Search Documents

By S. A. L. Read

"The intact rock constant, mi, is one of the three basic input parameters required for the widelyused Hoek-Brown failure criterion. Values for the constant should ideally be determined by statistical analysis of laboratory test data. In this paper the influence of the inclusion or exclusion of tensile test data on derived values is discussed. We firstly investigate the relationship between direct tensile strength (DTS) test values and Brazilian tensile strength (BTS) test values based on a literature search, finding that the correlation between the two test types is DTS = 0.9*BTS, independent of the lithology being tested. Secondly, using the shear strength database of Douglas (2002), we examine the influence of confining pressure range and the inclusion or exclusion of DTS and BTS test values on calculated values of mi.Chief amongst the influences was the exclusion of tensile data in the calculation procedure, particularly when the Hoek triaxial confining stress range requirement (?3?max = 0.5?c) was not satisfied. Based on a reasonable 1:1 relationship between R (the ratio of unconfined compressive to tensile strength), use of actual tensile data in the calculations for the Hoek brown failure criterion is considered to be a simpler and more robust approach to the use of a tensile cutoff based on empirical criteria such as that of Fairhurst (1964). We advocate the fitting a failure curve using compressive and tensile test data as the most reliable means of calculating mi, while at the same time satisfying requirements as originally advocated by Hoek relating to the appropriate triaxial confining stress range (?3?max = 0.5?c) and sufficient (>5) evenlyspread data points. In the absence of triaxial data the use of R provides a practical means of obtaining estimates of mi that are more robust than guideline values."

Jan 1, 2015

By A. Vien, B. C. Flintoff, R. P. Edwards

"A major thrust in industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements in control performance can be achieved by getting back to the basics.IntroductionEvery modem concentrator has a state-of-the-art computer control system in place. Several of these are contemplating installing, or have installed, advanced control systems, such as expert systems, but the foundation of their control system remains the PI controller. Although the authors are not aware of any survey or published information for the mineral processing industry, it is reasonable to assume that it would be similar to the pulp and paper industry. ""The average [pulp] mill has some 2000 control loops of which 97% use PI control. This means that PID, dead time compensation, adaptive controllers, specialized algorithms, ... , constitute only 3% of the installed base."" (Bialkowski [1992]).Bialkowski [1992] also stated that ""If you have been keeping score, only 20% of the loops surveyed actually decrease variability in automatic over manual mode of operation, in the short term."" He attributed the problems to: poor tuning (30% of all loops), control valve problems (30% of all loops) and process problems (20% of all loops). There appear to be a serious need to go back to basics and review the existing control system."

Jan 1, 1998

By H. M. Lewis

The current status of the international zinc market is summarized, and a supply /demand outlook is presented for the next five years. A number of technical problems facing the industry are outlined. Introduction ZINC has sometimes been called the unknown metal. Considering that on a world basis it ranks third among non-ferrous metals in production and consumption, zinc retains a certain modesty. It has no distinctive colour like copper, lacks the low density of aluminum or magnesium and is not always easy to identify as a product. The 'spangle' of galvanized steel is probably zinc's most distinguishing feature. The purpose of this article is to develop an over-all review of zinc. Starting with the current position of the metal, the major factors that will shape its future will be described so that an assessment of the outlook for zinc can be made.

Jan 1, 1978

By Jack Zhang, Yunguo Tang, Baodong Zhao

"Rare earth elements (REEs) have numerous key applications in both traditional and advanced technologies. A shortage of some critical REEs is expected due to the discrepancy between the REE abundance in REE deposits and the REE demand from the market. For example, Neodymium, Europium, Terbium, Dysprosium, Erbium and Yttrium are expected to be in short supply. REE recovery and separation from secondary resources such as uranium wastes, heavy mineral sands, and recycled materials can balance the shortfall in a cost effective way.The Saskatchewan Research Council (SRC) is engaged in the development and commercialization of complete REE recovery and separation technologies in Canada. One of SRC’s newest developments is the design and commissioning of a heavy rare earth (HREE) separation pilot plant. The pilot plant uses hundreds of stages of solvent extraction (SX) to produce high purity individual HREEs from both primary and secondary resources.This paper presents the design of an HREE recovery process for the particular case of uranium processing wastes. The separation results of a group separation are reported and discussed, as well as the issues and the challenges of the development, commissioning and operation of the continuous SX pilot plant.IntroductionSignificant amounts of strategic specialty heavy rare earth elements (HREEs) are found in uranium wastes in Saskatchewan. It estimated that about 47 tonne/a of heavy rare earth element oxides (HREO) including 27 tonne/a of Y2O3, plus 6 tonne/a of Sc2O3 are in the raffinate of every uranium mill for potential recovery. Since the HREEs are already in the raffinate, cost effective HREE production is promising in Saskatchewan.Selective precipitation including nutraulization, oxalate and double-salts precipitation, as well as sulfide precipitation, ion exchange (IX) and SX are commonly used technologies for the recovery and purification of REE solution. REE oxalate precipitation is an effective technology to remove Fe, Al, Ca, Si and other impurities by taking the advantages of the solubility difference between oxalates of REEs and impurities in acidic solution (Xu, 2005)."

