Search Documents

By P. Quinn

"The Venturi-aerated flotation column (VAC) is based on a reactor and separator design for a new generation of flotation machines. The reactor is a Venturi tube, where the air/slurry contact takes place with intensive aeration for efficient particle collection. The separator is a column of 1-3 m length that provides quiescent hydrodynamic conditions for effective separation of bubble-particle aggregates from the remaining slurry.Aeration in the Venturi tube occurs via two mechanisms: air dispersion and nucleation (cavitation). By forcing air through a restricted passage with a fast flowing slurry stream, air is dispersed into fine bubbles. Bubble formation due to cavitation occurs on the surface of particles in the low-pressure section of the Venturi, from dissolved air contained in the liquid.Size-by-size recovery and flotation rate constants were determined for a small-scale laboratory Venturi-aerated flotation column. The results were compared to those obtained in a laboratory 2.2 L Denver cell. It is shown that the Venturi-aerated flotation column has slightly slower flotation kinetics to the Denver cell, but with much higher flotation selectivity. A portable Venturi-aerated flotation column can effectively be used to investigate process or equipment problems in operating plants.INTRODUCTIONFlotation processes can generally be divided into two sub-processes: 1) selective collection of hydrophobic particles by air bubbles and 2) separation of bubble-particle aggregates from hydrophilic particles that remain in the pulp. The methods of aeration, or bubble generation, control the mechanism of particle collection by either collision with, and subsequent attachment to bubbles, or by in situ bubble formation on the surfaces of hydrophobic particles. A flotation device should provide optimal aeration conditions for efficient particle collection and a suitable hydrodynamic environment for effective removal of bubble-particle aggregates from the remaining pulp."

Jan 1, 2002

By Thom Sedun

No sector of the mining industry is more closely tied to local communities than aggregates. Noise, dust, traffic, visuals aesthetics and environmental impacts all fall under the purview of neighbours, local governments and nongovernment organizations. It is no surprise that aggregate operations may not be welcome neighbors in many communities. In British Columbia (BC), the regulatory environment for aggregate operations includes a local component of municipal bylaws and land use-planning in addition to the usual suite of federal and provincial statutes that apply to its sister mining sectors. Additionally, under common law aggregate extraction is not considered to be a land use subject to land use zoning, and some aggregate processing activities can be regulated by zoning. Often traversing multiple local government jurisdictions, aggregate producers find themselves negotiating not only local traffic, but also a mosaic of regulatory environments. There is an opportunity in this present situation to facilitate the application of current technology and practices in the mitigation of many community and environmental concerns associated with aggregate operations. Moving a bulk commodity is a volume-based business, and operators often don?t have time for matters that don?t directly or obviously affect the bottom line. Regulatory agencies often play multiple and complex roles with respect to their industry, not the least of which is the fiduciary role. Balancing how and when to assist an industry is often a difficult decision. For the aggregate industry in BC, the Ministry of Energy and Mines saw an opportunity to assist not only aggregate operators, but also regulatory agencies, local governments, and the general public. Through investing in the Aggregate Operators Best Management Practices Handbook (handbook) project, the Ministry of Energy and Mines (MEM) believes that it will realize a return of upheld community values, enhanced environmental protection, improved regulatory compliance, reduce disputes and a stronger provincial aggregate industry. It is the intent to publish the handbook electronically through the MEM website later this year.

May 1, 2002

By D. Ouellet, G. Gagnon, B. Simser, V. Falmagne

The mining sequence at Noranda’s Bell- Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the redimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Jan 1, 2004

By C. Larsen, I. Orford, L. Strah, M. Renaud, P. Radziszewski

"An AG/SAG mill was commissioned at the Brunswick mine concentrator in October 1998. This paper discusses the original shell top hat liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits.The original liners were chrome-moly steel Norsteel with rubber grates and rubber-lined pulp lifters. The design was based on experiences of other AG/SAG mills and recommendations by the liner supplier, Norcast. Liner design modifications were made in an iterative fashion after observing the wear rate profile of the liners; over ten liner sets were implemented. Shell liner design improvements were supported by a design of experiments approach in conjunction with discrete element method (DEM) charge motion simulations. Design optimization took into account lining costs and impacts on operating performance. The team approach to the liner design improvements process is described with emphasis on the application of the design of experiments. The liner wear history and mill operating performance are presented."

