Search Documents

By Robert J. Shank

This paper describes the Federal Government assistance available for northern mining development. The paper commences with a discussion of why the Federal Government should give assistance to northern mining development. It then uses a hypothetical case of a company which has a property it wants to develop to list the sectors within the . Federal Government that would have to be consulted in order to obtain federal financial assistance. The paper also outlines the type of information a company must be willing to provide the government in order to qualify for such assistance.

Jan 1, 1978

By R. Laucournet, E. Billy, M. Joulié

Today Li-ion batteries are considered as one of the most attractive available energy storage solutions. However in order to overcome environmental, legislative and economic issues, the management of used batteries has to be considered and mainly the recycling. The present paper deals with the recycling of used Li-ion batteries and the recovery of high value metals from active materials of electrodes. Lithium nickel cobalt aluminum oxide (NCA) and lithium manganese nickel magnesium oxide (LMNM) cathodes, which contain most of valuable elements typically used in the composition of active materials for Li-ion batteries are investigated by a hydrometallurgy route. The process is divided into two steps: the materials leaching and the elements recovery by a selective chemical separation. Some experimental parameters (acid nature, concentration, time and temperature) are studied to determine the most efficient conditions of dissolution. Then, the valuable elements such as nickel, cobalt and manganese are selectively recovered with a high efficiency close to 100 % and with a high purity by precipitation. By this study, an adaptable hydrometallurgy process can be defined according to the composition of Li-ion batteries to recycle.

Jan 1, 2014

By Shuai-Jun Li, Xia-Ting Feng, Xian-Jie Hao

"The anisotropy of rock is of great importance to the rock engineering. To investigate the anisotropic character of slate, the rock samples of slate under different confining pressures and bedding plane angles was conducted on the MTS. The results indicated that the relationship between bedding plane angle and elasticity modulus, friction angle, cohesion and strength was shown as U pattern. The minimum value of them is located from 30°to 45°.In addition, the elasticity modulus and Poisson's ratio increase with the increasing confining pressure. The slate behaves brittle failure both in the uniaxial and triaxial compression. The failure pattern of uniaxial compression is generally tension failure, and triaxial test usually shows shear failure. The failure angle decrease with the increasing of confining pressure.INTRODUCTIONThe anisotropy of rock is that loading in different orientations the rock has different mechanical properties. The anisotropic property of rock is always an important problem in rock engineering (Hoek E. & Brown E. T., 1980). J. C. Jaeger (1960) first presented that transverse strength criterion for sliding fracture on joint surface. Later he revised rock parameters to anisotropy empirically for isotropic Mohr- Coulomb criterion. His main idea is revising cohesion according to loading direction (J. C. Jaeger, 1971). Then, many scholars study a lot on transverse strength criterion. E. Z. Lajtai (1969) considered the influence of connecting rate in all directions in joint groups for shear strength in intact rock; R. Mclamore and K. E. Gray (1967) referenced the theory of J. C. Jaeger. They not only revised cohesion also revised friction coefficient. Y. M. Tien (2000, 2001) made further study on the influence of connecting rate in joint group to transverse strength. R. Nova (1980) studied on the variation of strength when rock specimens in triaxial pressure and complex stress paths. O. Cazacu(1998) put forwards a new anisotropic strength criterion for analyzing rock strength. S. Pietruszczak(2000) introduced fabric tensor for characterizing inner seismic structure and he built an anisotropic strength criterion containing the invariants of stress tensor and seismic fabric tensor."

Jan 1, 2015

By Z. D. Hora

Limestone of economic interest is widespread in British Columbia. Triassic deposits on Texada Island are a convenient 1idewa1er source of li111es1one for cemen1 and lime for 1he Pacific orthwes1. Permian limes/one near Pavilion Lake is used for quicklime, and a deposit near Kam/oops is used for cement. Quarries at Dahl Lake and Pwrmigan Creek serve local pulp and paper needs.

