Search Documents

By Hermann Wotruba, Lars Weitkämper

"Dry coal dressing was popular during the 1950.s and 60.s in many parts of the world. The devices mainly used were air jigs and air tables.The increase in ash and moisture content of run-of-mine coals due to the wide advanced mechanisation of mining mechanisation during and after this period led to that pneumatic devices being unable to treat run-of-mine coals with the desired efficiency. Since the 1960.s almost all new coal preparation plants have been based on wet processes that are highly efficient in terms of coal recovery and their ability to handle damp and sticky run-of-mine coals. (Frankland, 1995)However, water is becoming increasingly costly and the disposal of fine products, containing most of the water, is an environmental concern. There would be significant cost savings and a lower total energy consumption if coal could be cleaned dry. Efficient dry coal treatment would be an interesting solution in desert, arid or cold areas.In Germany one dry coal dressing plant is in operation. The process and the advantages and disadvantages are presented below.Further on new developments in the field of dry density separation of coal are reviewed and analysed. Test results of new dry coal separation methods e.g. new developed air jig and magnetic separator are reported."

Jan 1, 2003

By M. Saghaeian, R. Hejazi, L. Hosseini

The specific surface area (Blain value) of iron ore concentrate entering the pelletizing plant is one of the characteristics most effective on the overall performance of the plant such as producing harder pellets, decreasing additives consumption, and decreasing energy consumption. Therefore, preparing the feed entering pelletizing plant is required. The iron concentrate entering Ardakan pelletizing plant located in Yazd province, Iran bears relatively low Blain value (approx. 1600 cm2/g) which necessitates one stage of regrinding so as to increase the Blain value to more than 1800 cm2/g. Studies were conducted and results showed that HPGR is the best regrinding equipment for increasing specific surface area. Conducting pilot plant tests on the concentrate sample revealed that specific throughput is 181 to 263 ts/hm3 and specific energy consumption is 1.6kWh to 2.2 kWh. Pilot tests also showed that one stage of grinding results in 407 cm2/g to 553 cm2/g increase in specific surface area. Based on these results, diameter of rolls, length of rolls, power consumption and grinding force were calculated to be 1.3 m, 0.9 m, 1276 kW and 13800 kN, respectively. Therefore, an HPGR with a roll diameter of 1.52 m, roll width of 1.1 m, power of 1660 kWh and a capacity of 500 t/h has been selected and implemented in Ardakan pelletizing plant. Industrial performance of HPGR and its effects on the plant study results show that limestone and bentonite consumption has reduced about 60% and 30%, respectively. Total Fe of the final pellet has increased from 65.5-65.7% to 66.2%. Cold compressive strength (CCS) and porosity of final pellets are approximately 292 kg/pl and 20.4, which are in the acceptable range.

Jan 1, 2014

By Dezhou Wei, Cong Han, Shuling Gao, Wengang Liu, Yanbai Shen

The recycling schemes of copper mineral to a copper raw ore produced in China is investigated in this paper, of which is aimed at copper concentrate‘s grade is over 26.00% and recovery is over 90.00%. The primary copper mineral the raw ore is chalcopyrite and the main gangue minerals are quartz, orthoclase, albite, clinochlore and phlogopite. There are four useful metal elements contained in the copper raw ore, which are Cu, Pb, Zn, Au and Ag, and the grade of each is 3.75%, 0.01%, 0.11%, 0.31 and 483.5 g/t. Two floating recycling schemes and its corresponding flotation reagent system were determined. The results show that calcium oxide, sodium carbonate and sodium sulphide were used as regulators, sodium n-butylxanthate was used as collector and terpenic oil was used as frother in two floating recycling schemes are effective. The open-circuit test’s results show that the copper mineral contained in raw ore can be effective collected, and both concentrates gotten through two schemes are up to grade.

