Search Documents

By Karl J. C. Harries

"6.1. INTRODUCTIONThis chapter comments on some of the more common types of agreements related to property examination and acquisition, other than the farm-in/joint venture agreement or common undertaking, which is dealt with in the next two chapters. Many of the comments made in Part IV of Chapter 4 apply equally to any such agreement. In addition, many of the comments in Chapter 8 and the examples in Volume II are most certainly relevant to many other types of agreement.6.2. RIGHTS OF FIRST REFUSAL1A right of first refusal is a right that obligates an owner to offer his property, or an interest therein, to the holder of the first right if the owner intends to sell or otherwise dispose of it. It may be triggered either by the owner wishing to offer his property for sale or by receipt of a bona fide offer to purchase his interest from an “outside” third party. The mechanics and procedures to implement a first right should be set out clearly in the agreement, and their basics are the same, whether the first right is a stand-alone document or is part of an acquisition agreement.2Rights of first refusal are common in agreements to permit some control over the disposition of an interest and there they can be a valuable provision. However, some explorationists feel that they are also a good stand-alone agreement to have while a property is being evaluated to decide whether or not it is worth optioning. The reasoning is that such an arrangement will tie up the property to allow a quick look and, if the property looks interesting, the balance of the term of the first right will give an ample exclusive period of time to negotiate with the owner and settle an acquisition agreement. In addition, the explorationist is protected by the first right if the owner decides to negotiate a deal with another party."

Jan 1, 2003

By Karl J. C. Harries

"7.1. INTRODUCTIONThis chapter addresses the joint venture and examines a number of general concepts of the joint venture relationship. Chapter 8 looks at some specific concepts related to the provisions of a joint venture agreement, which are equally applicable to a shareholders’ agreement or other contractual relationship. The term “joint venture” is used because the author is a common law solicitor (a matter of convenience for which apologies are offered to civil law readers), but it should be noted that, in many aspects, the legal structure of an entity is irrelevant. It is the relationship of the parties, be they venturers or shareholders, that is important, and the areas of concern are surprisingly similar (except for terminology).The details of the joint venture relationship and agreement could fill several books. Accordingly, this chapter and the next focus on selected topics that appear to have caused problems or confusion or to be the basis for disputes. And remember that, although the following discussion is in the context of a joint venture, many of the comments apply, either directly or indirectly, to virtually any common undertaking and the agreement defining it.For interest’s sake, this chapter starts with a summary of some of the earlier types of agreements and arrangements that have evolved into the joint venture agreement of today in Canada, the philosophy of their format, and the reasons for their demise.7.2. EVOLUTION OF THE CANADIAN JOINT VENTUREThe Early DaysMuch of the opening up of Canada’s north is due to exploration for and development of mines. The early discoverers were relatively free to roam and explore at will and, if they were fortunate enough to find something, they dealt with the appropriate government to acquire exploitation rights. The early interests lay in gold or silver. Workings were small, usually worked by the owner alone or with only a couple of helpers to extract the native gold or silver. If the owner wanted to move on, he could sell his property outright and use his stake to look elsewhere.As logging and mining camps were opened, the development of better roads and railways made access easier. Entrepreneurs saw the opportunity to make money by assembling large parcels of land and working them as a single operation. In order to do this, some owners who were not ready to sell out had to be convinced to do so through more attractive offers"

Jan 1, 2003

By Steve Forgeron, Brendan MacKenzie, Kevin MacPherson

"The geological composition of strata immediately adjacent to coal seams has a significant effect on the safe and efficient extraction of coal from underground mines of the Sydney coalfield. Geological features such as paleo-sandstone river channels, seam splits, floor rolls, paleo-soils and stone-filled rupture features can rapidly alter the competency of immediate roof and floor strata, significantly reduce the height of the coal seam, cause rapid variations in seam gradient and influence the in situ and run-of-mine quality of the coal.The impact of these features on the over-all mining operation can be significantly reduced if mine management can be for-warned of their impending occurrence. Using the information acquired from boreholes, geological mapping, x-ray diffraction analyses, microscopic studies, geophysical logs and seismic surveys, sedimentary models have been constructed which enable the mine geologist to predict, with increasing accuracy, the future occurrence of deleterious geological features ahead of the working face."

