Search Documents

By R. C. Hartviksen

"The Drumbo Mine is a new gypsum mine located at exit No. 32 of Highway 401 between Woodstock and Kitchener, Ontario. The flat-lying 6-foot (1.8-metre) bed of gypsum is near the base of the Silurian Salina Formation, about 380 feet (116 metres) below surface. The mine is owned and operated by Westroc Industries Limited. A shaft, 12.5 feet (3.81 metres) in diameter, was drilled and then lined with a liner-sinking technique new to this continent. The shaft was completed in the fall of 1977. Gypsum production was started in December 1978, employing a conventional room - and - pillar method of mining.Historical BackgroundA brief mention of gypsum in the Drumbo area is included in a survey of the Ontario gypsum industry by Guillet. This occurrence was discovered in 1958 when National Gypsum conducted some widespread diamond drilling. Western Gypsum Products Limited acquired leases in 1960 and concentrated a drilling program in Blenheim Township near the village of Drumbo; 79 holes were drilled in an area of 1900 acres (770 hectares). Mining rights were then acquired for 170 0acres (690 hectares). A test shaft, 44 inches (1.1 metres) in diameter, was drilled to obtain a 50-ton (45-tonne) bulk sample. This opening will be used as an emergency escape way and for ventilation.Westroc Industries Limited, a wholly owned subsidiary of BPB Industries, has its head office at Mississauga, Ontario and operates gypsum board plants at Mississauga, Vancouver, Calgary, Winnipeg and Montreal. Other gypsum mines are at Windermere, B.C. and Amaranth, Manitoba."

Jan 1, 1983

By P. Maltby

"Smelter Feed Preparation Falconbridge Nickel Mines Limited, Sudbury Operations, operate 4 mills and a smelter to produce Bessemer Ni-Cu matte for refining in Norway. Approximately 1400 tons of Ni-Cu concentrate are produced daily which are dried from a filter cake containing 14% moisture to 7.5% moisture pellets. Concentrate drying is done by 4 rotary dryers as shown in the 'Dryer Performance Data' at four separate locations. The dryers all form part of the feed preparation stage prior to sintering.The rate at which concentrate can be produced through the Sinter Plant largely depends on the quality of the dried product which makes up the feed. A feed consisting of mostly hardened pellets will sinter much faster than a feed which consists of broken pellets and dust. Dryer products require:1. Good green strength to survive shipment and handling.2. Correct moisture content.3. Sizing within a range ideally from 1/4"" to 10 mesh in diameter.Dryer performance data is shown in Table 1. Capital costs between the two types of dryers are comparable with the Roto-Louvre producing generally a larger better-formed pellet. Dryer feeds differ in that at both Hardy and Fecunis, Ni-Cu concentrate filter cake is the only feed while at the Falconbridge slurry plant the dryer feed can consist of up to 10% by weight of smelter flue dust resulting in a combined concentrate-dust pellet for feeding to the Sinter Plant. To the Falconbridge Sinter Plant dryer, dust and limestone are added for the smelting process in addition to Ni-Cu concentrate."

Jan 1, 1972

By Luis R. Fonseca, C. Raimat, C. Wendeler, A. Sanz

"Rockfall barriers are widely known as proven efficiency element to protect infrastructure by catching the rock blocks in the falling direction and absorbing the energy generated by them.It’s common in the project design phase and during installation, fix rockfall barriers for catch a high percentage of the falling blocks and in many cases consider as valid the solution when the barrier can capture all of them. However, in many cases it’s possible to consider the use of these protections, simply to guarantee a secure shed for the traffic and intercept simply the blocks that theoretically hit the road surface.The results of the high-energy rockfall protection barriers type GBE which protect GC-200 road in Las Palmas de Gran Canaria are shown in this paper.The topographic data should be especially detailed observed and even more if you want to apply the technique of ""shadow zone"" with a flexible gallery system. It should be drawn from detailed topographic maps and drawings (photogrammetric restitution) to the scales 1/1000, 1/500, or 1/200; and it is important not to ignore the presence of vertical cuts, tracks, small slopes that modify the trajectories (trampoline effect, hard points that favor the rebounds) and which are not always presented in the drawings.The ""shadow zone"" is defined as the protected area, located at a lower elevation to the line created by the rockfall barrier to except of trajectories of rocks and free from the influence of the deflection of the system under the maximum energy level for which it was designed (MEL)."