Jan 1, 2017

By R. W. Nice

"The Similkameen Mining Company property is situated about 9 1/2 miles south and west of Princeton B.C. Owned and operated by Newmont Mining Corporation, mining is presently taking place in the Ingerbelle pit. At 15,000 tpd of 0.50% Cu ore the Ingerbelle pit is sufficient for about 8 years. Another 8 years ore supply is available from the old Granby workings of the Copper Mountain property which operated from 1927 to 1957.The pit operations commenced in late 1970 with the concentrator starting in March 1972. Designed and built by Bechtel Corporation under the supervision of Newmont the concentrator's design was based on single-stage crushing and single-stage modified autogenous grinding. The modification was installation of a crusher to crush the critical size build-up. The description of the operation follows.CRUSHERThe primary crusher is an open pocket Allis-Chalmers. 54"" x 74"" gyratory. The basic closed side setting is 8"". The crusher is fed from one side with 100 ton Electra-haul trucks. The crusher pocket discharges to a 96"" wide conveyor belt, then to a 48"" conveyor system including a stacker belt. The crushed product is piled on a stockpile with a capacity of about 30,000 live tons. This stockpile feeds the concentrator."

Jan 1, 1975

By G. Cordingley, A. Mwanza

Lumwana is an open pit Copper mine located in the Northwestern Province of Zambia approximately 80 km west from the provincial capital of Solwezi, approximately 300 km northwest from the Copperbelt and 700 km northwest from the national capital of Lusaka. The mine has two major Copper deposits: Malundwe and Chimiwungo. Copper mineralization includes Chalcopyrite, Bornite and Chalcocite. In addition to Copper, these deposits also contain the undesirable element Uranium contained in vein hosted and disseminated Uranite. The processing plant was designed using conventional technologies: semi-autogenous grinding (SAG) and ball mill for grinding, and mechanical cells for rougher and cleaner flotation. Soon after commissioning in early 2009, it was recognised that two stages of conventional cleaning were unable to produce plant final Copper concentrates with the desired Uranium grades. Studies have shown that a significant quantity of liberated and fine Uranium particles (up to 80-90%) is recovered with the concentrate by entrainment. Lumwana Operations sought the use of the Jameson Cell technology after observing successful implementation at other sites in rectifying similar issues. In late 2009, Jameson Cell pilot-plant test work was conducted at the site and this quickly led to the installation of a full-scale B5400/18 model into the existing cleaner circuit. Inclusion of the Jameson Cell resulted in the plant being able to effectively produce clean and saleable concentrate with Uranium contents consistently below acceptable levels. Initially designed to be used as a cleaner scalper cell at the head of the existing conventional cell circuit, subsequent operational issues with the existing recleaner cells forced reconfiguration of the cleaner circuit and reintroduced the Jameson Cell for the recleaning duty. This paper reports the Lumwana Operation from the first two years of operation where it struggled to produce a saleable concentrate with Uranium grades below 150 ppm, which is the maximum allowable limit set out in the smelting contracts, to steps taken in the subsequent years to implement a satisfactory solution. The plant can now consistently produce a clean Copper concentrate with Uranium grades well below 130 ppm and the overall improvements implemented at site have seen the overall plant recovery improve by 1.3%.

