Search Documents

Three high-grade limestone ores (CaO content over than 53 %) with different geological origin have been characterized for the synthesis of aragonite precipitated calcium carbonate. Limestone ores examined in this study showed different crystal particle size that cause difference in disintegration degree and surface area of the synthesized slaked limes. The limestone ore with smaller crystal particle size showed higher disintegration degree and also yielded slaked lime with smaller surface area, which is good for the synthesis of aragonite precipitated calcium carbonate. The synthesis of aragonite PCC using the limestone with a small crystal particle size was yielded needle-shaped aragonite with the aspect ratio of about 14. Keywords: limestone, lime, slaked lime, precipitated calcium carbonate, aragonite, accelerated carbonation

Sep 1, 2012

By S. S. Lu

In sodium oleate and salicylhydroxamic acid systems, sequence of floatability of three sulfate minerals is: barite>celestite>gypsum, in lauryl amine system is: gypsum>celestite>barite. XPS and infrared spectrum analysis are used to find that it is chemical reaction between sodium oleate and three minerals, physical adsorption on the surface of minerals for lauryl amine, and it is chelating reaction between salicylhydroxamic acid and three minerals possibly. Theoretical calculation on chemical bonds in crystal structures of three minerals is carried out, finding that breaking degree of Mn+?O2- in crystal structures of three sulfate minerals is closed related with floatability.

Jan 1, 2014

With the ambitious target of adding another 2,00,000 MW of power generation by the year 2017 in India the demand for coal is bound to grow. The non-coking coal deposits in India are characterized as high ash and difficult-to-wash coals. Quality improvement by beneficiation is almost mandatory due to MoEF notification to use <34% ash coal for all power plants except those located at pithead. Most of the coal washeries in India are based on wet process, where the coal fines are allowed to settle in thickeners. The coarser particles settle faster leaving the fine particles suspended for longer period. The dispersed fine coal particles contain some surface charge, which leads to the development of electrical repulsion between the particles, and as a result of this, the suspension becomes more stable. In order to destabilize the colloidal suspension, flocculants are usually added, so that the settling rate of the fine particles also increases. These flocculants are of cationic, anionic and non-anionic depending upon the type of charge released when dispersed in water. The flocculants may act partly for charge neutralization and partly for inter particle bridging and electrostatic patch formation. The effectiveness of any type of flocculants depends upon the molecular weight and charge density of the polymer. The paper discusses the settling behavior of non-coking coal fines suspension by using different flocculants. Keywords: floculent, coal fines, sedimentation rate, effluent

Sep 1, 2012

By Kr. J. Dedelyanova

Selective flocculation of iron minerals could improve the economics of high intensity magnetic separation as concomitant process. When the minerals are finely disseminated is necessary a finer grinding to be applied which generates a lot of slimes. The HIMS is not enough efficient for particles below 20 microns ? territory where the selective flocculation is already well known industrial practice, so the combination of these two methods of beneficiation can bring a higher grade at high recovery to be achieved. The dynamics and selectivity of the precipitation process is studied in batch tests with flocculant starch and dispersants sodium silicate and sodium hexametaphosphate. The influence of preliminary conditioning with nitrogen acid at pH 2 before flocculation is also investigated. Flowsheet including these two methods is tested and the distribution of iron is shown.

Jan 1, 2014

By G. Y. Zhou

During Zijinshan copper heap bioleaching, pyrite was leached in plenty resulting in high ferric concentration in solution. It has affected bioleaching and extraction processing greatly. It results much acid and iron in solution and bad effect to extraction processing. The paper studied the influence factors in the course of pyrite leaching and ferric ion chemical oxidation, especially studied the redox potential for copper bioleaching so as to find key factors affecting the dissolution difference between chalcocite and pyrite. The results show that the redox potential is important factor. Copper and pyrite leaching rates are 95% and 11% respectively and there is great dissolution difference between them at redox potential 700 mV (SHE). During pyrite bioleaching, the indirect action of bacteria gives priority to bioleaching cooperating with the direct attack of microbial cells attached to the mineral surface. Redox potential is determined by ratio of ferric and ferrous, ferric in solution was supplied by the way of oxidation of T. f bacteria, sufficient bacteria concentration and active character were two vial factors of controlling redox potential. It is indicated that copper can be selectively bioleached during copper bioleaching by controlling redox potential of bioleaching. The conclusion will provide theoretic foundation on balance of acid and iron during bioleaching for copper of higher S/Cu ratio. The experinment proved that bacteria activation was decreased on condition of both low pH value and intermittent aeratation during bioleaching. It resulted that the oxidation velocity of ferrous ion was decreased and redox potential was controlled. The dissolution of pyrite was depressed. It would be possible to actualize selective leaching of secondary sulfide copper ore during bioleaching process.

