Search Documents

By Oldrich Machacek, Gary R. Eck

The underwater detonation test method has been long recognized as a useful tool for the evaluation of the energy release and relative effectiveness of commercial explosives. In this study, underwater energy tests were performed for emulsion and watergel commercial explosives in comparison with ANFO. Heavy ANFO type blends based on emulsions and watergels were also investigated under and without confinement.

Jan 1, 1990

By John J. Ridgeway

Habits take us where we were yesterday and attitudes tend to keep us there. Until recently, little had been accomplished to improve conventional explosive energy for use offshore. But with the special requirements of the Offshore Oil Industry, and particularly in the North Sea, most equipment, products and services must be specialized as well. Previous attempts to excavate a trench for a sealine in surf areas had been impossible to accomplish. But with the application of safe, controlled explosive energy, an impossible task to accomplish yesterday has now become a reality. Explosive energy, often overlooked as a convenient and economical offshore tool, excavated a clean trench underwater for a 40" sealine at Djeno in the African Congo recently.

Jan 1, 1977

By Mike McGill, Stephen Chung, Dale S. Preece

Cast blasting can be designed to utilize explosive energy effectively and economically for coal mining operations to remove overburden material. The more overburden removed by explosives, the less blasted material there is left to be transported with mechanical equipment, such as draglines and trucks. In order to optimize the percentage of rock that is cast, a higher powder factor than normal is required plus an initiation technique designed to produce a much greater degree of horizontal muck movement. This is a significant change from normal blasting practice where fine fragmentation and sufficient muck movement were the prime requirements to permit efficient excavation.

Jan 1, 1994

By B Mohanty, R Yang, M Leblanc

A total of 33 blasts in the pillar recovery program at INCO-Crean Hill has been investigated by means of an extensive set of diagnostic techniques. These included, borehole deviation measurements, stope cavity survey, near-field seismics in both rock and backfill, in-hole VOD and fragment size analysis. The 200 mm diameter VCR blasts employed a variety of explosives types (ANFO, slurry and ANFO/Polystyrene) and deck sizes. The objective of the investigation was to control dilution and backbreak through optimal choice of explosive type and charge weight, without exceeding vibration limits in the adjacent backfill or causing significant degradation in fragmentation.

Jan 1, 1995

By David Willock, S. Singh, Michael Glogger

The efficiency of the loading system in a mine depends upon the characteristics of the muck pile, the loading machine specifications and the loading practices. The focus of this paper was to look specifically at the size distribution of blasted material, and to quantify its effects on loader productivity. A scale model of LHD was designed and fabricated to represent machines currently employed in the industry. The experiments were performed using crushed Gabbro, which was mixed in various proportions according to Rossin-Rammler size distribution to give five different characteristic particle sizes and five different size distribution constants for each characteristic particle size. The effect of the size distribution constant on peak and mean penetration forces, work done and bucket fill factor was examined. In addition, the influence of mean particle size, 80% passing size (D80) and % oversize on the penetration force and bucket load was investigated.

Jan 1, 2001

By Harry Verakis, Thomas Lobb

This paper is a summary and an update of the underground mine blasting accident investigations and studies previously conducted by the Mine Safety and Health Administration (MSHA) and the former US. Bureau of Mines. Blasting accidents are usually a small percentage of the total number of mining accidents. However, blasting accidents continue to occur and the severity of these accidents is disproportionately high with respect to other types of mining accidents. In 2000, about 5.7 billion pounds of explosives were produced in the USA. The mining industry consumed the greatest portion of explosives manufactured for blasting with about 67 percent used for coal mining. Metal and nonmetal mining operations account for about 23 percent of the use of explosives. The use of permissible explosives in underground coal mines continues to decline (3,373,069 pounds for 2000).