Jan 1, 2014

By R. E. McElvain

"Hydraulic transportation of solids in suspension with water or other carriers, such as oil is becoming more practical as economic situations develop with respect to the railroads and other carriers. Of significant importance, is also the increased size of the major operations and the total impact of larg- er tonnages and more critical sources of supply.There are several means of imparting energy into the solids and directing the material down a pipeline, but the centrifugal pump is emerging as the most practical piece of equipment when considering relatively large flows and recent development. We can now handle relatively high densities without interruptions. This provides the mining and transportation fields a more economical means of lifting and transporting coal and other mineral products.Equipment & MethodsWarman International has developed several methods of alternate PDP against high heads. We have, at least for the present time, shelved our pump which uses clear water to slurry method and have placed our major emphasis on the full development of the centrifugal pump. I personally see several similarities on the alternate reciprocating devices as compared with the steam piston type engine versus steam turbines. The centrifugal pump comes into its most advantageous position at about 2000 GPM and can also show advantages by means of increased mobility, when driving tunnels and in other difficult operations when considering the total economic results. We now have some interesting d<:ta on one 5 mile raw silica sand line designed for pumping at 200-400 tons per h:mr. This is a separate subject on a ""simplified approach to slurry transport"" and paper has been prepared for the Hydrotransport 5 proceedings in Germany this Spring. Reference 1 may be of interest to those who want to delve into the subject further, and I also have some advance copies of this paper."

Jan 1, 1978

By Vu Van Dong

Resource estimation is the science of determining the amount and quality of a given material in the ground that has the potential to be mined at a profit. This is because during this time computers have become more widely available and more powerful and software packages have become more comprehensive and user friendly. Over the past three years The Mining Geology Company with the support from Vinacomin Group has developed the Coal Geological Modelling and Reserve Estimation ? VMG system. The VMG system enables the geological and mining engineer to start at the reserve estimation for the mine design and planning. The VMG system enables the national and international standards (NI43-101, CIM-Canada; SAMREC Code, Africa, and JORC Code, Australia) and user friendly with menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Geological and mining data input through digitized map files and drill-holes information files stored in the database that is an integral part of the VMG system with the main function for collection, validation, and recording, storing and processing of data will include both ?primary? (observation and measurement) and ?interpreted? data. It is recommend that data be stored digitally, using a documented, standard format and a reliable storage medium that allows for easy and complete retrieval of the data. The coal reserve estimation through standard polygon methods with the increased use of these mathematical techniques (geometrical modelling, geostatistical method, least square method, ?) over the last ten years corresponds, to some degree, to a decrease in both the amount of the coal deposit mapping and, in particular, coal seam structural interpretation and modelling, and permit rapidly evaluation of coal seam and overburden quality and quantity. The understanding of the relationship between the coal mineralization of interest and the likely related complicate geological processes and structure that govern its emplacement and geometry within the geological framework is essential to the establishment of the geological controls for coal mineralization. System outputs includes: drillholes summary reports, stratigraphy, cross-sections, isopach maps, structure, contour maps, premining and post mining topography maps, and 3D perspective view on coal seam structure.

Oct 1, 2009

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

By Donald Carlisle

"IntroductionTHE OPINION is held by many persons outside the mining industry, and by some within it, that mine •operators customarily find it advantageous to mine •only the richer parts of orebodies and to leave behind, perhaps permanently, leaner material which could be mined only at a lesser profit. This opinion and the inference which might be drawn from it that 'gutting' of mineral resources is a common feruture• of the mining industry are prejudicial to the intertsts of the industry and deserve careful scrutiny. Oddly enough, a theory of mine economics which gives much support for the opinion was advanced first by members of the mining profession itself, has been repeated •several times in mining literature, and to my knowledge has never been adequately refoted.According to the theory, selective mining of the rich ore first on a large scale will yield substantial gains and these gains do not merely reflect the desire of 'money minded investors' for a quick return but derive from the logical application of compound interest rates and the concept of ;present value. W. O. Hotchkiss and R. D. Parks (1) illustrate the reasoning with a hypothetical example in which an orebody of 4,000,000 tons may be mined either in its entirety in forty years at $1.00 per ton profit or selectively with the recovery of only the richest half in twenty years at $1.50 per ton profit. They show that, with Hoskold rates of 4 and 8 per cent, the present value of profits from mining only the richer 2,000,000 tons exceeds the present value of profits :from mining the whole orebody by about 20 per cent."