Jan 1, 1986

By Michel Garon

"Several years ago computer control of the flotation process was successfully implemented at the Matagami concentrator of Noranda Mines Inc. At that time this was the first computer application being installed at this operation. The last few years have seen an extensive use of programmable controllers in areas such as the copper and zinc dewatering circuits and the lime preparation system. With the aid of such instruments, these areas have attained a high level of automation and as a result, a high degree of efficiency. The controllers have proven to be very dependable and easy to use.IntroductionThe Matagarni Division of Noranda Mines Inc. operates two mines in the Matagami District of northwestern Quebec which is located about 650 km northwest of Montreal. The mines ship ores to a central concentrator whose throughput averages 95,000 tonnes of ore per month. Metal contents of the mill feed average 0.9 per cent copper and 5.0 per cent zinc. Concentrate outputs are approximately 3,200 tonnes of copper and 8,200 tonnes of zinc per month.The concentrator commenced operation in 1963. An on-stream X-ray analyzer was installed in 1968, providing analyses of several samples in the flotation circuit without the aid of a computer. In 1974, control of the circuit by computer was added to the system. As a result, zinc flotation efficiency improved considerably and reagent costs decreased through the reduction of copper sulphate consumption.In the past few years it was realized that significant improvements could also be made in other parts of the operation . Copper and zinc dewatering circuits and the lime preparation system were identified as major areas that could drastically benefit from automation. In 1982, programmable controllers were seriously considered as an attractive alternative for achieving the company 's goal. Because of their relative lowcost and their high degree of flexibility, they were selected for implementing automation and, for improving the efficiency in each of these areas."

Jan 1, 1985

By T. L. Lee, D. Y. Tan, J. Mi

Considerable progress has been made in studying the mechanism and effectiveness of using ultrasound waves to manipulate alloy solidification microstructure, However, uncertainties remain in both the underlying physics of how microstructure evolve under ultrasonic waves, and the best technological approach to control the final microstructure and properties. We used the ultrafast synchrotron X-ray phase contrast imaging facility housed at the Advanced Photon Source, Argonne National Laboratory, USA to study in-situ the highly transient and dynamic interactions between the liquid metal and ultrasonic waves/bubbles. The dynamics of ultrasonic bubbles in liquid metal and their interactions with the solidifying phases were captured in-situ for the first time. The experiments were complemented by the simulations of the acoustic pressure field, the pulsing of the bubbles and the associated forces acting onto the solidifying phases, providing more quantitative understanding for using ultrasound to control the growth of dendritic grains and to enhance grain multiplication effects for grain refinement.

Jan 1, 2014

By A. S. H. Kabir, I-H. Jung, J. Su, S. Yue, M. Sanjari

The final mechanical properties of wrought magnesium alloys are mostly controlled by microstructure and crystallographic orientation or texture. In common magnesium alloys, grain coarsening occurs during annealing process and formation of undesirable basal texture cannot be changed markedly. The aim of this work is to investigate the effect of static precipitation on microstructure and texture evolution during annealing at 250 °C after warm rolling of Mg-Al-Sn alloy. Mg-3Al-3Sn (wt. %) alloy has been designed using thermodynamic modeling software, FactSageTM, based on forming target stable and incoherent Mg2Sn precipitate within the industrial deformation temperature range. Microstructures and precipitation were investigated by optical and scanning electron microscopes and macro-texture was measured by X-ray diffraction (XRD) techniques. It was found that static precipitates form in a large scale at the recrystallized grain boundaries and retards the grain growth during annealing. Slight weakening in basal texture was also observed during annealing.