Jan 1, 2002

By Jaime Huidobro, Mervin Austin

The effect on an explosive column of the sharp transient stress waves generated during the earlier detonation of adjacent blastholes is of paramount importance to explosives users. Some explosives will sympathetically detonate under these stresses. Others may suffer a transient desensitization, arising from a temporary increase in the density of an explosive beyond certain limits and persisting until the explosive mass relaxes back to the original density. Some explosives are so adversely affected by these stresses that the product suffers immediate and permanent loss of sensitivity. These effects can be clearly seen while blasting in tough conditions such as burn cuts or wedge cuts and in materials, such as coals, that propagate shock waves well.

Jan 1, 1992

By Bruce B. Redpath, Thomas E. Ricketts

Scaling laws commonly used for describing or predicting blast motions generated by conventional arrays of blastholes are dimensionally incorrect. The scaling of distance by the cube root of charge weight is correct only for spherical charges, and scaling by the square root of charge weight is incorrect for any charge configuration, although both approaches may result in empirically useful formulas for a limited range of charge sizes. Analysis of motions generated by a large set of underground blasts shows that scaling distance by the square root of the linear charge density, which is dimensionally correct for a cylindrical borehole, yields much more consistent results than the traditional scaling rules. Further, this scaling law is valid right up to the free face of the burden. A significant result of this work is that the peak particle velocity for an array of blastholes is primarily dependent on blasthole diameter and not on total charge weight or maximum explosive weight per delay, which are the commonly used parameters for scaling seismic amplitudes generated by conventional blasting arrays.

Jan 1, 1987

By Frank Lucca

This paper includes research and investigation into blast design and blast optimization for vibration control in municipal and tight blasting situations, where specifications were extremely stringent. The paper is written for the field blaster to understand and develop blast plans based on field conditions. The paper includes blast design considerations, utilizing seismograph arrays to check and predict vibration results, and problems encountered in vibration monitoring in extremely tight situations (0-20 feet). Blast vibration frequency, acceleration, peak particle velocities, and relative displacement are discussed with effects in the near and far fields and blast designs utilized to stay under limits. The paper also discusses using the latest in technology for blast design to control vibration. Equipment includes 2D and 3D laser profiling systems, digital video, fragmentation analysis, seismograph arrays, and borehole tracking devices. Other topics are discussed such as public relations, working with regulatory personnel, unions, and other project consultants, and the problems associated with municipal blasting situations, such as, flyrock and proximity of other personnel and equipment on the project.

Jan 1, 2004

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By J P. Tidman

The demand for more data on the detonation properties of commercial explosives grows as blasting becomes a more exact science. Proper use of this information by blasting engineers depends on the appreciation of the assumptions and limitations inherent in calculating energies and pressures of explosives. The strength of an explosive is usually a calculated energy value derived from a model of the explosive. The model may be simple or complex, depending on the thermo-hydrodynamic assumptions made. The calculated energy and pressures of commercial explosives are sensitive to assumptions about their reaction products. The equation of state describing the reaction product gases, the treatment of solid reaction products (e.g. reacted calcium and sodium nitrate and aluminum) and the reaction time are examined to show the variability of calculated results as a result of different assumptions. These same models of explosives also serve to explain phenomena of explosives such as the effect of charge diameter on V.O.D. (and strength) and decoupled explosives.

Jan 1, 1981

By Lina Lopez, Jose Sanchidrian, Jean Du Mouza, Essaieb Hamdi

This paper evaluates the actual energy delivered by the explosives used in the fragmentation of rock during blasting vs. the available theoretical explosive energy. The evaluation of the fragmentation energy of the blast is first done. Fragmentation by blasting can be seen as a process in which creation of new surfaces within the rock mass is made by generation of new cracks or extension of pre-existing ones. From this idea, the fragmentation blast efficiency can be assessed as the fraction of the available explosive energy used for creation of new surfaces. The evaluation of new cracks area created by the blast is based on the SIMBLOC methodology and the corresponding fragmentation energy is then obtained by the Griffith theory. Secondly, the amount of energy delivered down to a certain pressure or volume along the detonation product expansion process, given by the useful work, is calculated. This is done by first determining the CJ state of the reacted explosive and subsequently performing an adiabatic expansion calculation of the detonation products from that state. W-Detcom code has been used for the calculations using the BKW equation of state with the Sandia parameter set. The fragmentation energy and the useful work are calculated for blasts performed in two mines in Spain. Multiple regression is applied to the results in order to give an assessment of the better description of the explosive energy .