Jan 1, 1953

By L. W. Hamel

"DUST CONTROL - GRANISLE COPPER LIMITEDINTRODUCTIONGranisle. Copper Limited is located in the north-central region of the Province of British Columbia, approximately 200 road miles north-west of Prince George. Mill startup was in November, 1966, at a rate of 5,000 tons per day, expanded to 13,000 in 1973. The primary crushing rate is 1,200 tons per operating hour, and the secondary 750, and they can be operated jointly or separately.DUST COLLECTION SYSTEMS There are seven dust collection systems ventilating the crushing and grinding complex. The individual pickup points are depicted on Figure 1 -""Crushing Plant Flowsheet"", and Figure 2 - ""Concentrator Flowsheet"", e.g. 1A, 1B, 3C, etc.System No. 1 - Primary Crusher The feed rock box of the Allis-Chalmers superior 42-65 primary crusher is ventilated by 19,000 CFM of air exhausted directly to atmosphere by a Sturtevant 426 M fixed discharge fan.No. Dust Pick Up Point CFM lA Crusher Feed Rock Box 19,000System No. 2 - Primary Crushing and Screening System No. 2 ventilates the primary crushing and screening equipment. A total of 19,000 CFM of air is exhausted by a Sturtevant 426 M fixed discharge fan through a Howden Type S - size 75 cyclone locally modified for wet scrubbing."

Jan 1, 1976

By M. Sturzenegger

This paper documents a field survey using long-range terrestrial digital photogrammetry at the Palabora open-pit mine, South Africa, for multi-scale characterization of rock mass discontinuities. Stereomodels covering the entire mine were generated based on photographs taken from a distance of 1600m across the pit, using a series of f=20-400mm lenses. Details on the methodology used and its accuracy are discussed. Preliminary results on discontinuity orientation, persistence and intensity are presented, highlighting the effect of observation scale. The potential uses of long-range terrestrial digital photogrammetry in open-pit mine and large natural rock slope environments is emphasized. The use of an f=400mm lens from distances larger than 1.5km may represent an important step forward in the geotechnical characterization of inaccessible remote rock faces.

May 1, 2009

By B. van Beek, T. Goff, P. Gebski, P. Szyplinski, W. L. Ying

"Monitoring the refractory lining integrity is essential to assure the safety of the operators and to determine the remaining campaign life of a furnace. Early detection of refractory lining degradation is essential to avoid sudden furnace failures and prevent unscheduled shutdowns. In the mid-1990s a stress wave propagation technique was developed and since then it has been utilized by Hatch Non-Destructive Testing (NDT) Group to evaluate furnace linings. For the last 17 years the AU-E technique evolved in terms of hardware, software and signal acquisition and interpretation. Most importantly, based on more than a decade of commercial applications, an extensive database of various failure modes, refractory deterioration trends and material properties has been created. This knowledge base is an integral part of AU-E which progressed from a NDT technique towards a comprehensive approach for furnace condition monitoring. All of the improvements introduced over the last several years have greatly improved the accuracy of the measurements. The data analysis process has also become more time efficient making the critical results available to the furnace operators in a more timely manner. Today the AU-E technology is used on a variety of process vessels in non-ferrous, glass, chemical and iron and steel industries.In this paper we are reviewing the available techniques for furnace refractory lining measurement and discussing the pros and cons of each method. The need for continuous improvement and development of new techniques for refractory monitoring is also emphasized. Finally, we are presenting a number of case studies and comparisons between the physical verifications and the AU-E measurements."

Jan 1, 2015

By Chuck Edwards

Whatever your opinion of the validity of the scientific case for global warming, or of the wisdom of the Kyoto Protocol, it would seem judicious to err on the side of caution and try to sensibly minimize global climate change. To this end, we should take prudent steps to minimize our emission of greenhouse gases. Cameco is the world's leading supplier of uranium for use as fuel in nuclear power plants. Cameco’s uranium production fuels nuclear power plants in 16 countries. Nuclear power plants generate clean electricity without greenhouse gas emissions. This presentation describes the role that uranium and nuclear power can have in meeting the growing demand for electricity and at the same time combating global climate change.