Jan 1, 2005

By Transfert Environment and Society

Transfert?s added value ? Building bridges between project promoters and communities ? Unique expertise in working toward Social License to Operate through meaningful community engagement ? 25 years of recognized innovation and a systematic approach ? Key mining clients: ? Royal Nickel Corporation ? IAMGOLD - Niobec ? Richmont Mines - Wasamac ? Mine Arnaud ? Managem

Aug 1, 2013

By C. L. Popp

The scope is to address issues confronted by parties in the mining industry such as: Mine planners, survey and engineering departments, field teams and subcontractors. Describing approaches and best practices for assembling a project team to identify and create modeling requirements and to implement beneficial results. 3D Machine Control and Guidance tools continue to reduce project risk and attract quality resources with skill sets new to the earthmoving industry. These tools increase production, reduce rework and help with government permitting.

May 1, 2013

By Robert Harris, Peter Pheeney

"The Murray Brook gold mine operated from September 1989 to March 1991. Approximately 1.2 million tonnes of gossan were mined from an open pit and treated at a rate of 900 tonnes per day. The facility applied an agglomeration vat-leaching cyanidation plant for gold and silver recovery. The leached ore or tailings were rinsed of residual gold and cyanide and placed on an adjacent clay lined pad for storage and containment. A 50,000 tonne heap-leach demonstration project was constructed at Murray Brook in 1992 to recover copper and zinc from ore located in a sulfide-rich zone occurring beneath the gossan. The operation proved unsuccessful because of poor recoveries and low metal prices. The project terminated in the same year.A corporate decision was made in September 1999 to undertake complete and final reclamation of the Murray Brook site. Jacques Whitford and Associates Limited were contracted to develop the final reclamation plan and to assist the company in presenting the plan to the New Brunswick government for approval. The government approved the plan in January 2000. Two important reclamation issues were the mobility of mercury from the gossan tailings and the potential of acid mine drainage from exposed sulfides. The mine site is situated upstream of a productive river system, and the issue or impact of chemistry changes to the environment over the long term became an overriding factor in the development of the reclamation plan.A resource assessment of the gossan tailings in 1999 indicated an average concentration of mercury of 40 ppm. The mercury occurred naturally as the mineral cinnabar, but the exposure to residual cyanide (less than 10 ppm) over several years in the pile has likely caused much of the cinnabar to decompose into more soluble mercury forms. The reclamation plan specified the replacement of all sulfides to the pit followed by approximately 600,000 tonnes of gossan. To ensure “fixing” of the mercury, the gossan was replaced in compacted lifts and both the remaining pile and that replaced to the pit covered with available till and compacted. The reclamation work was successfully completed in September 2000 and the chemistry of the receiving environment will be monitored over a three-year period, after which the company expects to achieve walk away conditions."

Jan 1, 2001

By Alex Doll, Derek Barratt

"There is a number of comminution tests commonly used in the mining industry. Many of the tests are used for a particular grinding model or mill sizing program and are incompatible with other tests of different models. This paper provides an overview of the commonly used grinding and crushing tests, which models (or practitioners) use a particular combination of tests and draws some relationships between the incompatible tests based on the DJB Consultants Inc. database of projects.Case studies will demonstrate similarities and differences between major mining districts with some comments about homogeneous and heterogeneous behaviour within the grindability results.INTRODUCTIONThere are a number of bench-scale grindability tests in use for sizing and predicting throughput for grinding circuits. Part of the reason for this variety is there are a number of different grinding models in use in the Industry, and those models operate using incompatible test results as input (Doll and Barratt, 2008).By using the database of testwork in the DJB Consultants, Inc. (DJB) Millpower 2000 database (see Table 1), some of the more commonly used tests are compared and relationships will be drawn."

