Search Documents

By P. C. Parsons, G. C. Milligan

"IN FIELD WORK in the Cape Breton Highlands, which are heavily covered with vegetation, it is necessary to run traverses along the valleys of small brooks. We encountered difficulty in closing such traverses, and the following technique was developed to solve this problem. It has been tested in the field for four seasons by several people, and found to be simple, efficient and more accurate than any other compass-and-pace system of which we are aware. So far as we can find, the technique has not been described previously. It may be of use to others.The Cape Breton Highlands of Nova Scotia consist of hills of old intrusive and metamorphosed sedimentary rocks protruding up to 1,000 feet above the general level of the younger sediments which underlie the valleys. The flat hill-tops are the remnants of a plateau; drainage off the edge of this plateau has produced many small steep brooks. They occupy valleys which are up to 800 feet deep, and V-shaped in cross section, with steep sides covered by mixed conifers and hardwoods. The stream at the bottom is rarely more than a few feet wide, with a negligible meander belt, but with many bends, rapids and falls. Visibility along the stream, in consequence, is rarely more than a few hundred feet, and in many places much less.It was found impractical to map the streams by the method of meander lines, as described in many standard surveying texts and hand-books. The limited visibility, and the numerous bends of the brooks, necessitated many corners. Every corner introduces errors. To 'close' a survey with 40 or 50 such corners proved either very time-consuming or impossible. In most cases, however, the general direction of a valley may be obtained from an aerial photograph, or by direct observation, and this became the basis of the method adopted."

Jan 1, 1971

By George Kellock

In presenting this paper for discussion at the Western Annual Meeting to be held in Edmonton, it is with the idea of creating a full and general discussion by the mining men in the Province as to the best way to eliminate, or at least hold down to a minimum, the dangerous coal-dust which is made in mining pitching seams in our Alberta mines by the chute method. Also, an alternative method is outlined, whereby the percentage of lump-coal mined can be increased, and the mining costs reduced-although the paper does not go into any detailed consideration of costs. The general trend of mining practice and lay-outs is at present towards mechanization, and the results being accomplished by the substitution of machines for manual labour are fully justifying the changes. In the technical mining journals, there are published from time to time papers dealing with a variety of methods of mining, which are descriptions of actual operations, and a great deal of interesting and valuable data is given as to the comparative values of the different methods, insofar as the percentage of grades of coal produced, the cost of production, etc., are concerned; but the mechanical methods described in these papers are nearly always suitable only for flat seams, or seams with a very low inclination.

Jan 1, 1929

"Previous studies on the effect of polytetrafluoroethylene addition during chalcopyrite leaching under conditions similar to those of the CESL process have reportedly resulted in complete leaching of the copper without the need for grinding of the flotation concentrate. However, these studies employed a pulp density of only 1% and finely sized PTFE particle that required the use of high impeller rotation rates that are not sustainable at an industrial scale. This paper explores the performance of 1/8” diameter balls of PTFE, that readily sink in the leach solution, on leaching performance at impeller rotation rates and ore pulp densities more typical of industrial practice. Possible routes for separation of the PTFE from the leach residues and their regeneration for recycling back to the leaching stage are also discussed.INTRODUCTIONChalcopyrite, CuFeS2, is the most important primary sulfide source of copper. While pyrometallurgical smelting of chalcopyrite remains the only widely accepted route for treating chalcopyrite concentrates, several medium temperature pressure oxidation processes are claimed to be economically feasible (Muir & McDonald, 2007). Among these, the CESL process has been extensively piloted and demonstrated at the prototype scale. The overall process chemistry of the CESL process may be summarized as follows (Marsden & Wilmot, 2007):4CuFeS2 + 5O2 + 4H2SO4 ? 4Cu2+ + 4SO4 2- + 2Fe2O3 + 8S0 + 4H2O (1)4CuFeS2 + 17O2 + 2H2SO4 ? 4Cu2+ + 10SO4 2- + 4Fe3+ + 2H2O (2)Though copper extractions of over 95 % are achieved, the CESL process requires extra grinding of the concentrate (Muir & McDonald, 2007). This is because leaching is conducted at temperatures around 150 °C, where the elemental sulfur produced is molten and grows thicker on the mineral’s surfaces as oxidation progresses, creating an increasingly large barrier for mass transport. In addition, the sulfur is sticky and tends to cause the mineral particles to agglomerate, effectively halting further oxidation of the particles that end up embedded within the agglomerates. Consumable surfactants, such as ligin sulfonate, have been shown to be effective at avoiding agglomeration, but they are not effective at removing sulfur from the minerals. Hence, their use does not obviate the need for fine grinding."