Jan 1, 1984

By G. Itoh, S. Fukasawa

The Al-Zn-Mg alloys have been known to be susceptible to stress corrosion cracking (SCC), which is based on intergranular cracking arisen from hydrogen embrittlement (HE). The mechanism of HE has not been fully understood yet. In order to elucidate the mechanism of HE, we need to investigate the behavior of hydrogen in the alloys. In this paper, behavior of hydrogen in an Al-5.8%Zn-2.4Mg alloy was investigated by means of hydrogen microprint technique, a method to visualize location of hydrogen emission from specimen surface as silver particles. One side of the tensile test pieces was electrolytically polished and then covered with photographic emulsion. Hydrogen was pre-introduced into the test pieces from opposite side by cathodic electrolytic charging for 30min. Then, the test pieces were stretched with continuing the charging. After that, the specimen was fixed, rinsed, dried and observed with a scanning electron microscope. As a result, silver particles were observed on some grain boundaries.

Jan 1, 2015

By R. J. Rotzinger

The Gibraltar Mine and Mill facility were commissioned in 1972 by Gibraltar Mines Ltd utilizing a flowsheet consisting of two stages of crushing followed by a rod mill / ball mill grinding circuit. During operations a number of opportunities were evaluated to expand the mill capacity; however, the economics of the day did not allow any of these projects to proceed. The mine continued to operate until late 1998 when it was shutdown and put on care and maintenance due to low commodity prices. Taseko Mines acquired Gibraltar in 1999 and in 2004, with the improvement in the metal markets, made the decision to restart operations. During the restart planning a number of opportunities for mill improvements and upgrades were identified and, after operations were successfully restarted, the decision was made to once again review expansion opportunities for Gibraltar. Taseko evaluated various expansion alternatives eventually deciding to install a SAG Mill, convert the existing rod mills to ball mills and distribute the SAG discharge to the resultant six 6 parallel ball mills. This paper discusses the design, implementation and commissioning of the SAG mill grinding circuit.

Jan 1, 2012

By Ali Montaser

This paper presents an experimental study conducted to facilitate the use of RFID on construction job sites. The study focuses on deployment settings to provide data acquisition with higher accuracy for indoor location sensing. It provides extension to the state-of-the-art in this field as it addresses the impact of metal media proximity to RFID tags, the reasonable duration for data capturing, number of RFID tags employed and the distance between them. Low cost passive RFID tags were used in the experiments where each tag is used as a reference point with a known location. Five hundred and forty (514) experiments were conducted in lab environment using a 3m by 3m test bed that is dynamically rearranged to generate 15 test beds and a total of 67713 data sets were collected and analyzed. The collected data were captured from nine locations for each test bed at four time intervals. Received Signal Strength Indicator (RSSI) was used as the main attribute for signal measurement to process the captured data. Results of the data analysis performed are studied under four main categories: duration, number of tags, locations of tags and metal interference. The best duration was found to be the 15 second in the test bed with the least number of tags; as the short amount of time to capture data did not allow creation of a lot of interference among the emitted signals. Within each test bed, errors occurred most at points where the received signals were not well distributed in a 360 degree vicinity of the data capturing point. It means that the center point of each test bed resulted in lowest errors and the points located on the extremities led to the highest errors. Finally, metal objects were found to have major impact on the accuracy of the captured data; to the level where reliable values for errors could not be calculated in the test beds attached to metal objects. In summary, the results of the experimental study and related findings are expected to provide guidelines to the users of RFID technology for localization in building construction.

Aug 1, 2013

By E. Lee Cameron

Summary Records of the past show that the first mineral production in what is now the Province of Manitoba consisted of salt, obtained about the year 1800 by the evaporation of brine. Also at an early time in our history, the Ordovician limestone at St. Andrews Locks, East Selkirk, and other localities was quarried for use as building scone in the construction of forts and fur trading posts. Both salt and building stone are still produced in Manitoba, although not from the original sources. In addition, there is now a substantial production of a variety of other industrial minerals and their products such as lime, crushed stone, gypsum, peat moss, and bentonite. The annual dollar value of production of the industrial mineral industry in Manitoba is today greater than at any time in our past and is derived from a greater variety of products. At the present time, exclusive of the various gravel pits operated by the Provincial Department of Public Works, twenty companies operating thirty-four separate pits, quarries, or mines are producing industrial mineral raw materials in Manitoba. This paper attempts to outline the development of the industry from its start about 1800 to the present, giving general information on the various materials produced. Some suggestions regarding the possibilities of establishing new industries based on other raw materials are given at the end of the paper.

