Search Documents

By Tiziana Apuani

The study refers to an area of about 70 km2, extended in the Italian Central Alps along the the San Giacomo Valley where different civil and mining works are present The regional geological setting is related to the Pennidic Nappe arrangement, characterized by the emplacement of sub-horizontal gneissic bodies resulting from the Mesoalpine isoclinalic folding of crystalline basements, emplaced throw East, and separated by matasedimentary cover units. The investigated geological rocks, belong to the ?Tambò?Unit, overlapped by its meta-sedimentary cover and by the ?Suretta? Unit. The tectonic contact gently dips to the E?NE. The valley, furrowed by the Liro Torrent, follows a N?S striking tectonic lineament, almost parallel to the nappe contact. A number of more then 70 sites, distributed in the studied area, were chosen and detailed structural and geomechanical field surveys were performed to characterize the rock masses, its intact rock and discontinuities. The procedure identifies the number of joint sets, their representative orientation, the set spacing, the type of movement, the amount of dilatation, the degree of alteration, the roughness coefficient, the presence and nature of infill. Rock mass quality indexes, such as the Rock Mass Rating (Bieniawski, 1989) or the Geological Strength Index (Hoek et al. 2002) have been evaluated in each surveyed site. The work is a contribute in assessing how the geometrical and geomechanical properties of the rock masses can be regarded as regionalized variables. The spatial distribution of these properties is a function of the geological and structural phenomena at which the rock masses have been subjected. The presented geostatistical analysis regards the spatial variation of the orientation of the most representative joint set.

May 1, 2009

"The measurement of error in assays collected as part of a mineral exploration program or mining operation historically has been undertaken in a variety of ways. Different parameters have been used to describe the magnitude of relative error, and each of these parameters is related to the standard measure of relative error, the coefficient of variation. Calculation of the coefficient of variation can be undertaken in a variety of ways; however, only one produces unbiased estimates of measurement error: the root mean square coefficient of variation calculated from the individual coefficients of variation.Thompson and Howarth’s error analysis approach has also been used to describe measurement error. However, because this approach utilizes a regression line to describe error, it provides a substantially different measure of error than the root mean square coefficient of variation. Furthermore, because regression is used, Thompson and Howarth’s results should only be used for estimating error in individual samples, and not for describing the average error in a data set. As a result, Thompson and Howarth’s results should not be used to determine the magnitudes of component errors introduced during geochemical sampling, preparation, and analysis.Finally, the standard error on the coefficient of variation is derived, and it is shown that very poor estimates of relative error are obtained from duplicate data. As a result, geoscientists seeking to determine the average relative error in a data set should use a very large number of duplicate samples to make this estimate, particularly if the average relative error is large."

Jan 1, 2007

By J. R. Goode

"The Las Cristinas deposit in Venezuela contains reserves of 12.8 million ounces of gold at a grade of 1.20 g/t (Crystallex, 2004). The deposit comprises fully oxidized saprolite (SAPO) overlying a layer of sulphide-enriched saprolite (SAPS) which lies above carbonateleached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same concentration in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper which has been leached and deposited in the SAPS zone.A previous owner began investigation of the Las Cristinas deposit in 1991. Over the next seven years, the company drilled 1,174 holes with a total length of 159 km, conducted extensive metallurgical testwork, including pilot plant operations, and completed feasibility studies. Construction was started in 1997 and again in 1999, however, on each occasion was suspended.Crystallex has been producing gold inVenezuela since the early 1990s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana (CVG) to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in late 2002 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-inleach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot-scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the testwork conducted in 2003, discusses a 20,000 t/d plant design, and presents economic data."