Jan 1, 2014

By Hossein Zarei, Masoud Kashani, Mehdi Safari

The feed of flotation unit in Angouran mine, as a part of Iranian Lead and Zinc National Corporation, contains about 34.26% zinc (about 12% Zn sulphide) and 10.14% lead (about 2% Pb sulphide). The grade of Pb and Zn in the final concentrate (rougher+scavenger), under optimal conditions (200 g/ton PEX, 500 g/ton zinc sulfate, 30 g/ton MIBC and pH = 7.5), was 63.18% and 13.01%, respectively, and the total Pb (sulphide-oxide) recovery was about 19% which included 95% Pb sulphide. The grade of Pb and Zn in rougher concentrate step was about 71.86% and 5.97%, respectively, when PEX (Potassium Ethyl Xanthate) was used as collector. While in the presence of PAX (Potassium Amyl Xanthate), the grade of Pb and Zn in rougher concentrate step was 66.8% and 10%, respectively. Tailing of the galena flotation (with 8.48% Pb grade and 34.92% Zn grade under the optimal conditions) was used as a feed for sphalerite and oxide section flotation.

Jan 1, 2014

By Ji Hoe Kwon

Hindered-settling column process has been used for the separation of mineral particles for many years. In this study, a model based on DEM (Discrete Element Method) was used to simulate the movements of particles in a settling column separation process. DEM model is capable of describing the motion of particles and calculating the impact forces between particle and particle, and particle and wall contact under various operating conditions. Drag force, rotation induced Magnus lift force, contact force and the gravitational force acting on individual particles were considered for establishing the mathematic models. The overall motion of the particles in water is satisfactorily simulated by the DEM, and the result shows good agreements with the result of lap-scale experiment.

Jan 1, 2014

By David Morrow

Fly ash is a by-product from coal-fired power stations that is captured from the exhaust gas stream by electrostatic precipitators (ESPs) or bag houses. It is mainly derived from the inorganic components in coal but also contains residual carbon from unburnt fuel (measured as LOI). In the past, nearly all fly ash was sent to landfills or tailings ponds by power generators but this trend is quickly changing due to landfill costs, sustainability requirements and the inherent value in correctly processed fly ash. The main property that makes fly ash suitable for recycling is its use as a pozzolan. Pozzolans exhibit cementitious properties that make them suitable for partial cement replacement, and that can have beneficial properties for concrete mix designs. Fly ash can be used to replace up to a third of the of the Ordinary Portland Cement (OPC) requirement. Suitable fly ash nearly always requires the removal of the less reactive coarser fraction from the finer fraction. Due to the pozzolanic nature of fly ash, it must be processed dry and separation is normally required at 45 micron. In response to the increasing demand from a range of dry classification applications, Metso purchased an established air classification technology suitable for both mining and construction applications. The classifiers intelligent design efficiently utilizes the air flow which keeps power requirements low whilst including a scrubbing/recirculating function within the classifier that allows extremely efficient separations even at very fine sizes. This technology is of global interest to Fly Ash processors, but should be of particular interest in India which is both the second largest cement producer in the world as well as producing 80% of its power from thermal sources. This paper is intended to give a brief overview of fly ash and requirements for use as a pozzolan, air classification of fly ash and a case study from an established and experienced fly ash producer. Keywords: air classifier, fly ash, pozzolan, fineness, cement, cholla, salt river materials group

Sep 1, 2012

By Montaser S. EL Salmawy, Takahide Wakamatsu, Eishi Kusaka

"The effect of ethoxylation of long chain alcohols on the quartz and feldspar flotation behaviors was investigated for surfactants of the octylphenol polyoxyethylene family. The tests were carried out with an average of 7.5 (Triton X 114), 9.5 (Triton X 100), 30 (Triton X305), 40 (Triton X 405) and 70 (TritonX 705) oxyethylene units. Electrokinetic and flotation studies on quartz have shown that at low pH values, quartz could be floated with polyoxyethylene octytlphenols. The possible mode of adsorption of these nonionic surfactants may be suggested to be due to hydrogen bonding between the oxygen of ether and hydrogen in the free hydroxyl groups on quartz surface. It was anticipated that the selectivity between quartz and microcline would decrease as oxyethylenic chain length increases.Electrokinetic methods were used to elucidate the mechanism of surfactants adsorption and to correlate these findings with the optimum flotation conditions. The polymeric surfactants would reduce the negative values of zeta potential of quartz while the reverse is true for feldspar. After treatment of microcline with HCl, its electrokinetic behavior in the presence of Tritons X surfactants became similar to that of quartz.The obtained results would suggest that separation of quartz from feldspar using nonionic surfactants of octylphenoletoxylated alcohols having shorter oxyethylenic chain length at low pH could be achieved"