Jan 1, 2015

By C. F. Harris

Following the initial development of the zinc-lead blast furnace, efforts have been directed both at increasing the scope of the process and increasing the cash return. The paper reviews the process developments which enable the process to smelt efficiently a range of material which encompasses high-grade zinc sulphide concentrates. mixed concentrates, Waelz oxide, zinc ashes and other materials blended to give a furnace feed ranging from 25 to 65% zinc and from 1 to 25% lead, with a copper-lead ratio exceeding 1 to 8. The paper also reviews the process developments which have enabled the capacity of a furnace and condenser system of standard size to be boosted from 30,000 to 80,000 tonnes/annum. The benefits achieved are used as a justification for continuation of the development of the zinc-lead blast furnace. Predictions are made of the benefits expected from further developments.

Jan 1, 1979

By C R. Evans

Whole-rock and muscovite potassium-argon dates from selected low-grade metamorphic rocks of Precambrian age in the Canadian Rocky Mountains near Jasper, Alberta, were obtained to ascertain the age of the source terrain and the age of the metamorphism. Ten argillites gave whole-rock dates ranging from 270 to 485 million years, dates which are apparently inter-mediate between the age of the source material and that of the metamorphism. "Up-dating" increases with the degree of orientation of muscovite in the cleavage plane, and with the ratio of the muscovite in the cleavage plane to that in the plane of the bedding. Detrital muscovite from four arenaceous rocks gave dates ranging from 1,050 to 1,780 million years. "Updating" increases with decreasing grain size, so that, within the range investigated, the cube of the median diameter (¢) of the muscovite is apparently proportional to the radiometric date.

Jan 1, 1964

By Z. -E. Nakagawa, O. Yamamoto

After the formation of a concentration gradient of SiC within C-C composite, either zircon or mullite thin films were coated on the surface by sol-gel process. Oxidation resistance tests of as-prepared composites with a couple consisting of a ceramic thin film and a SiC-gradient were then carried out in air at the temperature range from 600 to 1600°C. By the coating of zircon with a thickness of 1.5 µm, a pronounced oxidation resistance was observed; the mass loss by oxidation was almost negligible at 1000°C and one hundredth of original composite at 1400°C. In the case of the coating of mullite with a thickness of 1.0 pm, the marked improvement in oxidation resistance over the whole temperature range examined, from 600 to 1600°C, was found with the combination of a SiC-gradient and a mullite thin film