Jan 1, 2014

By I. V. Shadrunova

Annually it is formed more than 95 Mt of clinkers in iron and steel industry of Russia, including 79 Mt of clinkers in blast-furnace, steelmaking, foundry and ferroalloy productions. Complex development of clinkers will provide not only extraction of valuable components, but also preservation of ecosystems. Processing of solid slags is realized, as a rule, in a cold condition by mechanical methods only including stage-by-stage crushing of slag on devices, working on principles of compression and shift (jaw and roll crushers). However it doesn?t provide the complete extraction of metals from clinkers. The intensification of decomposition, in our opinion, can be provided under the use of the devices working on a principle of free kick. At such influence on a material, its destruction occurs on micro cracks, sides of cohesion that is there is a selective destruction of the components possessing various resistances to impact. Decomposition of a piece on the basis of free kick about a material or metal is realized in centrifugal-shock crushers and mills of research-and-production association ?Ural Center?. The share of the joints sharply lowering the efficiency of enrichment thus is minimal. The efficiency of application is proved by morph-metrical measurements with the help of system of image analysis ?SIAMS-600? and physical-mechanical tests of clinkers and their components (impact strength, micro hardness). The experience of application the devices of centrifugal-shock crushing for processing clinkers in blast-furnace, martin and converter productions of Open Society MMC, clinkers of rough-edged copper melt of Joint-Stock Company "Karabashmed" and aluminium clinkers of Joint-Stock Company « Samara plant of aluminium alloys » has allowed to confirm the efficiency of application these devices for selective decomposition of metallurgical clinkers and the opportunity of using clinkers as resource of ferrous and nonferrous metallurgy.

Jan 1, 2014

By L. A. Vaisberg

"Mining processing plants are the most high-performing industrial enterprises in the world economy system. Even at an average-scale mining enterprise, the grain-size separation equipment continuously processes 105 to 106 dissimilar mineral particles per hour. In separation by physical properties, their number increases by at least 10 to 50 times. Mathematical modeling of such a high flow of discrete particles is carried out using two different approaches: the discrete-particle and the phenomenological methods. The calculations demonstrate the possibility of handling big data when describing the processes of separation of granular material. INTRODUCTION The interest to the screening process and the process of formation of new screen designs in Mekhanobr is traditional since the moment of its foundation. It is symbolical that the first publication of the Mekhanobr proceedings in 1924 was the monograph dedicated to screens and screening products as such, which was the first one in the world at that moment. It was a book of Prof. L. B. Levenson, one of the founders of Mekhanobr, who headed the Technical Bureau of the Institute. Vibratory screening is the most mass process in the technologies of solid minerals processing, which determines significantly the energy demands of crushing and grinding cycles, and at some enterprises determines the quality of the final product, for example in case of crushed stone, coal or abrasive materials production. The general understanding and simulation of the process of poly-dispersed granular materials vibratory screening was developed at several conceptual levels taking into account the features of classification of materials with different size and density.Considering the real industrial processes of vibration screening, it shall be noted that at the sieve surface of the screen in the initial part of the deck the classification in a thick material layer (in natural conditions) occurs, which further transfers to a thin layer (free movement). In the process of screening of light minerals, for example coal or metallurgic feedstock, screening is mainly performed in the thick layer."

Jan 1, 2018

By E. Pourjenaei, P. Ghobadi

High Pressure Grinding Roll (HPGR) is efficient equipment in comminution process. HPGR could be a good option for preparing ball mill feed at the first stage of grinding due to its high efficiency and low energy consumption. Closing with a screen, these mills are utilizing as one of the principle parts in mineral processing industries, especially for iron ores. Recently, HPGRs are working as primary mills at 4 developing lines in Gol-e-Gohar Iron Ore Processing Complex, Iran. Different mechanism of particle crushing in compare to the other tumbling mills makes the HPGR as certain equipment with its own particular controlling parameters. Hydraulic pressure, roller speed and level of material inside feeding hopper are the most important variables influencing grinding efficiency of the HPGR. To figure out how they impress the process and operation situation, different industrial tests were carried out and the best result (d80 about 8 mm for HPGR discharge) was achieved at 180-190 bar pressure (P), 300 rpm speed (S) and 50% of hopper level (L). It is worth noting that this finding has been observed through past pilot test too. We also used design expert method (DX7 software) to develop the best design and analysis the test results, as well. According to the mechanical restriction of HPGR and process limitation in the plant (based on the industrial results), we adjusted value of each parameter in a logical range. Therefore, 20 industrial tests were conducted, as DX7 recommended, and the various impacts of the parameters and their interaction were identified based on statistical analysis. As the authors expected, it was revealed that after presser, roller speed is a critical variable because of its significant role in residence time of the particles between the rollers. The function below has been determined to explain the relation between different parameters and the response.