Jan 1, 2014

By Robert Voisey, Robert J. Spencer

"LynnGold's MacLellan Mine is located about 8 km south east of Lynn Lake immediately to the east of the Keewatin River (Fig. I). The property is accessible by an all-weather road, leading north from the provincial highway 391, which links with the Town of Leaf Rapids and the City of Thompson to the south.The ore body, as outlined in the original feasibility study, is expected to produce in excess of 9.3 x IQ6 gm of gold and silver over the next 5 years. However, the deposit is open to depth and exploration is continuing on and around the main zone and the many satellite deposits.The start of construction of the MacLellan Mine and mill was scheduled to phase in with the closure of the Fox copper-zinc mine located 48 km west of Lynn Lake. The majority of the employees from the Fox Operation were either employed at the MacLellan Mine or relocated to Sherrin's Ruttan Operation.GeologyThe MacLellan gold ore deposit is located on the northern section of the Lynn Lake Greenstone Belt known as the Rainbow Trend. This Trend is a 40 km gold bearing rock sequence extending both east and west from the MacLellan Mine. The southern section of these two east-west trending structures is known as the Johnson Shear, this is also gold bearing."

Jan 1, 1990

By P. H. J. Mercier, M. Couillard

Aberration-corrected scanning transmission electron microscopy (STEM) allows for the nano-scale exploration of materials at unprecedented resolution and sensitivity. In this paper, we combine this approach with electron energy-loss spectroscopy (EELS) and energy dispersive X-ray spectroscopy (EDX) to analyze the carbon distribution in residual solids found in solvent-diluted bitumen product extracted from Alberta oil sands. Major components of these contaminant solids are ultrafine clays. Biwettable clays have been associated with the formation of solid-stabilized water-in-oil emulsion, which are known to increase the content of both water and mineral solids in the final bitumen product. We demonstrate that the residual solids present in bitumen product contain carbon intermixed with mineral particles of various size and shape. By probing the carbon content at the nanometer scale with the high chemical sensitivity of EELS, we provide direct evidence of carbon intermixing with clay platelets. This clay-organic association at the nanometer-scale will contribute to the biwettable, hydrophobic character of the platelets, and will therefore play a crucial role in the bitumen extraction process

Jan 1, 2014

By Scott Hommema

? Bitumen in the oil sand averages Bitumen 12 wt%; water makes up 4 wt% ? Imperial Oil (operator) and ExxonMobil developing Kearl Leases #6, 36, 87 (~200 sq. km) ? Target resource > 4 Billion Barrels ? 3 Phase development, ~100 kbd per phase High-quality resource ? Surface mineable bitumen ? Average properties (full lease) ? TV:BIP < 8 ? Grade > 12 wt% bitumen ? Ore thickness of 40 m ? Overburden thickness of 20 m Status ? Phase 1 ? Front end engineering and design underway ? Detailed engineering to start 2008

May 1, 2008

By D. R. Spink, G. L. Rempel, C. O. Gomez Bueno

"A morphological and chemical study of the Great Canadian Oil Sands Ltd. (GCOS) fly ash has been carried out. Extensive scanning electron microscopy, as well as light microscopy, showed that the GCOS fly ash consists of two fractions, one composed of unburnt or partially burnt irregular-shaped carbon particles and an ash fraction composed of transparent and opaque, often coloured, glassy spherical particles-some of them cenospheres (hollow spheres) and the others plerospheres (hollow spheres packed with smaller spheres). Microcrystals (0.1 to 0.3 um long) growing on the inner and outer surfaces of some of the spheres were also noted and found to contain more Fe, Ti, Ni and V than the spheres.The carbon-free GCOS fly ash particle size follows a lognormal distribution, with a geometric median particle size (by count) of3.8um and a geometric standard deviation of 1.84. IntroductionCanada&apos;s current energy situation strongly suggests that oil from the Alberta tar sands deposits will probably be recovered more extensively in the future. Today&apos;s commercially proven technology to recover oil from the Athabasca tar sands, as practised by Great Canadian Oil Sands Ltd. (GCOS), involves two major operations, namely: separation of the bitumen from the sand and upgrading of the bitumen to refinery oil; the production of significant amounts of petroleum coke and sulphur during the bitumen upgrading process. The bulk of the petroleum coke is burnt in boilers to fulfill the energy requirements of the entire operation. The boiler ash, which contains appreciable amounts of metals, such as vanadium, nickel, titanium, iron, aluminum and other elements, is collected in the boiler hoppers and cyclones of the petroleum coke-fired steam generation plants. Thus, as well as representing a petroleum resource, the tar sands represent a resource for vanadium and possibly other metals providing that metal recovery processes can be developed."