Jan 1, 1949

By Clemens Kuhnert

"Nickelhütte Aue GmbH is specialized in the recycling of waste materials containing non-ferrous metals. We treat nickel, copper, cobalt, vanadium, molybdenum and precious metal containing materials like spent catalysts, ashes, dusts, grindings, liquids, slurries and sludge's as long as they contain one or a combination of the above mentioned metals. In our pyrometallurgical works we produce non-ferrous metal concentrates suitable for further treatment in our hydrometallurgical plant where we refine Ni-, Cu-, Co- and V-chemicals. Our production is based on synergy effects due to the combination of pyro- and hydro-metallurgy. As an example we can mention our heat recovery system and internal recycling of by-products. Furthermore, the use of alternative fuels instead of fossil fuels contributes to the economic and environ-mentally friendly treatment system.INTRODUCTION Nickelhütte Aue GmbH (NHA) can look back on nearly 400 years of tradition as a pyrometallurgical works and recycling company. The existence since its foundation in 1635 as a blue dye works shows responsible and successful action in the past. Therefore, we see highest customer service, minimization of interferences with nature by closing material cycles and maximized health and occupational safety protection by avoiding injuries and diseases, still as our future duties. These duties are evaluated and monitored by an integrated management system that meets the standards of DIN EN ISO 9001, 14001, 50001 and BS OHSAS 18001. We commit ourselves to the observance of all juridical and customized demands. The management and the department managers perceive their model function. We require responsible action from all employees. To protect the continuity of our enterprise, we will also perform in future continuous improvement of products and their quality, as well as steady progress in the areas of environment protection, health protection and industrial safety. Equally the effectiveness and propriety of the management system is checked and developed regularly. In order to obtain the objectives resulting from this policy, our company determines activities and measures by involving all employees."

Jan 1, 2017

By R. R. Culbert

Several thousand parts per billion of uranium are present in some alkaline lake and ground waters of the Okanagan region, British Columbia. To a major extent the uranium content of these highly anomalous waters is controlled by their levels of dissolved bicarbonate. In lakes, dissolved bicarbonate and the organic content of the sediment largely control the partitioning of uranium between sediment and water. This relationship is found to a lesser extent in alkaline creeks, and transported geochemical anomalies in soils appear where uranium-bearing alkaline ground waters have encountered organic materials. There is a possibility that young, near-surface deposits (with very low radioactivity) are forming from these uraniferous waters.

Jan 1, 1978

By D. Sagara, V. G. Makhado

"A model based control strategy was implemented at Loulo Gold Mine in Mali, to stabilise the thickener underflow stream density. This stream acts as the feed to the leaching circuit. pH control of the leaching circuit was integrated with the model-based controller due to slow process dynamics that are not suited to PID control. The controller performance was quantified over a period of 6 months, and was compared to the performance before implementation. The model based controller reduced process variability for both thickener underflow density and pH considerably, and resulted in a reduction in flocculant and lime consumption of 9.32 and 6.55%, respectively. INTRODUCTION Reagent consumption in gold processing plants significantly contributes to the total operational costs. In a typical Carbon-in-pulp (CIP) circuit, the reagent consumption associated with leaching, adsorption, elution and regeneration contribute to approximately 15% of the total operational costs (Stange, 1999). At Loulo Gold Mine, the reagent consumption associated with leaching, adsorption, elution and regeneration contributes to 6% of the total operational costs. As such, a reduction in reagent consumption will present a significant opportunity for savings on operating expenditure. Variability in feed ore characteristics results in continuous changes in steady state operating regions, which presents process control challenges as a result of the long residence times in some of the process units associated with gold processing plants. Overdosing often occurs in the presence of process variability to ensure safe operation and to maintain recovery targets. As a means of reducing reagent consumption and accounting for significant changes in the feed to gold plants, some of the plants have resorted to improving their process control strategies around their circuits. This paper focuses on the implementation of a model predictive based controller at Loulo Gold Mine on their thickener and Carbon-in-leach (CIL) tank to: •,stabilise the thickener underflow density, and •,the CIL tank pH."