Jan 1, 2004

By A. A. Lavrinenko, N. I. Gluhova, L. M. Sarkisova, D. V. Makarov

"The investigated sulfide Cu-Ni ores are characterized by low PGE contents and emulgated impregnations of pentlandite and palladium minerals in the main ore-forming mineral pyrrhotite, which hinders their selective separation, requiring a collective flotation of sulfides to concentrate, and hydrometallurgical processing. As revealed by studies of floatability of Pt-Cu-Ni ore in a mixture of butyl xanthate and chelating phosphorus containing reagents, the most effective additive is Aerophine 3416 (a phosphinates mixture) manufactured by Cytec. Using collective flotation with a butyl xanthate – Aerophine 3416 composite in the ratio of 1:3 has afforded to enhance the Pt, Pd, and Ni recovery by 13.6 %, 9.2 %, and 9.4 %, respectively. The optimal ratios of Aerophine 3416 to butyl collector for the collective flotation are the following: 1:1 for Pt and Pd and 3:1 for Ni. The effect of these reagents on the electrode potential and surface hydrophobicity of pyrrhotite, pentlandite, and platinum black has been investigated. The extraction UV spectrophotometry experiments demonstrate that DIBDTPI exists on the pyrrhotite surface mainly in the form of disulfide in weak acid medium and in the form of compounds with Fe on the mineral surface in minute amounts. There appears some disulfide and few amount of (DIBDTPI)2Ni on the surface after interaction of DIBDTPI and pentlanditeINTRODUCTIONXanthates are widely used in flotation of copper-nickel ores containing platinum group metals (PGM) as sulfides collectors which can concentrate the most part of PGM connected with the sulfides. Though xanthates are hardly efficient for flotation of free PGM, the latter are floated more slowly compared to the sulfides of base metals. The reasons for poor floatation of free (mineral) forms of PGM are under-researched, however the key accepted reasons are: fine disseminations of free PGM, insufficient interaction with xanthate and negative influence of blue copperas and sulfur-containing ions which are sulfides oxidation products (Penberthy et al. 1999; Shackleton et al., 2007). That’s why an additional collector, normally dialkyldithiophosphates, is used during flotation of PGM-containing copper-nickel ores. A reagent DP-4 is used for recovery of PGM at Norilsk mining and metallurgical plant. The reagent represents a slightly-soluble organic calcium sulfonate which is given to flotation pulp in the form of water emulsion of 5% - solution in automotive diesel oil."

Jan 1, 2016

By F. R. Archibald

MR. A. F. B. Norwood: Having been associated in the past few years with nine different plants roasting aurif erous concentrates in Australia, two of which were new installations for which design and construction were undertaken by the writer, I read Mr. Archibald's paper with very great interest, and I deem it a great privilege, as a member of a sister Institution, to be invited to contribute to the discussion on the paper. I wish to congratulate the author on a very informative and interesting paper, and, although situated many thousands of miles away, I feel I have gathered from it a very close idea of the operating conditions and of the work that has been carried on at the Beattie gold mine. Working along somewhat different lines, it is interesting to note that the conclusions drawn by the author run closely parallel to those accepted in Western Australia, viz., that the object of roasting is to obtain a porous calcine, and that this can best be achieved by roasting first at a temperature below 900 deg. F. to 1,000 deg. F., and then raising the temperature at the finish of the roast. Turning first to the laboratory work, the materials I have studied in Western Australia cover a range from those with little or no arsenic to concentrates carrying as high ?as 20 per cent, i.e., even higher than in the analysis quoted for the eoncentrates from Nepheline Products, Limited. In the ease of arsenic-free pyrite concentrates, the roast is ideally carried out at a temperature ranging from 900 deg. F. to 1,000 ferric oxide is one cause of the refractory gold remaining In deg. F. No improvement in extraction is obtained when the calcines are cyanided by raising the final temperature above this point; nevertheless, in technical practice it is desirable to finish the roast at 1,200 deg. F. in order to decompose basic ferric sulphate and thereby reduce the consumption of chemicals in the subsequent cyanidation step. However, if at any stage of the roast the temperature is raised above 1,200 deg. F., the extraction by cyanidation falls, and continues to do so the higher the maximum temperature that is reached. Line A in the accompanying graph typifies this effect.