Jan 1, 2005

By W. J. Young, K. B. Macneill, C. N. Smith

"A BRIEF HISTORY OF THE MURRAY BROOK MINERAL DEPOSITDuring the mid-1950's intensive exploration activity in northern New Brunswick followed the discovery of the world class Brunswick base metal deposit. Using the prototypes of modern airborne geophysical and geochemical exploration techniques many mineralized areas in the Bathurst-Newcastle area were quickly identified. This base metal - silver camp is situated within the metavolcanic - metasidementary rocks of the Tetagouche Group which forms a roughly circular caldera-chaped voloanio complex of Ordivician age.One of the early results in the exploration history in the camp was the discovery of the Murray Brook Deposit by Kennco Explorations, (Canada) Limited. During routine ground checking of geophysical anomalies, most of which turned out to be graphitic schist, the discovery of some copper bearing float was made by the exploration team. This encouraged the company sufficiently to carry out a regional stream sampling program which lead to a large anomaly associated with a hematitic gossan. Diamond drilling of a weak Slingram anomaly over the gossan zone resulted in the discovery of massive sulphide lenses. This was followed in 1956-7 with an intensive drilling program. The result was the delineation of a potential ore body containing an estimated 23 million tons with an overall grade of 0.44% copper, 0.86% lead, 1.95% zinc, 25.73 g/tonne (0.91 oz/ton) silver, 0.28 g/tonne (0.01 oz/ton) gold. Within this package were higher grade zones of copper and lead-zinc mineralization approaching ore grades.A thick blanket of gossan was present and is reported to have caused the drillers considerable trouble as they attempted to penetrate it to get to the underlying sulphides. The gossan, consisting of iron oxides and silica fragments sits on top of the massive sulphides and attains a remarkable thickness of 45.5 meters (150'). Early work had suggested that the gossan was enriched in gold and silver. If this were the case and if the precious metal could be leached out with cyanide, then mining and recovering those values might be economic.With this in mind Northumberland Mines Limited optioned the property from Kennco in 1985. Preliminary leach tests indicated that indeed the gold in particular leached readily. Subsequent drilling of the gossan (using triple core barrel technology for better recovery of the easily ground core) indicated 1,536,363 tonnes (1,690,000 tons) with an average grade of 1.05 g/tonne (0.037 oz/ton) gold and 42.13 g/tonne"

Jan 1, 1993

By Juergen Antrekowitsch, Stefan Steinlechner

"Within the last decades, mainly the base metals, like zinc, copper and lead were recycled from different industrial residues without taking into account that accompanied minor side-elements are often also present. A high supply risk for critical raw materials derives mainly due to the high share of the worldwide production in a limited number of countries. Examples include indium and germanium in China, PGM in South Africa and Russia or cobalt and tungsten in the Democratic Republic of Congo. By taking the market of critical metals into account, the recycling of potential residues does not only contribute to an economic treatment but also to the European strategy to decrease the supply risk of certain metals. Depending on the metal discussed, political unrest, decreasing primary resources leading to supply risks in different countries or also simply economic interests moved these mentioned side elements and with this the residues where they are present in, into the focus of the recycling industry.Because of this, the typical routes of lead, zinc and copper production are evaluated concerning generated residues and their typical contents of contained minor elements. Finally, the paper tries to answer the questions how a possible treatment of these wastes could contribute to the overall supply of for example silver but also other minor elements."

Jan 1, 2016

By Emilio Giuseppe Sarno Severi

Mining and Petroleum Similar Industries ?Asset Intensive ?Exposed to market volatility ?Highly Risky Operations ?Scarcity of Experienced and Trained resources ?Operating in diverse countries with different cultures ?Increasing Environmental and Safety Regulations

Nov 1, 2011

By D. L. Putnam

Snap Lake Mine ?? Complex dyke ore body ?? Underground operation ?? 1.1 million tonnes per annum ?? 1.2 carats per tonne ?? On-site diesel power generation ?? Supply by ice road and air ?? Milestones ? Construction commenced in 2005 ? Commissioning 2007 ? First diamonds August 2007

May 1, 2008

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008

By R. J. MacLeod

"INTRODUCTIONThe removal of water or liquid from slurries and solutions is a procedure generally present in many process industries. This has prompted the development of many mechanical and thermal devices with which, I have no doubt you are al1 familiar.In the mining industry, beneficiation of ores necessitates ' the removal of water or other 1iquid from the concentrate material. The most common method of accomplishing this is by means of thickeners, vacuum filters and rotary dryers, generally all three and in that order;The use of spray drying techniques to obtain the same end has many advantages and these will be outlined here.THE PRINCIPLE OF SPRAY DRYINGA Spray Dryer consists of a cyclone shaped chamber where hot air and atomized concentrate are introduced in the upper section. (Sec figure No. 1). Efficient mixing of these two streams produce dry concentrate and moist spent air, both of which are removed from the base of the chamber.Thermal dewatering involves the product ion of heat and spray drying has no special requirements in this area. Generally a direct fired air heater is used and the products of combustion whether they stem from the use of gas, oil or coal fuel go into the spray dryer along with quench or dilution air which is used to reduce the combustion gases to the desired temperature. This generally lies in the range of 1,000 to 1,600° F. In spite of these relatively high inlet temperatures, the spray drying process eliminates the need for refractory lining or indeed any special heat resistant metals except on the air inlet ducting. Waste heat may also be used even if a significant amount of contamination is present."