Jan 1, 2018

By Baidyanath Mandal

Technology in the solid-liquid separation industry has evolved rapidly during the last fifty years and from the beginning, DIEMME Filtration has played a very important role in this evolutionary process by developing innovative solutions, which are used for a diverse range of industrial applications. Since the last decade, we find more and more examples of filter presses employed in the mining & mineral processing field, where high performances in terms of productivity, dewatering capacity and mechanical strength even in extreme working conditions are required. Mainly the requirement of such high quality equipment comes from the Process, however in few cases the reason could be linked with the environment. For stringent process applications like Mineral Concentrates dewatering & leached Slurry Filtration, it requires a high quality & extremely reliable equipment. In these applications, since many years industries are achieving the desired result by using Diemme Filter Presses. Also, recently, due to stringent environment practices are been applied globally, industries needs equipments which could dewater a high amount of residues / tailings with minimal moisture content in the filtered cake. In comparison to all the conventional dewatering equipments, Diemme Filter Presses are most efficient for these kind of product & applications. Diemme Filtration is a highly professional & technological company with several decades of experience in designing equipment for mineral processing. We take up each project as separate & design and manufacture equipment based on individual process or project requirement. This presentation will be focused on the Solid-Liquid separation technologies & equipment Diemme Filtration offers to the mineral processing Industries. It consists of Diemme?s History, Global Network, Technologies & Expertise, R & D Capabilities, Manufacturing Range, Some Applications & results on different mineral processing. Keywords: solid-liquid separation, filtration, dewatering, filter press

Sep 1, 2012

By A. V. Kanarskay?

The research is aimed at involving in the processing of poor platinummetal natural and technogenic raw materials. The purpose of the research is the creation of a multifactorial complex of innovations in the system of ore preparation and separation cycles, which ensure a high efficiency of flotation enrichment of hard-to-treat raw materials. In the usual practice of enrichment, minerals of the platinum group (PGM) of less than 10 microns in size are the source of inevitable process losses. For poor raw materials, it is precisely thin PGMs that are characteristic, their proportion sometimes being almost 100%, and their opening leads to the formation of a large amount of slime, which adversely affects the efficiency of flotation. To reduce the yield of slimes and increase the selectivity degree of the opening of the PGM in the ore preparation cycle, a dry grinding scheme and pneumoclassification of the milling material has been developed to obtain fractions of different fineness, density and morphology of the particles. From 2 to 5-fold reduction in the yield of slurries for various ores has been achieved. The separation cycle successfully tested are: flotation of fractions in separate cycles with a differentiated choice of the reagent regime; preliminary selective flocculation of slime fraction material; use of a new generation of bioreagents for flocculation and flotation. A new approach to subsoil research is protected by a patent. The dependence of the efficiency of biocollectors on the composition of biomineral extract from the processed raw materials, which forms the basis of new reagents, is established. The possibility of obtaining the degree of extraction of PGM, native gold and sulphides from finely ground pre-fractionated poor ores with the use of biocollectors of at least 85% is proved. With conventional reagents, the extraction of PGM is 12-23% lower, with the use of traditional ore-preparation apparatuses, the PGM recovery rate was halved. Methods for the long-term storage and preparation in industrial conditions of biocollector reagents that do not require the purification of waste waters from them have been developed. The developed multifactorial system of intensification of flotation enrichment can be introduced to recovery PGM from tailings of enrichment of titanomagnetite, chromite and copper-nickel ores.

Jan 1, 2018

By Diogo R. Prado, José Aurélio M. da Luz

Drying operation can have a major importance in a mineral processing undertaking. The proper sizing of dryers can ensure the specified dewatering level without energy wastage. However, often the sizing of fluidized bed is done disregarding the actual residence time distribution (RTD) of the particles inside the reactor. In this case it is usual to adopt the average residence time as a design criterion. In this work, we have quantified the effect of residence time distribution on drying, ensuring that a previously adopted fraction of the particles remains inside the reactor for the required time lapse needed for drying. Design criteria such as particulate flow rate and drying time, taking into account the statistical distribution of residence time was studied, matching the thermodynamic and fluid dynamic aspects of the drying process. Experimental tests carried out have confirmed the RTD for a teetering bed as the same for a canonical ideal mixing system. Although the fluidized bed volume using the proposed formulation was higher than that found for the average time based procedure, the efficiency gain in drying has proven advantageous.