Jan 1, 2003

By Z. S. Abisheva

Rare and rare earth metals use quite often is an indicator of national economy development. The world structure of the rare-earth metals manufacturing countries in 2015 was presented as follows: China – 94.2%, India – 2.0%, Russia – 1.8%, the USA – 1.2%, Brazil – 0.5%, Malaysia – 0.3%. In Russia, large reserves of rare-earth metals, which reach nearly 28 million tons, are revealed. Kazakhstan, possessing a raw materials source of rare-earth metals, has all prerequisites for development of branch. Rare metals are manufactured in Kazakhstan incidentally by non-ferrous metals production. The production of indium, thallium, cadmium, selenium, tellurium, bismuth is made at the Ust-Kamenogorsk lead plant; tantalum, beryllium, niobium and molybdenum – at the enterprises of “National Atomic Company Kazatomprom” JSC. Production of a titanium, magnesium and vanadium is adjusted on “Ust-Kamenogorsk Titanium-magnesium Plant” JSC. Capacities for beryllic production yield are available on “Ulba Metallurgical Plant” JSC. The main producer of perrhenic production and osmium-187 is "Zhezkazganredmet" RSE. The single producer of gallium in Kazakhstan is “Aluminium of Kazakhstan” JSC; the capacity of enterprise is 25 t a year. In Kazakhstan innovative technologies for rare and rare earths mineral raw materials processing are created. The technology has been developed and a vacuum distillation apparatus has been created to purify crude selenium, which makes it possible to obtain a metal with a main component content of 99.9-99.99%. Technologies for processing of technogenic wastes and byproducts of the copper industry are developed. Implementation of technologies allow to obtain ammonium perrhenate, perrhenic acid, osmium isotope -187, tribasic lead sulphate, silver-concentrate. The technology of complex processing of black shales of Balasauskandyk deposit with the production of gold, vanadium, rare earth elements, uranium and ferrosilicon has been proposed. The processing was carried out using methods of autoclave leaching, sorption, extraction, precipitation. A highly profitable sorption technology for recovery of rhenium from solutions of underground leaching of uranium ores containing 0.2-0.4 mg/L of Re has been created. The organization of ammonium perrhenate production from solutions of uranium ore will significantly increase the volume of its production in Kazakhstan.

Jan 1, 2018

By N. Nehoroshev, P. Solozhenkin, N. Voyloshnikova, A. Pshennikov

"Molecular modeling of clusters of major bismuth minerals, Bi2S3, was carried out whereby molecular models of minerals and reagents clusters were created. Their HOMO and LUMO energy levels were calculated and using known modelling equations, the absolute hardness ?, eV and electronegativity were calculated. The charges of separate atoms of clusters and the change of properties of the minerals were determined which allowed predictions of the flotation properties of raw ores containing rare bismuth minerals. Modeled complexes containing the clusters of minerals and various collectors were constructed, consisting of atoms and bonds within clusters of minerals. Major physical and chemical parameters were determined for the complexes created, including the total and electronic energy. Based on the energy calculations, predictions of the collector efficiency were proposed. The efficiency of collector was established for various thiolic reagents, the compounds of phosphorus (III) and mixtures of reagents. Theoretical results were checked and confirmed against laboratory ore flotation tests. A gold-bismuth-magnetite ore type was studied where gold, bismuth and iron (magnetite) are of industrial interest. The ore contains 2.8 g/t Au, 1.0 g/t Ag, 0.26% Bi, 45% Fe and 1.25% As. Sulphide mineralization can be mainly found in the form of pyrrhotite, pyrite and arsenopyrite. Bismuth can be mainly found in the form of bismuthite and native bismuth. Gold is fine. A flow sheet for Zhelezny Kryazh ore treatment was proposed. This flow sheet consists of grinding to 95-98% -74 µm, sulfide flotation with two cleaner with xanthate addition, cyanidation of flotation concentrate and flotation tailings included treatment with with CaO (6 kg, 6 hours), cyanidation (8 hours) and CIL (8+24 hours). Saleable products are gold doré, bismuth and iron concentrate."