Jan 1, 2017

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By N. Behnood, W. Pascheto

"Laboratory wear tests are important tools that can be used for the evaluation of materials for wear applications and mitigation of wear problems in the mining industry. However, laboratory test parameters must be fully characterized and test results must be carefully interpreted if a material selection is to be made. Failure to do so may lead to erroneous conclusions. Suitable lab-oratory tests are valid only if they reflect the field conditions to which materials are subjected. Therefore, it is important to know, in detail, the field conditions, as well as the wear test techniques being considered. It is important to recognize the limitations of the various wear tests and the wear test data published in the literature. This work will review present wear testing technology, including the various wear tests avail-able, wear test equipment and test limitations. Several wear test procedures will be related to common equipment used in the mining industry.IntroductionThis paper will concentrate on non-lubricated wear mechanisms, because they are the most costly to the mining industry. Very frequently we are faced with the task of selecting materials for wear applications or improving existing systems that are giving poor performance. There are plenty of examples in the literature of practical wear cases and ranking of materials for wear applications. It is also very common to find materials manufacturers’ data -sheets listing wear tests results by comparing their materials performances against those of competitors. Much of the published wear data lack the description of the type of wear test, test parameters and the type of wear mechanism to which the data should be applied (if any).Before considering wear test data for a specific problem one should ask which type of wear mechanism is involved? What type of test and what test parameters were used to produce the results? Even if the type of wear tests and parameters are known, how accurate and useful are the published wear data? How are the results related to a particular type of wear? It is important to point out that even the standardized wear tests, such as those in ASTM standards, have limitations. Such limitations are recognized and clearly spelled out in the standards themselves. Basically, wear tests may lead to erroneous results if the test is not able to repro-duce the same wear mechanisms encountered in the field. Therefore, the use of published results may be helpful, as a starting point, but may be of little value for a final material selection.This work will discuss the main types of non-lubricated wear mechanisms encountered in the mining industry. In addition, it will discuss the many wear tests available and their correlation with the various types of wear mechanisms. The limitations of several standardized wear tests and the limitation of using published wear data will also be discussed."

Jan 1, 1997

By A. Klingberg, M. Svensson, N. Smolko Schwarzmayr

"Removal of silicates and carbonates from sedimentary phosphate ores by the use of new synthetic collector/formulations was investigated in a comparative study with traditionally used collector systems as references. In the direct carbonate flotation the new formulations showed higher efficiency, contributed to an improved balance of P2O5 recovery and P2O5 enrichment in the recovered material. Efficiency of the new formulations containing synthetic surfactants was 1.5–2 times better than potassium salt of fatty acid sulfonate based formulations that are traditionally used for that purpose. The new formulations also provided up to 7% increase in P2O5 recovery at the same P2O5 grade. The new synthetic collectors for removal of silicates showed extremely good selectivity towards silica bearing minerals. The selectivity factor for the flotation tests when new formulations were used was 32–52 and for the flotation tests with the traditional collectors: 20–32. The ratio between distribution of an amount of silicates (as SiO2) and distribution of phosphate in the froth (waste) is defined as the selectivity factor. The new formulations provided more than 2% decrease of the amount of SiO2 at the same P2O5 recovery.INTRODUCTIONPopulation growth and decrease of arable land are the main reasons for constant increase of consumption of apatite (phosphate ore) in the fertilization field (Lannefors, Gorochovceva, Klingberg, Lima, & Gustafsson, 2015). Fertilizers play a key role for farmers to produce more with less land. The phosphate component of the fertilizer is vital for producing healthy and large amount of crop. As a result the demand for phosphate rock is growing.The largest producers of phosphate rock are the Unites States, Morocco, Tunisia, China, Russia, and Brazil. The term “phosphate ore” includes all phosphate-bearing minerals and rocks, but only two of them are of industrial interest: apatite (igneous origin) and sedimentary phosphate (Peres, Araujo, El-Shall, Zhang, & Abdel-Khalek, 2007). The majority of the world’s phosphate deposits are of the sedimentary type. There are two different types of sedimentary phosphates: siliceous and carbonaceous which are categorized based on gangue minerals (such as quartz, carbonates, mica, and clay)."