Jan 1, 2014

By Yongfu Yu, Xiaotie Wang, Fuguang Zhang, Liping Che

"The flotation process of native Rare Earth minerals such as bastnasite, monazite, mixed minerals of bastnasite and monazite, using the new effective collector Dh was studied in this paper, respectively, and the flotation properties are described. The good qualities of the new collector Dh were revealed through comparing with other collector of Rare Earth minerals. The test results of different ore samples show that at moderate pulp pH (8.5-9.5), Rare earth minerals can be effectively separated from barium, calcium and silicon bearing intergrowth minerals (barite, calcite and silicate minerals) and high quality Rare Earth concentrates can be obtained successfully by the new collector Dh, acid silica gel, turpentine and reagents fitting together rationally. In order to determine optimum technical conditions, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents (Dh and acid silica gel) on the flotation were investigated in the test.Simultaneously, the paper explores the mechanism of the flotation of Rare Earth minerals from intergrowth minerals. The infrared spectra for Dh and Rare Earth cation by analysis in theory shows that Dh formed chelate complex with Rare Earth cation and were adsorbed on the surfaces of Rare Earth minerals. The mechanism of the intergrowth minerals depressed by acid silica gel can be explained as gummy colloid hydrolyzed from acid silica gel which are selectively absorbed on the gangue minerals, making them hydrophilic and depressed, with pulp pH value of alkalescent."

Jan 1, 2003

By G. P. Wong

"In the Inco matte separation process, a slow-cooled converter matte is separated into three main discrete mineral phases: chalcocite (Cc), heazlewoodite (Hz) and a Cu-Ni-Fe alloy. After magnetic removal of the alloy, Cc and Hz are separated by flotation at pH>12 with diphenyl guanidine (DPG) as both collector and frother. High selectivity is achieved in rougher flotation. However, in later flotation stages such as in the middlings circuit, as oxidation takes place, Hz becomes highly floatable, resulting in a very poor separation between Cc and Hz.Starch and dextrin as Hz depressants were evaluated on the middlings circuit feed and showed no positive impact on Cc/Hz separation selectivity. Ethylene diamine tetra-acetic acid (EDTA) extraction showed the existence of abundant surface Cu and Ni ions. The use of triethylene triamine (TETA) or EDTA in flotation did not improve Cc/Hz separation selectivity. Microflotation tests were carried out on pure synthetic Cc and Hz minerals. It was found that Hz did not float in the presence of DPG. However, Hz conditioned with either copper sulfate solution or in contact with Cc floated readily in the presence of DPG. It is concluded that the major reason for Hz flotation in the middlings circuit is due to Cc oxidation releasing Cu ions that adsorb on the Hz surface making it reactive with DPG thus rendering the Hz floatable."

Jan 1, 2003

By R. Venugopal

The paper reviews the development of Mineral Engineering education and training programmes in India. It highlights the major academic programmes and describes the evolution of the curriculum and design of courses in response to the changing requirements of India?s mineral and coal industries. An outline of the efforts needed to sustain and further improve the existing programmes is also provided. Keywords: manpower, mineral engineering

Sep 1, 2012

By S. M. Saghaeian

The studies on the product finer than 12 mm due to crushing and sizing plant of Gol-e-Gohar Iron Ore mine showed which this material contains significant amount of valuable iron minerals. Based on the carried out experimental studies on representative samples of fine hematite iron ore, a processing flow sheet was designed to upgrade iron content. This plant is known as first hematite iron ore enrichment plant in Iran which the dry medium intensity magnetic separators (with magnetic field intensity 4500 gauss and high gradient) has been used. The main objective of the plant is production of high iron product with iron content more than 61% and weight recovery more than 55% from the feed with iron content of 54%. In this plant, at first material are screened by a single deck screen (6mm), then oversize particles is separated at one stage by magnetic separator, while undersize ones at two stages. Based on the results of experimental tests, a final high iron product with iron content of 62.4% and weight recovery 63.9% can be achieved. It should mention which the iron content can be enhanced through increasing the speed of magnetic separators especially at the part of separation of finer iron ore.

Jan 1, 2014

By R. J. Batterham

The science and practice of mineral processing has been driven for many years by the same set of challenges that shape the mining industry ? demand and supply, grades and their decline with time, mineralogy and the need to handle more complex ores, disposal and minimising of wastes and the availability of water, power, skilled labour and the like together with increasing expectations from the community, concerns on sustainability and safety and, as well, climate change forcing a more targeted approach on energy. In this paper, the author builds on previous reviews to the IMPC and suggests that while step changes are long overdue, the unprecedented demand mitigates against drastic changes. That said, the ?Mine of the Future? is already requiring some different approaches.