Jan 1, 2014

By W. D. Guo, Y. M. Zhu, B. B. Luo

The main chemical constituents of waste cooking oil are higher fatty acid glycerides, which can be used to produce anionic fatty acids for most non-sulfide flotation. However, using the mixed fatty acids (MFA) produced by waste cooking oil as collectors directly, the flotation effect is usually not satisfactory, especially at lower temperature or room temperature. There are very rare systematic studies about the reason for poor flotation performance of waste cooking oil. This study aims to investigate the flotation and adsorption characteristic of different types of fatty acids in waste cooking oil to find out what kind of fatty acids results in the poor flotation performance. This will provide technical supports and theoretical guidance for the waste cooking oil application in the field of mineral processing. In this study, MFA were produced from the waste cooking oil, and then separated into saturated fatty acids (SFA) as well as unsaturated fatty acids (UFA), which possessing different flotation properties. The properties of the MFA, SFA and UFA were analyzed by iodine value, melting point measurement, Fourier transform infrared (FT-IR) spectroscopy and quartz micro-flotation tests. The results showed that UFA was composed of fatty acids containing group—(CH=CH—CH2)n—, having an iodine value of up to 162.90, a melting point as low as -17.3 ? and stronger low-temperature floatability. In contrast, the SFA was made up with saturated fatty acids and a few oleic acids, with an iodine value of 48.97 and a melting point of 38.8 ?. SFA had shown poor collectability and required a flotation temperature higher than 35 ?. The results of zeta potential measurements, solution chemistry calculation and FT-IR spectra revealed that both UFA and SFA can be adsorbed on the quartz surface activated by CaCl2 via the chemical and hydrogen bonding. The reason MFA having a poor flotation performance is the SFA has an extremely high melting point which affecting the dissolution of the dispersion.

Jan 1, 2018

By Peter Ay, Bodo Müller, Jens Markowski, Manfred Kanthak, Florian Logsch

"Presently the global commodity situation for non ferrous-, precious- and rare metals is characterized by a strong increase in consumption and a simultaneous shortage of materials derived from primary sources. So the use of secondary raw materials gains is important due to economic and ecological reasons. Non Ferrous-, precious- and rare earth metals were detected in household waste (Municipal solid waste, MSW) for years. In MSW-treatments plants NF-metals are actually mostly separated from dried fractions. The separation of these metals is carried out with the aim of removing particles which disrupt further processing. A selective enrichment of individual non-ferrous metals has not been carried out previously. The separated fractions contain mixtures of Al, Cu, Zn, Pb, Sn, alloys, precious metals (e. g. Au, Ag, Pt) and rare metals (Ga, In, Nd etc.) along with considerable amounts of contaminations. The R&D project "NE-Rec" selectively processes the coarsely separated non-ferrous-metal-conglomerates increasing the concentration of targeted metals. Metals and metal mixtures are concentrated by sorting steps and the impurities are discharged from the process. Still contaminated precious metals are then subjected to a wet-chemical treatment. So metals can be specifically brought into solution or can be precipitated to separate unwanted components (inerts, polymers, foreign metals). Further the relevant metals will be concentrated by thermal-metallurgical processes. The technology, developed in the R&D project, enables identification, separation and processing of non-ferrous metals, precious metals and REM in household waste and transfers them into further processable individual fractions."

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

Green pellet strength including drop number and green compression is highly depended on particles size and shape. The used grinding method, ball mill or high pressure grinding roll (HPGR), directly vary the particle size and shape. Considering mode of pellet crack, green pellet is composed of particle-binder-moisture system. Different type of forces existed in such a system to create a stable green pellet: solid particle interaction, magnetic, binding and cohesive forces in the interface of particle-moisture. The pellet failure can occur at solid-liquid interface and/or through liquid phase. Pellet crack occurs when crack passed through entirely the plane failure. In this research, the effect of particle size and shape of pellet feed on green pellet strength has been investigated. It was deduced that green pellet strength highly improved by increase of specific surface area. The drop number and green compression strength of pellets prepared by HPGR was higher than ball mill. It was found that the main reason responsible for this difference was the particle shape. Capillary force is responsible for part of pellet force and improves by decrease of particle size. Also more elongated shape of HPGR particles resulted in higher capillary force due to thinner interface layer between particles. The less circular shape of particles lead to improvement of capillary force as can be occurred for HPGR particles. The rougher shape of HPGR particles resulted in higher wettability of particles and better diffusion of water among particles. In fact the rougher particles means lower connection angle. Aspect ratio of particles was of great importance of crack growth because the required energy of pellet failure increases directly. The required energy for pellet failure increases by increment of particle aspect ratio. The relationship among crack failure force, roughness and aspect ratio has been modeled considering 3 shape descriptors.