Jan 1, 1949

By Aalbert Zwijnenburg

One of problems connected with the use of gold/titania-based catalyst systems is the low yield in propene oxide (up to 2 wt %). It is shown that the low propene oxide yield is due to product inhibition. New options for propene epoxidation with hydrogen and oxygen are discussed. INTRODUCTION The direct gas-phase synthesis of propene oxide (PO), by the use of molecular oxygen, is still aimed for. Agbased catalysis is in principle possible, but selectivity at present is not promising. Highly dispersed gold on titanium containing catalysts show an extraordinary selectivity in the oxidation of propene to the corresponding epoxide (> 99 %), using a combination of H2 and O2 as oxidation mixture [1]. Additional studies of the epoxidation reaction have indicated several drawbacks of the Au/TiO2 catalyst. Firstly, the low conversion (1- 2 %) obtained under typical reaction conditions (atmospheric pressure, 323 - 423 K) cannot be increased by increasing the reaction temperature, because this leads to extensive by-product formation. Secondly, the low efficiency of hydrogen (relatively large amounts of water are formed) is hard to prevent. Finally, significant deactivation of Au/TiO2 catalysts within several hours on stream has been observed. Deactivation can be almost completely prevented by using dispersed TiO2 supports, such as TiO2/SiO2 and Titanium-Silicalite-1 (TS-1) [2]. In recent literature [2,3] a hydroperoxide-like intermediate has been proposed to be responsible for the selective epoxidation. This oxidising species is said to be formed over gold and subsequently used for epoxidation over the Ti-containing support. The support is responsible for the slow desorption of PO. One of the problems for future industrial application might be the low yield in propene oxide. Furthermore, the presence of minor amounts of by-products, not detected on lab-scale catalyst testing, might complicate the separation unit in an industrial process. The reason for the low PO yield over Au/TiO2-based catalysts will be discussed in this paper. Temperature Programmed Desorption (TPD) and micro-flow experiments have been carried out to study PO desorption and catalyst performance, respectively. A catalytic cycle is proposed together with its consequences for the maximum yield in PO. Finally, several process and catalyst options are discussed in view of potential future industrial application.

Oct 1, 2003

By Weimin Fu

Chondrite-normalized rare earth elements (REEs) profiles and high field strength elements (HFSEs) in rocks and minerals represent important tracers of geological processes. Of these the birdwing-shaped profile with negatively-sloped light REE ((La/Sm)N >1), positively-sloped heavy REE ((Tb/Yb)N <1), and strong negative Eu anomalies is commonly associated with large-scale hydrothermal systems or granitic intrusions. In a different way, severe deviation of Nb/Ta, Hf/Sm ratios from those of chondrite may also indicate hydrothermal signatures in the rocks involved as these ratios are generally stable and chondritic in normal magmatism as a result of their nearly identical ionic radii and charge. In this study, we present a typical setting where birdwing-shaped REE profiles together with Nb/Ta, Hf/Sm ratios unusually higher than those of chondrite, are systematically developed in a series of garnetite, quartzofeldspathic gneiss, Fe- or Mg-rich aluminous gneiss, and sulfides and magnetite. These units and associated Cu-Au mineralization form a VHMS-style hydrothermal system in the granulite-facies 1.4 Ga -1.35 Ga volcano-plutonic, arc-related Bondy gneiss complex (BGC), western Grenville Province, Canada. Outside the recognized hydrothermal system of the BGC, such REE profiles are not observed. Instead the surrounding felsic and mafic gneisses display primary trace element characteristics of island-arc magmas, suggesting that granulitefacies metamorphism did not modify significantly the trace element signatures of the protoliths. Although magmatic fractionation of accessory minerals can produce birdwing-shaped profiles, it cannot explain the extreme fractionation of isovalent trace elements (Nb-Ta) and the high Zr content of the hydrothermal rocks. Neither is it compatible with the lack of significant Nd depletion that would normally incur during this process. Following our study, we demonstrate that F-rich fluid and mineral phases enriched in LREEs and HREEs respectively must have been involved in the main hydrothermal alteration and REE fractionation process in the BGC. Preferential removal of REEs from the interstitial glass of the volcanic protoliths together with dissolution of plagioclase and subsequent external influx of HREEs and HFSEs can produce birdwing-shaped REE profiles. In turn, such profiles and/or unusual Nb/Ta, Hf/Sm ratios can be used as a sensitive marker of hydrothermally altered rocks in targeting mineral exploration.

