the electronic detonator stagger phase technique and corresponding time difference for detonation."

Jan 1, 2017

By N. Skopak, W. Birch, A. Douglas, C. Johnson

Determining the origins of air overpressure has been a long-debated topic within the explosives engineering community. Historically, it has been accepted that the initial face movement gave rise to air displacement, resulting in an air overpressure pulse. Later research proposed that the air overpressure pulse resulted from the shockwave rapidly propagating through and impacting the quarry face. Most recently, researchers have derived that air overpressure is associated with the gas phase from which a gaseous product from explosives rapidly pours out the quarry face under high pressure. Significant research has strongly indicated that the time at which the air overpressure pulse exits the face fails to coincide with either the arrival of the shockwave at the free face or the initial face movement. Research has consistently shown that the shockwave arrival at the face occurs before the air overpressure pulse leaves the face. Therefore, to best determine which blast mechanism contributed to the initial air overpressure pulse, testing was aimed at verifying the precise time at which the air overpressure exited the faces compared to when the face first moved. This research describes tests using scaled concrete blocks, which provided the ability to control the key parameters necessary for the research to be successfully concluded. Black powder was selected as the energetic material to eliminate the production of the detonation wave while still inducing other gas-producing effects. The components evaluated were air blast arrival times in front of the face, the initial movement of the blast face, the precise initiation time of the blast hole, timing of pressurization within the rock mass (between borehole and face, or adjacent borehole), and the speed of sound in the air. A detailed timeline was created which portrays the actions within the blast to promote an understanding of the sequencing of events. The results showed that the initial face movement occurred at 17.57 milliseconds (ms) while the calculated time at which the air overpressure exited the face occurred at 7.07 ms. The large disparity continues to reaffirm the premise that the origin fails to coincide with the air pressure pulse. Average pressurization through the block occurred at a rate of 341.23 feet per second (104.15 meters per second) which resulted in the gas release pulse being calculated to exit the face between 4.41 and 6.21 ms. This pulse correlates more accurately with the air overpressure origin timing which will be the focus of continued research. Knowing the precise origin of blast-induced air overpressure will assist in being able to better control it through appropriate blast design.

Jan 1, 2024

By Diogo Fonseca, José Manuel, Nuno Fernandes, Francisco Monteiro, Andrew Palangio, Blessing Taiwo

This study aims to enhance the integration between blasting and primary crushing operations in quarrying by optimizing the size of oversize and bypass fragments, ultimately reducing energy consumption. Using simulations of multiple blast rounds at the dstgroup aggregate quarry in Portugal, the research seeks to refine blasting practices and improve crushing efficiency. Part 1 of this study, presented at the International Society of Explosives Engineers' 51st Annual Conference, introduced a baseline framework for assessing the compatibility between blasting outcomes and crusher requirements. This methodology was applied to two blasting rounds, revealing discrepancies between expected and actual fragmentation results. The assessment raised key questions, including the root causes of fragmentation mismatches and the identification of controllable parameters that can be adjusted to align the particle size distribution (PSD) with the crusher’s optimal input range. Based on these findings, six key modifications were proposed to improve blast performance: (1) reducing the drill and blast pattern to limit boulder formation in the overlapping regions of hole influence, (2) increasing both the size and length of stemming material to enhance energy confinement, (3) decreasing subdrill depth to prevent toe burden issues from toe deviation, (4) modifying inter-hole timing to relieve back hole burden, and (5) improving drilling accuracy. Part 2, presented at Fragblast 14, explored advanced modifications to the initial blast design. The first adjustment was reducing subdrill and altering stemming material resulted in an 11% reduction in D80, a 19% decrease in maximum fragment size, and a 21% improvement in blast fragmentation efficiency. These changes shifted the PSD by 15% closer to the crusher compatibility envelope established in Part 1. Despite these improvements, boulder generation persisted in the front and back rows of the blast. This third part of the study focuses on implementing the remaining recommended modifications from Part 1 to further enhance blast efficiency and ensure crusher compatibility. The findings contribute valuable insights into the benefits of integrating blasting and crushing optimization strategies to achieve more consistent and efficient fragmentation outcomes.