Jan 1, 2016

By Douglas Brand

"The data that many mineral processing plants make use of, is provided by samples taken from sampling systems which are inadequately designed or improperly maintained, and therefore cause detrimental effects to plant operations, production planning and metallurgical accounting! Poorly designed or maintained sampling systems will likely produce low probability samples which give the operator a false sense of security of the product and the process. If data is the basis for action (Flintoff, 1992, p.2), then using the resulting suspect or bad assays by operators, control systems, or metallurgist and administration personnel will act and make decisions which may adversely affect the profitability of a processing plant. Here we will discuss some of the fundamental sampling problems, propagation of errors and a method to estimate what impact this has on an operations Net Smelter Return.INTRODUCTIONIn order to control a mineral processing plant at its best potential, it is necessary to obtain the best possible measurement results of the metal or mineral in question. The sample which is delivered to a measuring instrument, or lab, needs to be of the highest probability to be able to achieve this. This paper will discuss the effects of sampling errors on grade / recovery and grade / Net Smelter Return (NSR) and provide a method to estimate the monetary advantages of using probabilistic sampling in a processing plant.REVIEW OF SAMPLINGSampling, by definition, is the removal of a small representative portion from a total consignment, or flow, for the purpose of accounting or process control.• A sample can only be considered representative, if each and every increment collected, in each of the sampling stages, is representative.• Each particle of the sampling lot must have the same probability of being included in the final sample.• If both of the above conditions are met, then the final sample will be representative of the complete sampling lot.It is commonly known that in order to take truly representative and probabilistic sample, best practices indicate that:• The total stream should be sampled.• The sample cutter should intersect the sample at right angles to the flow.• The sample cutter should travel through the stream at a linear and constant speed and the speed deviations should be less than 5%."

Jan 1, 2016

By A. E. Boudreau

Abstract-It has long been recognized that platinum-group-element (PGE) deposits in layered intrusions preferentially occur in intrusions that crystallized from high-Mg parent magmas. Recent studies suggest that evaluation of any given intrusion for economic PGE potential should also include assessment of the PGE, sulfur and chlorine concentrations in the cumulates and potential parent liquids. PGE: Magmas that contain relatively abundant Pt and Pd are the best candidates for forming economic deposits. Although analyses of coeval sills and dikes are the best indicators of primary magmatic PGE concentrations, analysis of the cumulates themselves is also valuable. For example, within the Stillwater complex, background PGE values in cumulates from the ultramafic sections of the complex contain, on average, several 10s of ppb Pt and Pd. Background concentrations of this order are suggestive that the magma was not depleted in the PGE. Sulfur: Conventional petrogenetic models for the formation of PGE deposits in layered intrusions require the PGE to have been concentrated during a magmatic sulfide-saturation event. In contrast, some hydrothermal models suggest that sulfur and the PGE were mobilized from footwall cumulates by upward- migrating, high-temperature hydrothermal fluids. Both models suggest that significant PGE deposits are likely to occur at and below the level where stratigraphic increases in whole rock sulfur concentrations occur. Chlorine: In both the Stillwater and Bushveld complexes the cumulate sequences below the major PGE-bearing zones contain anomalous Cl-rich apatite. The chlorapatite component of apatite in these rocks may exceed 40% and, in the Stillwater complex, typically exceeds 90%. It is stressed that pristine igneous mineral analysis and not whole rock data be used, as whole rock Cl concentrations may be affected by very localized (grain boundary), low-temperature alteration. Intrusions that crystallized from high-Mg, high-Cl magmas appear to have the best potential to host significant PGE deposits.