Jan 1, 2012

By W. N. B. Armstrong

CORROSION of metals, for the purpose of this talk, may be divided into two general classes, namely, atmospheric and chemical. Atmospheric corrosion is caused by the natural agents -water, air, salt, and temperature -as well as by the agents arising from industrial operations which pollute the atmosphere. Chemical corrosion affects metals in refineries and chemical plants where severe conditions exist due to .acids, alkalies, salts, solvents, gases, ?steam, etc. A special condition is encountered on road equipment and motor vehicles due to the large amounts of corrosive salts which are used on our roads in the winter. Exposure to corrosive conditions such as those referred to above causes metal to be destroyed and, therefore, it has to be protected. The non-metallic or organic coatings used to protect the metal are themselves destroyed ultimately by these same conditions. Since all types of organic coatings do not have the same kind and degree of resistance to degradation, a particular kind of -coating must be used for a particular set of conditions in order to obtain the maximum benefit. In ?addition to the above mentioned agents, organic coatings are degraded ?by sun-light, which is probably the severest single factor in the breakdown of organic coatings exposed outdoors. We can divide organic coatings, in a general way, into the following classes: (1) Conventional coatings, and (2) Special coatings.

Jan 1, 1958

By D. G. Minnes

Talc has been mined at Madoc since 1896, the oldest mine in continuous operation in Canada. Canada Talc Industries Limited operates the Henderson and Conley deposits by underground methods. A newly discovered East zone is being de veloped by open pit. The raw Henderson talc is a foliated talc schist of high purity and whiteness; Conley talc is a white talcose dolomite. Products are used primarily as fillers in paints, plastics and rubber.

Jan 1, 1984

By C. H. Hopper, D. R. Derry, H. S. McGowan

"The property of Matachewan Consolidated Mines is in the Matachewan area on the west side of Montreal river. It lies in the western extension of the Kirkland Lake sedimentary belt. The first discovery of gold on the property was made by S. Otisse, in 1916. The property was taken over by Ventures, Limited, in 1933 and production commenced in late 1934. To date (December 31st, 1947) it has amounted to 2,308,800 tons, from which gold and silver to the value of $9,567,600 has been recovered. The mill is currently treating 650 tons of ore a day.GENERAL GEOLOGYThe deposits lie close to the south contact of a belt of sediments striking in a general east-west direction. The sediments, presumed to be of Timiskaming age, consist of light buff arkose and greywacke, containing small pebbles. The Keewatin volcanic rocks to the south are andesites or basalts with cuff and agglomerate bands developed especially near the contact with the sediments. The lavas and sediments are overlain by relatively flat-lying sediments of the Cobalt series to the south and west of the mine, but these later sediments are not involved in the mineralization under discussion. The Keewatin lavas and Timiskaming sediments are intruded by dykes and lenses of red syenite porphyry that have approximately the same strike and dip as the invaded rocks. Later diabase dykes, apparently post-ore, run in a north-south direction and cut all rocks except the Cobalt series.OREBODIESThe gold-bearing mineralization forms bodies of two different types: (1) Within the volcanic rocks irregular orebodies with limited vertical extent. These consist of a series of flat-dipping quartz stringers and adjacent lavas and /or cuffs fractured, bleached, and mineralized with pyrite and gold. They are higher grade than the second type (average about 0.16 oz. gold a ton) and formed the main source of ore for the first 5 years of production. They are described in more detail than can be given here in an article by C. H. Hopper (4). More recent work on deeper levels has failed so far to find orebodies of comparable grade, though low-grade mineralization of a similar type does occur on the projected rake of the main group of the 'basalt type' of orebodies."