Jan 1, 2004

By T. W. Wloder

During recent studies concerning the effects that various surface treatments, surface imperfections, locked-in residual stresses and metallurgical and geometrical notches have upon the mechanical behaviour of metals and, in particular, upon their tension-bending characteristics under impact loads, it became apparent that specially developed methods and samples would be of great assistance in determining the desired data. This paper describes and discusses a number of different types of double-notched tension-bending impact samples which have been considered and examined for this purpose. The types most suitable for exploratory investigations are proposed for application in the study of the _behaviour of metals, their welds, and, in particular, their surfaces, when subjected to various notch-severities, surface imperfections, strain rates, temperatures, and constrained states of stress (i.e. the relations of the three principal stresses). It is expected that the proposed double-notched tension-bending samples and the proposed test methods will also contribute toward further understanding of the cold brittle behaviour and the notch-sensitivities of metals. The possibilities of introducing the so-called impact notch-sensitivity index and relative impact notch sensitivity of metals are discussed. Data obtained on double-

Jan 1, 1961

By Xie Qiang

It is known that the stress state inside rock discs under Brazilian tests is neither simple compression nor tension, but a complex combination of both stress types, as well as for a beam subjected to bending, where compressive and tensile stresses are separated by the neutral axis. In this study, AE generation was obtained on pure white marbles from south Portugal that were submitted to both Brazilian and bending tests. Main questions to be answered were: (1) Does Kaiser effect exist in tests which create complex distributions of tension and compression? (2) Are there any meaningful differences in AE behavior of marble under Brazilian and bending tests?

May 1, 2009

By R. Filippone, Donald Leroux, Colin Hardie, G. Leichtle, Cesar Gomez, Jim A. Finch

"Bubble surface area flux (Sb) is the surface area of bubbles per unit time per unit cross-sectional area of flotation machine. The units are: (m2 bubble surface/s)/(m2 cell) or s -1. For bubbles of mean size db (m), s b = 6-Qg/A db where Qg is the gas rate (m3/s), and A the cell cross-section (m'). This parameter is now receiving wide attention as the possible key machine variable in flotation diagnosis and modelling. The concept is described and the potential use of sb is illustrated by work on flotation columns and mechanical cells. In column flotation of recycled paper, the dependence of ink recovery on s b was the same regardless of size of column or type of sparger. In mechanical cells, it has been established that the rate constant is related to Sb independent of impeller type.The use of s b is limited by the problem of measurement, primarily that of estimating db. A prototype probe designed to estimate db (and hence sb) based on conductivity measurements is described. Exploratory work with the probe in a mechanical cell suggests the promise of making estimation of s b routine.INTRODUCTIONFlotation is the result of interaction among variables associated with the feed particles, chemistry and the machine (flotation cell). Trying to isolate the effects of each aids in process diagnosis and is at the centre of attempts to model flotation. The machine variables that have been investigated include the air flow number, the power number and specific power (Harris, 1976). None have survived as the basis for predicting flotation response perhaps because they did not include directly the properties of the bubble swarm (or dispersion). Recently, Gorain (1 997) explored the relationship between the flotation rate constant and various ""gas dispersion"" parameters notably: superficial air rate (Jg = Qg/A, where Qg is the volumetric gas rate and A is cross-sectional area of cell), bubble size (db), gas holdup (Eg, i.e., the volumetric fraction of a cell occupied by gas) and bubble surface area flux (sb = 6.Jg/db). Of them all, Gorain et al. (1997) conclude that the latter, the surface area flux, correlated best with the flotation rate constant. This concept was adopted from column flotation where it was used to estimate, among other factors, the maximum amount of gas that could be injected (Finch and Dobby), 1990). Let's start by reviewing the concept. Following that some examples of where the concept has been applied will be described to illustrate the current interest and finally we will consider how to measure the surface area flux."

Jan 1, 1999

By W. K. Gowans

The Sullivan Concentrator treats a complex sulphide ore consisting mainly of galena, marmatite and pyrrhotite. The ore carried minor values in silver, antimony, bismuth, indium and tin. The products of the concentrator are lead, zinc, iron and tin concentrates. The minor metal values other than tin are recovered from the concentrates by the refining processes in the smelter at Trail.The concentrator was completed in 1923 and first operated with a capacity of 2,500 tons per day. In the years 1926 to 1929 changes to equipment and buildings brought the operation up to 5,500 tons per day and then, in the years 1935 to 1945, the daily tonnage was raised to 8,500 tons. After 1945, the rising insoluble content of the ore made it necessary to consider the construction of a Sink-Float plant. At this time consideration was also given to the construction of a new crushing plant underground to replace the rolls crushers and cone crushers located at the concentrator. By 1949, construction of the Sink-Float plant was completed along with a new underground crushing plant, and an electric haulage way between the underground crushing chamber and the Sink-Float plant. The ore was hauled in forty 14-ton car trains which discharged into a 3,000 ton receiving bin by means of an air operated five car rotary dumper. With the start up of the,Sink-Float plant, a 1 ½ ft. by 12 ft. Hardinge rod mill was also brought into operation. The Sink-Float plant made it possible to treat 12,000 tons/day of mine run ore with up to 40% of this being rejected as float.