Jan 1, 1972

By Turgut Yalcin

"High-grade concentrates are achieved in flotation columns primarily due to the use of thick froth layers and wash water, both of which facilitate the drainage of hydrophilic minerals from the froth. However, conventional columns employ tall, non-agitated recovery sections for bubble-particle attachment that require high headroom and special gas spargers as well as imposing particle size limitations. These disadvantages can be all alleviated by carrying out the recovery part of the process in a mechanical or pneumatic cell which generate froth more conveniently and efficiently.This paper describes the combining of mechanical and column flotation in a single unit and discusses the influence of various parameters on the performance of the system.INTRODUCTIONIn a flotation process, some of the minerals lifted up to the froth phase may drain back to the pulp due to various reasons such as weak attachment of particles to air bubbles, bursting of air bubbles, agitation of froth, etc. Weakly floating and entrained hydrophilic minerals drain at a faster rate than the strongly floating minerals, and effective exploitation of such differential drainage can lead to cleaner concentrates.For a given mineral, if the rate of flotation from pulp to froth is k1 (min·1) and the rate of drainage from froth to pulp is k2 (min""1), then the net (overall) flotation rate of the mineral, k (min-1 ), will be [Lynch et al., 1981 ]:"

Jan 1, 1997

By C. H. Bertoni, A. Vachon

The Corner bay copper deposit is the first significan discovery on the south limb of the Dore Lake Complex, located at the eastern end of the Detour Lake-Chibougamau greenstone belt, Quebec. The deposit was discovered in March, 1981, after 26 years of intermittent work in the area. Mineralization is found in a shear zone cut ting rocks ranging in composition, from gabbroic anorthosites to anorthositic gabbros which have been intensely altered and deformed by at least two tectonometamorphic events. Both the copper-bearing shear zone and its host rocks are cut by a large NE-striking gabbro dyke. Most of the known mineralization is found east of the dyke, but two deep exploration holes have shown that the down dip extension is present to the west of the dyke. The mineralized shear varies from one to 15 metres in width, strikes around 010° and dips from 70° to 80° to the west, and has been tested for a length of 700 metres. The wall rocks are usually chloritized and silicified. Mineralization is characterized by chalcopyrite, pyrite, molybdenite, magnetite, and sphalerite occurring mainly as the matrix to quartz-carbonate breccias in the "main" shear zone. The predominant sulphides are pyrite and chalcopyri te as crystals or fragments. The brecciated mineralized shear shows evidence that there was at least one remobilization of the shear and it is suggested that copper-bearing fluids invaded the shear during its remobilization. The exact timing and source of mineralization are not known. Up to February 1984, 38 holes had been drilled to outline indicated reserves to a depth of 450 m of 1,5 million tonnes grading approximately 4% copper, 0.34 gm, gold and 13.71 gm silver per tonne. It is believed that there is considerable reserve potential in the block west of the gab bro dyke, the down dip extension of the main zone.

Jan 1, 1984

By T. Peters, W. C. Ferguson

"Shebandowan is about 600 miles west of Sudbury and 50 miles west of Thunderbay close to the trans Canada highway. Shebandowan Lake is about 38 miles long. The ore body is located between No. 1 and No. 2 shafts at the lower end of the lake. The economic mineralization lies between 200 and 2000 feet below. Years ago development of this ore body would probably have entailed draining the lake and using the open pit method to mine the ore.The water of Gold Creek which flows into Lake Shebandowan is representative of all local waters and is very close to rain water in purity. It is obvious that any industrial water discharged would have a measurable impact on the local water. The dissolved solids content is low and consistent with what is normally found in northern Ontario.A Koepe headframe is the only visible evidence of the mine from the lake. The Koepe headframe is esthetically pleasing and quiet in operation. The structure is of concrete to control noise. Noise from ore dumping is controlled by dumping underground to an ore pocket 400 feet below the surface. A 3600 foot conveyor belt carries the ore underground to the mill and is out of sight of the lake and the cottagers. The main objective to all our environmental efforts has been to preserve the natural beauty of the region. The mill is housed in a conventional metal-clad-siding building painted in esthetically pleasing colours. A single service building houses warehouse, dry storage and offices. The area surrounding the mill and service building is paved or grassed and drainage from this area is collected and pumped to the tailings area. Air intake silencers are installed on the compressors which are mounted at the back of the mill. Sound measurements taken on the lake indicate that noise suppression is excellent."