May 1, 2003

By R. C. Gilmore, J. McMack, G. E. Bogin, J. F. Brune, C. DeRosa

"Researchers at the Colorado School of Mines are designing and building a 1:40 scaled physical model of a fully operational longwall coal mine. The purpose of the model is to minimize the occurrence of methane explosion hazards by testing various ventilation strategies and determining optimal methane sensor placement throughout the longwall face. Fluid scaling factors were analyzed using Computational Fluid Dynamics software Ansys FLUENT™ at both full and 1/40th scales. Researchers were able to identify key scaling factors and subsequently developed suitable flow parameters that would maintain full scale accuracy of flow patterns in the 1/40th model. KEYWORDS Coal, Longwall, Methane, Explosion, Scale Model, Ventilation, Fluid Dynamics, Richardson, Gob, Porous INTRODUCTION Mine ventilation systems are a key component for ensuring a safe working environment by introducing fresh air from the surface and diluting explosive gases and hazardous contaminants. This holds true for longwall coal mines where the emission of flammable methane gas from the longwall face as well as the gob can create explosive mixtures of methane and air. Therefore, an effective ventilation strategy can help mitigate the potential for accidents within a mine. Developing an effective mine ventilation system (MVS) requires a detailed understanding of the physics of gas transport and how this relates to specific geometries and obstructions in the face. Researching this phenomenon requires the development of computational fluid dynamics models capable of simulating fluid flow and methane species transport that can be validated through physical experimentation. Unique site conditions determine ventilation layouts for every coal mine. Researchers have designed a 1/40th scaled physical model of a longwall coal face and adjacent gob that includes movable shield supports and a movable shearer with rotating cutter drums that can be adjusted to a variety of ventilation conditions. The proposed work will address the need for an improved Mine-wide Atmospheric Monitoring System (AMS), and provide the ability to link existing MVS models with AMS in real time. By accurately representing the coal face, the gob area and the mining equipment, gate roads and bleeder entries, the scaled model accurately represents all relevant structures, geometry, and dynamic conditions. A Plexiglas cover allows full optical access for sensor equipment as well as visual inspection of the fluid flow and species transport."

Jan 1, 2019

By R. Ghomashchi

Wear, fatigue and corrosion are the most widely encountered modes of failure in materials used in engineering applications, including aero-gas turbines. Although wear is distinctly classified as adhesive, abrasive, erosive, fretting and so on, there are usually more than one wear mechanism involved in the failure of components in service because there are many systems and materials variables active in materials wear that makes it more difficult to study. This is further complicated by the discrepancies between the results of laboratory tests and field data. The present investigation was set up to examine the wear characteristics of M50 and T1 high-speed steels at both room and elevated temperatures to draw a thorough understanding of the wear behavior of this class of high-speed steels. This article focuses on the mechanical and microstructural characterization of wear for T1 and M50 high-speed steels using a pin-on-disk wear machine.

Jan 1, 2005

By L. Kilpinen, K. R. Kay, H. B. Fowler

"FOREWORDThe International Nickel Company of Canada has built four ore concentrating plants since 1950. The fifth and largest is now under construction. In each successive plant, the level and type of instrument control and sophistication of control techniques have increased as experience was gained. The type of control progress is illustrated in Fig. 1.At Frood-Stobie the high degree of instrumentation and the level of control were made possible by the constant evolution of techniques and improved instrument hardware technology. We have established in practice concepts that are sound, although many modifications to instrument sensor types and locations 1-rere often necessary. It is generally true that at other existing Inco mills, it is possible to run ""all manual"" for protracted lengths of time because of operator availability and dependence. The Frood-Stobie Mill is the exception, and it is the degree of reliability of the instrumentation hardware and level of maintenance that has made this possible."

Jan 1, 1971

By M. Tanaka, Y. Sato, H. Narita, S. Alam, T. Ogata

To ensure a stable supply of rare earth elements (REEs), it is highly necessary to establish the corresponding recycling technologies for RE magnets and phosphors in inplant wastes and endoflife products. Solvent extraction using 2ethylhexylphosphonic acid mono2ethylhexyl ester (EHPNA) is often applied in the separation and purification of REEs. In this study, the equilibrium distribution ratios of neodymium and dysprosium between 1 mol/L nitrate solution and the EHPNA in an alkane diluent were measured at 298K. The experimental data were analyzed by correcting the nonideal behavior of the organic phase using the Alstad empirical equation under the assumption that a complex with a molar ratio of 1:6 (REE:extractant monomer) was formed. The model correlated well with the experimental data and the extraction equilibrium constants were obtained. The extractant equilibrium constants obtained by this methodology would be useful in the design of REE recycling processes using solvent extraction.