Jan 1, 1980

By T. L. Carpenter

"The presence of excessive water in the Gibraltar East Stage 1 pit initiated studies into the ground-water conditions that might be expected in mining the Granite Lake and Pollyanna pits. Hydrologic information obtained from a pump test program in 1974 indicated that deep-well dewatering could be successfully achieved. In 1976, a deep-well dewatering system consisting of eight wells was installed on the periphery of the Pollyanna pit . it has been responsible for a significant decrease in mining costs.This paper presents a brief summary of the engineering principles involved in the design of the Gibraltar dewatering system and the problems encountered in the installation and operation of deep-well pumps. IntroductionGibraltar Mines is an open-pit copper-molybdenite mine located approximately 230 air miles north of Vancouver in the central interior of British Columbia (Fig. I). The property consists of three separate major orebodies; Gibraltar East, Granite Lake and Pollyanna (Fig. 2). Mining commenced during the summer of 1971, in the Gibraltar East Stage 1 pit. The Granite Lake Stage 1 pit was mined from mid 1974 to mid 1976. The Pollyanna Stage 1 pit is currently being mined and the Gibraltar East Stage 2 is being developed for production. This report is intended as an outline of the studies and tests leading up to and including the installation of the Pollyanna pit dewatering system, the problems encountered and the results obtained.GeneralIn the summer of 1973, mining in the Gibraltar East pit progressed below ""daylight"" on the down-hill side and ground water very quickly became a costly nuisance in the day-to-day mining operations. Mining, maintenance and blasting costs reflected these problems. Concern was also voiced about adverse effects of ground water on pit wall stability. This concern later became a reality in the Gibraltar East and Granite Lake pits. A study was initiated to investigate various methods and costs of dewatering the pit areas. The study included in-pit sumps, deep peripheral wells and a drainage gallery system located below the pits."

Jan 1, 1980

By J. Oliveira, A. R. Barnes, R. Pandher

Sub-stoichiometric roasting of arsenic-bearing copper ores is a well established practice. However, ores containing calcium commonly prove challenging where very low arsenic levels are desired, but the reasons for this phenomenon have largely been speculative. In the course of treating arsenicbearing copper ores by partial roasting in fluid bed reactors, XPS encountered one of these Ca-bearing ores which proved a challenge to roast to acceptably low levels of arsenic. Mineralogical examination of the calcines using a combination of XRD (X-ray diffraction), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro-Analysis) helped to identify the arsenic bearing species and assisted in developing a workable theory on the sequence of reactions occurring during the roast. With the assistance of thermo-chemical modelling, this allowed adjustment of the roasting conditions to minimise the amount of arsenic retention in the calcine in spite of the presence of calcium in the ore and advance the roasting program to a commercially acceptable solution.