Jan 1, 1975

By K. Honkivaara, S. Junnikkala, J. Aho, K. Föhr, P. Lampinen

"Bubble area flux has been claimed to be a major tool to dimension flotation equipment. The paper describes laboratory scale (batch and 301 continuous cell using plant feed) and small-scale (1 ,8m3) industrial experiments with coarse-grained massive sulphide ore.Samples were taken with different froth thickness and air addition rates while the bubble size was measured with an UTC capillary device. Problems of averaging the bubble size measurements and the bubble area flux measurements are also discussed.Material balances were calculated using the commercial program BILCO. The flotation rate constants were calculated for pulp and for froth assuming that we can extrapolate the flotation rate constant of the pulp phase from tests using very thin froth thicknesses.The results indicate that the bubble area flux is not alone an adequate dimensioning tool. With fine sizes there was a nearly linear relationship between the bubble area flux and rate constant for constant impeller revolutions. For coarse sizes the form of the relationship is non-linear and seems to go through a maximum value. Thus the final flotation outcome is not a simple function of bubble area flux but depends on the particle size distribution and other more traditional flotation cell dimensioning variables. The effect of the froth residence time in the total recovery of coarse particles is large, but will not be treated in this paper."

Jan 1, 2000

By M. Doggett

All 231 Canadian primary gold mines that produced from 1946 to 2004 were analyzed with respect to their production and economic characteristics. Trend analysis revealed that the average annual capacity of Canadian gold mines, as measured by ore processed or gold produced, has increased over time. Conversely, the average grade of gold mines has decreased over time. The distribution of gold output is highly uneven: for example, the 22 giant mines producing more than 100 t (metric tonnes) of gold account for 62% of total output. Small mines producing less than 10 t Au account for 54% of total mines, but less than 4% of total gold. Each historical mine in the database was evaluated on the basis of a set of economic and technical assumptions to determine if it would be economic to develop today. Based on the net present value using an 8% discount rate, only 103 of the 231 mines were determined to be economic. About 80% of the uneconomic mines had less than 10 t of contained gold, and 63% had less than 5 t. It is concluded that these small mines would not be viable today due to a combination of real capital cost increases, and more stringent permitting and environmental regulations. The implication is that future gold supply in Canada will hinge on the discovery and development of a new generation of larger mines. Given that only one giant mine has been discovered in the past 20 years, it seems likely that gold output will decrease in the future.

Jan 1, 2007

By S. Bellec, P. Champagne, J. Châteauneuf, A. Berton, S. Fortier

"The start-up of new plants, extending from the commissioning of equipment to the production ramp-up, is a critical period where the processing circuit operation must be done in a structured and well controlled way to enable the gradual, safe and rapid achievement of production targets. The magnitude of the many risks associated with this pivotal period is accentuated in the actual context of low commodity prices. However, the implementation of a method that analyzes risks associated with a start-up, their probability of occurrence and their impacts leads to the identification of a series of preventive actions that can be applied in order to reduce potential negative impacts.Soutex has been involved in numerous start-ups over the last few years and has developed a structured methodology to assess this crucial period, maximize the pre-start-up preparation, ensure a smoother and safer ramp-up period and minimize the time needed before reaching commercial production.This paper describes a method to identify preventive actions to apply in order to reduce risks related to a plant start-up. Then, the various steps of the method are demonstrated using the industrial case study of the Canadian Malartic gold plant situated in Abitibi, Québec. The specific preventive actions, during start-up, the organisational measures and the ramp-up plan are detailed as they were effectively achieved. Finally, the post start-up actions are presented as well as some key results illustrating the achievement of their prior defined objectives.IntroductionPlanning a new plant or new circuit start-up in a mine installation involves various risks, both at the economical and safety levels. Unprepared staff and equipment can lead to safety issues that could threaten plant staff as well as the environment. Moreover, a poorly prepared start-up could often lead to equipment break-down, production stoppages and delays, leading to important economic impacts, delaying commercial production and therefore affecting directly the profitability of mining projects.It is common in the industry to have structured commissioning procedures for major equipment taken separately. Technical personnel from the equipment manufacturing company would usually come on site in order to perform the pre-operation verification, dry runs and the first hours of operations. This kind of assistance is usually focussed on one piece of equipment and neglects the interactions between the various equipment of the production chain. The commissioning phase is usually maintenance oriented and the information given by the manufacturing representative seldomly flows through the operation staff (in the case of this paper, the denomination “staff” refers to both managing and operating employees). The global process is usually not taken into consideration by the technical personnel sent on-site by the manufacturer during the commissioning phase. Many papers can be found describing the commissioning of new equipment focussing on the technology (Côté and Adante (2009), Wells et al (2007)) but without dealing with its integration process in the complete production chain."