Jan 1, 2018

By H. Z. Kuyumcu

Coking of coal blends using high volatile coals with poor coking abilities to produce a high quality coke for blast furnace application can be achieved by compacting the coal blend prior to the carbonization process. Here densification up to a relative material density of 80 %, i.e. a compact density around 1100 kg/m3, has proven to be advantageous. Coal is compacted by stamping, if the so-called stamp charging process applied. Compacting of the coal by pressing is practised in case of the cokemaking with so-called heat-recovery ovens. Stamped and pressed coal cakes require over the cake volume uniform high density and mechanical stability. Besides the aspects of the coal selection, the efficiency of the process is mainly determined by the operating parameters compacting time and compacting energy for coal cake making. At the Department for Mechanical Process Engineering & Solids Processing of the Technical University Berlin the two sub-processes of densification and strengthening during stamping and during pressing are theoretically and experimentally investigated using specially developed lab-scale compacting test units and a strength test device. Describing cake density in terms of coal properties for a given coal and measured compacting energy input then leads to a compacting equation with the so-called Stampability as the integral model parameter for the stamping process. For the pressing process the cake density can be calculated with the measured compacting pressure and the Compressibility factor, respectively. Investigations were carried out to provide evidence of a significant influence of coal type, coal surface moisture, coal granulometric and mechanical properties on the densification process. The overall objective of the work is to establish a comprehensive mathematical model on the compacting behavior of large coal bulk quantities and the optimization of the compacting processes by stamping and by pressing. Keywords: coal compacting, agglomeration, stamping, pressing, cokemaking

Sep 1, 2012

By C. A. Acuña

Extensive literature exists on the motion of single bubbles and the behaviour of swarms of bubbles. This contribution describes work to track and reveal the motion of individual bubbles in a swarm. The technique is based on high speed cinematography and tracking of multiple moving objects. Image processing algorithms were implemented in Matlab to isolate and measure geometric proper-ties of the bubbles in image sequences recorded at 2 ms interval; and these properties were compiled into a data structure. To track a bubble, the geometric properties and a matching criterion were applied on consecutive pictures to identify the bubble. The bubble trajectory was reconstructed from the data structure for the matched objects. The methodology is briefly described. The new technique was tested for bubbles produced at slot-type spargers (i.e., approximately 2-D swarms) in the presence of two frother types ('strong' and 'weak'). Two observations are discussed: a) that bubble motion in a swarm describes a velocity-size relationship dictated by the dominant bubble size class; and b) that surfactant type influences bubble rise velocity for bubbles in the range 0.1 mm to 4 mm. The latter suggests surface viscosity rather than surface immobilization determines bubble rise velocity.

Jan 1, 2014

By Junwei Han, Wenhua Li, Wenqing Qin, Fen Jiao, Wei Liu, Jiaqi Xu

"A novel technology was developed to study the process of recycling copper from waste printed circuit boards (WPCBs), which are the main source of metal production in the next decades. The chemical compositions of the WPCBs were investigated. The results indicated that the PCB powder was mainly composed of copper (38.5 wt.%), iron, aluminum, and non-metallic materials. Copper is mainly in the form of Cu and is the most valuable metal for the recycle of WPCBs. The concentrated WPCBs powder, obtained by the mechanical process, were pressed as the anode, which was directly electrolyzed to produce copper. The effects of H2SO4 concentration, Cu2+ concentration, current density, pole pitch, and liquid-to-solid ratio on the voltage, current efficiency, and copper extraction were investigated. The results indicated that the optimum conditions were liquid-to-solid ratio of 30 mL/g, current density of 571 A/m2, sulfuric acid concentration of 180 g/L, 50 g/L of copper ion, polar distance of 3 cm. Under the conditions, a desired current efficiency could be achieved. Meanwhile, about 95.62% Cu was recovered from the WPCBs. The experimental studies also revealed that the purity of copper obtained at the highest current efficiency was higher to 99.98%. Produced copper sheet were characterized by X-ray diffraction (XRD). XRD analysis indicated that the copper was the main phase. INTRODUCTION With the rapid development of electronic industry, more and more waste electronic and electrical equipments (WEEE) are generated every year (Fogarasi et al., 2012; Liang et al., 2013). The production of printed circuit boards (PCBs) is the base of electronic industry, because it is the essential part of all electrical and electronic equipments (Schlummer et al., 2007). As a result, a considerable amount of waste PCBs containing plenty of heavy metals have to be treated. In general, PCBs contain about 28% metals that are abundant non-ferrous metals such as Cu, Pb, and Sn. Printed circuit boards can be considered as a secondary resource for recycling rather than wasting. The contents of gold and silver respectively reach 80 g/t and 3300 g/t, which are much higher than that of primary ores. Copper is the main metal of PCB and its content is as high as 26.8% ( Zhang et al., 2009)."