Jan 1, 2011

By H. C. Counsell, R. Webber

"The mill at Denison Mines' Elliot Lake Operations started up in 1957, with a capacity of 6,000 tons per day. Over the years various plant modifications expanded th.is to 7 500 tons per day. In 1976, management decided to carry out a major expansion of the milling capacity, and during 1980 the grinding capacity was increased to 15,000 tons per day.The original comminution system consisted of a conventional crushing plant feeding minus S/s-inch material to rod and pebble mills, in closed circuit with mechanical classifiers. The key decision that had to be made was whether the expansion should include conventional or autogenous grinding flow sheets.During 1977, extensive pilot plant studies at Lakefield Research showed that two-stage semi-autogenous grinding, with some steel media in the primary mill and with pebble media in the second stage, produced stable grinding conditions. This type of circuit was selected by Denison for the expansion, and went into production in 1980. Primary millThe flow sheet of the semi-autogenous grinding circuit is shown in Figure 1. The primary grinding mill is a Koppers 28 foot by 10 foot mill, driven by a 4,000 h.p. synchronous motor. It is fed with a minus 8-inch run-of-mine ore, and 4-inch grinding balls are added as supplementary grinding media. There are two Koppers 15.5 foot by 22 foot secondary pebble mills, driven with 1500 h.p. synchronous motors. Each grinding stage operates in closed circuit with cyclones, and the primary cyclone overflow is the feed to the secondary mills. The circulating load in the primary stage can be controlled by adjusting the cyclone apexes."

Jan 1, 1984

By Rodrigo Toro, Ivan Yutronic N

"The Copper Concentrator Plant of Compañía Minera Doña Inés de Collahuasi (CMDIC) is composed of three grinding lines, the third one being the largest. Due to the capacity feature of the third line, specially its SAG mill, it is a priority that the advanced process control team of the Company deploys a supervisory control strategy that allows this unit to operate in an optimal way, in order to achieve the maximum productivity at minimum cost. It is in this kind of tasks where advanced control applications play a key role in obtaining the best economic profit of the process.The advanced process control team, formed by people from Informatics, Automation and Operations of CMDIC have assumed the challenge of generating the transition from a manual SAG Mill 1011 operation (40 x 22 feet, the largest copper SAG mill of the world), to a fully automatic SAG Mill using a multivariable control strategy instead of a rule based on expert control system (widely used in industrial mining process control applications).Therefore, CMDIC decided to work together with Honeywell APC Team implementing an advanced automatic control strategy for the SAG Mill 1011, using for this purpose a technology called Model Based Predictive Control (MPC), based on a variety of control methods that uses dynamical models of the process, obtained from input/output data, in order to print the process knowledge into a group of mathematical relationships that links the constraints (controlled variables) with available commands (manipulated variables) and measured disturbances.The main objective of the advanced control strategy is to ensure process government, tending to throughput stability and optimization, by the execution of coordinated control actions, proactively avoiding measured disturbances effects and the SAG mill overloading.The most important benefits of using a multivariable control strategy are: the automated operation of SAG mill 1011 (that was manually operated before the implementation of this application), a safer, more coordinated and more stable process operation, achieving through this an increase of throughput and a decrease of specific energy consumption, controlling the amount of oversize material production, power consumption, mill loading, noise and torque. In addition to the operational results, this challenge has consolidated a control team, with the participation of engineers and operators, diminishing the typical implementation time and achieving a greater use of the application in a short time."