Jan 1, 1975

By T. Imgrund, A. Bischoff, S. Spürk

"Specific conditions of underground coal mines at great depth, such as high temperatures, high rates of methane inflow and natural ventilation pressure provide considerable challenges for the reliable design of appropriate mine ventilation systems. For decades coal mining in Germany has coped with these extreme circumstances. Based on these experiences appropriate software tools for simulating mine ventilation networks have been developed and continuously enhanced. This paper examines differences in the simulation results and underlying calculation methods of two software solutions. The analysis is based on the comparison of FlowNetTM and VentSim DesignTM (Version 5.1) regarding the accurate prediction of fluid mechanical quantities and their validation with real measurements. A special focus lies on exceptional ventilation scenarios typical for deep coal mines, like gas inflows, fire events and buoyancy effects. The purpose of the comparison is the future utilization of the experiences gained during mining at up to 1,500 m depth for state of the art ventilation design. INTRODUCTION Ventilation is an essential component of mine operations—as providing fresh air to workplaces, diluting and removing explosive, toxic or asphyxiating pollutants and assuring sufficient climate conditions. On the other hand, the costs of ventilation contribute to a large extend to the overall operating costs of a mine, as the share in the energy consumption of a mine may be in the range of 25–50% (Belle, 2008). Accordingly, proper design of ventilation systems has been a task since early times. Consequently software for modelling of ventilation networks has been developed in order to improve efficiency and accuracy of calculations (Maleki, 2018). Compressible flow has not been considered by initial ventilation modelling software tools. In Germany, the consideration of changes in airflow density—depending on pressure and temperature—in the algorithms of ventilation simulation software has been started in 1974 by Duepre & Hofbauer. This development had been continued by the Pruefstelle fuer Grubenbewetterung (Test Centre for Mine Ventilation) and resulted in the release of a computer ventilation software named “Wetter”. The mine inspectorate of the German state of North Rhine-Westphalia, which supervises the major coal mining district in Germany, declared ventilation simulation based on compressible flow being “state of the art” in 1985 (Pollak, 1985). This pronouncement made allowance for assessing the consequences of underground fires and downtimes of main fans based on advanced software solutions."

Jan 1, 2019

By S. W. Stogran

"Chemical and limited biological monitoring of mine and mill effluents are being used by regulatory agencies to monitor and control discharges to the environment. Amendments to the Federal Fisheries Act may make it mandatory for mines to conduct Environmental Effects Monitoring (EEM) which will change the emphasis from monitoring effluents to monitoring impacts on receiving waters. The EEM amendments may expand the scope of present environmental studies to include: effluent mixing zone delineation; inventory and classification of resource, habitat, and historical receiving environment; effluent quality determination; chronic and acute bioassay testing; tissue analysis; benthic invertebrate monitoring; fish population surveying; fish tainting evaluation; and the evaluation of impacts on fish habitat, invertebrate communities and fisheries resources. The requirements for EEM have not yet been worked out by the mining industry and the government committee. Experience at Lakefield Research in conducting biological monitoring studies for the mining industry has shown that biological monitoring may be useful for assessing environmental impacts only if programs are planned and executed to collect relevant data, thus minimizing costs and maximizing effectiveness.IntroductionThe chemical monitoring of effluents and water bodies receiving effluents is common practice in the Canadian mining industry and has been used routinely by regulatory agencies to control discharges to the environment. Biological monitoring has also been used on a limited basis, primarily to augment chemical data collected. A number of regulatory bodies, primarily in Canada and the United States, have been incorporating biological monitoring into environmental regulations.Various forms of biological monitoring techniques have been used in Canada and the United States to help assess the impact of mining operations and effluents on the environment. Biological monitoring includes a wide range of activities, from monitoring metal uptake in individual organisms to examining the population dynamics in ecosystems. The most commonly employed biological monitoring techniques are the chronic lethality toxicity tests. Also becoming widely used are in situ and chronic toxicity tests."

Jan 1, 1994