Jan 1, 2014

By Y. C. Liu

Ningxiang-type iron deposit is a most important sedimentary oolitic hematite deposit in China. Its? detected ore reserves are 3.72 billion tons, which is 73.5% of all detected reserves, and there are about 10 billion tons of prognostic resources. It is considered as the ?poor mine? for a long time be-cause of its difficult prooerty. But based on the ore characteristics of different deposits, the technological characteristics of ore are different with great diversity in ore baring horizon, distribution range, deposit scale, ore petrology, ore mineral assemblage and iron content. Through the study of deposit features and technological mineralogy of different Ningxiang-type of iron deposits in China, and based on industrial types and natural types of ore deposits, we divide different technological types according the technological features of the ore such as mineral composition, particle size, dissemination, occurrence of useful elements and harmful elements, the main physical and chemical properties of mineral and geological conditions of deposits, etc, moreover, propose the different utilization, mineral processing technologies and product schemes for the different types of ore.

Jan 1, 2014

By B. Z. Wu

The ore dressing of tin-polymetallic lean ores is a difficult problem and the research emphasis in domestic nonferrous metals mining field. Through research and tackle key problem,and in order to supply reference in dealing with the same types ores, this paper expatiates the exploiture and appli-cation of six item new technology and technics in ore dressing of tin-polymetallic lean ores. It include the technics of multi-step compounding disposing tailings, grinding step by step, grinding and processing circularly technology, high thickness without circle flotation technology, dispersedly flotation tin step by step technology, exceed fine lean plumbum stibium zinc flocculation flotation technology, the synthetically recovery of waste water after ore dressing technology.

Jan 1, 2014

By Ashish Agarwal

For a correct evaluation of the performance of any process, it is important to reconcile the data gathered in the plant from the material balance point of view for all the streams flowing in and flowing out of the process unit. There are two main approaches to reconciliation of data, which involve minimization of the sum of the squares of: (i) the closure residuals and (ii) the component adjustments; both weighed with the estimated variances of the components. Though, these approaches have served us well, it has not been possible to ascertain if the reconciled values for various components and the split factors obtained using these approaches are truly the best estimates. In this paper, this aspect has been investigated by analyzing pseudo-experimental data of known error structure on size classification of particles in a hydrocyclone. Three types of basic error structures were considered for the measured component values: absolute error, relative error and chi-square error. The error structure was modified by adding a random component of error using normally distributed random numbers corresponding to zero mean and different levels of variance. By carrying out a large number of simulation experiments, it has been shown that in the presence of random errors, irrespective of the basic error structure of data, which is usually unknown, the chi-square error minimization criterion can be used to obtain most reliable results. Keywords: data reconciliation methods, chi-square error minimization

Sep 1, 2012

By Janne Kauppi, Kaj Jansson, Piia Suvio, Saara Hagnäs

"Historically the focus at the mineral processing sites has been to improve the production operations, while little focus has been set on how factors, such as the quality of water used in the process affects the metal recovery. Simultaneously increasing public pressure and water scarcity is driving the mining industry to recycle more water back to the process, which in turn leads to accumulation of impurities within the recycled water. This paper presents a concept for a systematic approach on targeting the impurities that have a negative effect on the metal recovery at the flotation circuit by using a novel solution called Process Water Recycling Plant (PWRP). These plants are designed with specific ore type in mind. PWRP produces cost-effectively process water to different target qualities, especially for flotation purposes enabling higher and more stable flotation recovery. It consists of pre-designed and standard water treatment units for a wide range of volumes. The application-specific configuration of units is governed by the water quality requirements, and can be designed according to specific customer needs. Testing has been carried out in order to investigate, which recycling water impurities affect the different ore types and how the metal recovery in flotation is affected as a consequence of the poor-quality water. The results indicate that every ore type is impacted differently and without a good understanding on how the water quality impacts the process performance, adverse effects on the flotation recovery can occur.INTRODUCTION With a focus on where water is used within the mineral processing, it has become evident that even though water is used in several different processes, majority of the water losses within the site occur at the tailings processing and the tailings storage facility. New tailings management technologies that can increase the recovery of water are actively being developed, but the key to improving the efficiency of water use and reducing the operational risks lies in closing the water loops and increasing the slurry density in the tailings processing. With this shift from conventional tailings technologies towards paste and dry stacking, water efficiency is vastly improved, but it might in turn lead to process water challenges with impurities, reagents and fines being recycled and accumulated within the production processes."

Jan 1, 2018