Jan 1, 2014

By C. R. Kerr

"This paper describes the revisions to the heating and ventilating system at the Frood-Stobie mill, which resulted in substantial savings in energy costs.IntroductionInco Metals Company, a unit of Inco Limited, is involved in the mining and processing of nickel-copper ores. The Ontario Division of Inco Metals consists of 10 operating mines, with 5 mines and open pits on a standby basis, and 10 pro- cessing facilities, located in Sudbury, Port Colborne and Shebandowan. In 1980, the Ontario Division&apos;s energy expenditures amounted to $87,000,000.Due to the accelerating cost of energy, the Division established an Energy Management Program in 1975 to define, evaluate and implement measures to reduce energy cost and consumption per unit of output by 10% by 1980. This falls in line with the goals set by the mining and metallurgical task force on voluntary energy conservation.To effectively implement the program, Plant Committees were established at each plant and mine area, with an energy management coordinator appointed to coordinate the activities. The Plant Committee&apos;s responsibilities include identifying the major areas of energy consumption, isolating areas with large potential losses and determining what action should be taken to improve energy efficiency.Within a five-year period from 1975 to 1980, the Ontario Division has been able to cut its energy consumption by 8.9 trillion BTUs, the equivalent of 1.5 million barrels of oil."

Jan 1, 1981

By G. W. McDonald

"The mineralogical studies done on Hope Brook ore samples indicated that a heap leach gold recovery process may be possible. In the metallurgicalprogram that followed, column tests confirmed this interpretation. A 9300 tonne demonstration heap leach test, in the late fall of 1985, reaffirmed laboratory results while identifying operating conditions that will have to be addressed in a production heap leach plan. Operating plans, gold recoveries and cost areas will be presented.Another important factor in a successful operation is the environment approach.LocationThe Hope Brook gold deposit is located 5 km inland from Cinq Cerf Bay on the south coast of Newfoundland. Port au x Basques is 80 km west and Burgeo 40 km to the east of Hope Brook. As there are no roads in the area, access to the site is by sea or air (Fig. I). The Hope Brook orebody is near the saddle of three watersheds flowing to Cinq Cerf Brook, Boat Hole Brook and Betty&apos;s Pond. Acceptable solutions to several environmental concerns can be obtained by using the relative sensitivities of these watersheds.The terrain at the site is generally rolling to hummocky with numerous small ponds separated with rock outcrops and patches of peat covering. Tree vegetation is sparse except in the sheltered areas around Couteau Bay and Cinq Cerf Brook. GeologyThe Chetwynd deposit is hosted by the Lower to Middle Ordovician Georges Brook Formation of the La Poile Group, a thick sequence of volcanic and sedimentary rocks.The Hope Brook Zone contains the largest concentration of gold found to date at Chetwynd. The zone occurs as an intensely silicified lens 100 m to 550 m long (average 400 m) by up to 60 m in width and forms the eastern portion of a more extensive, 4 km long , alteration zone trending at 053 degrees Az and dipping 70 degrees southeast.The Hope Brook Zone contains massive finely granular quartz, scattered blue quartz eyes, 3070 to 8% pyrite, minor calcopyrite and trace molybdenite. Barren silicification envelopes the gold mineralization. The zone is flanked to the southeast by a 200 metre thick aluminosilicate alteration zone and to the northwest by a 10 metre barren pyritic siliceous fragmental rock . The original lithology may be either a thick felsic pyroclastic sequence or a quartz porphyry sill that has been altered by hydrothermal processes. Silica flooding of the permeable host was accompanied by gold deposition."

Jan 1, 1989

By H. Langlois

"Included in the Mines Gaspe mining complex located at Murdochville, Quebec, is a copper smelter which comprises a reverberator furnace, two Peirce-Smith converters, an anode furance, and a sulphuric acid plant.The 50% smelter capacity available is supple mentedby custom concentrates for treatment. As these concentrates can be varied and extremely complex many modifications and improvements have been brought about to optimize and make the process more flexible since its inauguration in 1955.IntroductionThe copper smelter of the Mines Gaspe mining complex is located in Murdochville, a small municipality in the heart of the Gaspe peninsula, 90 km northwest of the town of Gaspe .This metallurgical installation has a daily smelting capacity of 650 tonnes of concentrate and an output of 250 tonnes of copper and 900 tonnes of sulphuric acid. Its main components are: a reverberatory furnace, two Peirce-Smith converters, one rotary anode furnace and one acid plant. The gases, which are produced by the converters, are treated at the acid plant then combined with gases from the reverberatory furnace before being vented through a 152 metre high stack .From the beginning of its operation until the present day (1991), the smelter has treated 7 million tonnes of concentrate and 100 thousand tonnes of scrap for a production of 1.8 million tonnes of copper and 2.2 million tonnes of sulphuric acid."