Jan 1, 1954

By Marc Piard

In a cool mine, tapping high-pressure lines through reducing valves lowers the temperature beyond remedy. It is the writer's suggestion that, for low-pressure work, law-pressure air ,should be generated in a compressor installed underground adjacent to the work, and that the jacket-water of the compressor should be utilised for re-heating purposes. Such a system of compressed air distribution, designed especially for service in cool mines, is described in the following notes. The suggested system includes a three-wire pole line from the sub-station to the opening nearest to the working face, with a cable connection extending to the latter from the openings; an electrical centrifugal unit; a reservoir excavated in the ground; and a distribution line, re-heated by jacket-water. As regards the reservoir, it may be pointed out that in many mines there are blind or abandoned tunnels that could be used for the purpose. The centrifugal type of compressed air machine is a comparatively new departure, and it was formerly considered that such a machine, operating at less than 1,000 kilowatts per unit, would be commercially impracticable. At the present time, however, these machines are being built in Europe for as little as 400 kilowatts per unit, and as much as 110 lb. per sq. inch pressure. One advantage which these centrifugal machines have over other types is that they may be driven by plain induction motors, without the help of special starters-a consideration of the first importance where the electrical regulations are severe.

Jan 1, 1926

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By Fatemeh Pourakbari, Mohammad Reza Yarahmadi, Abbas Sam

Pyrite is the most abundant sulfide gangue mineral in copper porphyry ores. In spite of addition of lime in large quantities to depress pyrite in flotation, considerable amount of this mineral is reported to concentrate, particularly in rougher and scavenger stages. With the Sarcheshmeh pit advancing to a greater depth and reaching to the hypogene zone, the amounts of pyrite and chalcopyrite in the feed are increased. Hence, a reduction in the copper grade and increase in the sulfur content of the concentrate are observed. In this study the effective factors on the pyrite floatability at the circuit flotation was considered at Sarcheshmeh Mine. Mineralization zones in the pit were firstly identified. Then, sampling points were located using GPS system. On the basis of mineralogical composition and morphology, the ore was categorized into five main classes. In this classification the amount of lead and zinc and also pyrite locking with other minerals were analyzed. The study of polished section indicated that inclusion in pyrite was very frequent in all classes, mostly composed of the floatability of pyrite. Flotation tests were performed on the samples of different classes at pH of 11.8 after conditioning time. It was shown that, pyrite floatability was decreased with a decrease in the lead content of the feed samples except for the second class, while for all classes an increase in zinc content contributed to a decrease in pyrite floatability and recovery. It was found that, the lowest pyrite recovery (1.89%) was corresponding to pyrite–molybdenite dominant mineralization with Zn of 0.33% and the highest recovery (86.89%) corresponding to pyrite vein dominant mineralization with Zn equals to 0.9%.

Jan 1, 2016

By Perry L. Christian

"Mana/ta Coal Ltd. 's Costello Mine, located seven kilometres east of Estevan, Saskatchewan, has been operating at the present location since 1960. During the past twenty-three years, annual production of lignite coal has averaged 590 000 tonnes. The coal is used for power generation and for industrial and domestic use. Markets, operating techniques, facilities in place and reclamation are discussed. Introduction The Costello Mine (formerly the Klimax Mine) is located in southeastern Saskatchewan, approximately 210 kilometres southeast of Regina and 5 kilometres from the United States' border, as shown in Figure 1. The present mine, 7 kilometres east of the city of Estevan, has been operating since 1960. The history, however, of the Costello Mine and of the Estevan Coalfield dates from the initial settling of the area in the 1880s. Mining initially consisted of burrowing into the side of the Souris River Valley or other hillsides where the coal seam was exposed. Eventually, slopes were put down in the Estevan/Bienfait area and vigorous underground activity existed. In the late 1920s surface strip mining was introduced. The use of strip mining progressed to the point where it completely replaced underground mining in the 1950s and it is the only method in use today. During the past 23 years annual production has averaged 590 000 tonnes. The lowest production was in 1960 when the mine was starting up at 167 000 tonnes and the highest production was in 1977 when production was 1 509 000 tonnes. The Costello Mine controls approximately 11 400 hectares of mineral rights in the Estevan area. This is made up of 4 900 hectares of freehold coal and 6 500 hectares of leases. The area forms a large, irregular shaped configuration. Most holdings are contiguous and adjacent. The mine also owns some 8 400 hectares of surface rights. The lands under the Costello Mine's surface rights control, which are not being used in the mining operation, are leased to local farmers and ranchers. This ensures that the land is used to its full potential, both before and after mining."