Jan 1, 2018

By Venkataramana Runkana, Aditya Pareek, Vishnu Masampally, Nagaravi Kumar Varma Nadimpalli

"Recovery and grade of the ore produced are two important metrics, which define the profitability of a mineral processing plant. Achieving high grade and high recovery at the same time in a mineral processing plant is difficult due to conflicting nature of the two objectives. To explore the operability limits of the plant operations and find the set of operating conditions that can help achieve the best possible recovery and grade, there is a need to solve a multi-objective optimization (MOO) problem. Past research focused on building a plant-wide simulation model or on optimization of individual units or a part of a mineral processing plant like grinding circuit, crushing circuit, etc. However, it is necessary to consider optimization of the complete plant in order to optimize the plant performance. Here, we have formulated the mineral processing plant performance optimization as a MOO problem. We have applied machine-learning algorithms such as random forest to build models to predict the recovery and grade of the ore. A non-dominated sorting-based multi-objective evolutionary algorithm called NSGA-II (Non-dominated Sorting Genetic Algorithm II) was employed to solve the MOO problem. Since the number of parameters that influence recovery and grade are quite large, we have applied machine-learning algorithms for feature selection or identification of key process variables. Pareto optimal conditions were determined for manipulated variables like grinding mill throughput, speed ratio at SAG mill, speed of centrifugal pump, water addition at different locations etc. The results obtained are useful in identifying the operability of a mineral processing plant to achieve the optimum grade and recovery for a given feed grade and the processing circuit. INTRODUCTION Copper is majorly mined or extracted as copper sulfides from large open pit mines in porphyry copper deposits. Among all the available ores, sulfides are the most commercial ores, especially chalcopyrite (Greenwood and Alan, 1997). Copper grade in these ores generally lies between 0.4 to 1.0%. In order to perform smelting operation, the grade of copper has to be improved to around 30% (Biswas et al. 2013). This targeted copper grade is achieved through two stages of mineral processing. Firstly, the copper in the ore has to be liberated by crushing the mineral rock. Secondly, the liberated copper in the crushed ore is then physically separated from other minerals like nickel by froth flotation techniques."

Jan 1, 2018

By V. G. Minenko, V. A. Chanturiya, A. L. Samusev

Eudialyte is one of perspective resources of zirconium and other rare earth elements (REEs). Large reserves of eudialyte concentrated in the Murmansk region of the Russian Federation. Usually, technologies of REE treatment include the decomposition of eudialyte concentrate in different acidic, extraction and utilization of all components. The main problems in the leaching of eudialyte include are: the formation of an unfiltered silicon-containing gel; low recovery of REE; difficulty extraction of metals from the productive solution; high aggressiveness of the reagents. One of the promising trends of intensification of the processing of hard-to-degrease rare metal raw materials is the use of energy methods for affecting mineral suspensions. These methods make it possible to increase the efficiency of break up fine-dispersed mineral complexes and extracting micro- and nanoparticles of a valuable component in subsequent deep processing. The purpose of this work is to investigate the effect of energy impacts on the nitric acid leaching of eudialyte concentrate. Experimental studies were carried out in a developed laboratory facility that makes it possible to evaluate the effect of electrochemical, ultrasonic and combined effects on the leaching of zirconium and REE from eudialyte concentrate. The studies carried out on the samples of eudialyte concentrate with the size class of -0.315 + 0.063 mm showed that the use of electrochemical and acoustic effects increases the extraction of ZrO2 in the production solution in 1.6 - 2.5 times, REE in 1.3 - 2.2 times, respectively. An analysis of the microstructure and phase composition of the surface of the eudialyte concentrate showed that the intensification of the leaching process is due to surface cleaning from the silicon-containing gel, as well as the opening of capillary channels and microcracks, which accelerates mass-transfer processes. The results obtained open wide opportunities for creation of modern and effective technology of processing of eudialyte concentrate, producing high-quality zirconium products and REE.