Jan 1, 1993

By Robert B. Parsons

"First down and four to go. In the game Of football, this is not a bad position to be in. However, in this game of political football, it means that there is still a long way to go. The government in Ottawa has concluded an important agreement with one producing province, and now has at least four more provinces to deal with-B. c., Saskatchewan, Nova Scotia and Newfoundland.On September 1, 1981, the federal and Alberta governments took a significant step forward in formulating an oil and gas policy for Alberta and the rest of Canada on signing a comprehensive five-year agreement that covers taxes, prices, incentives and other fiscal matters related to the production and marketing of oil and gas.This month, Tax Notes examines the main features of the agreement, and offers some eye-opening observations of what the new accord could mean for the future of the Canadian petroleum sector in particular and Canadian business in general."

Jan 1, 1981

By Edward Martinez

Laboratory studies had shown that the magnetite contained in serpentine asbestos ore was not uniformly distributed. Ore particles containing chrysotiye fiber responded to a magnetic f field; particles containing little or no chrysotile were essentially non-magnetic. Larger-scale tests, run with a magnetic pulley being fed various asbestos samples ranging in size from 1/4 inch to 5 inches, confirmed that magnetic separation could be used as a concentration step in an asbestos mill. Magnetic concentration was installed at the Black Lake and National mills of Lac d&apos;Amiante du Quebec and has allowed the extraction of lower-grade ore, increasing the life of the mines. In addition, preconcentration early in the flowsheet increased the value of the feed to the fiber recovery section. An increase in fiber production was achieved, as well as a decrease in maintenance costs due to removal of flow-grade tailings early in the flowsheet. Magnetic concentration of a coarse tailings from the mill resulted in recovery of additional fiber previously discarded to tailings.

Jan 1, 1979

Fatalities Incident Four people perished May 15 ? 17, 2006 ??Doug Erickson ??Bob Newcombe ??Kim Weitzel ??Shawn Currie Incident details available at: ??http://www.mediaroom.gov.bc.ca/sullivan_mine/ ??sullivan_mine.htm Outline Immediate facts/observations from incident ?? #1 Shaft Waste Dump closure program ?? Technical investigations under Panel guidance ?? Findings to date and direction ?? Broaden awareness of potential risks

May 1, 2008

By D. T. A. Symons, M. M. Kapnistos

"Gravity profiles were established over five known Middle Silurian pinnacle reef s in Lambton County, southwestern Ontario. The profiles were approximately 3 km long, with stations every 60 m. Four fairly recent technological developments were used which now make the gravity method relatively efficient and inexpensive compared to the techniques available two decades ago. These are: (1) a La Coste-Romberg model G gravimeter to measure the gravitational attraction with a sensitivity of 0.01 mgal; (2) a Sokkisha model B-2 semiautomatic engineers level to measure the station elevations with an accuracy of 0.5 cm; (3) a Huntec FS-3 hammer reflection seismograph to determine the overburden thickness to an accuracy of ± 7%; and (4) a modern microcomputer to process the data sets and mathematically filter the gravity values. Thus, two men can measure and analyze approximately 1 km of profile per day and obtain the residual gravity profile to an accuracy of ± 0. 05 mgal. Positive gravity anomalies of 0.17 to 0.72 mgal were observed along all five profiles that approximately delineate the dimensions of the known pinnacle reefs, which have an average height of 120 m, diameter of 1500 m and depth to top of 575 m. The relative ease of the gravity survey method makes it a cost-effective technique for hydrocarbon exploration in southwestern Ontario. IntroductionPinnacle reefs are important sources of oil and gas. Although the pinnacle reefs in southwestern Ontario are small, they may contain commercial pools of oil and gas because of their proximity to refineries. They are also useful for subsurface storage of gas to meet the winter surge in gas demand.At present, geophysical exploration for new pinnacle reefs is done primarily by relatively expensive seismic methods, which are also limited in southwestern Ontario by prohibitions on blasting. Gravity methods of exploration were attempted more than two decades ago in this region. (Pohly, 1954); however, the level of technology at that time made the method marginal in sensitivity and quite expensive. Several subsequent developments- gravimeters with greater sensitivity and operating ease, ""self-levelling"" levels for elevation control, hammer seismic reflection units for determining overburden thickness and portable microcomputers for efficient data analysis-have significantly improved the precision and cost effectiveness of the gravity method. Five known pinnacle reefs were selected in Lambton County, southwestern Ontario (Fig. 1), to test the effectiveness of integrating these developments to locate and define additional reefs. Isolated reefs were chosen to avoid the problem of the gravity effect s of one reef interfering with those of a neighbouring reef. The surveys were facilitated by choosing reefs with a concession road passing directly over them ."