Jan 1, 2010

By Walter S. Bergholz, Michael L. Schreder

"Since Escondida began operations in fiscal 1991, a series of aggressive expansion projects have enabled market share to be increased and ever larger profits to be realized. This was possible due to the very large size of the ore body and its high grade - averaging 2.7% copper from startup through fiscal 1997. The situation has now changed: ore grade is falling rapidly and is projected to be only 1.55% by 2003. Since revenue is directly proportional to ore grade, while costs are proportional to quantity of ore processed, profits will begin to fall dramatically. The Phase IV Expansion Project is intended to forestall this drop in profits by increasing ore processing capacity by over 85%.The Phase IV concentrator is designed for a nominal capacity of 110,000 MTPD and the key to achieving this value is through the proper design of the grinding circuit. This paper presents the general design criteria for the grinding circuit, as well as a description of the facility.INTRODUCTIONThe Phase IV Expansion Project consists of a new copper concentrator located 8.5 km south of the existing operations, a new tailings disposal and water reclaim system, a new concentrate slurry pipeline to the coast, and added concentrate handling capacity at the port of Coloso. The new concentrator has a nominal capacity of 110,000 tonnes per day (MTPD), compared to the existing concentrator’s capacity of 127,500 MTPD. The Laguna Seca concentrator is based on using the largest and most efficient ore grinding mills now available.The concentrator has been designed for a 110,000 MTPD nominal capacity. The process design criteria for the Phase IV project were established from in-house operating information and from test work. Unlike a green field project, Escondida already had an operating plant and it processes ore from the same pit that feeds the Phase IV plant. It is expected that the current mineralization will be similar for the first 6 years of operation of the new project. Therefore, some of the current plant operating conditions were incorporated directly into the design criteria."

Jan 1, 2004

By P. Dyas, H. Zouitt, D. M. Smith

"Falconbridge Copper's Lac Shortt gold mine is located in northern Quebec approximately 300 km northeast of Val D'Or and 100 km west of Chibougamau (Pig. 1). Engineering for the mill commenced in early 1983 with a feasibility study. The plant was commissioned in the fall of 1984 at a capital cost of approximately $12 million. Design capacity was 750 tpd which was increased in the fall of 1985 to the current level of 1200 tpd.The ore at Lac Shortt is free milling, grading an average of 5.5 g/t gold which is finely disseminated throughout the host rock. Pyrite at 3 to 5% by volume and traces of copper mineralization are also present.Some of the latest gold processing techniques known at the time of design were incorporated into the mill. These include carbon-in-pulp, pressure stripping, electrowinning of pregnant solution and induction furnace refining. The plant also features several innovations such as a unique interstage carbon retention screen in the CIP circuit and the outdoor location of the cyanidation feed thickener, mill solution tank and reagent storage silos despite -40° Celsius winter temperatures.This paper describes the current mill process and discusses some of the problems encountered during the first two years of the plant's operation. CRUSHINGThe Lac Shortt surface crushing facilities are located in a separate building, isolated from the wet processing circuits for dust and noise control reasons. The crushing plant equipment was originally utilized at the Manibridge operation in northern Manitoba where it had been designed to operate at 135 tph. However, at Lac Shortt a rate of only 80 tph has been achievable to date, mainly due to the hardness and frequently slabby breakage characteristics of the ore. Therefore, in order to meet fine ore requirements at the current mill throughput of 1200 tpd, the crushing circuit is run seven days a week. 24 hours a day. Availability has been averaging 65%."

Jan 1, 1987

By Masayuki Ishikawa

In a radio frequency and optoelectoronic device packaging, Gold-Tin (Au-20 wt% Sn eutectic) solder is used widely due to the excellent electrical and thermal conductivity, high strength, and negligible creep characteristic under repetitive thermal cycling. With the recent lead-free movement, Gold-Tin solder is recognized as an alternative material for high temperature Lead-Tin solder. Generally, Gold-Tin solder is supplied in the forms such as ribbons, pellets, and ring frames. However, these forms must be set-up accurately on the joint area to press chips in bonding, therefore, it is difficult for these forms to satisfy the recent requirements for the down sizing in the connection areas. On the other hand, Au-20 wt% Sn solder paste can be applied flexibly to various supplying methods, such as printing, dispensing system and pin transcript. These methods also make it possible to reduce the production cost. However, in the case of using the solder paste, the void issue is one of the most undesirable problems. The void causes the degradation of the characteristics such as the bond strength, electrical characteristic and thermal conductivity. We have been intensifying the development of the void free paste, and have achieved void reduction by optimizing the powder size, the flux composition and the reflow condition.