Jan 1, 2018

By U. M. J. Boin, W. L. Dalmijn, T. P. R. de Jong

"This paper explores the complex interrelationship between the resource cycle, recycling and metal production as a function of economics, environmental legislation, and product design. It is argued that central to optimising this resource cycle lies the control in particular of physical separation plants by the application of advanced sensor technology and sorting equipment, as well as suitable control and sampling algorithms supported by optimising mass balance models.Metals are produced through a long chain of processes. For primary resources, metals production goes through mining, mineral processing, ore smelting, conversion and refining steps or via low temperature hydrometallurgical processes, or a combination of both pyro- and hydrometallurgical operations. For the recycling of resources, metals are separated and recovered from metal scrap, which plays an increasingly important role in the world. Metals after being produced, either from primary or recycling resources, have to be further refined or manufactured into various types of alloys and finally shaped into different products for the end-users. Since the end-user discards products the contained materials find their way back into the resource cycle as scrap. Therefore, controlling the metallurgical reactors also controls, in a much broader sense, the material quality in the complete metals cycle, from the production phase, to the end-use phase, up to the recycling phase (Reuter et al., 2003). The recycling phase includes separation of materials into saleable intermediate products, which are reintroduced into the production phase as a recycling resource. Therefore, the metallurgical processes in each unit operation in the metals production and processing chain have to be controlled, so as to achieve optimal performance of high product quality, low energy and materials consumption, and low environmental impact."

Jan 1, 2003

By Axel Pankewitz, Andrew Smith, Mathias Stender, Christian Behrens

"Particle size measurement is one of the most important factors in obtaining peak performance of the mineral processing plant in order to ensure efficient milling and flotation circuit operation. Off-line particle distribution analysis technologies only allow an infrequent check of the ore slurry size and hence do not allow for timely process monitoring or intervention. Most existing on-line particle size analysers suffer from a variety of disabilities such as poor statistics, non-representative sampling or mechanically complex setup. This paper will describe an Ultrasonic Extinction based method which overcomes many limitations of existing online analysers and has proven its performance for mineral applications over many years. Installation examples will be given. Since new technologies usually raise e questions about comparability and agreement to common particle size analytical methods e.g. sieving or laser diffraction analysis, extensive studies were performed comparing these different technologies to quantify the quality of results as well as its mathematical robustness."

Jan 1, 2014

By I. I. Beloglazov, G. A. Iusupov, A. Ju. Feoktistov

"The aim of this paper is to study the numerical modeling of the crushing process in a jaw crusher with complex motion jaws using Discrete Element Method (DEM). The main goals are to ensure the conformity of numerical simulation results to the experimental data, optimize the operating modes and the crusher design and develop automated verification and calibration methodology. It is offered to use automated selection of mathematical model parameters using large- or laboratory-scale experiments instead of deriving parameters from conventional intensive material tests (e.g. drop-weight test). Experimental data were obtained from a large-scale crusher designed and manufactured by the company “Mekhanobr-Tekhnika”. Both jaws have their drive shafts located asymmetrically; one jaw is driven in the upper part, the second at the base. The crushing process involves fragmentation of single smoothed rectangular granite particles of the same weight. During the experiment, the required parameters such as particle size distribution were obtained for further computer simulations. Based on the obtained experimental data, the Rocky DEM model was built. Simulation breakage parameters were calibrated using automated parameter selection methodology based on multiple set of parameter-controlled simulations. A good correlation of the experimental data and numerical simulation data was obtained. The methodology in combination with well-known capabilities of simulation modeling will help reduce the research time in the development of new mineral processing equipment.INTRODUCTION Preparation of rock mass for enrichment includes the power-consuming processes of crushing and grinding. Initial rock mass crushing is performed by means of drilling and blasting operations. To reduce the average size of a rock piece, primary crushers, mostly jaw crushers, are further applied. The advantages of the jaw crusher are simple design, easy maintenance and repair. One of the drawbacks is large oscillating masses and, thus, high power consumption during operation (55 - 200 kW). Jaw crushing simulation will help optimize the crushing process and improve further rock transportation and processing performance."

Jan 1, 2018