Jan 1, 1985

By E. Esmaeilzadeh

There arc 8 primary ball mills in the concentrator plant and their task is material crushing. At the time of balls charge to mills, a lot of noise is produced. This noise would affect all grinding areas. The aim of this research was a reduction about 16 dB at source sound power level (SWL was 129.1 dB). With considering two noise control principles, noise producer sources and propagation paths were specified. For removing and reducing of noise producer sources, rubbers with a thickness of 5-20 mm were used on the all inside surfaces of charge box, ball transferring box and exit canal. For increasing transmission loss and damping coefficient of charge box body, rubber with thickness of 1 cm at outside surface of box was used. For reduction of noise propagation a secondary metal cover was designed and made. This cover includes two parts and was set around the charge box. Glass wool (75 kg/m3) with 10 cm thickness was used as acoustical absorbent between free space of two body's layers and from secondary cover side. The of the rest space was left empty. After installing of secondary cover on the ball charge box no.4, SWL showed a reduction about 16 dB. For studying of control system effect on noise reduction at points far from of charge place, measuring results at these points showed the maximum reduction 12.1 dB and the minimum 11.8 dB.

Jan 1, 2007

By Amin Saravari, Jamal Jafari, Abbas Sam

"The fourth concentrate production plant includes the comminution systems and the medium-low intensity magnetic separators (LIMS). Based on different conditions, two types of materials are fed into the plant. Type A: 70% of mine ore and 30% of reject materials from magnetite plant and type B: 100% of mine ore. The goal of the present study was to increase the iron grade and the blain number with low sulfur content in final concentrate as the pellet feed. An appropriate pellet feed should have more than 67% of iron, less than 0.1% of sulfur and a Blain number of more than 1800 cm2/g. The Fe, S and Blain no. amounts for the present concentrate are 66.6%, 0.95%, and 500 cm2/g (feed type:A) and 67.8%, 2.3%, and 450 cm2/g (feed type: B), respectively. In this research, the plant improvement efficiency was evaluated by changing the feed particle size distribution and using the flotation system. Laboratory experiments were designed based on the three circuits:1) LIMS (Low Intensity Grinding Rolls) feed grinding-LIMS test-flotation test2) LIMS feed grinding-flotation test-LIMS test3) LIMS concentrate grinding-flotation testThe best results were obtained using the first circuit at the LIMS feed size (d80) of 132 ?m. The processing results using the circuit no. 1 (feed type: A), showed a LIMS concentrate with 69.8% of Fe and 0.36% of sulfur. In this case, the final concentrate (after flotation) with Fe grade of 70.3%, sulfur content of 0.07% and Blain no. of 1571 cm2/g were obtained. In case of the feed type of B, the LIMS concentrate with Fe grade of 68.7%, and sulfur grade of 1.6% was achieved. Also, the Fe and sulfur contents were 69.3%, and 0.4% respectively with a Blain number of 1112 cm2/g. According to the obtained results, it was suggested that a LIMS feed comminution along with a LIMS and flotation systems are necessary to achieve an appropriate iron and sulfur grades with an acceptable blain number. To reach a concentrate Blain number as a pelletizing feed, a High Pressure Grinding Rolls (HPGR) system at the end of the processing line was recommended."

Jan 1, 2016

By R. W. Allgood

"THE world-wide shortage of elemental sulphur, which became sharply apparent in 1950, has focused attention on the commercial exploitation of sulphur-bearing materials such as pyritic ores, sour natural gas, and smelter gases. Although there •are no known commercial deposits of elemental sulphur in Canada, there are vast quantities of these sulphur-bearing materials. The International Nickel Company of Canada and Canadian Industries Limited have for many years collaborated in an effort to develop economic processes for the recovery of sulphur from the smelter gas arising from Inco's metallurgical operation at Copper Cliff, Ontario. While sulphuric acid has been •produced at Copper Cliff for over twenty years, recent developments will result in a 60 per cent increase in acid production early in 1952 and, later in the year, in commencement of the operation of the largest single unit ever erected for the manufacture of liquid sulphur dioxide.The purpose of this paper is to discuss •briefly the general factors associated with the recovery of sulphur from the Copper Cliff smelter gases and to describe the sulphuric acid operations and the liquid sulphur dioxide development.Processes for the manufacture of elemental sulphur, liquid sulphur dioxide, and sulphuric acid from sulphur-dioxide-bearing smelter gases are well known and in some cases •highly developed."