Oct 1, 2003

By Hans von Michaelis

"INTRODUCTIONThe renaissance in gold and silver recovery technology has continued to unfold and it is appropriate to review some of the useful new technologies as well as try to identify some of the industry's future needs and frontiers.The remarkable strengthening in the US dollar has resulted in a relatively low gold price in US Dollars of around $310/oz at the time of writing and silver at $6.25/oz. This general softening in the dollar prices and the recent confusion as to environmental compatibility of cyanidation tailings and effluents, has led to a slowdown in announcements of new operations. Another reason for the slackening off in the USA is that in the past few years a large part of the capital has come from oi I and gas companies that now seem to be losing interest in mineral ventures, and foreign investors for whom the dollar is becoming out of reach. In the author's opinion this represents an unprecedented window of opportunity.Elsewhere in the world where local currencies have weakened, the price of gold is at or close to its all time high.For example, in South African Rands, the gold price was R571.00/oz when the rand was US$1.47 and the gold price reached US$800. Now at US $309/oz and with the Rand at US$0.51 = Rl .00, the local gold price is R600. The price of si Iver in Mexican pesos is not much less than it was when silver reached US$50/oz. Gold, and silver prices in local currencies outside North America are still buovant and at levels where additional investment in new projects is more encouraging.Even in Canada where the dollar is worth about US$0. 75, this provides a smaller but significant cushion compared with US operations. Considering the present strength of the US dollar and even the Canadian dollar relative to many other gold producing countries, there should be significant investment opportunities at today's prices. Mining companies have started to descend on Brazil, for example, where in a matter of just a few years annual gold production has increased from 10 to 70 tons. In South Africa, a Canadian company backed by Swiss financing has been able to take over a Witwatersrand gold mining operation and is installing a huge new tailin9s retreatment plant to process about 1 million tons per month of tailings."

Jan 1, 1985

By J. E. Nesset, S. R. Rao, J. A. Finch

"For base metal sulphides, iron rejection starts in mineral processing. This review focuses on changes in plant practice specifically to improve iron sulphide rejection by control of contaminant ion effects and discusses selected general innovations in mineral processing that can be expected to play a role. One group of changes to control contaminant ions is in size reduction (the use of stage grinding and inert stirred milling) and another is in system chemistry (order of reagent addition and exploitation of the flexibility of sulphoxy reagents). Plant examples illustrate the successes, indicating that there are several options available. The general innovations start by considering the new tools for measuring gas dispersion properties and quantifying froth characteristics by imaging. Examples of their application to improve concentrate quality illustrate the potential. Other innovations stress adapting geostatistics to model variation in milling and flotation response to provide feed forward control and rigorous application of statistical experimental methodology in plant test work. An example from one concentrator shows improvements in concentrate quality from application of basic principles can be impressive.INTRODUCTIONThe more iron control (rejection) that can be accomplished in mineral processing the lower the subsequent metal extraction costs and environmental implications of iron disposal, particularly in hydrometallurgical processes. Iron rejection has been a contributing target to periodic attempts to apply mineral processing to nickel laterites and bauxites but the prime application is control of pyrite and pyrrhotite (iron sulphides) in the treatment of sulphide ores by flotation. In this paper some new concepts and innovations introduced in sulphide flotation plants over the past ten years or so (i.e., since a previous review [1]) will be outlined with examples of how they have contributed to improved “iron control”.To increase rejection of iron minerals, first the recovery mechanism should be understood. There are four principal ones, two physical in origin: 1, via locked particles (i.e., flotation of composite particles due to insufficient size reduction to liberate the minerals) and 2, through entrainment in the water reporting to the float product (an unselective process); and two originating from a response to the system chemistry: 1, true flotation (i.e., iron sulphides becoming hydrophobic) and 2, as a result of iron sulphides forming aggregates with hydrophobic particles (e.g., ”slime” coatings). There has been considerable effort to diagnose which of these dominates iron sulphide recovery; in many cases it is due to “chemistry”, in particular true flotation. The flotation effect often appears related to contamination by metal ions [1]. This can reduce selectivity in two ways: 1, metal ion species may activate iron sulphides, or 2, cause general depression which demands more vigorous flotation conditions (e.g., additional collector) with consequent loss of selectivity. This is where the review will start, by considering ways to control contaminant ions."