Jan 1, 1995

The Curtin University Gold Technology Group has been involved in surveying, modelling and optimisation of batch centrifugal concentrator type gravity circuits and CIP/CIL circuits for nearly two decades. The most commonly asked question regarding gravity recovery is, “What is the benefit of a gravity circuit”, which can be hard, if not impossible, to quantify. With the help of the AMIRA P420 Project’s Integrated Liberation Leach Model (ILLM) it is now possible to evaluate the effect of gravity recovery on total gold recovery when changes are made to the grind size, gravity and/or leach/adsorption circuits. This paper demonstrates how the ILLM can be used to determine the net benefit of introducing or modifying a gravity circuit and assess the effect of operating conditions (grind size, coarse gold size distribution, leach residence time, carbon activity, etc.) on plant performance.

Jan 1, 2017

By M. H. Cullender

THE determination of the flow characteristics of gas wells depends upon the analysis of pressure data obtained under shut-in conditions and under one or more known flow conditions. These data are commonly referred to as back-pres-sure test data, and I know you are all familiar with the back-pressure equation where, Q rate of flow, Mcfd @ standard conditions C coefficient of the back-pres-sure curve P 1 formation pressure, psia P • sand face flowing pressure, psia P2 (psia)2/1000 n exponent of the back-pres-sure curve Figure 1 is a graphical presentation of the back-pressure equation; the coefficient is the rate of flow at a difference in squared pressures of 1, in this case 2250 Mcfd, and the exponent defines the manner in which the rate of flow changes with a change in the difference in squared pressures. In Figure 1, the exponent of the back-pressure curve is 0.554 which means that for a 10-fold change in the difference in squared pressures, there will be a 3.58-fold (10 raised to the 0.554 power) change in the rate of flow.

Jan 1, 1961

By A. E. Boudreau

It has long been recognized that platinum-group-element (PGE) deposits in layered intrusions preferentially occur in intrusions that crystallized from high-Mg parent magmas. Recent studies suggest that evaluation of any given intrusion for economic PGE potential should also include assessment of the PGE, sulfur and chlorine concentrations in the cumulates and potential parent liquids. PGE: Magmas that contain relatively abundant Pt and Pd are the best candidates for forming economic deposits. Although analyses of coeval sills and dikes are the best indicators of primary magmatic PGE concentrations, analysis of the cumulates themselves is also valuable. For example, within the Stillwater complex, background PGE values in cumulates from the ultramafic sections of the complex contain, on average, several 10s of ppb Pt and Pd. Background concentrations of this order are suggestive that the magma was not depleted in the PGE. Sulfur: Conventional petrogenetic models for the formation of PGE deposits in layered intrusions require the PGE to have been concentrated during a magmatic sulfide-saturation event. In contrast, some hydro thermal models suggest that sulfur and the PGE were mobilized from footwall cumulates by upward-migrating, high-temperature hydrothermal fluids. Both models suggest that significant PGE deposits are likely to occur at and below the level where stratigraphic increases in whole rock sulfur concentrations occur. Chlorine: In both the Stillwater and Bushveld complexes the cumulate sequences below the major PGE-bearing zones contain anomalous Cl-rich apatite. The chlorapatite component of apatite in these rocks may exceed 40% and, in the Stillwater complex, typically exceeds 90%. It is stressed that pristine igneous mineral analysis and not whole rock data be used, as whole rock Cl concentrations may be affected by very localized (grain boundary), low-temperature alteration. Intrusions that crystallized from high-Mg, high-Cl magmas appear to have the best potential to host significant PGE deposits.

Jan 1, 1995

By D. Ofstie, B. Kargutkar

BIM, or Building Information Modeling, is transforming the way metallurgical facilities are built, operated and maintained. BIM provides a digital representation of the facility, complete with all physical and functional characteristics - enabling collaborative planning, concurrent design, construction simulation, sustainable operations and predictive maintenance through a connected information model. Building on experience gained in other industries, Hatch is aggressively applying the BIM process to the mining & minerals processing industry to address inefficiencies inherent in traditional document-based information management. Intelligent 3D models support real-time quantity forecasting and cost trending by commodity type and construction work package. By linking procurement and schedule data, material availability and constructability reviews are visualized to verify construction critical path, ensure work front safety and minimize craft downtime. The BIM digital information model connects engineering, construction, commissioning and vendor data, aiding timely asset-centric handover to plant operating and maintenance systems.

Jan 1, 2015