Jan 1, 2014

By P. Wanjara, M. Xiao, M. Jahazi, C. Poon

Using a robotic 4kW Nd:YAG-laser system, Inconel 718 (1 mm sheet) was welded with and without filler wire to investigate the effect of processing parameters, including power input and welding speed, on the weld geometry, microstructure and mechanical properties. By means of both nondestructive testing and microscopic examination, the weld quality was studied to determine the nature of the welding defects (porosity, cracking and bead shape) over the processing range of 3-3.5 kW for the power input and 4.5-6 m-min-1 for the welding speed. Application of the design of experiment methodology permitted the examination of the relationship between the process parameters and mechanical properties, from which the optimized laser welding conditions could be determined for joining Inconel 718. In particular, the research results indicate that Nd:YAG-laser welding technology can achieve defects free, mechanically sound welds with narrow fusion and heat effected zones.

Jan 1, 2006

By BARRY BANNATYNE

Gypsum in Manitoba is quarried from the Jurassic Amaranth Formation a1 Gypsumville and Harcus; it has been mined near Amaranth and Silver Plains. At Gypsumville, gypsum is carbonate- free but has thin clay laminae between gypsum layers; the rock is folded in places, and some anhydrite is present. At Harcus, gypsum contains scattered dolomite, both as patches in a penemosaic pattern and as thin layers; small chalcedonic concretions also can be found. The quarry at Harcus was opened late in 1978 and currently produces about 100,000 tonnes annually. The two inactive mines near Amaranth operated from 1932 lo 1963 and from 1967 to 1970, and contain a central anhydrite layer. The mine near Silver Plains was flooded from an underlying artesian aquifer in 1975 and has not been reopened. Manitoba gypsum is used in cemem plants in Mani1oba and Saskatchewan and in wallboard plants in the three Prairie Provinces.

Jan 1, 1984

By W. L. Ennis

Introduction This paper outlines the causes of underground fires at Noranda Mines and the precautionary measures taken to guard against such fi res. Shafts There are six shafts (Figures and lA) on the property, of which N os. 1 and 2 are abandoned. Nos. 3, 4, and 5 are the present working openings from surface and No 6 is an internal shaft. No. 3 is used primarily as a service shaft, while Nos.?1 and 5 are the main hoisting shafts. Orebodies The orebodies are of two distinct types. There are the massive sulphide bodies, and the areas of mineralized rhyolite containing gold values and a silica content high enough for fluxing purposes. The massive sulphide bodies contain chalcopyl&apos;ite, pyrite, pyrrhotite, and minor amounts of sphalerite and magnetite. The concentration of particular sulphides varies even within the same body. It is the areas high in pyrite, and to a lesser degree those, high in pyrrhotite, that are of particular interest.

Jan 1, 1950

By R. V. Hopper, M. E. Wilson, L. S. Trenholme

"The Company known as Rouyn Merger Mines, Limited, was formed in 1943 to take over the ownership of claims in Rouyn and Joannes townships formerly held by East Rouyn Mines, Limited, O'Neil Thompson Mines, Limited, and the Hosking-Cockeram Prospecting Syndicate. The NorandaSenneterre branch of the Canadian National railway passes in an approximately east-west direction through almost the entire length of the property. Since 1937, sixty-three diamond drill holes have been drilled from the surface to cross faults on the contact of the Timiskaming sediments with the Abitibi ( Keewatin) volcanics, along which ore has been found to occur. Late in 1945, the sinking of a 3-compartment inclined shaft in the andesite agglomerate beneath the ore zone was commenced. On January 17th, 1947, this shaft had a depth of 944 feet; cross-cuts have been driven north-northwest from the shaft at 150-foot intervals from depths of 200 to 800 feet on the shaft (Fig. 2).GEOLOGYThe western or East Rouyn part of the Rouyn Merger property in which ore is being mined adjoins the area owned by McWatters Gold Mines, Limited, on the east and is underlain by the eastern continuation of the McWatters formations. As at the McWatters, the rocks belong structurally to three areas: (1) the territory north of the Cadillac-Bouzan Lake fault, occupied almost wholly by Abitibi ( Keewatin) volcanics; (2) the area along the south boundary of the property, underlain by Timiskaming conglomerate and greywacke; and (3) the synclinal belt of McWatters volcanics and sediments between areas 1 and 2.1Bouzan fault of Hawley."