Jan 26, 2026

By Peter Dare-Bryan, Will Hunt, Lee Julian

It is well-known that blasting has an economic effect on grade control activities. However, until recently, methods did not exist for measuring the grade control value change caused by the blast. Rules of thumb were the best method to minimize ore loss and dilution, as simulation has been traditionally constrained by time and computer power. Even with these rules followed, an extensive study performed on over 150 blasts showed that the value change caused by the blasts followed a normal distribution – some blasts created value, and some blasts destroyed value. The question naturally asked was “How can we ensure the blast designs are optimized to create value?” Recent advancements in computer power have enabled real-time blasting simulations that create post-blast grade control models before the blast is fired. Understanding what will happen before it happens allows blasters and grade control personnel to iterate designs, searching for the highest value achievable.

Feb 6, 2023

By Joshua Calnan, Braden Lusk, Kyle Perry

This paper presents detailed information and data regarding the load transfer characteristics of Blast Resistant Glazing Systems utilizing two different thicknesses of polycarbonate. A series of triaxial load cells, along with surrogates of identical stiffness characteristics, were placed around the glazing perimeter to directly measure the load transferred to the support system from explosions of varying degrees. The blast loads were developed using an explosive driven shock tube administered by the University of Kentucky Explosives Research Team (UKERT) in Georgetown, KY. Results presented include distribution of loading, maximum load transferred to connections, blast pressure-time data, glazing system deflection-time data, and final performance results of each system. The two glazing systems respond differently to the applied blast loading. Differences and similarities in the load transfer characteristics are discussed. The experimental results are then compared to a commonly used blast resistant glazing system analysis software tool utilizing a Single Degree of Freedom (SDOF) method of analysis for each system. Preliminary results show that currently used models do not correspond well with experimental data.

Jan 1, 2014

By Mark Svinkin

To save time for construction of coal pits, the contractor decided to combine erection of the tower pitheads with digging of skip shafts to the depth necessary for placing proper coal pit equipment. It was obvious that blasts used in shaft faces and lifting machines installed at a lower part of the pithead could excite vibrations of an upper part of the pithead with curing concrete. The contractor was concerned about vibrations of pithead concrete structures and the disturbance of freshly poured concrete in forms at a top of the pithead as a consequence of structure vibrations. The results of a study of the tower pithead structure vibrations from blasting and operating machinery, and effects of structural vibrations on curing concrete are presented. Structural vibrations were measured at the tower pitheads of two coal pits from twelve blasts. Records of horizontal and vertical displacements were superposition of harmonic low-frequency damped vibrations and sporadic high-frequency damped vibrations with a variable frequency. Low frequency vibrations attenuated during 8-13 s after the last delayed blast. Measured values of the natural frequencies of pithead horizontal vibrations coincided with the calculated frequencies of horizontal bend vibrations. An increase of a face depth from 18 to 50 m diminished 16 times horizontal bending vibration displacements of concrete structures. Measurements of vertical structural vibrations from blasting demonstrated increasing of vertical pithead displacements with the rising of structure elevations. This is evidence of the pithead longitudinal tension. The holes with charges were not properly condensed for one blast. As a result of incompact stemming, the blast substantially increased the energy of airborne pressure waves, which triggered natural vertical vibrations of the pithead with high displacements.

Jan 1, 2004

By Ronald W. Roberts

For years, blasters have experienced near-misses, injuries, and yes, even fatalities as a result of the dangerous nature of our business. Yet, some blasters continue to portray the immortal attitude: nothing-would-or-could-ever-happened-to me syndrome. As we all know, that attitude can become disastrous to yourself or colleague(s).

Jan 1, 1996

By John W. Brown

"Adequate dust control in and around rock drills is a problem that must be solvedfor the health and safety of workers running the drill as well as those working around thedrilling operation This paper will discuss the designs available from most drill manufacturers todayand the effort ‘nvolved in keeping them effective on a productive basis."

Jan 1, 1999

By T Duff

This paper describes results from small scale tests conducted to determine the distribution of pressure on target plates when subjected to loading due to the detonation of a buried mine in various media. The tests are conducted by using saturated sand, dry sand, and water as the loading media. Different stand-off distances are investigated. Kolsky bars and pressure sensors are used to determine the free-field pressure - time profile of the output of the charge at any location on the vehicle bottom. For verification of the pressure results at certain distances, the specific impulse measured by utilizing different size round plates are employed. In order to investigate the loading mechanisms, high speed cameras are applied. The small-scale test results can be scaled to full scale by using verified scaling laws.