Jan 1, 2007

By Richard Klimpel

"Over the last 15 years, there has been a number of plant scale sulfide mineral flotation tests organized by this author specifically aimed at understanding how flotation rate varies with reagent type and dosage. With regard to the Interaction of collector dosage, particle size, and frother type, the eight specific trends listed in the paper (Illustrated with data from two specific case studies) are qualitatively the same for almost all plants studied in some depth. The Interaction of flotation rate K and equilibrium (Infinite time) recovery R in the plant has been denoted as the R/K trade-off. The effect of collector dosage on the rate of flotation of specific particle size intervals is particularly interesting and once understood, is quite useful In understanding how industrial flotation plants respond to changing reagent type and dosage. The location and magnitude of the R/K trade-off can be different for various ores and various plant configurations, but the RIK trade-off is almost always present. The purpose of this paper is to clearly describe and illustrate the nature of this very Important flotation system Interaction so that operating engineers have a starting reference point for beginning successful plant Improvement studiesIntroductionIt is well recognized by industrial froth flotation plant operators that improving existing sulfide circuit performance is often difficult due to the self-compensating systems nature of the froth flotation system, e.g. Klimpel (1988, 1989, 1995). Extensive plant testing with existing and new reagents by this author throughout the world has clearly shown that one of the more important self-compensating mechanisms is the Interaction between collector dosage, frother type, and particle size. The term self-compensation in flotation simply means that as the plant operator consistently changes one parameter in the same direction, the nature of the froth flotation system Is such that the circuit will eventually begin to resist this controlled parameter change by automatic (uncontrolled) changes In other parameters and the overall circuit performance will go through a maximum or minimum (hence causing the operator to stop the parameter change)."

Jan 1, 1997

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019

By Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hard rock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

May 1, 2007

By Michel Doyon

Canadian Context: Exploration ??Space Exploration is within the unique mandate of the Canadian Space Agency ??Global partnerships ??Maintain close relationship with our partners ??New knowledge in S&T ??Retain and attract highly qualified personnel ??Participation in missions leads to design roles in industry and academia ??Collaboration between government laboratories, industry and academia

May 1, 2009

By B. M. Coombes

The McCracken and Stacey (1989) method of assessing geotechnical risk for largediameter raisebored shafts has been the basis for most Australian pre-construction raisebore investigations for the past 20 years. At the time of its publication, the McCracken and Stacey (M&S) Method did not include a database of raisebore diameter and rock mass conditions versus actual performance. It did, however, provide a chart that quantified geotechnical risk in terms of proposed shaft diameter and the raisebore rock quality index, QR. Two parameters, RQD/Jn and Jr/Ja were identified as being critical to raisebore stability, but the contribution of these to overall raisebore stability was not quantified. Peck and Lee (2008) published a database of raisebore performance from Australian case histories. Raisebore diameter and ground conditions, in terms of a Lower Bound QR value, were presented for 50 cases versus raisebore performance. This paper updates the database with further case histories and corrected SRF values. This paper further evaluates the reasons for the variable raisebore performance for similar RSR values. For all case histories, three parameters, RQD/Jn, Jr/Ja and Jw/SRF are investigated to assess their influence on raisebore performance.

May 1, 2011