Jan 1, 1980

By M. W. Mikhail, R. J. Mikula

"Funding has been made available through the National Energy Program to build a mobile fine coal treatment plant. The plant is intended f or field application and also to upgrade the existing pilot plant facilities.Western Canadian coals with high proportions of fines (due 10 their friability) cause high losses of fine coal to the reject and in turn reduce the over-all recovery of saleable coal. Eastern Canadian coals with high amounts of sulphur of ten require crushing to fin e sizes to liberate pyrite and therefore need effective and efficient separation of these fine sulphur particles. The difficulties involved in solving these problems are two-fold. One is the reluctance to experiment in an operating wash plant and the other is that laboratory scale testing often cannot be extrapolated to the plant environment. The mobile fine cleaning plant with its ability to operate at existing coal preparation plants across Canada and with its flexibility in implementing flowsheet option s and close monitoring of fine coal circuit variables, is ideally suited to solve these fine coal cleaning problems. The mobile plant objectives are to design and optimize flowsheets, evaluate and improve fine cleaning circuit operations and 10 lest new process monitoring and control equipment.The schedule for construction and the required resources will be outlined along with flowsheet options and the general R&D philosophy of the mobile plant.IntroductionIn relation to coal preparation technology, Canadian coal s can be grouped as Eastern coal, Rocky Mountain metallurgical coal and Foothills high volatile bituminous coal. The eastern coals have high sulphur contents and in some cases require crushing or even grinding to liberate the fine pyrite . Rocky Mountain metallurgical coals often occur in highly sheared seams which have been subjected to rapid coalification. The high friability of these coals means that degradation during mining, handling and processing is extensive and results in large amounts of fine s ranging between 20 and 60% by mass of the wash plant feed. The widely varying geo logical structure and exposure to the elements results in partially oxidized coals which perform inconsistently in the traditional method of fine cleaning by flotation . Foothills high volatile bituminous coals for thermal use are frequently interbedded with soft shales and bentonitic clays. These clays disintegrate during washing and swell, producing large volumes of tailings. The presence of clays in plant circuits, particularly fine circuits, tends to increase the viscosity and may cause deterioration of the fines density separation and increase magnetite losses. In view of the fact that fine coal cleaning is the most difficult aspect of coal preparation , a research program is being established to study the factors involved and to offer some solutions.A recent performance evaluation of Canadian washeries showed that yield losses in the minus 2 mm coal circuits were approximately ten times those occurring in the coarse coal circuits(1). Because 2 mm x 0 coal represents 30 to 70 per cent of the raw coal, these losses can be considerable . The operating and capital costs of beneficiating minus 6 mm coal are about four to five times higher than for plus 6 mm coal. In the case o f minus 2 mm coal the costs are even higher. The economic importance of the fine coal cleaning cannot be over emphasized and as a result, the CANMET R&D program is geared for fine coal beneficiation."

Jan 1, 1984