Jan 1, 2014

By A. Ravi Kumar

A trench is a structure to accommodate fluid carrying pipelines for water, gas, petroleum products etc. Trench serves the purpose to haul the fluids in bulk over long distances safely and economically. Use of pipeline for moving oil and gas was essentially a post World War II development, but now it has acquired its own importance.

Jan 1, 2008

By Patricio González Santis, Jacopo Seccatore

This paper documents drilling and blasting activities from gold mining in Ecuador and Chile. First, are described the outdated and often non-rational techniques employed by miners, to provide a general framework of the current methods. Then, it is shown what can be improved and how the current methods can be modified. Finally, are shown some field applications and the comparisons of the results obtained

Feb 1, 2020

By S. Hosein, W. Birch, C. Johnson

The widespread adoption of electronic detonators has given rise to the development of linear superposition to control the environmental impact on both third-party properties and residents resulting from blast induced vibrations. Linear superposition has become a very effective tool in the hands of blasting engineers and has enabled aggregate reserves to be accessed that once had to be abandoned. This in turn has resulted in more and more complex blasting pattern to be developed that contain multiple rows and multiple decks all with different maximum instantaneous charge weights of explosives. This is then made more complex by having to consider multiple sensitive locations often with different Peak Particle Velocity vibration limits. This paper is a case study of what did happen when a blast was designed that “pushed the boundaries” of environmental blast vibration design and control, without taking fully into account the fundamental geophysical properties of seismic waves. The resulting blast design caused a greatly enhanced s-wave to be created in a critical direction from the blast pattern. The root cause being the s-waves from earlier detonating decks in the blast pattern arriving within 2 milliseconds of decks detonating later in the blast pattern. 209 individual decks were fired in the blast pattern of which 41 pairs of decks arrived at the observation location less than 2 milliseconds apart when taking into account the s-wave speed and direction. The lesson to be learned when using electronic detonators to limit ground vibrations from complex blasting patterns, is that it is just not good enough to look at the planned firing times, a professional blasting engineer must also understand the likely interaction of the various seismic wave types created and their combined impact on any given monitoring location.

Jan 1, 2024

By Denard Brandt, Isidro Martinez, Greg Baker, Laura Slattery, Teddy French

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority.

Jan 1, 2010

By Raden Haris Handayana, Jihan Farhan Lubis, Milia Putri, Tengku Deli Hamonangan Hasibuan, Sani Salahudin

An environmental issue that must be controlled from coal overburden blasting near the structure is ground vibration. Damaging ground vibration is the effect exerted from residual energy from blasting that does not work to fracture the rocks. Sebuku Tanjung Coal is a coal mining that operates T3 Pit adjacent to the High Voltage Tower. This structure is included in the Class 5 building with a maximum Peak Particle Velocity (PPV) of 40 mm/s. The shortest distance from the blasting location to the structure is 105 m. The initiation system used is electronic detonators combinate with emulsion as an explosives type. In Indonesia, the government regulated vibration limitation on SNI 7571:2010. The blast outcomes targeted are PPV below 40 mm/s, fragmentation size <80 cm for Excavator Komatsu PC-2000, and digging time <12 seconds. In this paper, the blast design was engineered by conducting Signature Hole Analysis for optimizing delay timing configuration and Scale Distance regression analysis to determine optimum charge weight per delay at the blast site. PPV results from 30 blastings achieved 100% below 40 mm/s with the range of about 1.773-30.250 mm/s. The deviation between PPV prediction to PPV actual is less than ±18% which provides the blasting with electronic detonator resulting in good PPV prediction for controlling vibration. The average fragmentation size (D80) is 55.81 cm in the 1st layer and 54.81 cm in the 2nd layer. The average digging time is 10.30 seconds in the 1st layer and 10.12 seconds in the 2nd layer.

Feb 6, 2023

By Kaushik Dey

Bord and pillar is the most predominant method of wining of coal in Indian underground coal mines. Development heading in coal mines often encounters roof stability problem and results in roof overbreak. Research on this reveals that the blast-induced ground vibration may have significant contribution in roof overbreak, especially, when solid blasting is carried out in the bord and pillar method. Solid blasting, in general, is associated with higher charge confinement due to lack of free face and generates higher ground vibration, which in turn results in excess overbreak.

Jan 1, 2008