Jan 1, 2002

By Scott G. Giltner, Paul N. Worsey

During the short duration of an explosive blast, many events occur which are too quick to be detected or observed in detail with the naked eye or by normal photographic techniques. Through the use of "hightech", high speed video, many of these events can be observed, instantly played back and recorded for later use. The use of a Spin Physics SP 2000 Motion Analysis System at a blast casting operation is presented. The variable range of recording speeds offered by the SP 2000 allowed it to be used for examination of different areas of blasts. At its maximum full frame rate of 2000 frames per second the SP 2000 can easily pick up the flame front as it travels down a nonel tube and the flash from the surface delays as they fire. The system was used for a variety of tasks including, but not limited to,the determination of delay accuracy to within 0.5 ms, the velocity and trajectory of the faces during blasts, and pinpointing geological problem areas. The effectiveness of the system as used on site is discussed along with detailed method of set up, recording, playback and data processing. Other details including site specific environmental and lighting problems are also covered.

Jan 1, 1986

By Wood Marcum, Gary McLemore, Randall Franklin

Description of Project: Nelson Brothers/Walter Energy (Choctaw Mine) Pre-Split Wall. Walter Energy – Choctaw Mine is a multi-seam surface coal mine in Northwest Alabama.Pre-splitting is the standard procedure of the Pratt Seam, which is the top seam (186 feet deep) as shown in the photo at Choctaw Mine in Parrish, Alabama

Jan 1, 2013

By Michael Weaver, Dale Ramsey

Description of Project: The National Gateway Clearance Initiative is an improvement program to achieve a minimum of 21 feet of vertical clearance along CSX Transportation Inc’s (CSX) rail corridor so that double-stacked intermodal railcars can be transported between mid-Atlantic states and their ports to midwest markets.

Jan 1, 2014

By Wm. Reisz, Raphael Trousselle

We are now well into our second decade of commercially available electronic initiation systems. Over this time, the technological advances have made electronic systems a very practical option for a wide variety of blasting applications.

Jan 1, 2011

By Roger N. Prescott

This report presents a new process in delay blasting with the use of ANFO and slurry explosives.

Jan 1, 1977

By Roger L. Keller, John Dean Smith

The Amax Coal Company's Ayrshire Mine in Southern Indiana is faced with one of the toughest blasting applications concerning vibration in the nation. As a means of maintaining regulatory compliance the operation elected to exercise the option of frequency analysis. A site-specific computer processing program which suggests ideal delay interval ranges for the lowest vibration was utilized.

Jan 1, 1987

By Greg Quinn

After a long week of work in Colorado Springs this past July, I was looking forward to flying home to start a long anticipated family vacation. As I grabbed my seat on the plane, a man sitting next to me innocently inquired, to the row as a whole and not to me in particular, “I wonder what the weather will be like in Phoenix”? To most people, this is a common (maybe the most common) topic of casual conversation. To a meteorologist that just dealt with six thunderstorm delays at a major golf event over 4 days, well, lets just say the smirk on my face said it all. After giving my flight mate a detailed forecast and a short explanation on why I would know such information, I sensed, correctly, the inevitable follow up question was coming. “Why would you need a meteorologist at a golf tournament?”

Jan 1, 2012

By A. W. (Sandy) Neilson

Whether you are a general contractor who hires subcontractors to perform blasting work or you have your own blasting crew, it is extremely important to understand how Business Liability Insurance works, regardless of who is ultimately providing the coverage. If close attention is not paid to the limitations and preblast survey requirements under most policies that provide blasting coverage, you could find yourself facing an uninsured loss.

Jan 1, 2002