Jan 1, 1952

By T. Patching

"COAL MINING at Canmore, Alberta, began in 1886 and continued there until July 1979. A comprehensive review of the Canmore operations is not available, but the following notes have been prepared to accompany references where more complete information about the operations and problems encountered may be found. The coal measures at Canmore occur in the Kootenay formation of Lower Cretaceous age, and at least twelve seams of varying thickness and horizontal extent have been recognized. The coal, of high quality, ranges from semi-anthracite in the lower seams to low-volatile bituminous in the upper seams. The strata of the Canmore area form an asymmetric syncline, the western limb being overturned to vertical by the Palaeozoic strata of the Mount Rundle Range. The eastern limb is more gently sloping, its dip ranging from IO to about 40 degrees. Tectonic movements have created a troubled and complex coal field. The seams were initially not regularly or uniformly deposited, and mountain-building activity folded and faulted the strata and in many places sheared and crushed the original structures of the coal(l,2,3,4,5). The lack of continuity of the seams, and changes in thickness and inclination, made longrange mine planning difficult and necessitated flexible methods of work, and the local disturbances sometimes created problems in roof support and contributed to the occurrence of sudden outbursts of coal and gas. Almost all of the coal was produced from underground operations but a few relatively small V-cut mines were worked along surface outcrops. These have all been filled in and revegetated. The basic method of underground work was by room-and-pillar, but many variations in layout and sequences were employed. Gangways were driven along the strike and pillars were formed by raises or slopes and crosscuts. Pillars were recovered to the extent that ground conditions permitted by splitting or taking 'skips' from the sides of the raises or splits or crosscuts. Because of the variety of conditions that existed in the field a considerable range of cutting, loading and support methods were employed, including hand-loading, slushers and scrapers, duckbills and shaker conveyors, mobile loaders and continuous miners. Except for the coal obtained by continuous miners most of the coal was broken out by blasting when driving narrow working places or by air picks when cutting from a face. In the early years hand loading onto cars or conveyors predominated. A continuous miner was introduced into Canmore in 1959 on a trial basis, and another was subsequently acquired, in order to minimize blasting and hand loading, but problems in operating these machines in inclining seams and difficulties in providing safe roof support for the machines and workers restricted their efficient use. Another major difficulty with the use of continuous miners was the problem of ventilating development headings in the very gassy conditions. In the early 1970s they were replaced by electric and compressed air slushers and scrapers, resulting in a general increase in productivity, roof control, safety, and flexibility of operations(1.6,7,8.9)."

Jan 1, 1985

By J. C. Nicholson

The "V" system was first introduced by the West Virginia Coal & Coke Company at their No. 9 mine, Norton. Norton is a small mining village on the B. & 0. railway, about seven miles from the town of Elkins. This year, accompanied by G. D. MacDougall, I visited this mine to obtain first-hand information regarding this modem system and to determine its adaptability to conditions in Nova Scotia. The following is a brief account of my observations. The seam that is being worked is known as the Lower Kittaning, which, at this point, has an average thickness of 7 feet. This includes a band of hard clay varying in thickness from 8 to 14 inches, which occurs about 2 feet from the pavement, also 8 inches of inferior coal at the roof. The latter is not recovered, which leaves to be mined about 5 1/2 feet of clean coal. The roof is slate and shale for the first 30 feet, followed by 40 to 60 feet of sandstone; the total cover is from 80 to 250 feet thick. The seam lies very flat, with a dip of only 2 per cent., and, as the dip is toward the main entrance, it' is in favor of the load, also providing natural drainage for any water the mine makes. As the mine is not gassy, and there is no water to be pumped out, one can understand that mining conditions are practically ideal.