Jan 1, 2016

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By Nick Poushinsky

OVERVIEW OF PRESENTATION ?Stantec?s Northern Presence ?Challenges for Northern Development ?Environmental Approval Challenges ?History/Expectations ?Baseline Data ?Consultation ?Regulatory Processes ?Extra ?Regulatory ?Keys to Success

May 1, 2009

By J. E. Nesset

"I had been requested earlier this year by MetSoc, our sister society of CIM, to contribute a chapter on technical developments in Canadian mineral processing over the past 50 years to their 50th Anniversary volume. Accepting the challenge of assembling such a chapter seemed at first a reasonably straightforward task, until one realises that the list of contributions by Canadians to mineral processing over this period has been more than just significant. It turns out to have been an extraordinarily fertile time for innovation and impact for Canadian-based technology. The list is necessarily a subjective one, however I had no trouble identifying twenty technology developments that are clearly outstanding, and there are undoubtedly others. As much as possible, I approached the individuals themselves who played key roles in each technology and asked that they tell the “story”. Without exception, all who were invited accepted eagerly and delivered more than I had hoped for. The technologies have been grouped into those that are truly Canadian innovations, such as the Knelson gravity concentrator and the McGill gas dispersion sensors in flotation, and technologies where Canadians and Canada played a very significant role in their success and implementation, such as AG/SAG grinding and ion-beam surface analysis. Also included are what may be termed technology transfer initiatives and institutions that have risen to a world class level, such as SGS Lakefield and the Canadian Mineral Processors Society of CIM. The challenge is now for the coming generation to continue this record of innovation and contribution to the industry, and that includes the (mostly) Canadian mining and metallurgical companies who have taken the longer term view and supported many of these initiatives, through their critical early years, with both financing and project sites for these ideas. Let us hope that the current trend of mining company globalization will not dampen their enthusiasm to participate. This plenary presentation will highlight many of these technologies, the individuals behind them, and their significance to the mineral processing industry."

Jan 1, 2012

By J-L. Tang

A new rhcoforming processing of Al alloys with component shaping systems apart from slurry preparation systems is experimentally exploited, using the reversible multilevel-speed electromagnetic stirrer, the slurry transfer tool and its coating, the thin plate sample with five steps and rheocasting mould, all of which are independently developed. The results show that semi-solid A356 alloy slurry with shape factor of about 0.85 and particle size of 70~80 µm (under air-cooling condition) could be prepared in 20~25 s, fully meeting the production rate of high pressure die casting. The slurry could be smoothly transferred from the slurry preparation equipment to the rheocasting shot chamber while the slurry temperature of slurry decreases by no more than 3 . The tensile strength and elongation of the semi-solid rheocasting samples could be respectively increased by 11.6~18.2 % and 42.5~50 % compared with the traditional liquid die casting ones, and the rheoforming processing has close affinity with the traditional hot working processes.

Jan 1, 2007

By Virginia T. McLemore

The Gallinas Mountains are in northern Lincoln County and southern Torrance County, New Mexico, USA where a series of alkaline igneous bodies, including porphyritic latite, trachyte/syenite, andesite, and rhyolite laccoliths, flows, dikes, and plugs, have intruded Permian sedimentary rocks belonging to the Permian Abo, Yeso, and Glorieta Formations. A small amount of bastnaesite, a REE mineral, was recovered during processing for fluorite from the Gallinas Mountains. Four types of deposits are found in the Gallinas Mountains: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipes and iron skarn deposits; all are associated with Tertiary alkaline to alkalic-calcic igneous rocks. Alteration includes brecciation, silicification, chloritization, and fenitization. District zonation is defined by Cu-REE-F (±Pb, Zn, Ag) veins that form center of the district, surrounded by REE-F veins. Carbonatites are inferred at depth by the presence of fenitization, carbonatization of the breccias, presence of REE and similarity of the intrusive rocks and mineralization to areas with known carbonatites.

May 1, 2011