Jan 1, 1954

By P. A. Christopher, R. H. Pinsent

"The Adanac molybdenum porphyry deposit near Atlin, in northwestern British Columbia, was discovered in 1905. It was explored extensively between 1967 and 1980.The deposit is within a complex, multi-phase, quartz monzonite stock that is a satellite of the post-accretionary, Surprise Lake Batholith. Biotite K-Ar dates range from 703 ± 2.4 Ma to 71.6 ± 2.1 Ma, indicating a Late Cretaceous age of emplacement.The deposit comprises an irregular-shaped ring or halo peripheral to a quartz monzonite porphyry dome, or ""cupola': The shape of the ring, and of a smal~ fine-grained quartz monzonite intrusion, and the presence of higher-grade mineralimtion on the eastern flank of the cupola, suggest partial control by a preminera/ structure. The deposit is truncated by a steep, northwesterly dipping, normal fault (Adera Fault) that down-dropped the northern half of the deposit by a minimum of 100 mThe deposit lacks strong zonal alteration but there are narrow envelopes of potassic alteration around some veins and local zones of intense wall-rock silicification. There is considerable retrograde alteration along postminera/ faults and fractures.Molybdenite occurs in veins and fractures, many of which are relatively flat-lying. They occur in all phases of quartz monzonite. Molybdenum is the only element of economic significance. There are vein and skarn occurrences with tungsten, tin, lead, zinc and precious metals peripheral to the deposit.In 1981, Placer Development Limited reported an ""undiluted mineable mineral reserve"" of 151 971 000 tonnes grading 0.063% Mo at a cutoff grade of 0.04% Mo and a strip ratio of 1.5:1."

Jan 1, 1995

By S. M. Bulatovic, D. M. Wyslouzil, K. R. Rawlings

"The suitability of a new organic reagent DS20 as a depressant for oxidized and carbonaceous pyritic lead-zinc ore from Nanisivik Mines Ltd. has been evaluated in the laboratory and in the plant.The depressant DS20 is a mixture of Lignosulphonate-Dextrin-Quebracho and was developed specifically for depression of highly oxidized and carbonaceous pyrite.The laboratory test work indicated that the poor metallurgy resulting from the oxidized ore could be improved to normal plant performance by the addition of the DS20 depressant with the existing plant reagents. The laboratory data suggested that lime consumption could be reduced when using DS20.In this paper, the development work and the plant trials with DS20 are described.INTRODUCTIONNanisivik Mines Ltd. treats approximately 2000 tonnes per day of lead-zinc massive sulphide ore, containing currently 1% Pb and 9% Zn. The concentrator operations have been described previously (1,2) and typical metallurgical performance is detailed in Table I.The concentrator flowsheet (Figure No. 1) and the standard reagent scheme (Table No. 2) demonstrate the relative simplicity of treatment of this coarse grained ore.A recently discovered satellite orebody - Area 14 - containing 2% Pb and 12% Zn was brought into production in October 1983. This ore had been oxidized to varying degrees by ground water; the pyrite mineralization was found to be very fast floating and a carbonaceous constituent present in higher than normal proportion also affected flotation. The simple high lime addition could not control the pyrite, and very low grade lead concentrates resulted; zinc metallurgy was also affected by this oxidized condition (Table 3)."

Jan 1, 1986