Jan 1, 1924

By A. Sutherland Brown, Stuart S. Holfand

"The Northeastern part of the Cariboo district lies in the big bend of the Fraser River between Quesnel and McBride. The area shown on Figure 1 extends from just west of Wells to Isaac Lake, about 30 miles across the regional strike of beds.Topographically the area extends from the moderately well dissected Interior Plateau in the west through a transition zone to the fully dissected Cariboo Mountains in the east.The area is an important source of lode and placer gold. The Cariboo Gold Quartz and Island Mountain lode-gold mines have produced more than 32 million dollars in bullion since 1932. Placer-mining has probably produced an equivalent or greater amount, although only 15 million dollars is officially recorded because accurate statistics. were not kept until fourteen years after the origiiaal gold rush of 1860.The regional structure of the Barkerville district was summarized by Lang in the Jubilee Volume (1948, pp. 141-149). Since then a large amount of detailed and areal mapping by the writers has expanded the information available and made necessary a complete revision of the regional geology. Much of the information summarized in this paper, together with a full discussion of the revisions, may be found in British Columbia Department of Mines Bulletins, Nos. 34 and 38, but other information is as yet un-published.Rocks of the Kaza group are exposed in the core of the Lanezi anti-clinorium between Spectacle and Isaac Lakes. The main part of the group is composed of greenish micaceous greywacke and greenish schist with knots of garnet, biotite, or both, and minor amounts of pebble conglomerate. The upper 1,000 feet is composed of white to brown quartzites and brown phyllites. Altogether, about 6,000 feet of the group is exposed. 1t is of latest Precambrian, i. e. Windermere, age."

Jan 1, 1949

By Hans Lundberg

An electric survey from a 'plane flown over the ground is much faster and cheaper than an electric survey carried out on the ground. The results are obtained as continuous recordings that are resolvable into both a depth expression and a conductivity effect, so that the indications are easier to evaluate, as well as to correlate from one flown line to the other. The prospecting technique adopted in our electric airborne surveys may be brie fly described as follows: A loop of many turns of insulated copper cable is fastened around the fuselage of the 'plane and connected to a generator supplying a few ampere alternating current, usually of a frequency less than 1,000 cycles per second. Just as the current in the primary coil of a common transformer will induce current in the secondary coil when shorted, the alternating magnetic field from this primary current now induces alternating current in electric conductors that happen to be located in the vicinity of the path over which the 'plane is flown. This induced secondary current in each conductive section of the ground causes, in turn, an alternating magnetic field, secondary field, which disturbs or dampens the normal alternating magnetic field from the primary loop flown by the 'plane. These secondary fields are then picked up and recorded by the help of detecting solenoids, amplifiers, and recorders carried in the 'plane. By closer study of such a secondary field it is possible to localize the secondary current causing it and, thereby, the conducting body that contains the secondary current. In the 'plane are continuously recorded, besides the amplitude or intensity of the field, also the phase, which is a measure of how much the recorded secondary field is out of step with the primary field.

Jan 1, 1950

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. In order to clarify the failure mode, fracture surfaces after tensile tests were observed by scanning electron microscopy (SEM). The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles, lamellar structure elongated in the rolling direction contains lamellar boundaries was formed. With increasing the strain, mean spacing of lamellar boundaries decreased. Finally, continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. The tensile strength and hardness of the 6 cycle ARB processed 5083 aluminum alloy sheet increased about two and three times of the initial values, respectively. Results indicated conformity between mechanical evolutions and microstructural changes during ARB process. Fracture surfaces observations showed that failure mode in ARB processed aluminum is shear ductile rupture with elongated small dimples.

Oct 1, 2011

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. Moreover the texture parameter of the ARB-ed samples was calculated using their XRD patterns and the related equation. Additionally, the texture evolution during the ARB process was demonstrate by analyzing the measured pole figures and orientation distribution functions (ODF) and skeleton lines. The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. Texture analysis revealed fiber textures have been discovered with continiuose of the ARB process cupper. Brass, S and dillamor textures identify which their differences are in intensity of ARB process. Results indicated conformity between mechanical evolutions and texture evolutions during ARB process.

Oct 1, 2011

By A. Zrimsek, G. Vingas, R. Wolke

IN 1952, prompted by the great demand of the Canadian drilling and foundry industries for sodium bentonite, the Geological Department of Magnet Cove Barium Corporation, Limited began an extensive search for bentonite deposits throughout western Canada. Their efforts were rewarded in 1958, when substantial deposits of high quality material were found approximately 100 miles southeast of Edmonton, Alberta. The bentonite material, a part of the Edmonton formation in the Upper Cretaceous, is located approximately nine miles south of the town of Rosalind. The land where the bentonite lies has in places .been eroded by stream and glacial action to form a wide gully, convenient for strip mining methods (see Figure 1). The bentonite bed is almost flat-lying, dipping to the southwest at approximately 12 feet per mile. The main bed is 8 to. 10 feet thick and is covered with 15 to 25 feet of overburden. Before stripping, the area is drilled and sampled to evaluate the quantity and quality of the bentonite.

Jan 1, 1962